SEASIDE CASUAL FURNITURE ENVIRO WOOD Traditional Picnic Table User manual

1
Tools Required:
Large Phillip's Head Screwdriver
1/2 Socket or Wrench
Hammer
(43) Traditional Picnic Table rev. A
WOODENVIRO
SEASIDE CASUAL FURNITURE
Hardware:
(28) 3-1/2” Truss 5/16” Bolts
(27) 4-1/2” Carriage 5/16” Bolts
(55) Nuts
(55) Flat Washers
(2) Table Slats with 3 holes (Aluminum Reinforced)
(2) Table Slats with 5 holes (Aluminum Reinforced)
(1) Center Table Slat with Umbrella hole (Aluminum
Reinforced)
(4) Legs
(1) Table Center Cleat with 2 holes
(2) Table End Cleats with 4 holes
Assembly Instructions
Step One: Set Up
READ ENTIRE INSTRUCTIONS BEFORE BEGINNING! Carefully remove contents
from box. Make sure that all parts and hardware are included.
Place All Table Slats face down with Aluminum facing up
on a flat clean surface. Follow the following list for place-
ment.
1st Slat (Far Left)= Table Slat with holes #1,#6,#11
2nd Slat (Middle Left)= Table Slat with holes #2,#7,#12
3rd Slat (Middle)= Center Table Slat with holes #3,#8,#13
4th Slat (Middle Right)= Table Slat with holes #4,#9,#14
5th Slat (Far Right)= Table Slat with holes #5,#10,#15
(Right Picture)
Step Two: Table Slat Placement
WARRANTY QUESTIONS OR COMMENTS PLEASE CALL TOLL FREE AT 1-800-809-3114
Parts List
(4) Seat Slats with 2 holes (Aluminum
Reinforced)
(4) Seat Cleats
(2) Angle Braces
(2) Seat Supports
Box 1: Box 2:
Instruction Revision: B
11 12 13 14 15
6 7 8 9 10
1 2 3 4 5

2
Step Three: Carriage Bolt Placement
Step Four: Table End & Center Cleats Attachment
Insert (19) 4-1/2” Carriage 5/16” Bolts into all Table Slat
End and Center Holes. Tap bolts with a hammer to set
square into the End and Center Holes (Right picture)
Place End and Center Cleat to Table Slat Carriage Bolts
by taping them into place on all Carriage Bolts with a
hammer and align cleats with numbers on slats. Attach
Cleats using flat washers, nuts and finger tighten (Left
Picture). Do not tighten at this time.
Step Six: Seat Support Attachment
Step Five: Leg Attachment
Place Leg along the inside of the End Cleat with the Leg
angled to the outside of the Table Top, while aligning
(2) pre-drilled holes. Attach using (2) 3-1/2” Truss
5/16” Bolts (Right Picture). Finger tighten using flat
washers and nuts. Do not tighten at this time. Repeat
process for all four legs.
Place Seat Support along inside of legs, while aligning
pre-drilled holes. Holes in Seat Supports must align with
holes in the Table center Cleat for aligning and attach-
ing the Angle Braces. Attach using (4) 3-1/2” Truss
5/16” Bolts. Finger tighten using flat washers and nuts
(Left Picture). Do not tighten at this time. Repeat proc-
ess on other side.

3
Tighten all connections. Do not over tighten!!! Over tightening of hardware can cause
damage to the item.
Step Eleven: Tightening of Hardware
Step Seven: Angle Brace Attachment
Step Eight: Placing Table to Standing Position
Place (2)Angle Braces along Seat Supports to the Table
Center Cleat while aligning pre-drilled holes. Attach us-
ing (4) 3-1/2” Truss 5/16” Bolts. Finger tighten using flat
washers and nuts. Do not tighten at this time. (Right pic-
ture)
Place Table to Standing Position on to its legs. This will require two people.
Step Ten: Seat Slat Attachment
Step Nine: Seat Cleats Attachment
Place (4) Seat Cleats along inside of Seat Supports,
while aligning pre-drilled holes. Attach using (8) 3-1/2”
Truss 5/16” Bolts. Finger tighten using flat washers and
nuts (Left Picture). Do not tighten at this time.
Place Seat Slats on top of Seat Supports and Seat Cleats
aligning pre-drilled holes, with Aluminum side facing
down. Attach using (8) 4-1/2” Carriage 5/16” Bolts.
This may require using a hammer to tap the Carriage
bolts in to pre-drilled holes. Finger tighten using flat
washers and nuts. Do not tighten at this time.