HUALIAN M-PE Series User manual

PE SHRINK PACKING MACHINE
BS5530M-PE ＆BS5540M-PE
OPERATION MANUAL
中 国 ●华联机械有限公司

I. USE:
Shrink packing machine is one of the advanced packaging ways in the international
market at present. It adopts shrink film to products or being packed articles, and
then to heat the shrink packing material & tightening products or being packed
articles, so that the appearance of the articles is shown fully, so that the articles can
be put well on display and which may also increase the their beauty and value.
Besides, the packed articles can be sealed, damp proof, dustproof and protect
themselves from outside shock and thus have the better functions. Especially for
packing glassware, which can prevent household utensils from scattering when they
are broken? In addition, this way can decrease the torn and stolen possibility of the
products. As the shrink film shrinks, some pressure can be created to tighten a
group of packed articles together and trays so this product can be used widely for
shrinking all kinds of shrink packing material.
II. FUNCTION & FEATURE:
PE shrink packing machine manufactured by our company is the latest automatic
continuous shrink packing equipment both at home at present. It adopts quartz
far-infrared capsule to heat for saving electricity 9save over 15%).Shrink packing
machine adopts frequency con troll motor, whose speed can be adjusted within
wide range, and the maximum load bearing can reach to 40kg. The stove inside
adopts fully closedown hot wind circulating equipment to get perfect sealing effect.
This machine has a nice appearance an with easy maintenance, can applicable to
all the shrinking package of all kinds of PVC, POF & PP ETC. shrinking films,
specially suitable for PE shrink film’s packing.
III. SPECIFICATION
Model Voltage Power Weight
loading
Heat tunnel
size(mm) Dimension(mm) Conveying speed Weight
BS5530M-PE 380 16.8 40 550×300 2500×750×1300 0~10 210
BS5540M-PE 380 18 40 550×400 2500×750×1400 0~10 240

IV. CONTROL PANEL:
1. Intelligent temperature regulator 2. Heating switch 3. Conveying switch
4. Electronic speed regulator 5. Hot wind switch II 6. master control switch
7. Heating master switch 8. cooling switch
V. TEMPERATURE & TIME FOR SHRINK FILM:
Term
Film Name Thickness (mm) Heating(S)
Shrinking room
temperature (℃)
Polyvinyl chloride PVC 0.02~0.06 5~10 110~130
Polypropylene PP 0.02~0.04 6~12 130~170
Polyethylene PE 0.03~0.10 20~30 170~200
Polyethylene PE 0.12~0.20 30~60 180~220
VI. OPERATION PROCEDURES & NOTICE:
1. This machine is three phases with four pieces of power wires (380V), and thus in
addition to connecting to the three pieces of live wires, you should connect it to the
zero line as well.
2. Closing the master controlling switch (5) and master heating switch (7).
3. Closing the master controlling switch (5) and adjusting the conveying button (4)
4. Pressing the heating switch (2), the machine starts to heat. The shrinking
temperature of PE film is generally set at 180~200℃, if you want to set the
temperature, please firstly press SET key, then press UP or DOWN key, and at last
press SET key after your confirmation.
5. During the operation, if there are too many rumples, please decrease the conveying
speed of increase the heating temperature Whereas, if the shrinking film broken,
then please increase the conveying speed of decrease the heating temperature.

6. After rinsing package, firstly, please shut off the heating switch, and let the
conveying motor and fan working for another 20 minutes of so, then shut off the other
power switch, master heating switch and master controlling switch.
7. The diameter of the inputting wire for this machine should be more than 6mm, and
do not put your hand into the machine in case there’s an electric shock.
8. The machine should be put flatly at the ground, or the mesh-belt would be aberrant;
after three months using, please check the aging of the electricity wire, and
exchange it if it’s necessary.
VII. MALFUNCTION & TROUBLESHOOTING:
If there’s a malfunction, firstly please have a check whether the inputting voltage
is normal and also it is in the right wire connection.
1. There’s no heating phenomenon in the shrinking room.
a) The temperature regulator has seized up: maintain or exchange it.
b) AC contactor has been damaged: exchange it.
c) The wire connectors have been aging and lead to turnoff: reconnecting them.
d) The heating tube has been damaged: exchange it.
2. The conveying motor doesn’t work:
a) The motor switch has seized up: exchange it.
b) Speed regulator has been damaged: exchange it.
c) The motor has been burnt due to high temperature: exchange it.
3. Hot wind motor doesn’t work:
a) The fan has been damaged: exchange it.
b) Hot wind switch has been damaged: exchange it.
c) The fan leaf has been blocked: reset the machine after solving this problem.
VIII. SPARE PARTS OF INNER CLRCULATING SHRIN PACKING
MACHINE
Model Quantity
BS5530M-PE BS5540M-PE
Machine body 1set
Truckle 4pieces
Underlay foots 4 pieces
Note: 1. A few mechanisms have slightly different for the above- mentioned models and we
don’t to describe here
2. Customizing models will all used this operation manual, and if there’s any changes for its

specification, we won’t we won’t describe here.
7
40
26
25
5
1
16
27
33
28
24
2 3 4 6 11
15
14
13
17
38
19
20
29
8 9
23
30
32
39
21
22
31
18
PE-M broken down diagram for the shrink packing machine spare
BS5530M-PE & BS5540M-PE
10 12
41
37 36 35 34

Spare parts list for M-PE shrink packing machine
NO Name S
1 Chain I 08B 398 nodes with pin GB 14212-93
2 Locating collar φ27× φ21×10
3 Mesh-belt Wide495
4 Roller
5 End lid Inner φ20
6 Driven shaft φ20×587
7 Driven chain wheel P=12.70,Z=14, inner φ32
8 Bearing 6804Z
9 Bale spring In φ17.5×1 GB 894.1-86
10
11 Heating light tube with coolant φ16×1500，2.3KW
12 Heating tube fix bar
13 Bearing 6004-2RS GB/T 276-94
14 Locating collar φ27×φ21×7.5
15 Chain wheel P=9.525,Z=18, φ20
16 Driving chain wheel P=12.70,Z=14, φ20
17 Driving shaft φ20×600
18 Locating collar φ27× φ21×14
19 Underlay foots M16
20 Lion universal castor 3 inches
21 Chain II 06B-1-144 GB 14212-93
22 Chain wheel P=9.525,Z=18,φ15
23 Reduce guiding motor YYJT90-3,90W,1300r/min 1:40
24 Wiring base TB1505，600V，15A
25 Temperature regulator SWD-7137P，0~400℃，220VAC
26 Switch 321B/N82，16A，250VAC
27 Potentiometer WX110（010），5K6
28 Control switch DZ47-63（C16）-2P
29 Heating switch DZ47-63（C63）-3P
30 Capacitor CBB60，5uF
31 AC electronic speed regulator SS ，8A，220V
32 AC citatory CJX2-5011，220V
33 Wiring base TC604，60A-4P
34 Fan
35 Fan leaf
36
37
38
39 Heat insulating bar 550×800
40 Fan leaf M12
41 Fan YY7112,250W,220V,50r/min

380V for earth connect
123456
13 14 J
M
M
Hot wind
Potentiometer
Heating tubeHeating tubeHeating tube
Heating master k1
AC contactor J
Power master switch
Conveying motor
ELECTRIC THEORY DIAGRAM
0
12
43
78
65