Sealey CX105.V3 User manual

CX105.V3, CX108.V3 Issue:1 - 11/09/17
Original Language Version
© Jack Sealey Limited
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
Refer to instruction
manual
1. SAFETY
INSTRUCTIONS FOR
2/3 LEVEL HEAVY DUTY WORKSHOP TROLLEY
MODEL NO’S: CX105.V3 & CX108.V3
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this trolley.
9Always load evenly with the centre of gravity of the load as near centre of the trolley as possible.
8DO NOT overload the trolley - see specifications.
9Use the trolley in a suitable work area.
9Keep the work area clean, uncluttered and ensure there is adequate lighting.
9Keep the trolley clean and tidy in accordance with good workshop practice.
8DO NOT use the trolley for any purpose other than that for which it is designed.
8DO NOT stand on the trolley, use it as a ladder or allow others to ride on the trolley.
9Use the wheel locks to prevent the trolley from inadvertently moving.
8DO NOT leave unattended, especially when loaded, unless the wheels are locked, chocked or the trolley otherwise secured.
8DO NOT use trolley on uneven ground and do not run over curbs or steps - use a ramp.
8DO NOT use trolley if any part is significantly damaged, paying particular attention to the wheels.
9Keep children and unauthorised persons away from the work area.
2. INTRODUCTION
Ideal for regularly used workshop items such as body repair kits, power tools and bulky equipment too big for a tool chest. Strong build quality and
extra large castors also make this an excellent dismantling trolley for smaller vehicle components.
3. SPECIFICATION
Model No: ...........................................................CX105.V3....................................................... CX108.V3
Overall Size (W x D x H):....................................840 x 405 x 810mm ........................840 x 405 x 810mm
Shelf Size (W x D x H): .......................................790 x 400 x 80mm ............................790 x 400 x 80mm
Capacity: .............................................................100kg (50kg/level)............................. 150kg (50kg/level)
4. ASSEMBLY
g.1
Fig.1
4.1. Attach posts to trays.
4.1.1. Lay one tray (the one with the four sets of castor holes on the
bottom) on the floor and attach posts to the outside corners
of the tray using 32 x M6 short bolt and nut sets.

g.2
Fig.2
This step is NOT applicable for CX109HV go to g.3
4.2. Attach the other tray to the inside top of the posts using 32 x M6
short bolt and nut sets.
4.2.1. Put the trolley on its side and work on two posts at a time, for ease
of assembly.
CX105.V3, CX108.V3 Issue:1 - 11/09/17
Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.