Sealey CP20VGBS User manual

20V 15L CORDLESS GARDEN BACKPACK
SPRAYER - BODY ONLY
MODEL NO: CP20VGBS
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLYAND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
CP20VGBS Issue 2 (2,3) 18/02/22
Original Language Version
© Jack Sealey Limited
Refer to
instructions Wear eye
protection Wear protective
gloves Wear protective
clothing Wear a mask
1. SAFETY
9Only use the sprayer for it’s intended purpose.
9Familiarise yourself with the applications, limitations and potential hazards of this product.
9Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
9Always inspect and prepare the sprayer before use according to the instructions contained in this manual.
8DO NOT use the sprayer if it is damaged, altered, modied, in poor condition, leaking uids or has any missing components.
8DO NOT alter the sprayer in any way.
8DO NOT use the sprayer for spraying ammable materials.
WARNING! Ensure you are fully aware of all the potential hazards of the material being sprayed. Read and understand the
warnings and instructions on the container or the supplied manufacturers information.
8DO NOT spray any material where the hazards are not known.
9 Ensure that the spray containers cannot easily be knocked over during lling.
9 Mark uid containers with hazard labels to show it’s chemical contents, even if it’s water.
9 It is highly recommended that individual uid containers should be used only for one type of specic agent.
9 Keep any uid containers in a well ventilated, lockable store.
9Keep children and unauthorised persons away from the working area, especially during the spraying operation.
9Maintain the sprayer in good condition and keep clean to maintain safest performance.
9 Ensure that the uid containers cannot easily be knocked over when transferring unused uid back into it.
9 Keep the sprayer turned o󰀨.
9 Keep the uid tank lid rmly closed to prevent any spillage.
8DO NOT turn on the power until ready to spray.
9Be aware of wind direction whilst spraying. Spray from upwind to downwind to prevent direct chemical contact with your body.
8DO NOT spray when the wind speed is in access of 4mph.
8DO NOT over apply pesticide. Only apply at the manufacturer’s recommended rate. Excess pesticide can be hazardous to
humans, wild life, damage plants and contaminate soil and water sources.
8DO NOT eat, drink, rub your eyes, or touch any part of your bare skin whilst handling uids or when spraying. If chemical(s)
come into contact with skin, immediately wash thoroughly with soap and water.
8DO NOT spray near open ames or other sources of heat.
8DO NOT smoke or use an open ame anywhere near the sprayer or around stored uids.
9 Maintain correct balance and footing. Ensure the oor is not slippery and wear non-slip shoes.
8DO NOT operate the sprayer when you are tired or under the inuence of alcohol, drugs or intoxicating medication.
9 Always clean up any spills immediately as per uid manufactures instructions.
8DO NOT spray at people, animals or protected insect species.
9 Select the appropriate chemical which o󰀨ers the best solution to your pest or weed problem.
WARNING! When mixing chemicals, thoroughly read and understand the manufacturers instructions.
WARNING! Inappropriately mixed chemicals may harm people and damage crops or plants.
9Always mix chemicals prior to adding the solution to the sprayers tank reservoir.
9Ensure the sprayers tank reservoir is full prior to use. Operating the sprayer with an empty tank may damage the pump.
WARNING! If the spraying stops running, or an abnormal sound is emitted immediately switch o󰀨 and remove the battery.
WARNING! Wear appropriate PPE (Personal Protective Equipment). To avoid inhalation and/or skin or eye contact with the
chemical wear, protective goggles, protective mask, rubber gloves, long sleeved waterproof jacket, long trousers and Wellington
boots.
WARNING! Remove battery cartridge when performing maintenance or making adjustments.
9Operators, whose physical, sensory or mental capabilities prevents them from safely using the sprayer, must be under the
supervision of a person who has a thorough knowledge and experience of the sprayer and the appropriate regulations.
8DO NOT allow children or untrained persons to operate the sprayer.
WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may occur. It must be understood that common sense and caution are factors
which cannot be built into this product, but must be applied by the operator.
Wear respiratory
protection

2. INTRODUCTION
Cordless 20V backpack garden sprayer. This sprayer does not require manual pressing which makes it easy and practical to use. Supplied
with 3 di󰀨erent nozzles to meet di󰀨erent needs and an auto cut-o󰀨 function. This backpack sprayer can be used for sterilization, disinfection,
weed killing as well as watering owers and spraying water. It has an added lter to prevent larger particles clogging the machine. With
strong durable back straps to ensure comfort when worn. 15L water tank with a lance holder clip. Spraying lance including hose is 2.53m.
Requires compatible 20V battery and mains charger, sold separately.
3. SPECIFICATION
Model No: ........................................................... CP20VGBS
Consumable parts:.................................................................
Battery (not included):............................................................
2Ah ......................................................................CP20VBP2
4Ah ......................................................................CP20VBP4
6Ah ......................................................................CP20VBP6
Mains Charger (not included):...............................CP20VMC
Dimensions (W x D x H):............315mm x 320mm x 580 mm
Hose length:...................................................................1.7m
Maximum ow rate: .................................................. 1.3L/min
Maximum pressure:......................................................1.6bar
Noise power:.............................................................83dB(A)
Noise pressure:.........................................................72dB(A)
Tank capacity:..................................................................15L
Vibration:................................................................0.494m/s²
Vibration uncertainty:.................................................1.5m/s²
4. CONTENTS
5. ASSEMBLY
5.1. INSTALLING THE BATTERY CARTRIDGE
5.1.1. Open the battery cover door by releasing the sprung catch (g 1).
5.1.2. Align the tongue on the battery cartridge with the groove in the battery housing and slide into place.
5.1.3. Insert all the way until the battery cartridge is locked into position with an audible click.
8DO NOT try and insert the battery cartridge forcibly.
5.1.4. Firmly close the battery cover (g 3).
5.2. REMOVING THE BATTERY CARTRIDGE
5.2.1. Open the battery cover door by releasing the sprung catch (g 1).
5.2.2. Push the battery cartridge latch button, then slide and remove the battery (g 2).
5.2.3. Firmly close the battery cover (g 3).
WARNING! Ensure that the sprayer is switched o󰀨 and the battery cartridge is removed prior to undertaking any work on the
sprayer.
Original Language Version
© Jack Sealey Limited
ITEM DESCRIPTION
1 Nozzle
2Spray pipe
3Fluid tank lid
4Spray pipe holder
5Fluid tank reservoir
6Trigger lever
7Control handle
8Water pipe
9Power switch
10 Battery cartridge cover
11 Bolt
12 Back pad
13 Back strap
14 Nozzle selection
CP20VGBS Issue 2 (2,3) 18/02/22

5.3. CONNECTING THE WATER PIPE
WARNING! Ensure the supplied joint washers are tted, check prior to assembly.
NOTE: Securely attach the water pipe to ensure that there are no leaks.
5.3.1. Insert the end of the water pipe centrally into the opening of the control handle (g 4).
5.3.2. Firmly push the hose as far as it will go (g 4).
5.3.3. Slide the xing nut down the hose and onto the threaded end of the control handle.
5.3.4. Fully tighten by turning the xing nut clockwise (g 5).
5.4. DISCONNECTING THE WATER PIPE
5.4.1. To disconnect the water pipe follow section 5.3 but in reverse.
5.5. CONNECTING THE SPRAY PIPE
WARNING! Ensure the supplied joint washers are tted, check prior to assembly.
NOTE: Securely attach the spray pipe to ensure that there are no leaks.
5.5.1. Locate the end of the spray pipe centrally onto the remaining threaded end of the control handle (g 6).
5.5.2. Fully tighten by turning the end nut clockwise (g 7).
5.6. DISCONNECTING THE SPRAY PIPE
5.6.1. To disconnect the spray pipe follow section 5.5 but in reverse.
5.7. CONNECTING THE NOZZLE
5.7.1. Select nozzle type to suit application.
5.7.2. Locate the end of the nozzle centrally onto the threaded end of the spray pipe (g 8).
5.7.3. Fully tighten by turning the end nut clockwise (g 8).
5.8. DISCONNECTING THE NOZZLE
5.8.1. To disconnect the nozzle follow section 5.7 but in reverse.
5.9. REMOVAL OF BACK PAD
5.9.1. Unscrew the four xing bolts with a T30 star head screw bit and place in a secure location (g 9).
5.9.2. Remove the back pad and place in a dry, secure location.
5.10. ATTACHING THE BACK PAD
5.10.1. To attach the back pad follow section 5.9 but in reverse.
5.10.2. Fully tighten the xing bolts.
g.4 g.5
g.6 g.7 g.8
g.9
g.10
g.11
Fig.12
Original Language Version
© Jack Sealey Limited
g.1 g.2 g.3
CP20VGBS Issue 2 (2,3) 18/02/22

5.11. ATTACHING THE BACK STRAP
5.11.1. Feed the back strap through the xed link pin (g 10).
5.11.2. Feed the back strap through the upper slot of the plastic buckle (g 11), and then through the lower slot of the plastic buckle and
pull tight (g 12).
5.12. ATTACHING THE BOTTOM CLIP
5.12.1. Hook each bottom clip onto it’s corresponding tab at the base of the sprayer (g 13).
5.13. BACK STRAP ADJUSTMENT
9Adjust the back strap so that the sprayer is in a comfortable position and as close as possible to the body.
5.13.1. To lengthen the strap, lift up the buckle (g 14), and pull the belt through from the side connected to the sprayer.
5.13.2. To shorten the strap, lift up the buckle (g 14), and pull the belt through on the free side.
WARNING! Ensure that the back strap is securely attached to the sprayer.
5.14. ATTACHING THE SPRAY PIPE HOLDER
5.14.1. Fully slide the pipe holder over the pipe holder boss (g 15).
5.14.2. Insert the spray pipe into the pipe holder (g 15).
5.14.3. To remove the pipe holder lift it up and o󰀨 the pipe holder boss and place in a secure location.
6. OPERATION
NOTE: Ensure all Safety Instructions in Section 1 are read and understood and carried out before use and save the instructions and
warnings for future reference.
6.1. POWER SWITCH
WARNING! Ensure that the sprayer power switch is in the OFF position prior to installing the battery cartridge.
WARNING! To prevent sudden spraying ensure that the trigger lever is in the stop position and the power switch is in the OFF
position.
6.1.1. To turn the sprayer on, press down the I (ON) on the power switch (g 16).
6.1.2. To turn the sprayer o󰀨, press down the O (OFF) on the power switch (g 16).
6.2. OPERATING THE SPRAYER
6.2.1. To operate the sprayer depress the trigger lever to spray, then release the trigger lever to stop (g 17).
6.2.2. For continuous spraying depress the trigger lever and while it’s depressed push forward to lock on.
6.2.3. To lock o󰀨 pull the trigger lever back and release (g 17).
6.3. SPRAYING
6.3.1. When using the sprayer rmly grip the control handle.
6.3.2. Once spraying is complete release the trigger lever to stop and turn the power switch to OFF.
6.4. SPRAY ADJUSTMENT
6.4.1. To adjust the intensity of the spraying turn the adjustment button clockwise to increase and anticlockwise to decrease (g 18).
8DO NOT operate the sprayer with an empty tank. Turn OFF immediately.
8DO NOT use the sprayer with the battery cover open or with the back pad removed.
WARNING! Prolonged continuous use of the sprayer will drain the battery and may cause damage to the pump. Switch OFF the
sprayer whenever possible.
WARNING! If the sprayer starts to make abnormal noises and/or the spray splutters this indicates that the tank is empty.
Switch OFF immediately.
6.5. FILLING THE TANK
WARNING! Ensure that the sprayer power switch is in the OFF position prior to lling the tank.
6.5.1. When lling the tank ensure the tank lter is tted into the top of the tank (g 23).
6.5.2. Fill the tank with the required volume utilising the level indicators on the tank.
6.5.3. Firmly tighten the tank lid after lling.
NOTE: Maximum volume of tank = 15L.
WARNING! When lling the tank wear appropriate PPE.
WARNING! DO NOT ll tank in a poorly ventilated area.
7. MIXING CHEMICALS
WARNING! Ensure that all chemical mixtures are thoroughly dissolved prior to use.
WARNING! Take extreme care when handling chemicals. Wear appropriate PPE. Wash thoroughly away any chemicals that comes
into contact with bare skin.
WARNING! Chemicals are harmful. Always read and fully understand the manufacturers instructions before use.
Original Language Version
© Jack Sealey Limited
Fig.14
Fig.13 Fig.15
Fig.16 Fig.17 Fig.18
CP20VGBS Issue 2 (2,3) 18/02/22

8. MAINTENANCE
8.1. Have the sprayer serviced by a qualied repair person using only genuine replacement parts. This will ensure that the
safety of the sprayer is maintained.
8DO NOT attempt any maintenance or repairs that are not included in this manual.
8DO NOT use solvents to clean sprayer.
8.2. AFTER USE MAINTENANCE
8.2.1. Dispose of any residual liquid from the sprayer tank, by returning it back to it’s original container. Clean up any spills immediately
as per uid manufactures instructions.
8.2.2. Wash out the tank with clean water and after cleaning, pour the water into a suitable container.
8.2.3. Rell the tank with clean water and run the sprayer for up to 3 minutes, removing any residue from the pump, water hose, control
handle, spray pipe and nozzle into a suitable container. Ensure all water has been removed from the system.
8.2.4. Wipe away any remaining moisture with a dry cloth.
NOTE: Dispose of any contaminated water properly according to local regulations.
8.3. WATER ABSORPTION STRAINER CLEANING
WARNING! Ensure that the tank has been washed out and is free from any chemicals.
8.3.1. Unscrew and remove the tank lid and then the tank strainer.
NOTE: The water absorption strainer is located at the bottom of the tank.
8.3.2. Locate the water absorption strainer (fig 18) and carefully remove the strainer from the water pipe (fig 19).
8.3.3. Remove the top cap and clear any debris from the inside of the strainer (fig 20).
8.3.4. Replace the top cap and reattach the strainer to the water hose.
8.3.5. Refit the tank strainer and then the tank lid.
NOTE: The water absorption strainer prevents debris from entering the pump. Periodically clean the water absorption strainer to
maintain optimal performance.
8.4. CONTROL HANDLE STRAINER CLEANING
8.4.1. Fully unscrew the nut on the control handle (g 21) and detach the water pipe.
8.4.2. Remove the lter and remove any debris from the inside of the strainer (fig 22).
8.4.3. Replace the strainer and reattach the water pipe and fully tighten nut on the control handle.
NOTE: The control handle prevents debris from entering the spray hose. Periodically clean the control handle to maintain optimal
performance.
8.5. TANK STRAINER CLEANING
8.5.1. Unscrew and remove the tank lid.
8.5.2. Remove the tank strainer and clear any debris from the inside of the strainer (fig 23).
8.5.3. Refit the tank strainer and then the tank lid.
8.5.4. NOTE: The tank strainer prevents debris from entering the tank. Periodically clean the tank strainer to maintain optimal performance.
9. STORAGE
9.1. Wash out the sprayer as section 8.1 and ensure that the sprayer is completely free from moisture.
9.2. Store the sprayer in a child free, safe, clean, dry indoor location that is away from direct sunlight, has good ventilation and does not
freeze.
WARNING! Frozen liquids that remain in the sprayer may cause breakdown or damage to the pump during operation.
Fig.18
Fig.19 Fig.20
Fig.21 Fig.22
Fig.23
Original Language Version
© Jack Sealey Limited CP20VGBS Issue 2 (2,3) 18/02/22