Sealey HT107LED.V2 User manual

INSTRUCTIONS FOR
HEAD TORCH 5W CREE XPG LED WITH ADJUSTABLE
FOCUS & BRIGHTNESS 3 X AA CELL
MODEL NO: HT107LED.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. General
8DO NOT shine directly into your, another person’s or an animal’s eyes.
8DO NOT allow children to use the torch.
8DO NOT use the torch if you suspect that the battery or the torch casing is damaged.
8DO NOT leave batteries in a discharged state. Before storage remove batteries.
1.2. Battery Safety
WARNING! To reduce the risk of burns or re:
8DO NOT attempt to open the batteries.
8DO NOT crush, puncture, short contacts or dispose of in re or water.
8DO NOT expose to temperatures above 60°C (140°).
9Replace only with the batteries designed for this product.
9Recycle or dispose of used batteries as stipulated by local regulation.
9If the electrolyte in the batteries gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with
cool water and seek immediate medical attention.
2. INTRODUCTION
Hands free 5W CREE XPG spotlight with adjustable inclination to a direct light as required. Dimmer switch allows brightness to be adjusted
from 20% to 100%. Illumination type can be changed from spotlight to wide angle beam. Main light and rear red warning light can be switched
between on, off and ash function. Adjustable headband and foam brow for added comfort.
3. SPECIFICATION
Model No:.......................................................HT107LED.V2
LED Qty: ....................................................... 5W CREE XPG
Lumen output: .............................................................. 300lm
Battery: ................................................. 3 x AA (not included)
Weight:........................................................................... 240g
HT107LED.V2 | Issue 1 13/02/18
Original Language Version
© Jack Sealey Limited
Refer to
Instructions
Fig.1

4. OPERATION
4.1. Remove battery box twist cap (anticlockwise to open).
4.2. Insert 3 x AA batteries into compartment. Orientation diagram for batteries is inside shown inside battery box, replace cap.
4.3. Front lamp: Press on/off switch once for on, twice for ashing and third time to turn off.
4.4. Rear lamp: Press switch on side of battery box, once for on, twice for ash and third time for off.
4.5. Dimmer switch: Lever on top of battery box adjust for brightness.
4.6. Adjust beam using lever on front lens.
5. MAINTENANCE
5.1. Keep the torch clean by wiping with a damp cloth.
5.2. Remove batteries if not being used for a long period of time.
5.3. Store torch and batteries in a dry childproof area.
HT107LED.V2 | Issue 1 13/02/18
Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
BATTERY REMOVAL SEE 4.1
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.