Seal Line BLACK CANYON DRY PACK I 65L User manual

LIMITED LIFETIME
WARRANTY
For limited warranty information, please go to
seallinegear.com/warranty
FOR REPAIR OR
WARRANTY SERVICE
Please contact our product service center:
U.S. 1-800-531-9531
CANADA 1-888-801-5335
ONLINE seallinegear.com/warranty
#34-047 | EN
DRY
PACK
OWNERS
MANUAL
BLACK CANYON™DRY PACK | 65L / 115L
The Black CanyonTM Dry Pack is a versatile large-
capacity waterproof pack with a suspension system
designed for more comfortable load hauling on canoe/
raft trips, canyoneering adventures and travel
expeditions. These instructions will show you how to
properly seal your pack, attach/detach your harness &
waist belt, and take care of your pack.
DRY PACK CARE & USE
To substantially increase the life of dry packs, follow
these guidelines: After each use, the pack should be
cleaned and air dried; To clean, wash with a soapy brush
and rinse; Store pack once completely dry, inside and
out; When packing, pad items with hard, sharp corners
to minimize wear on the fabric; Keep all insect repellents
and solvents from making direct contact with dry packs.
If contact occurs, wash the pack thoroughly.
NOTICE
No roll-down closure pack from any
manufacturer is 100% waterproof when submerged. This
pack is not suitable for protecting items such as optical,
electrical or photographic equipment, as submersion
or impact may do permanent damage. For such equip-
ment, hard cases with O-ring seals are recommended to
protect against impact damage and long-term submer-
sion. SealLine®Dry Packs are intended to protect your
equipment and belongings from rain, splash, and spray.
They are not intended for submerged use. SEALLINE®
©2019 Cascade Designs, Inc.
4000 First Ave. S.
Seattle, WA 98134 U.S.A.
1-800-531-9531
seallinegear.com
BLACK
CANYON™

CLOSE & SEAL PACK
1
1. FOLD To properly close and seal pack, first ensure both
black sealing strips are wrinkle-free. Fold the top over
toward sealing strips, line up strips, and press together.
FOLD HERE
burp!
3x
2
2. BURP Hold sealing strips firmly together and push down on
the pack to ‘burp’ out trapped air. Fold and roll tightly at least
twice until black strips are no longer visible.
3
3. CONNECT Connect both side buckles and cinch down
to compress. Place both top straps over fold, buckle,
and cinch down for additional compression.

ATTACH/ DETACH & ADJUST SHOULDER HARNESS
NOTE: The pack comes with the shoulder harness and waist belt attached. To detach
for travel or dry bag use, and to adjust torso length, see instructions below.
DETACH HARNESS
ATTACH & ADJUST HARNESS
1 2 34
1. Lay the pack down with the back
panel facing up. Unthread the webbing
from the load lifter straps atop
shoulder straps.
FIG 1
2. Unthread the red tab from the plastic
loop at the base of the yellow cord.
3. Unthread yellow cord and plastic loop
through orange strip (angling tip for
more clearance).
4. Unthread long black tongue until the
harness is completely detached.
FIG 2
1 2 34
1. Insert the long black tongue into
the sleeve between the pack and
hard plastic. Lift up the end to expose
the orange strip.
2. Pull the yellow cord and plastic
loop through the orange strip (angling
tip for more clearance) to expose
the plastic loop on the other side of
the orange strip.
3. Thread the red tab through the plastic
loop at the base of the yellow cord,
anchoring the hook and loop together.
Your shoulder harness is now attached.
4. Thread webbing through the load
lifter straps atop shoulder straps and
waist belt. Carefully lift pack onto
back and adjust straps for optimal
carrying comfort.
FIG 2
FIG 1

1
1
2
2
3
ATTACH/ DETACH WAIST BELT
1. Detach webbing from side adjustment buckles.
1. Slide waist belt buckle beneath the lumbar panel and pull the waist belt webbing
through until the waist belt is centered. (PRO TIP: line up stitching on each side of
waist belt to confirm it’s centered). Press down on the lumbar panel to re-attach
the hook and loop fasteners beneath the panel.
NOTE: Pack comes with the waist belt attached. To detach
it for travel or dry bag use, see instructions below.
DETACH WAIST BELT
2. Reach under lumbar panel to separate and detach the
hook and loop fasteners beneath the panel. (PRO TIP:
Slide a narrow piece of cardboard or plastic in between
panels to prevent the hook and loop fasteners from
accidentally re-attaching).
2. Ensure webbing is pulled all the way through and reattach webbing to side
adjustment buckles.
3. Slide waist belt out from beneath the lumbar panel.
ATTACH WAIST BELT