SEA USER 1 - 24V DG R1B User manual

USER 1 - 24V DG R1B
SEA S.p.A.
Zona Ind.le S. Atto - 64020 S. Nicolò a Tordino (TE)
Tel. [phone] - Fax [phone]
www.seateam.com
e-mail: [email protected]
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
67411260
23024055
REV. 15 - 11/2017
24V ELECTRONIC CONTROL UNIT FOR SLIDING GATES AND BARRIERS
English

27
DESCRIPTION OF THE COMPONENTS
TECHNICAL SPECIFICATIONS
Control unit power supply: 24 V~
Absorption in stand by: 30 mA
Environment temperature: -20°C +50°C
Specifications of external enclosure: 305 x 225 x 125 mm - Ip55
JOLLY 3
CN8 F1
CN1
CNA
CN3
CN5
CNP
CN6
RL2
RL1
CN2
CN4
CN7
UP DOWN OK
RD3
RD1
PR1
DISPLAY
1 2 3 4 5 6 7 8 9 10 11 12 13
1
EXP
POWER FUSE BATTERY MOTOR LIGHT
MASTER/SLAVE
PROG
RADIO MODULE
JOLLY
LIMIT SWITCH
156 mm
100 mm
RICEVENTE RX
CNE
ENCODER
1COURTESY LIGHT
Cn1 = Input/Output connector
CN2 = Limit switch connector
CN3 = JOLLY 3 connector
CN4 = Master/slave connector
CN5 = Courtesy light output plug
CN6 = Motors connector
CN7 = Batteries connector - Quick connection
CN8 = Power connector
CNA = RX Receiver connector
CNE = Encoder connector
CNP = Programming connector
EXP = External module connector
OK = Programming button
DOWN = Programming button
UP = Programming button
RD1 =Motors piloting Mosfet
RD3 = Motors piloting Mosfet
R1 = Motors command relay
R2 = Motors command relay
PR1 = Rectifier jumper
F1 = Fuse 10 AT
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

28
CONNECTIONS
The herein reported functions are available starting from revision 02.00 compatible with JOLLY 3
Start
Stop
Common
Antenna
START Ped.
Common
Photocell 1
Common
AUX
(24V 200 mA max)
24V 750 mA max
(Accessories)
Safety edge
Flash (-)
Photocell 2
WARNING: The control unit is designed with the automatic detection of not used N.C. inputs (photocells, Stop and Limit
switch) except the SAFETY EDGE input. The exclude inputs in self-programming can be restored in the “Check inputs”
menu without need to repeat the programming (pag36).
Obligatory jumper
without
accessory connection
Limit switch Cl.1 (Yellow)
24V (Red)
Common (White)
Limit switch Op.1 (Green)
LIGHT (CN5)
Max 100mA
POWER (CN8)
24V~
MOTOR (CN6)
M
Max 200W
JUMPERS
123 4 5 6 7 8 910 11 12 13
CN1
ANT COM START PEDST STOP COM PH1 PH2 EDGE AUX COM 24V (FL)-
123 4 5 6 7 8 910 11 12 13
CN1
ANT COM START PEDST STOP COM PH1 PH2 EDGE AUX COM 24V (FL)-
Optional
+ +
- -
+ +
- -
LIMIT SWITCH (CN2)
1
ENCODER (CNE)
1
Brown
White
Green
Start
Stop
Common
Antenna
START Ped.
Common
Photocell 1
Common
AUX
(24V 200 mA max)
24V 750 mA max
(Accessories)
Safety edge
Flash (-)
Photocell 2
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English
29
UP DOWN
5 s 5 s
UP DOWN OK
DISPLAY
1 2 3 4 5 6 7 8 9 10 11 12 13
PROGRAMMING
FAST SELF-LEARNING
Start quick programming
You can start the quick programming by
holding UP for 5 s in the “Input check
menu", until the motor starts.
“Input check
menu"
Fast self-learning START command by
radio control
You can store the START button of the
remote control while pressing DOWN for 5 s
in the “Input check menu".
Once the writing "Press button" appears,
press the button of the transmitter, which
you want to store for the START command.
By pressing OK, you can exit the menu,
otherwise it will be left automatically after 5
seconds.

30
PROGRAMMING
BUTTONS
OK to exit
Menu or press
the button of
the next TX to
be stored
RECEIVER
MISSING
Skip this step if you do not want to program a transmitter
Choose the type of
motor with
UP or DOWN
To confirm and
return
to main menu
Choose "ON" with UP or
DOWN button only if in
programming the motor starts
in opening
With UP or DOWN
choose
the desired logic
With UP or DOWN
choose a delay for
automatic closing
With UP or DOWN
Choose ON
With UP or DOWN choose ON
to start times learning
At the end of the selflearning
the control unit returns automatically
to the main menu
With
UP or DOWN Choose
ON to start test
Skip this step if a TX has already been stored
ALL OTHER PARAMETERS HAVE DEFAULT SETTINGS WHICH ARE USEFUL FOR THE 90% OF THE APPLICATIONS
BUT CAN BE HOWEVER SET THROUGH THE SPECIAL MENU. FOR ENTERING INTO THE SPECIAL MENU MOVE
ON ONE OF THE MENU AND PRESS THE UP AND DOWN BUTTONS AT THE SAME TIME FOR 5 S
If on the display
appears the item:
Check if a receiver
has been connceted
(see page 25)
The gate will execute a CLOSING-OPENING-CLOSING CYCLE
PROGRAMMING
QUICK START
MENU
SEA
SET MENU
SEA
SET MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
OK
1
2
3
5
6
7
8
9
OK
OK
OK OK
OK OK
OK OK
OK OK
OK OK
UP
UP
UP
UP
UP
UP
UP
OKOK
START
MENU
SEA
SET
MENU
SEA
SET MENU
SEA
SET
OK
UP
LANGUAGE ITALIANO
UP
MENU
SEA
SET
(See
page 29)
MENU
SEA
SET
OK
END
15
MENU
SEA
SET
OK
SPECIAL
MENU
16
UP
UP
10
OK
DOWNUP
OK
Go back to menu
9-PROGRAMMING,
replace the gate halfway
and repeat the timing
programming
TRANSMITTERS
MOTOR
REVERSE
MOTOR
LOGIC
PAUSE
TIME
START IN
PAUSE
PROGRAM-
MING
TEST
START
If the motor has
magnetic limit switches,
select "Magnetic"
in the special menu:
104 - SELECT LIMIT SWITCH
PRESS
BUTTON STORED
Skip this step
if you want to work
in half-automatic
logic
To confirm and
return
to main menu
To confirm and
return
to main menu
To confirm and
return
to main menu
To confirm and
return
to main menu
To confirm and return
to main menu
Press OK to return to the
display of the inputs state
Press OK to enter the special menu
Press the
button of the
TX to be
stored
(See
page 29)
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

31
BASIC MENU
MENU SET
1 - LANGUAGE Español
English
Français
Italiano
Start
Dutch
Italiano
Stop
Unloch
External module
Pedestrian Start
Clear memory
Delete a transmitter
End
2 - TRANSMITTERS
3 - MOTOR
MENU FUNCTIONS TABLE USER1 24V DG R1B
Start
Stop
Storing of a command
for unlocking an electric
brake
Italian
English
French
Spanish
External module
Pedestrian Start
Delete single transmitter
Delete transmitter memory
Dutch
“Transmitters” menu output
Start
Pedestrian
Start
Default
Description Set value
Sliding
Joint
Sprint 3 metres
Saturn
Mercury 800
VergL.5 metres
Erg Maxi
Erg
Verg
Sprint 4 metres
Sprint 5 metres
Storm 5 metres
Storm 6 metres
Storm 7,5 metres
VergL.4 metres
VergL.3 metres
Reversible sliding motors
Mercury Fast
Saturn 1500
Erg Maxi Double
Orion No LS
Taurus No LS
B-224 B-800 No LS
B-200 sliding and B-500
Joint
Sprint 3 metres
Saturn
Mercury 800
VergL.5 metres
Erg Maxi
Erg
Verg
Sprint 4 metres
Sprint 5 metres
Storm 5 metres
Storm 6 metres
Storm 7,5 metres
VergL.4 metres
VergL.3 metres
C-500 and Puma
Mercury Fast
Saturn Fast
Saturn Super Fast
Saturn 1500
Erg Maxi Double
Orion (without limit-switch)
Taurus (without limit-switch)
B-224 e B-800
(without limit-switch)
Saturn Fast
Saturn Super Fast
Sliding
Bistable Stop
Pressed once, it stops the
gate; pressed twice, it re-
active the Start command
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

32
WORKING TIMES SELF-LEARNING
1 240
Off Off
Off
On Off
Off
On
Off On
Off
Off
Off On Off
Automatic
2 buttons
Safety
Dead man
Open-stop-close-stop-open
Open-stop-close-open
Press OK to return to the display of the firmware version
and to the one of inputs state
Press OK to enter the special menu
8 - START IN PAUSE
6 - LOGIC
7 - PAUSE TIME
5 - REVERSE MOTOR
9 - PROGRAMMING
10 - TEST START
15 - END
16 - SPECIAL MENU
Synchronized right motor
Automatic
Step by step type 1
Step by step type 2
Two buttons
Safety
Dead man
Setting from 1s to 4min.
OFF
(semi-automatic logics)
In pause start is not acceped
In pause start is accepted
Start command
Times learning start
Synchronized left motor
Open-stop-
close-open
MENU SET
Default
Description Set value
WORKING TIME SELF-LEARNING ON MOTORS WITH LIMIT-SWITCH
PRELIMINARY NOTE: When using magnetic limit switches (such as on B-200 model), make sure that
the control unit is set on «magnetic limit switch» before learning:
MENU 104 - SELECT LIMIT SWITCH - “Magnetic”
1) Turn off the power supply, release the motor and place the door (or the barrier) manually at its mid run
2) Reset the mechanical lock
3) Select 9 - PROGRAMMING on the display, press OK and then one of the UP or DOWN buttons.
Now the gate will automatically execute a CLOSING-OPENING-CLOSING cycle
4) The self-learning is done
WORKING TIME SELF-LEARNING ON MOTORS WITHOUT LIMIT-SWITCH (NO LS)
PRELIMINARY NOTE: motors without limit-switch must have MECHANICAL STOPS IN OPENING AND
CLOSING set on the desired point of stop as in opening as in closing
Follow the points from 1 to 4 above shown as in the procedure for limit-switch motors
ATTENTION: If the motor starts in opening, remove and re-put power supply, select on the display
5-REVERSE MOTOR and through the UP and DOWN buttons select ON; if you have the Jolly3 programmer,
activate the motor exchange function and, only if present, limit-switch exchange function. If the motor starts
in closing and stops, remove the power supply and reverse the motor cables, then repeat the programming
procedure
ATTENTION: This procedure is potentially dangerous and should only be performed by qualified
personnel in safety conditions
The control unit is pre-set with DEFAULT settings. To start the control unit with the DEFAULT settings
just keep pressed the UP and DOWN buttons at the same time power supplying the control unit
till the display shows the message «INIT». The DEFAULT settings are shown in the Menues table
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English
33
FUNCTION LOGIC
AUTOMATIC LOGIC
A start impulse opens the gate. A second impluse during the opening will not be accepted.
A start impulse during closing reverses the movement.
NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will
be semi-automatic.
NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU
the item 7-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.
SECURITY LOGIC
A start impulse opens the gate. A second impulse during opening reverses the movement.
A start impulse during closing reverses the movement.
NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will
be semi-automatic.
NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU
the item 7-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.
STEP BY STEP TYPE 1 LOGIC
The start impulse follows the OPEN-STOP-CLOSE-STOP-OPEN logic.
NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will
be semi-automatic.
NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU
the item 7-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.
STEP BY STEP TYPE 2 LOGIC
The start impulse follows the OPEN-STOP-CLOSE -OPEN logic.
NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will
be semi-automatic.
NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU
the item 7-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.
DEAD MAN LOGIC
The gate opens as long as the START button of opening is pressed; releasing it the gate stops. The gate
closes as long as the button connected to the PEDESTRIAN START is pressed; releasing it the gate stops.
To execute complete opening and/or closing cycles the related pushbuttons must be constantly pressed.
2 PUSHBUTTONS LOGIC
One start opens, one pedestrian start closes. In opening the closing will not be accepted. In closing a start
command reopens, a pedestrian start command (closes) will be ignored.

34
UPDOWN
PRESS AT THE SAME TIME FOR 5 S TO ENTER OR TO EXIT THE SPECIAL MENU
SPECIAL MENU
MENU SP Default
SET
SPECIAL MENU FUNCTIONS TABLE USER 1 24V DG R1B
For entering into the special menu move on one of the menu and press the UP and DOWN
buttons at the same time for 5 s. For exiting the special menu press END or move on one of the
menu and press the UP and DOWN buttons at the same time for 5 s.
Description Set Value
30 100
30 100
30 100
30 100
30 100
10 100
10 100
10% (Fast intervention)
99% (Slow intervention)
Off (Intervention excluded)
10% (Fast intervention)
99% (Slow intervention)
Off (Intervention excluded)
- - - - -
Off
5 100
Off
5 100
17 - OPENING SPEED 1 *
18 - CLOSING SPEED 1 *
21 - OPENING SLOWDOWN
SPEED 1 *
22 - CLOSING SLOWDOWN
SPEED 1 *
25 - LEARNING SPEED *
28 - OPENING TORQ 1 *
29 - CLOSING TORQ 1 *
33 - OPENING SENSITIVITY
MOTOR1 *
34 - CLOSING SENSITIVITY
MOTOR1 *
57 - WORKING CURRENT
59 - OPENING
SLOWDOWN 1 *
60 - CLOSING
SLOWDOWN 1 *
10% (Fast intervention)
99% (Slow intervention)
Off (Intervention excluded)
37 - SLOWDOWN
SENSITIVITY
xxx.
xxx.
47 - ENCODER PAR.1 *
48 - ENCODER TOT.1 *
0 %
100%
63 - DECELERATION *
Setting from 30 to 100
Setting from 30 to 100
Setting from 30 to 100
Setting from 30 to 100
Setting from 30 to 100
Opening torq
Closing torq
Adjusts the intervention time
of the Encoder in opening
Disabled
Adjusts the intervention time
of the Encoder in closing
Disabled
Disabled
Adjusts the aperometric
sensitivity during slowdown
Shows the absorbed current
by the motor during the mo-
vement. The letter H at the
left of the current value indi-
cates the exceeding of the
set inversion threshold
Disabled
Setting from 5 to 100
Disabled
Setting from 5 to 100
Encoder impulses during operation
Encoder impulses stored
Adjusts the passage
between normal speed
and slowdown speed
30
30
* 50
* 50
* 80
* 80
* 40
* 40
* 50
* 60
* 60
30
On
32 - ENCODER
If ON it allows the
Encoder reading Off
0 %
100%
64 - ACCELERATION *
Acceleration ramp
Adjusts the motor start
Note: Menus 47 and 48 are present only if the encoder is ON
* 70%
* 50%
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English
35
73 - CLOSING TOLERANCE
MOTOR1
0 100
82 - MOTOR RELEASE
1 100
Off
Disabled
Setting from 1 to 100
Off
Adjusts the tolerance
between stop and obstacle
closing
0
MENU SP Default
SET Description Set Value
0 15 6 %
0 15 6 %
70 - OPENING POSITION
RECOVERY
71 - CLOSING POSITION
RECOVERY
Retrieves the inertia of the
motor in opening after Stop
or reversing
Retrieves the inertia of the
motor in closing after Stop
or reversing
0 100
Adjust the tolerance between
stop and obstacle opening
72 - OPENING TOLERANCE
MOTOR1 0
Off
Off
79 - ANTI INTRUSION Only closing
Only opening
Opening and closing
If you force the gate
manually, the control
unit starts the motor to
restore the state of the
gate before forcing
85 - PREFLASHING
86 - FLASHING LIGHT
87 - FLASHING LIGHT
AND TIMER
88 - COURTESY LIGHT
89 - TRAFFIC LIGHT
RESERVATION
90 - PEDESTRIAN OPENING
91 - PEDESTRIAN PAUSE
92 - TIMER
0.0 5.0
Only closing
Buzzer
Normal
Light
Always
Off
On
In cycle
1 240
Off
Off on
20 100
= Start
Off
Off
On photo2
On pedestrian entry
1 240
Pre-flashing only
active before closing
Pre-flashing time
Normal
Control lamp
Always ON
Buzzer
The flashing light remains
OFF with the active timer
and open gate
The flashing light remains
ON with active timer and
open gate
Disabled
Courtesy light setting
from 1s to 4 min
Courtesy light in cycle
Off
Normal
Off
Off
Off
30
= Start
Off
When setting this function
the pedestrian input will be
activated to work on the
auxiliary board SEM
(traffic light management)
Setting from 20 to 100
Pause in pedestrian opening
same as in total opening
Disabled
Setting from 1s to 4 min.
Transforms the selected
input in an input on
which to connect an
external clock

36
MENU SP Default
SET Description Set Value
Negative brake management
Negative Electrobrake
1 flash per sec. in opening
2 flashes per sec. in closing
Steady lit in Stop or Open
Gate open warning
light
Always AUX output always
power s u pplied
94 - 24V AUX
In cycle
In pause
Opening
Closing
AUX output power sup-
plied only during opening
AUX output power sup-
plied only during closing
AUX output power sup-
plied only during pause
AUX output active
only during cycle
Always
Fototest
In cycle and fototest
AUX output only during cycle
with fototest function active
AUX output for connection
of photocell TX to autotest
Positive brake management
Positive Electrobrake
95 - FOTOTEST
Photo1
Photo2
Photo1-2
Auto-test active only on Photo1
Auto-test active only on Photo2
Auto-test active on
Photo1 and Photo2
Photo1-2
97 - PHOTO1
Opening and closing
Closing
Stop and close
Close
Pause reload
Active in opening and closing
Photocell active in closing
The photocell gives a command
to close during opening, pause
and closing
The photocell charging
t h e p a u s i n g t i m e
The photocell stops in closing
and closes when released
Closing
Delay pause time
If the photocell is occupied
during opening, pause or
closing, the gate reopens
completely and closes without
observing the pause time
Shadow loop
Until occupied with open gate,
it prevent reclosing. The loop
function is OFF during closing
Shadow loop RP
Until occupied with open gate,
it prevent reclosing. Once
released, the gate repeats the
pause timebefore closing.
The loop function is OFF during
closing
Stop
The photocell is active
also before opening
Start 3s
Barrier Led Light
the output will be activated at
each Start impulse for 3 seconds
The 24Vaux output will pilot the
lights on the barrier so that, with
the beam closed the light is on,
with the beam opened the light is
switched off and with the moving
beam the light is blinking
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English
37
MENU SP Default
SET Description Set Value
98 - PHOTO2
Opening
Opening and closing
Closing
Stop and close
Close
Pause reload
Active in opening and closing
Photocell active in closing
The photocell gives a command
to close during opening, pause
and closing
The photocell charging
t h e p a u s i n g t i m e
The photocell stops in closing
and closes when released
Delay pause time
If the photocell is occupied
during opening, pause or
closing, the gate reopens
completely and closes without
observing the pause time
Shadow loop
Until occupied with open gate,
it prevent reclosing. The loop
function is OFF during closing
Shadow loop RP
Until occupied with open gate,
it prevent reclosing. Once
released, the gate repeats the
pause timebefore closing.
The loop function is OFF during
closing
Stop
The photocell is active
also before opening
Stop N.O.
(only for VERG barrier)
It modifies the PHOTO2 input
into a Normally Open stop button
100 - EDGE1
8K2
Edge is active and pro-
tected by a 8K2 resistor
Normal
99 - PHOTO OFF
IN CLOSING 0 50 0
Setting from 0 to 50
Normal N.C. contact
Normal
8K2 Double
Photo 1 10K
Photo 1 10K Double
Allows to connect two
edges protected by a 8K2
resistor
Edge works as a photocell
protected by a 10K resistor
Allows to connect two
photocells protected by a
10K resistor
104 - SELECT
LIMIT SWITCH *
Mechanical limit switch
Magnetic limit switch
Mechanical
Magnetic
Mechanical
102 - EDGE
DIRECTION
Opening and closing
Only in Closing
Only in Opening
Active in opening and closing
Active only in Closing
Active only in Opening
Opening
and
closing
Stop and Open
If the photocell is activated during
opening, the gate stops and con-
tinues to open when released.
The photocell is ignored in
closure

38
1 10
Shows last event
(See alarms table)
106 - DIAGNOSTICS
0 240000 0
100 240000 100000
107 - MAINTENANCE
CYCLES
108 - PERFORMED
CYCLES
Setting from 100 to
240000
See Note 3 below
Reports the executed
cycles. Keep pressed
OK to reset the cycles
112 - PASSWORD - - - -
Allows the entering of a
password blocking the
control unit parameters
modification
- - - -
When ON, if no mains
power and batteries
connected, the gate
will open fully and will
remain open until the
power returns. At this
point it will perform an
automatic reclosing
113 - EMERGENCY Off On
Off
Press OK to exit the special menu.
The special menu switches off automatically after 20 minutes
120 - BASIC MENU
MENU SP Default
SET Description Set Value
From 30% to 100% 80%
119 - DISPLAY WRITING
SPEED
Note 1: The * indicates that the default value or the menu may change depending on the selected motor
type.
Note 2: After initialization the parameters "motor type" and "limit switch type" remain son the value chosen in
the setup program.
Note 3: Display writing speed set on 30% keeps writing slow; Display writing speed set on 100% keeps
writing fast. Please note that speed does not change on JOLLY 3 display.
105 - MASTER-SLAVE
Master
Slave
Off
Off
For applications with two
motors in master-slave,
you can set the control
unit as slave
For applications with two
motors in master-slave, it
allows to set the control
unit as master
Disabled
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English
39
Initial system
Software Version
Programming example
DISPLAY INPUT STATUS
W h e n t h e
segment is ON
d u r i n g s e l f -
lea rnin g , the
input status is
closed or OFF
Start
pedestrian
Photocell 1
Photocell 2
Edge 1
MENU
SEA
SET
- - -
- -
- - -
Start
Stop
Limit
Switch
opening
motor 1
Limit
Switch
closing
motor 1
VERG
UP
OK
UP
UP
UP
DOWN
DOWN
DOWN
OK
OK
OK
DOWN
SCOR
JOINT
UP
U.001
MOTOR
LIMIT SWITCH
CLOSING
LIMIT SWITCH
OPENING
MENU
START
Description Description
EDGE
PHOTO1
PHOTO2
END
Start test
Safety edge
test
Photocell 1
test
Photocell 2
test
Opening
limit switch
test
Closing
limit switch
test
The contact must be a N.O. Contact . When activating the related
command on the display SET lights up, the input works.
If SET is always on, check the wirings.
The contact must be a N.C. Contact. When activating the related
command on the display SET lights up, the input works.
If SET is always on, make sure that the contact is a N.C. Contact
The contact must be a N.O. Contact. When activating the related
command on the display SET lights up, the input works.
If SET is always on, check the wirings.
The contact must be a N.C. Contact. When activating the related
command on the display SET lights up, the input works.
If SET is always on, make sure that the contact is a N.C. Contact
Ithe contact must be a N.C. Contact. When activating the related
command on the display SET lights up, the input works.
If SET is always on, make sure that the contact is a N.C. Contact
The contact must be a N.C. Contact. When activating the related
command on the display SET lights up, the input works.
If SET is always on, make sure that the contact is a N.C. Contact
Exit menu
OK
OK
MENU FUNCTION TABLE CHECK USER 1 24V DG R1B INPUTS
To access the Menu for input check keep pressed OK for about 5 seconds.
OK
0.0V
Batteries
Voltage
Level
Note: If the Stop, Photocell 1 and Photocell 2, Edge 1 contacts are not bridged in self-learning,
they will be deactivated and can be reactivated through this menu, without repeating times self-learning
The contact must be a N.C. Contact. When activating the related command on
the display SET lights up, the input works. If SET is always on, make sure that
the contact is a N.C. Contact. Menu active only on version with limit switches
Enabled
Enabled
Blocked
Blocked
Enabled
Blocked
Enabled
Blocked
Pedestrian
Start test
STOP OK
OK
START
PEDESTRIAN
OK
Enabled
Blocked
Enabled
Blocked
Stop test
Batteries charge level indicator
The contact must be a N.C. Contact. When activating the related command on
the display SET lights up, the input works. If SET is always on, make sure that
the contact is a N.C. Contact. Menu active only on version with limit switches
INPUT CHECK MENU
The settings of the control unit are made through the UP, DOWN and OK buttons. The UP and DOWN
buttons to scroll through the MENUS and SUBMENUS. By pressing OK you enter from MENU into
SUBMENU and confirm the choice. Moving in the 1-LANGUAGE menu pressing the UP and DOWN buttons
at the same time you access the SP MENU for special settings. Moving in the 1-LANGUAGE menu pressing
the OK button for 5 seconds, you enter the CHECK MENU, where you can check the operating status of all
inputs.

40
RADIO TRANSMITTER SELF LEARNING
WITH RECEIVER ON BOARD OF CONTROL UNIT
!
WARNING: Make the radio transmitters programming before you connect the antenna and insert
the receiver into the special CMR connector (if available) with turned off control unit. With RF UNI
and RF UNI PG module it will be possible to use both Coccinella Roll Plus transmitters and radio
transmitters with fixed code. The first memorized radio transmitter will determine the type of the
remaining radio transmitters. If the receiver is a Rolling Code, press twice the button of the radio
transmitter that you want to program to memorize the first TX. In the case of transmitters with fix code it is
necessary to press 1 time the button of the transmitter you want to program to store the first remote control
Notes:
- Enter radio transmitters learning only when the working cycle stops and the gate is closed.
- You can store max. 2 of the available 4 functions. If the control unit receives a code which was already
associated to another function it will be updated with the new function.
TABLE EXAMPLE
Transmitter
button
Memory
location
Serial
number Customer
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
MENU
SEA
SET
MENU
SEA
SET
MENU
SEA
SET
SET
START
PEDESTRIAN
START
EXTERNAL
MODULE
STOP
DELETE A
TRANSMITTER
0OK? OK
CLEAR
MEMORY OK
PRESS
BUTTON STORED
STORED
STORED
STORED
PRESS
BUTTON
PRESS
BUTTON
PRESS
BUTTON
If you want to program the
pedestrian start as second
channel
If you want to delete
a single transmitter
If you want to delete
the whole memory
If you want to program the
activation of the LIGHT
output as second channel
Press the
button of the
transmitter
to be stored
Press the
button of the
transmitter
to be stored
Press the
button of the
transmitter
to be stored
Select with
UP or DOWN
the memory
location
to be deleted
and press OK
Press the
button of the
transmitter
to be stored
If you do not want to execute the
cancellation, press UP or DOWN to
return to the 2-TRANSMITTER menu
Confirm the cancellation
If you want to program the
UNLOCH as second channel
MENU
SEA
SET
MENU
SEA
SET
UP
MENU
SEA
SET
UNLOCH STORED
PRESS
BUTTON
Press the
button of the
transmitter
to be stored
If you want to program the
STOP as second channel
OK
for 10 s.
MENU
SEA
SET
OK
TRANSMITTERS
OK
MENU
SEA
SET
If you want to exit the
2-TRANSMITTERS menu
END
MENU
SEA
SET
OK
UP
OK
OK
OK
OK
OK
OK
OK
Menu output
RF UNI 16 USERS Whitout memory
800 USERS With additional memory MEM
RF UNI PG 100 USERS Fixed code
800 USERS Roll Plus
RF UNI PG 800 UTENTI Fixed code
800 UTENTI Roll Plus
New model
Old Model
12 3 4
0
1
2
3
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

41
START - STOP - PEDESTRIAN START - ANTENNA - PHOTOCELL
START (N.O.) The START is connected between the clamps 2 and 3 of the CN 1 terminal.
An impulse given to this contact opens and closes the automation depending onthe selected logic it can be given by a key switch,
a keypad, etc. To connect the other devices refer to the related instructions leaflets. (ie. loop detectors and proximity switches).
Note1: In DEAD MAN logic it is necessary to keep pressed the Start for the opening of the automation.
Note2: In 2 BUTTONS logic this button performs the opening.
STOP (N.C.) The STOP is connected between the clamps 2 and 5 of the CN1 terminal .
The pressure on this button immediately stops the motor in any condition/position. A start command is needed to
re-start the movement. After a stop the motor always re-starts in closing.
Can be activated through on-board display or through the Jolly programmer. In both cases it’s a N.O. contact
which provoques the opening of the automation keeping it open until it is activated. When it’s released, the gate
attends the set pausing time and executes the reclosing. The TIMER command can be activated on the inputs
FOTO2, START PEDESTRIAN.
Note1: When activated on the pedestrian entry, the pedestrian will be disabled also on the radio transmitter.
Note2: In case of intervention of a security device during the timer (Stop, Ammeter, Edge), to restore the movement it will be
necessary to give a start impulse.
Note3: In case of no power supply with open gate and active Timer the control unit will restore its use, otherwise if during restore
of the power supply the TIMER is not activated it will be necessary to give a start impulse for the reclosing.
TIMER
PEDESTRIAN START (N.O.) The pedestrian start can be connected
between the clamps 2 and 4 of the CN1 terminal .
This input allows a partial opening the opening space can be set through the
on-board display or through the JOLLY device.
Note1: The contact for partial opening is a N.O. Contact (Normally open).
Note2:In 2 BUTTONS logic it is necessary to keep pressed the Start Ped. to re-close the automation.
Note3: In dead man logic this button executes the re-closing if you keep it pressed.
Note4: When closed during pause, the gate will reclose only after this input has been reopened.
TIMER activation: This input can be transformed into TIMER (See TIMER).
Photocell 1 and Photocell 2 Connections
+ = 24V (Accessories) max 750mA COM = 0V PH1 = Photocell contact 1
PH2 = Photocell contact 2
Note: Self-test: connect the TX to the AUX clamp and activate the Autotest function. The
photocell 1 default setting is FOTO CLOSE and the photocell 2 one is FOTO OPEN. The
photocell 2 can be set also as TIMER (see TIMER function).
Note3: On the 26-FOTOTEST menu you can also activate the self-test even on the single
photocell.
OPTIONS ON FOTO1 and FOTO2 adjustable on on- board display or with
JOLLY terminal.
FOTO CLOSE activation (“Closing”): if occupied, reverses the movement in closing,
during pause it prevent the closing.
Activation repeat pause (“Pause reload”): If occupied, during pause it recharges the
timer of pause. In closing it reverses the movement.
FOTO OPEN AND CLOSE activation (“Opening and closing”): If activated the photocell
blocks the movement as long as it’s busy, when released the opening continues.
FOTO PARK activation (“Stop and close”) : in opening it is not active; in pause are
activated it commands the closing when released, otherwise it’s not active; in closing it stops
the movement as long as it is busy, when released the closing continues.
FOTO STOP activation (“Stop”): When activated before the opening the photocell blocks
the automation as long as it is busy, during the opening it will be ignored. In closing the
intervention of the photocell causes the reopening.
Activation PHOTO CLOSE IMMEDIATELY (“Close”): The photocell stops the gate as
long as it is occupied in both opening and closing, when released it gives a closing command
(Closing one second after release of the photocell ).
“Delay pause time”activation: If the photocell is occupied during opening, pause
or closing, the gate reopens completely and closes without observing the pause time.
Antenna Common Start Start ped. Stop Common Photocell 1
CN1
1 2 3 4 5 6 7 8
Photocell 2
RX1
RX2
TX1
TX2
CN1
9 10 11 12 13
Common
24V (Accessories)
Options AUX 24V max 200mA can be set with
on-board Display or with Jolly device.
Through the Jolly programmer it is possible to chose when
having tension on the AUX output. The options are: “Always”,
“In cycle”, “Opening”, “Closing”, “In pause”, “Fototest” and
“In cycle and fototest”. When using control units with batteries
and/or solar panels, we recommend connecting the accesso-
ries which are not used when operator stands still (e.g. photocells) to a
AUX output, setting the option “In cycle”. With this setting you can save
energy by lowering power consumption in stand-by, increasing the
autonomy of the system.
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English
42
Flashing Lamp 24V (Accessories) 3W max. (Control lamp)
The Flashing Lamp can be connected between the 24V clamps
(Accessories) and FL (-) of CN 1. The Flashing lamp advises that the
automatic gate is moving with 1 flash/second in opening and 2 flashes /
second in closing. During pause it remains switched on. Through the
warning lamp it is also possible to identify alarms lied to the STOP,
PHOTOCELL 1, PHOTOCELL 2 and EDGE devices. Through the display
or the JOLLY 3 programmer it is possible to activate the pre-flashing
function and/or to modify the function of the warning lamp choosing
between fix flashing or control lamp.
The pre-flashing can be timed from 0 to 5 seconds
otherwise it is possible to set it before closing only
WARNING LAMP - SAFETY EDGE - 10K PHOTOCELL - BUZZER
IMPORTANT NOTE: INSTEAD OF THE FLASHING LAMP, YOU CAN ALSO CONNECT A BUZZER
REMEMBER TO SET THE 86-MENU ON «BUZZER»
24V FLASHING LAMP 3W MAX 12 and 13
Example of flashing lamp and edge
connections
Buzzer (24V ) Audible Alarm
Use an autoswinging buzzer 24V of 100 dB.
The buzzer will be switched on after two consecutive activations of the
entrapment protection.
To reset the allarm it is necessary to push the button STOP.
Anyway after 5 minutes the buzzer will stop to sound and the automation
stands still waiting for commands.
If Buzzer does not work, check the 86-FLASHING LIGHT menu is set on “Buzzer”
!
SAFETY EDGE 9 and 11
Between clamps 9 and 11 on the terminal CN1 it is possible to connect an active Safety Edge. When pressed, the
Safety Edge opens the contact causing a partial inversion of the movement both in opening and in closing. The
Safety Edge output can be set «only in closing», «only in opening» or both directions
Note1: Note1: Through the on-board display or the JOLLY 3 programmer it is possible to activate the balanced
edge 8K2, in this case the edge contact is controlled by a special resistance value revealing the eventual
involuntary short- circuit of the device. In case of imbalance of the device a special alarm will be shown on the on-
board dispaly or on the JOLLY programmer.
Note2: Self-test can be made also on a radio powered Edge (See Auto-test Menu)
24V BUZZER 12 and 13
10K PHOTOCELL or DOUBLE 10K PHOTOCELL 9 and 11
Between clamps 9 and 11 on the terminal CN1 it is also possible to connect
a 10K Photocell or two 10K Photocells . In this case it is necessary to set it
on menu 100 - EDGE as Photo10K (or Photo1 10K Double), then it will run
following settings on menu 97 - PHOTO 1.
Nota1: The use of a 10K Photocell allows to get further protection in case of
short-circuit on the cables.
Example of 10K Photocell and Buzzer
connections
9 10 11 12 13
Edge Edge
BROWN
BROWN
Common Common
CN1
24V (Accessories) 24V (Accessories)
BLUE
BLUE
WHITE
WHITE
GREY
GREY
9 10 11 12 13
WHITE
GREY
GREY
Example of two 10K Photocells
connections
10K Photocells
MENU
SEA
SET
100-EDGE 1
OK
MENU
SEA
SET
PHOTO 10K
.
OK
OK
MENU
SEA
SET
UP
OFF
Setting 10 K Photocell
MENU
SEA
SET
100-EDGE 1
OK
MENU
SEA
SET
PHOTO 10K
.
MENU
SEA
SET
UP
OFF
MENU
SEA
SET
100-EDGE 1
OK
MENU
SEA
SET
PHOTO 10K
.
MENU
SEA
SET
UP
OFF
MENU
SEA
SET
100-EDGE 1
OK
MENU
SEA
SET
PHOTO1 10K DOUBLE
.
MENU
SEA
SET
UP
OFF
Setting
10K Double Photocell
Edge Common
24V (Accessories)
FL(-)
9 10 11 12 13
CN1
Safety edge
10K
Photocell
CN1
9 10 11 12 13
Edge
BROWN
Common
FL(-)
24V (Accessories)
-
+
BUZZER
BLU
WHITE
GREY
E

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English
43
MAGLOCK 12V CONNECTIONS
DRAWING SHOWS HOW TO
EVENTUALLY CONNECT THE
MAGNETIC LOOP
Safety exit
loop 1
Loop1
Loop2
Loop3
Shadow
loop 2
Free exit
loop 3
10 11 12 13
1 2 3 4 5 6 7 8 9
CN1
12
7
6
8
6
3
6
Safety exit loop (loop 1)
Connecting scheme of
loop detector 1 reader
7 = Contact photocell 1 (N.C.)
6 = Common
Shadow loop (loop 2)
Connecting scheme of
loop detector 2 reader
8 = Contact photocell 2 (N.C.)
6 = Common
Note: Please set
98-PHOTOCELL2 - LOOP2
menu to “Shadow loop”
Free exit loop (loop 3)
Connecting scheme of loop
detector reader
3 = Contact start (n.o.)
6 = Common
C1 = CONTACT OPEN
C2 = CONTACT CLOSED
12 = 24 V
C = 0 V
SAFETY LOOP CONNECTIONS
6
Brown
Green
Pink
Yellow
Grey
NOTE:
For both MagLock
types it is
necessary to set
menu 94 - 24V AUX
on “negative brake
management” MagLock
COM
CN1 (11)
1 2 3 4 5 6 7
AUX
CN1 (10)
COM
NO NC
COM
12V DC
{
MagLock
COM
CN1
AUX
CN1 (24Vdc)
COM
NO
NC
COM
External power supply 12V / 24V DC
MagLock
Type 54020285
MagLock
Type 23105340
External
power supply
12V / 24V DC
-C2
C1
C
C2

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English
44
(BAT)
+
-
+
-
GND PSOL BAT 28VGND
CN1
+
-
S
+
GND
Solar Panel
Batteries
12V 12V
= charge 200mA
~
~
= charge 360mA
= charge 800mA
~
Code 23101105
Code 23101104
E SUN
E SUN Q
S 28VGND
CN1
+
GND
Solar Panel
PSOL GND
+ Bat- Bat
= charge 200mA
~
~
= charge 360mA
= charge 800mA
~
USER 1
24V DG
R1B
CNQ
+
-
+
-
Batteries
12V 12V
Note: To connect
the User 1 24V
DG R1B control
unit with quick
c o n n e c t a b l e
charger to an old
battery charger,
you must use the
C NQ a da p te r
cable
IMPORTANT: To connect the batteries, always use the battery charger
CONNECTION OF BATTERIES TO BATTERY CHARGER CARD
28V Battery charger
Positive battery
Negative battery charger
Battery current (mA) Battery (Ah)
Insert two 12V batteries connected in series
800
360
200
12 or 16
7
2
Specifications of optional batteries: 24V Pb
CN7
EXTERNAL RECEIVER
Example: Connection
of a radio receiver
For the connection of
the receiver refer to the
relative instructions
manual
Common Common
24V (Accessories)
1 2 3 4 5 6 7 8 9 10 11 12 13
CN1
Start
Start ped.
+
-

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
English
45
MASTER-SLAVE FUNCTION
To set an installation with two motors in MASTER-SLAVE function it is recommended to do as follows:
1) Set the two motors as if they were two independent installations, make sure that the individual motor
works properly and that the limit switches (when present) are read properly.
2) Once sure of the correct functioning connect the control unit MASTER to the control unit SLAVE through
the special clamp (Code SEA 23001220).
3) Now set the control unit, which has to manage the commands and motor 1 (photocell, keyswitch, STOP,
safety edge etc.) as MASTER and the other one which will move motor 2 as SLAVE.
4) Follow up the selflearning of the times of the MASTER control unit.
Note 1: The master and slave settings on the control unit are present in the special menu selecting
105-MASTER-SLAVE.
Note 2: All these operations can also be managed through the JOLLY 3 programmer)
Note 3: On the SLAVE it is possible to set the following functions only: torque, speed, motor type, slowdown
speed, acceleration, deceleration, position recovery, AUX and motor inversion
All other parameters will be set only by the MASTER control unit
Insert on CN4
of the Master
control unit
Insert on CN4
of the Slave
control unit
Note: respect the polarity of the cables
2
Note: It is recommended to use a two twisted pairs shielded cable with less than 0.5 mm section
MASTER SLAVE
SIGB COM SIGA SIGB COM SIGA
M1 M1
CN4
This configuration is usable in the case of two opposite sliding gates.
In this configuration, all devices (photocells, key switch, edges, etc.) must be connected on the MASTER unit
which will also control the movement of the motor linked to the SLAVE unit.