Sealey 57M.V2 User manual

Manufactured to German GS/TUV standards. Fine rolled threading and precision made thrust
bearing for long life and smooth operation. Curved base plate allows for radial movement when
lifting vehicle.
Model No. 57M.V2 58M
Maximum height ......330mm ..........375mm
Minimum height ...... 85mm ..........100mm
Closed length ........365mm ..........405mm
Capacity . . . . . . . . . . . .1000kg ..........1500kg
INSTRUCTIONS FOR:
SCISSOR JACK
MODEL NO’s: 57M.V2 & 58M
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
3Ensure that the jack is in good working order. Take action for immediate repair or
replacement of damaged parts. Use genuine parts only. The use of unauthorised
parts may be dangerous and will invalidate the warranty.
3Locate the jack in a suitable, well lit work area.
3Keep work area clean and tidy and free from unrelated materials.
3Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
3Ensure the vehicle handbrake is engaged, engine/motor is switched off and
transmission is in 1st or reverse gear. (or park for automatics)
3Ensure minimum distance of 0.5m between vehicle and static objects such as doors,
walls, etc., to allow for vehicle tilting.
3Only place jack under those lifting points recommended by the vehicle manufacturer
(see vehicle handbook).
3Check the lifting point is stable and centred on the jack saddle.
3Ensure there are no passengers in the vehicle.
3Place wedges under wheels of vehicle.
3Ensure all non-essential persons keep a safe distance whilst the jack is in use.
3Use suitable capacity axle stands under the vehicle before proceeding with any task.
3Ensure there are no persons or obstructions beneath the vehicle before lowering.
pDANGER: Use the jack for lifting only, NOT for supporting the lifted load.
7DO NOT operate the jack if damaged.
7DO NOT work under the vehicle until axle stands have been correctly positioned.
7DO NOT allow untrained persons to operate the jack.
7DO NOT use the jack for purposes other than that for which it is designed.
7DO NOT exceed the rated capacity of the jack.
7DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous
substances.
7DO NOT allow the vehicle to move while supported by the jack.
3When not in use store jack, fully lowered, in a safe, dry, childproof area.
pWARNING! It is very dangerous to go under a vehicle which is supported by a jack
even if additional supports are used. DO NOT go under a vehicle unless it is
supported by adequately rated axle stands.
IMPORTANT! Ensure that you can see the saddle and jacking point throughout the
jacking operation in case there is any relative movement.
2. INTRODUCTION & SPECIFICATIONS
1. SAFETY INSTRUCTIONS
Original Language Version 57M.V2, 58M Issue: 4 - 14/10/09

3.1. General jacking.
pWARNING! Before lifting ensure Section 1 safety instructions are strictly followed.
3.1.1. Prepare the vehicle as mentioned in the safety instructions ensuring the ground on which
the jack is to stand is level and solid (not tarmacadam).
3.1.2. Position the jack saddle under the vehicle manufacturer’s recommended lifting point.
3.2. Jacking the vehicle.
3.2.1. Turn the handle clockwise to bring the jack saddle into contact with the recommended
lifting point.
3.2.2. Ensure the jack is vertical before continuing to turn the handle clockwise and raising
the vehicle to the required working height. Turn the handle slowly and evenly to ensure no
sudden movements of the vehicle.
3.3. Lowering the vehicle
3.3.1. Turn the handle anti-clockwise and lower the vehicle. Lower slowly to ensure no sudden
movements of the vehicle.
pSAFETY WARNING! Always lower in a slow and controlled manner and ensure there
are no persons or obstacles beneath the vehicle, or in the path of it’s descent.
Lifting Operations and Lifting Equipment Regulations (LOLER) 1998. This jack, depending on
use, may fall within the scope of LOLER. It is the owner’s responsibility to determine whether or
not it does and, if so, to comply with any applicable requirements in LOLER, for having the jack
thoroughly examined.
IMPORTANT: Only fully qualified personnel should attempt maintenance or repair.
4.1. Keep the jack clean and lubricate all moving parts with acid free oil on a regular basis.
4.2. Before each use check for broken, cracked, bent, or loose parts, or any visible
damage to welds, saddle, frame and all parts including nuts, bolts, pins and other
fasteners. If any suspect item is found remove jack from service and take necessary
action to remedy the problem. DO NOT use the jack if believed to have been
subjected to abnormal load or shock. Inspect and take appropriate action.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE JACK.
3. OPERATING INSTRUCTIONS
4. MAINTENANCE
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version 57M.V2, 58M Issue: 4 - 14/10/09