SDC Z7730 Series User manual

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7730-32 REV - 10-23 Page 1
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email [e-mail]
Z7730 & Z7732 SERIES
MOTORIZED LATCH RETRACTION & SOLENOID
CONTROLLED MORTISE LOCK
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSTALLATION INSTRUCTIONS
A. Door Preparation:
1. Measure desired height from finished floor and mark a horizontal line on door face and door edge.
2. Place template on edge of door as shown and align lever centerline with marked height line on door. Check the
chart for drilling trim holes on template and only mark holes for lock function being installed.
of Cylinder
of Lockcase
of Lever
(rose trim mounting
holes shown)
Vertical Centerline
Installation Template
C
L
C
L
C
L
of Door Edge
C
L
Height line
C
Lof Lever
Door Edge
Door Face
3/8"
2X 12-24 WMS
5-5/8"
1-1/4”
(1-3/4” Deep)
3/8”
2-1/4”
1-1/2”
(1-3/4” Deep)
*WOOD DOOR
2X 1" Holes
4-3/4" Deep
NOTCH OPENING FOR MOTOR
ON WOOD DOORS ONLY
*

P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7730-32 REV - 10-23 Page 2
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
4-7/8"
3-17/32"
C
L
Strike
Lock C
L
3/8"
3/8"
2X Ø 1" Holes
1-1/8" Deep
C
L
Jamb
A. Door Preparation (Continued)
3. Mortise door edge according to measurements on installation template and drill proper holes for trim.
Dimensions for face plate recess: L 8-1/32" x W 1-5/16" x D 7/32".
5/32"
7/32"
B. Strike & Dust Box Installation:
1. Align strike template on jamb. Be sure to
keep 3/8" distance between lock centerline
and strike centerline. Recess 5/32" for flush
fit of strike and dust box.
2. Mortise jamb according to supplied strike
template. Then fit strike and dust box into
frame and secure into place with supplied
screws.
Wire Raceway suggested for wood doors.
Optional:
SDC Door Core Drill Guide Kit
P/N: 7000-DGK
Rose Trim
Mounting Holes
8-1/32"
1-5/16"
Escutcheon Trim
Mounting Holes
1-5/16"
8-1/32"

LH
Left Hand
LHRB
Left Hand
Reverse Bevel
INSIDE OF DOOR
OUTSIDE OF DOOR
RH
Right Hand
RHRB
Right Hand
Reverse Bevel
INSIDE OF DOOR
OUTSIDE OF DOOR
C. Install Lockcase
1. Verify Handing
Make sure the lock hand matches the door hand, use the following
diagram to determine the hand of door.
If the latchbolt handing doesn’t match the required handing, follow step
1a. If the locked side is on the wrong side, follow step 1b. If both
latchbolt and locked side do not match the required handing, follow
both steps 1a and 1b.
1b. Change Locked Side Handing
Remove hub screw from hub on the unlocked side of lockset. Depress the hub plunger using a narrow rod (e.g., a
small hex wrench) to install catch screw into opposite side of lockset.
1a. Change Latchbolt Handing
Remove the latchbolt screw and pull the latchbolt out from lock case. Turn the latchbolt 180° to change the
handing. Position latchbolt back into case and re-fasten latchbolt screw to opposite side.
LHRB Shown
Continuation of handing conversion from LH to RHRB.
Converted to RHRB
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7730-32 REV - 10-23 Page 3
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
Converted to LH
LH Shown
180°
Latchbolt Screw
Hub Screw
Hub Plunger

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7730-32 REV - 10-23 Page 4
C. Install Lockcase (Continued)
2. Connect wires as shown on the lock cover diagram (or refer to page 7 of instructions).
3. Insert lockcase into mortise cut-out and fasten to door using screws.
D. Install for Rose Lever Trim
1. Install Outside Lever Assembly first.
2. Guide the Spindle Spring over Spindle, then insert Spindle into the outside side of mortise lockset.
3. Insert Collar into Outside Lever Assembly. Guide the Reversible Spring Cage over Mounting Posts with arrows
pointing in direction of lever rotation.
4. Insert the Outside Lever Mounting Post through holes in door.
5. Install Inside Lever Assembly by guiding Reversible Spring Cage over the inside Spindle and Spindle Spring with
arrows pointing in direction of lever rotation.
6. Place Mounting Plate over Reversible Spring Cage and secure by threading Mounting Screws into Mounting Posts.
When tightening screws, make sure both levers are in correct horizontal position when resting.
7. Insert Set Screws into Mounting Plate & secure against door face.
8. Place Rose Cover over Mounting Plate.
9. Thread Inside Lever onto Mounting Plate and tighten using supplied Spanner Wrench.
Spanner
Wrench
Outside Lever Assembly
Collar
Reversible Spring Cage
Mounting Posts
Spindle Spring
Spindle
Spindle
Spindle Spring
Reversible Spring Cage
Mounting Plate
Mounting Screws
Rose Cover
Inside Lever
Set Screws

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7730-32 REV - 10-23 Page 5
D. Install for 07 Lever Trim
1. Install the Outside Lever Assembly first.
2. Insert Spindle into the outside side of mortise lockset.
3. Place the Collar and then Reversible Spring Cage onto the Outside Lever Assembly with the Spring Cage arrows
pointing in direction of lever rotation (DO NOT USE INCLUDED SPINDLE SPRINGS).
3. Insert the Outside Lever Mounting Post through holes in door.
4. Install Inside Lever by placing Reversible Spring Cage over inside Spindle with Spring Cage arrows pointing in
direction of lever rotation.
5. Place Mounting Plate over Reversible Spring Cage and secure by threading Mounting Screws into Mounting Posts.
6. Insert Spring into Mounting Plate.
7. Place Rose Cover plate over Mounting Plate.
8. Thread Inside Lever onto Mounting Plate and tighten with supplied Spanner Wrench.
Spanner wrench
Use standard straight
cam ILCO (863G) or
ILCO (863M) Schlage
“L” cam.
Install Key Cylinder and Armor Face Plate (Rose & 07 Trim)
1. Screw key cylinder into threaded hole of the lock case (Key cylinder not provided).
2. Tighten the set screw against cylinder by turning clockwise as shown.
3. Install face plate onto the lock case and fasten with supplied screws.
863G
863M
Faceplate
Outside Lever
Assembly
Collar
Reversible
Spring Cage
Spindle
Spindle
Reversible
Spring Cage
Mounting Plate
Mounting Screws
Rose Cover
Inside Lever
Key cylinder collar suggested
for Rose & 07 Trim installation
(not provided).
Use screwdriver to
secure key cylinder

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7730-32 REV - 10-23 Page 6
Install Key Cylinder and Armor Face Plate (Escutcheon Trim)
1. Screw key cylinder into threaded hole of the lock case (Key cylinder not provided).
2. Tighten the set screw against cylinder by turning clockwise as shown.
3. Install face plate onto the lock case and fasten with supplied screws.
Use standard straight
cam ILCO (863G) or
ILCO (863M) Schlage
“L” cam.
D. Install for Escutcheon Lever Trim
1. Install the Outside Lever first.
2. Place Spindle Spring over outside Spindle, then insert Spindle into the outside sides of lockset.
3. Insert Collar into Outside Lever Assembly. Place Reversible Spring Cage over Ferrules with Spring Cage arrows
pointing in direction of lever rotation.
4. Install Outside Lever Assembly by inserting Mounting Posts through holes in door.
5. Install Inside Lever by placing Reversible Spring Cage over inside Spindle and Spindle Spring with the spring cage
arrows pointing in direction of lever rotation.
6. Place mounting plate over Reversible Spring Cage and secure by threading Mounting Screws into Mounting Posts.
7. Install escutcheon Cover Plate over Mounting Plate.
8. Thread Inside Lever onto Mounting Plate and tighten with Spanner Wrench.
863G
863M
Faceplate
Use screwdriver to
secure key cylinder
Inside Lever
Escutcheon Cover Plate
Mounting Screws
Outside Lever
Assembly
Mounting Posts
Ferrules
Collar
Reversible
Spring Cage
Spindle Spring
Spindle
Spindle Spring
Spindle
Reversible
Spring Cage
Mounting Plate Spanner
Wrench

E. Lock Wiring
Power &
Controls
FIELD WIRING:
6 COND MINIMUM
18-22AWG
JACKETED CABLE
100' MAX from Power Supply to Lock
Solenoid
Activation
Switch
(Dry, N/O)
PWR LEVER LATCH
+CNO CNO
External Control Board
(PCB135A01-A)
Motor
Activation
Switch
(Dry, N/O)
Motor Activation Switch: Closing the switch for a
minimum of 2 seconds retracts the latch.
Release switch to release latch.
Solenoid Activation Switch: Closing the switch will
provide power to the solenoid.
If the solenoid is fail-safe, activating the switch will lock
the lever.
If the solenoid is fail-secure, activating the switch will
unlock the lever.
24VDC
Regulated &
Filtered Power
Supply
(1.5A min)
SDC P/N 631RF
is recommended.
24VDC (Continuous)
GRY
VIO
BRN
YEL
REX N/O
REX/Latch Status COM
Latch Status N/O
Latch Status N/C
Power
Transfer
Device
6 Cond Min
10 Cond w/ Options
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7730-32 REV - 10-23 Page 7
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
Use
factory
provided
pigtails
Optional
REX and/or
Latch Status
Outputs
Z7700
Series
1A @ 30vdc