Sealey AK9623EV User manual

INSTRUCTIONS FOR
DIGITAL VERNIER CALIPER 0-300MM/0-12”
MODEL NO: AK9623EV
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools and
equipment.
8DO NOT use if damaged.
9Maintain calliper in good and clean condition for best performance.
9Keep the work area clean, uncluttered and ensure there is adequate lighting.
9Keep children and unauthorised persons away from the work area.
8DO NOT use the calliper for any purpose other than for which it is designed.
8DO NOT get calliper wet or use in damp or wet locations, or areas where there is condensation. Keep calliper clean and dry using a
dry cotton cloth only.
8DO NOT dip or submerge the calliper in any type of liquid.
8DO NOT expose calliper to bright sunlight or dust.
8DO NOT disassemble. The calliper must be checked by qualied service personnel only.
8DO NOT apply any voltage to the calliper i.e. with an electric marker pen.
9 The calliper is a precision instrument, treat with care, avoid using force and do not subject to knocks or shocks.
9Use in reasonably constant temperature conditions of approximately 20°C.
9When not in use, turn off and store gauge in a safe, dry, childproof location.
2. INTRODUCTION
Hardened and tempered stainless steel digital calliper with satin nish. 11mm High gures in LCD display for ease of reading. Metric and
Imperial calibration with conversion between the two. Zero setting control allows for comparative measurement. Supplied in carry-case.
3. SPECIFICATION
Model no: ..............................................................AK9623EV
Range: ........................................................ 0-300mm (0-12”)
Resolution: .................................................0.01mm (0.0005”)
Accuracy<100mm: .....................................±0.02mm (0.001”)
Accuracy>100mm: .....................................±0.04mm (0.002”)
Refer to
instruction
manual
1234
5
6
7 8
9
10
11
1 Internal measure
2 Metric/Imperial selector
3 Locking screw
4 ABS/0 switch
5 LCD display
6 External measure
7 On/off control
8 Zero control
9 Battery cover
10 Depth measure
11 Step measure
AK9623EV | Issue 2(L) 10/07/17
Original Language Version
© Jack Sealey Limited

4. OPERATION
4.1. Ensure all measuring surfaces are clean and then turn on calliper by pressing on/off control. Wait at least one second before use.
4.2. Loosen locking screw and close the calliper; if read-out does not show zero when in closed position, reset by pressing zero control.
4.3. Select inch or mm units, as required, with the metric/imperial selector. Check that display shows the required units.
4.4. Measurements will now be shown directly on the LCD display.
4.5. A new zero may be obtained, at any open position of the calliper, by pressing the zero control.
4.6. A second measurement that then also needs to be added to the rst one can be obtained by pressing the ABS/0 switch after obtaining
the rst measurement (display will show ‘INC’), then move the callipers to measure the second one. After noting this, press the ABS/0
switch again and the display will show the total of both measurements.
5. BATTERY FITTING
5.1. A ashing display indicates that the battery is exhausted - replace as follows:
5.2. Switch off and then remove battery cover (9) by rmly sliding towards the right.
5.3. Remove exhausted battery and t replacement with positive side uppermost (g.1). Ret battery cover.
5.4. Dispose of old battery in a safe and approved manner. DO NOT burn.
5.5. If the display fails to alter when the slide is moved, remove the battery - wait at least 30 seconds and then ret the battery.
AK9623EV | Issue 2(L) 10/07/17
Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Fig.1