SealerSales FS-205 User manual

IMPULSE SEALER
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
MODELS:
FS-100
FS-200/205
/
FS-300
/
305
FS-400/405
FS-500/505
F
S
-2
00C/
2
05C
S
00C/ 05C
FS-300/305C

1. PARTS IDENTIFICATION 10. TROUBLESHOOTING
MALFUNCTIONS REASONS SUGGESTIONS
No sealing
Power lamp is off Disconnected plug Power cord is broken
Transformer is broken
Check or change the plug
Replace or repair the cord
Replace the transformer
No sealing
Power lamp is on
Sealing lamp is on
Heater (heating element) is
broken
Sprin
g
hook our mountin
g
Replace the heater
Clean or tighten spring
hook connection
Sealing
lamp
is
on
gg
spring is loose or in poor
contact
Terminals of the heating
element are in poor
contact
Clean the terminals and
adjust if needed
No sealing
Power lam
p
is on Microswitch is activated Defective microswitch Adjust the microswitch
lever
p
Sealing lamp is off Adjust the microswitch
position
Replace the microswitch
Teflon cloth burn Timer malfunction
Prolonged heating time Replace timer or relay Decrease the timer
setting
2. CONNECTION DIAGRAM
Heating wire breaks Worn Teflon adhesive Replace the Teflon
adhesive
Seal is wrinkled Heating timer is set too
high
Cooling time is not enough
Lower the timer setting
Continue pressing the
upper lever for 1-2
seconds after the light
goes off
goes
off
Imperfect seal Worn Teflon cloth
Worn silicone rubber Replace Teflon cloth Replace silicone rubber
Broken seal Prolonged sealing time Decrease timer setting
Non-full-weld seal Sealing time is too short Increase sealing time
Seal sticking Dirty Teflon cloth
Dirty sealing bar Clean the Teflon cover Clean the silicone rubber
sealing bar

The machine does not use a power switch. Plug the AC
5. OPERATION 6. GETTING STARTED
No warm-up time needed.
cord into the power source. Set the timer knob according
to the thickness of the materials to be sealed. The higher
the number on the dial, the longer the sealing time. Put
one plastic bag on the sealing platform, and then push
down the handle. The electronic circuit controls the heat
time automaticall
y,
the li
g
ht turns off
(
to cut off the
p
ower
Always start with the lowest setting #1.
Increase slowly until you get a satisfactory seal.
Once the correct setting of the timer is set, the sealer will
provide a consistent air and water proof seal every time.
y, g ( p
automatically). After 1-2 seconds, release the handle. The
perfect seal is complete.
Should the seal appear damaged, most likely, the timer on
the setting was too high. Adjust the knob to a lower timer
setting.
7. TIPS FOR SUCCESSFUL SEALING
Always keep the sealing platform clean. Avoid the
oxidation of the residual on the platform which will reduce
A non-tight seal is caused by sealing time that is too low.
Adjust the knob to a higher timer setting.
Should the plastic bag stick to the handle rubber, cooling
time needs to be longer. Keep the handle down for a short
time after the light turns off
oxidation
of
the
residual
on
the
platform
which
will
reduce
the life of the heating element and the teflon.
Do not use water to clean the sealing platform.
Should the bottom teflon cloth wear out, it will cause a
short circuit and damage the heating element. Each
time you replace the heating element or the top teflon
Slide the knife to cut off the rest of the bag. (Only for FS-
200C/205C and FS-300/FS-305C)
time
you
replace
the
heating
element
or
the
top
teflon
,
check the bottom teflon adhesive and replace if worn.
Only use original equipment replacement wires and parts.
A worn silicon handle rubber will influence the sealing
effect. After a long period of usage, it should be checked.
After the timer knob has been set, the heat time duration
will remain the same for each usage. It is unnecessary to
make further adjustments.

It is okay to leave the AC cord plugged into the power
Model FS-100/200/300/400/505 FS-200C/300C
FS-205/305/405/505 FS-205C/305C
Heating Element
2pcs
2pcs
8. SPARE PARTS
It
is
okay
to
leave
the
AC
cord
plugged
into
the
power
source. No power is used unless the handle is pressed
down.
Heating
Element
2pcs
2pcs
Teflon Cover 2pcs 2pcs
Blade -- 1pc

9. SPECIFICATIONS
Model FS-100 FS-200/200C FS-300/300C
Voltage
110
110
110
Voltage
110
110
110
Impulse Power (watts) 132 245 400
Max. Seal Length (mm) 100 200 300
Seal Width (mm) 2 2 3/2
Heat Time (sec) 0.2-1.3 0.2-1.3 0.2-1.3
Weight (lbs) 5 7/9 11/12
Model FS-400 FS-500
Voltage 110 110
Impulse Power (watts) 440 755
Max. Seal Length (mm) 400 500
Seal Width (mm)
3
3
Seal
Width
(mm)
3
3
Heat Time (sec) 0.2-1.3 0.2-1.3
Weight (lbs) 15 18
Model FS-205/205C FS-305/305C
3. PURPOSE
Perfect for sealing PE and PP bags to package various
kind of
p
roducts in the food or industrial industr
y
Voltage 110 110
Impulse Power (watts) 315 425
Max. Seal Length (mm) 200 300
Seal Width (mm) 5 5
Heat Time (sec) 0.2-1.3 0.2-1.3
Weight (lbs) 9/11 13/14
py
4. CHARACTERISTICS
CONVENIENT AND COMPACT
Model FS-405 FS-505
Voltage 110 110
Impulse Power (watts) 600 800
Max. Seal Length (mm) 400 500
ENERGY SAVER
–
UTLIZES ENERGY ONLY WHEN
SEALING
PRECISION ELECTRONIC CONTROL CIRCUIT
EASY TO OPERATE
Seal Width (mm) 5-Jan 5
Heat Time (sec) 0.2-1.3 0.2-1.3
Weight (lbs) 17 20
Specifications subject to change by manufacturer.