Sebo Airbelt E User manual

OWNER’S MANUAL
For Household Use Only

Technical Details 2
How To Contact SEBO 2
Important Safety Instructions 3
Special AIRBELT E Product Features 4
AIRBELT E1 Kombi & E2 Turbo Features 4
AIRBELT E3 Premium Features 5
Optional Attachments, Accessories, Bags and Filters 5
Standard Features of All SEBO Vacuums 6
Identification of Parts 7
Standard Attachments 7
Brushes and Heads 7
Assembly 7
Operating Instructions 8
Starting the Machine 8
Suction Control 8
Operating the Machine 8
Additional Operating Instructions for E3 Premium with Power Head 9
Starting the Machine and Suction Control 9
Operating the Machine 9
Using the Telescopic Tube, Hose & Attachments 10
Use and aintenance of Brushes and Heads 10
The Parquet Brush 10
The Kombi Nozzle 10
The Turbo Nozzle 10
Vacuum aintenance 11
Changing the Filter Bag 11
Changing the Pre-motor Filter 11
Changing the Exhaust Microfilter 11
Changing the AIRBELT 12
Clog Removal 13
Clogs in the Head or Brush 13
Clogs in the Telescopic Tube 13
Clogs in the Hose 13
Clogs in Entrance to Filter Bag 13
Trouble-Shooting Guide 14
AIRBELT E1 Kombi & E2 Turbo Schematic and Part Numbers 15
AIRBELT E3 Premium Schematic and Part Numbers 16
2
Vacuum motor 1200 watts
Filter bag capacity .8 gallons
Body weight 11.4 lbs
Motor protection Thermal cut-out
Cord length 25 feet
Range 37 feet
Technical details may be subject to change.
ABLE OF CON EN S
ECHNICAL DE AILS
To contact SEBO in the United States of America:
SEBO America, LLC
Telephone: [phone]
Fax: [phone]
Website: www.sebo.us
To contact SEBO in Canada:
Floor Care Equipment, Ltd.
Telephone: [phone]
Fax: [phone]
Website: www.sebocanada.ca
HOW O CON AC SEBO
For Warranty coverage information please refer to your Warranty Card included with your SEBO vacuum cleaner.

IMPOR AN SAFE Y INS RUC IONS
READ ALL INSTRUCTIONS BEFORE USING THIS ACHINE
3
1. Do not leave vacuum while plugged in. Unplug from
outlet when not in use and before servicing.
2. Do not use outdoors or on wet surfaces.
3. Do not use near small children or pets. Do not allow to be
used as a toy. Use of this product by children should
always be supervised by an adult.
4. Use only as described in this manual. Use only
manufacturer-recommended attachments.
5. Do not use with a damaged cord or plug. If vacuum is not
working as it should, has been dropped, damaged, left
outdoors, or dropped into water, take it to a SEBO service
center.
6. Do not pull or carry by cord, use cord as a handle, close a
door on cord, or pull cord around sharp edges or corners.
Do not run vacuum over cord. Keep cord away from heated
surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the
plug – not the cord.
8. Do not use outlets above counters to plug in vacuum –
damage to items in the surrounding area could occur.
9. Always carry the vacuum over steps and sills.
10. Do not handle plug or vacuum handle with wet hands.
11. Do not put any object into vacuum openings. Do not use
machine with any openings blocked. Keep openings free
of lint, hair, and anything that may reduce air flow.
12. Do not re-use filter bags or wash the filters.
13. Do not remove any screws from vacuum.
14. Do not vacuum up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
15. Do not use vacuum without filter bag and/or filters in place.
16. Turn off all machine controls before unplugging.
17. Use extra care when cleaning on stairs.
18. Do not use machine to vacuum up flammable or
combustible liquids such as gasoline or use in areas
where they may be present.
19. Machines can cause a fire when operated near flammable
vapors or materials. Do not operate this vacuum near
flammable fluids, dust or vapors.
20. Maintenance and repairs must be done by authorized
personnel.
21. Use only original SEBO replacement parts.
22. Do not use vacuum as a step.
23. If vacuum is used on plush carpet or carpet with thick
padding, do not leave machine standing in one place with
machine turned on.
24. While the vacuum is in use, the power cord should be
unwound from the cable reel at least two thirds of its length.
Hold plug when rewinding onto the cord reel. Do not allow
plug to whip while rewinding.
25. Keep hair, loose clothing, fingers, and all parts of body away
from vacuum openings and moving parts. Do not place
fingers or other body parts under vacuum unless it is
unplugged.
26. Do not place the power head over rug or carpet edges.
27. The vacuum has a manual reset thermal protector. The
protector is reset by switching off the vacuum. The thermal
protector needs some time to cool down after switching off!
Check the vacuum for air blockages or mechanical failures
before switching on.
28. Store the vacuum in a dry place at room temperature. When
the vacuum is not in use, you should rewind the cord onto
the cord reel
29. The E3 hose contains electrical wires. Do not use if
damaged, cut, or punctured. Avoid picking up sharp objects.
30. Always unplug vacuum before connecting or disconnecting
either hose or power head.
31. Use a SEBO power head only in combination with a SEBO
vacuum cleaner.
32. Do not connect power head to a malfunctioning or damaged
vacuum.
When using an electrical appliance, basic precautions must always be followed.
To reduce the risk of electric shock, this vacuum cleaner has a polarized plug; one blade is wider than
the other. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any
way. Connect only to the outlet type specified on the serial number plate underneath the machine.
SAVE THESE INSTRUCTIONS.
WARNING: To reduce the risk of fire, electric shock, or injury:
!

SEBO AIRBEL E PRODUC FEA URES
4
Bag Full or Clog Indicator & Auto Shut Off –
The warning indicator will show orange and
the machine will automatically shut off
when it senses a full bag, a clog in the air-
flow pathway, or an excessively dirty micro
filter.
If the vacuum’s airflow pathway
becomes restricted due to a full bag or the existence of a clog, the
warning indicator located on the top of the canister will show
orange. If the user ignores this warning, the suction motor will
heat up due to the lack of cooling provided by the airflow. Once the
motor reaches a certain temperature it will shut off to protect
itself from damage. The user should turn the switch off, unplug
the machine and immediately insert a new bag or remove the clog
(to remove a clog, refer to the Clog Removal section on page 13).
After approximately 30 minutes, the motor will have cooled and
the vacuum can be restarted. If the airflow is still restricted, the
indicator will again show orange and the machine will shut off.
This feature prevents damage to the motor due to overheating.
Shock Absorber Provides Furniture and
Wall Protection – The patented “AIRBELT”
bumper that surrounds the E canisters acts
as a protective barrier. The soft foam
bumper with its durable cover protects fur-
niture, walls and the vacuum itself from
damage during use. The bumper also dif-
fuses exhaust air, which contributes to its ultra-quiet perform-
ance.
Large Operating Range – A 37-foot operating range saves time
because it minimizes the number of electrical outlets needed
during use.
uick-release Connections – The AIRBELT E models allow for
quick and convenient connection of telescopic tubes, power
brush heads, accessory cleaning heads and on-board tools.
Comfortable Ergonomic Handle – The AIRBELT handles are
ergonomically designed and positioned to reduce wrist and
arm fatigue. For extra comfort, an additional swivel is built into
the handle-to-hose connection.
Mid-sized Canister Vacuum – The AIRBELT
E models are considered mid-size canister
vacuums, which means they are smaller,
more compact machines that offer three
full-size on-board tools and a large filter
bag with a capacity of .8 gallons. The large
capacity filter bag is economical because
fewer bag changes are needed. An indicator
window turns orange when the filter bag
needs to be replaced, and closing its built-
in hygiene cap prevents dust from escaping
during bag removal and disposal.
Three Protective, Rubber-coated Wheels,
mounted on steel axles – The superb rub-
ber-coated castor-wheels glide easily and
gently over all floor types, providing excep-
tional maneuverability and protection of
floor surfaces.
Flat-to-the-floor 3-1/2” Profile – A low cleaning-head profile
makes reaching under furniture and beds easy!
The SEBO AIRBELT E1 Kombi and E2 Turbo are straight-
suction vacuums. As a result, they differ from the AIRBELT E3
Premium in the following two ways:
Variable Power Control on Canister Body –
Because the AIRBELT E1 Kombi and E2
Turbo do not have an electrified hose and
telescopic tube, the variable power control
switch is located on the canister body, not
the handle.
Can Not Use a Power Brush – The AIRBELT E1 Kombi and E2
Turbo do not have an electrified telescopic tube and hose;
therefore, they do not accommodate an electrified power head.
Instead, the E1 Kombi model comes standard with a Kombi
Nozzle for rugs and carpets and the E2 Turbo comes standard
with a Turbo Nozzle, an air-driven brush head for cleaning rugs
and carpet and a Parquet Brush for cleaning hard floors.
Turbo Nozzle Parquet Brush
AIRBEL E1 Kombi and E2 urbo
Kombi Nozzle
The E1 Kombi Arctic White comes standard with the
Kombi Nozzle.
The E2 Turbo Dark Blue comes standard with the
Turbo Nozzle and the Parquet brush.
Dusting Brush
Crevice Nozzle
Upholstery Nozzle
Convenient Parking and Storage Aids – After the work is done,
the suction hose with telescopic tube and parquet brush, turbo
head or Kombi Nozzle can be firmly stored on the canister’s
underside or backside housing.
Three Full-size On-board Tools – The vacuum comes standard
with a crevice tool, dusting brush and upholstery nozzle. The
dusting brush is mounted on the telescopic tube, and the
crevice and upholstery nozzles are on the canister. Many
optional accessories are also available.

5
Designed for All Floor Surfaces. AIRBELT E3 Premium:
The AIRBELT E3 has an electrified hose and telescopic tube
designed to accommodate the commercial-quality ET-1 power
head. The ET-1 power head is designed to provide thorough
brushing for optimal cleaning of carpets.
Both Carpet and Hard Floor Cleaning – With a power brush to
clean carpets and a parquet brush to clean hard floors, the
AIRBELT E3 provides all the flexibility needed to care for a vari-
ety of floor surfaces. The parquet brush comes standard.
High-quality Telescopic Tube and Hose – On the E3, the power
cord is built inside the telescopic tube and suction hose. This
eliminates unsightly external wires and enables unobstructed
and convenient handle height adjustment.
Variable Power Control on Handle – The
vacuum’s suction power can be adjusted
from 0 to 1,200 watts by a slider switch con-
veniently located on the handle.
Powerful Vacuum Motors Provide Excellent Cleaning – The
canister suction motor is 1,200 watts, and the power head
motor is 175 watts (ET-1), for a total of 1,375 watts.
AIRBEL E3 Premium
The SEBO ET-1 (12” wide, 10 1⁄2” cleaning
width) – This power head delivers cleaning
flexibility because its brush action aggres-
sively cleans carpeting, and the brush may
be switched off to clean hard floors and
delicate rugs. The steering ability of the
swivel neck helps to easily clean around obstacles, and its L-
shaped head provides maneuverability around furniture and
under cabinets. It also has brush height and brush wear warn-
ing lights.
Brush Obstruction Light & Auto Shut Off –
If an obstruction becomes jammed in the
brush roller, a red brush-warning light will
quickly flash, the brush roller will immedi-
ately stop spinning and the vacuum will
shut off.
The user should turn the power
switch off, unplug the machine, and immedi-
ately remove the obstruction. If the user restarts the machine
without removing the obstruction, the power head will again shut
off and the red light will flash.
This prevents the belt from
breaking and protects the motor and carpet from damage.
Incorrect Height Setting or Brush
Deterioration Light – To ensure optimum
cleaning at all times, a red brush-warning
light will illuminate, to indicate when the
brush height is set too high for effective
cleaning or when the brush roller should be
replaced due to excessive wear.
CLOSE
In addition to the standard on-board tools, a variety of optional
attachments are available. The nine-foot extension hose
(extends suction hoses) and the 20-inch extension tube are very
popular because they create useful tools for cleaning stairs and
out-of-reach areas. These two items are sold separately or as
part of multiple item attachment kits. Another popular attach-
ment is the hand held turbo brush for removing pet hair from
upholstery.
20-inch Extension Tube
Part #1084 S
9-foot Extension Hose
Part #1495AM
E Filter Bags
Part #8300AM
SEBO filter bags can be purchased in boxes of eight and filters
are sold separately. Also, bags and filters can be purchased
together in model-specific kits called “Service Boxes.” SEBO
bags, filters and accessories are reasonably priced and widely
available.
To create a fresh scent while vacuuming, “SEBO FRESH” is
available. To use, deposit a scented stick in the filter bag.
SEBO FRESH
Part #0496AM
OP IONAL A ACHMEN S, ACCESSORIES, BAGS & FIL ERS
Kombi Nozzle
Part #7260 S
Flat Upholstery
Nozzle
Part #1090 S
Hand-held Turbo
Brush
Part #6179 S
Radiator Brush
Part #1496 S
Premium Parquet Nozzle
Part #7200 S
Turbo Nozzle
Part #6780 S
AIRBELT
E1 Kombi, E2 Turbo,
E3 Arctic White and
Red: Part #
8221AM01
E3 Black: Part
#
8221AM07
E Filter Box
includes a pre-motor
filter and an exhaust
microfilter
Part #8322AM
Parquet Brush
Part #6391DA
Wall & Floor Brush
Part #1325 S
Vario Kombi
Part #1397 S
Standard Brush
Part #8118ER

6
S ANDARD FEA URES OF ALL SEBO VACUUMS
Designed and anufactured in Germany – Legendary quality,
reliability and performance make SEBO vacuums the choice of
cleaning professionals throughout the world.
Excellent for Users With Allergies or Asthma – The British
Allergy Foundation recommends SEBO filters.
Tightly Sealed Vacuums Ensure Effective Filtration – Dirty air,
which flows through a vacuum, can only be filtered completely
if it does not escape into the room through seams or seals in
the machine. This is why all SEBO vacuums have tight seals
throughout. Many vacuum companies with high-filtration
claims are actually quoting specifications made by the manu-
facturer of the filter material, as measured in the laboratory,
not the filtration effectiveness of the vacuum itself while oper-
ating. Whether or not dirty air can escape through leaks in the
body of the machine is not considered. The filtration effective-
ness of SEBO vacuums is tested while they operate.
Save oney! SEBO Vacuums Last for Years and Extend Carpet
Life! – If properly maintained, SEBO vacuums save ordinary
residential users hundreds of dollars by providing excellent
performance for ten to fifteen years or more, and their deep-
cleaning power-brush technology extends the life of carpets.
Typical vacuums perform poorly, even when new, and usually
do not last beyond two years. So six or seven “disposable vacu-
ums” must be purchased during the average life expectancy of
just one SEBO machine.
Outstanding Warranty Coverage – SEBO is confident about the
quality of all its vacuums. Please refer to the Warranty Card
included with your SEBO vacuum cleaner for complete war-
ranty coverage information.
SEBO icrofilters Ensure Continuously Strong Suction
Performance – They are also long lasting, inexpensive and easy
to change in seconds.
Changing Bags is Easy and Clean – SEBO filter
bags can be changed in just a few seconds, and a
cap keeps dust sealed inside during removal and
disposal.
Effective Pet Hair Removal – All SEBO vacuums easily remove
pet hair!
SEBO’s FILTRATION SYSTE :
Bags are Better! – Top-fill, three- and four-
layer bags are an integral part of SEBO’s filtra-
tion system because they hold virtually all dirt
captured by the vacuum, which improves the
effectiveness and useful life of the microfilters.
They also ensure continuously strong suction
because dirt enters from the top, deposits at
the bottom, accumulates upward, and air exits through the sides,
which allows unimpeded airflow as they fill to capacity. And they
can be sealed when full, so no dust can escape into the air during
bag removal and disposal.
In contrast, without bags to hold nearly all the
captured dirt, the microfilters on bagless vac-
uums quickly clog from excessive dirt build-
up and must be replaced often, or a loss of
suction and cleaning effectiveness will occur.
In addition, dust and other allergens become
airborne when emptying bagless dirt contain-
ers. Lastly, bagless vacuum microfilters are expensive, usually
costing more than a multi-year supply of SEBO filter bags.
S-class Exhaust icrofilters –S-class
Exhaust Microfilters (S =“Schwebstoff” = air-
borne particles) are made from electrostati-
cally charged micro-fiber material, which
attracts and captures dust particles from the
airflow of the vacuum after it passes over the
motor to cool it. This means that exhaust air
is cleaned to the highest level. The S-class
Standard requires filters to absorb greater
than 99.9% of particles down to 0.3 microns in
diameter. For comparison, 100 microns is the
diameter of a human hair. Their advantages
are a relatively open texture that allows smoother airflow for
better suction performance, a longer life expectancy, and they
cost less than HEPA filters
Pre-motor Filters - Pre-motor filters clean suction air after it
passes though the filter bag, but before it passes over the vac-
uum motor. Cooling the motor with super-clean air increases
motor life and reduces the possibility of maintenance, even after
many years of use.

7
IDEN IFICA ION OF PAR S
Push the neck (11) of the hose (8) into the suction opening of the canister (16).
E3: The three notches in the suction opening (32) will line up with the three prongs on the
neck. When the notches are lined up correctly, the neck will snap firmly into place.
E1 & E2: The slot in the suction opening (31) will line up with the raised bar on the hose neck.
When lined up correctly, the neck will snap firmly into place.
To release the hose from the suction opening, press release buttons (14) on the neck of the hose (11),
and pull the neck out.
Connect the handle (1) to the top of the telescopic tube (5). Snap in place. To release the telescopic tube
(5) from the handle, push the handle release button (3) and slide the handle out.
Attach the head or brush to the bottom of the telescopic tube (5). Insert the bottom of the telescopic tube
into the neck (33) of the head or brush until it locks into place; or line up the square hole in the telescopic
tube with the notches in the front of the neck, and snap firmly into place. To release a head or brush from
the telescopic tube (5), push the release button (6), and pull the head or brush tool off the end of the tel-
escopic tube. The release button (6) is in the same position on all of the heads, brushes and power heads.
To attach the dusting brush clip (26) - E3: locate the two raised ridges on the upper end of the telescopic
tube (5) just below the handle. Push the clip onto the tube directly below the ridges then slide the clip
up until it locks onto the ridges. E1 & E2: Push the clip onto the tube and slide to desired position.
Snap the dusting brush (27) into the holder.
NOTE: To attach the ET-1 power head to your E3 Premium, please refer to your power head owner’s
manual for instructions. Attaching incorrectly could cause damage.
Brushes and Heads
28. Parquet brush - standard for the E3 Premiums and
E2 Turbo, optional for the E1 Kombi - Part #6391DA
7. Kombi nozzle - standard for the E1 Kombi, optional
for the E3 Premiums and E2 Turbo - Part #7260 S
29. Turbo nozzle - standard for the E2 Turbo, optional
for the E3 Premiums and E1 Kombi - Part #6780 S
30. ET-1 Power Head - standard for E3 Premiums
Part #9951AM - Black; #9258AM - White;
#9299AM - Red
23. Crevice nozzle
24. Upholstery nozzle
NOTE: All illustrations shown in this manual represent the E3 model except where part numbers and instructions are different for each model.
29
7
ASSEMBLY
30
1. Handle grip
2. Power control slider (E3 only)
3. Handle release button
4. Slide button
5. Telescopic tube
6. Tool release button
7. Kombi nozzle
8. Hose
9. Cable rewind button
10. On/off power control knob
(E1 & E2)
On/off knob (E3)
11. Hose neck
24
27
23
26
26. Dusting brush clip
27. Dusting brush
1
5
3
5
6
E1 & E2
Standard Attachments
28
1
2
3
4
5
6
7
8
9
10
11
12
17
13
11
14
15
16
17
18
19
20 10
9
21
22
23
24
25
12. Filter bag cover
13. Carrying handle
14. Hose neck release buttons
15. Warning indicator
16. Suction opening
17. Filter bag cover release catch
18. Parking attachment groove
19. Exhaust filter cover
20. Exhaust filter cover release buttons
21. Power cable
22. Parking attachment groove
23. Crevice nozzle
24. Upholstery Nozzle
25. AIRBELT shock absorber
E3
11 11
16 16
14
14
32
31
33

8
OPERA ING INS RUC IONS ALL AIRBEL E VACUUMS
Starting The achine - Figures 1, 2 & 3
Before turning on your canister, make sure that you have a firm hold on the handle grip to keep the
machine from moving forward.
1. With the canister main power control knob (10) in the OFF position, grasp the plug and pull the
power cord (21) out from the power cable recess (figure 1). The power cord (21) should be unwound
from the cable reel at least two thirds of its length. Note: do not over-extend the cord.
2. Plug the polarized power cord into a 120 volt wall outlet located near the floor.
3. Press the main power knob on the base of the canister (10) gently with your foot or hand. A blue
light will illuminate indicating that the power is on.
Operating the achine - Figures 1, 4, 5, 6, 7 & 8
Adjust the telescopic tube (5) to the correct height by pushing the slide button (4, figure 4) and gently
pulling the tube out to lengthen, or pushing it in to shorten. Release the slide button (4) to lock the tube
to the adjusted height.
When changing heads, always switch the vacuum off with the power control knob (10), and then unplug
the power cord.
The “bag full or clog” indicator (15, figure 5) works correctly only at full power. At lower power levels, the
“bag full or clog” indicator may show incorrectly. Check the status of the filter bag regularly at full power.
If the indicator remains orange at full power and the filter bag is not full, check for clogs (see page 13).
To retract the cord, switch the vacuum off, unplug it from the outlet, then push the power cable rewind
button (9, figure 1) and the mechanism will automatically rewind. Before rewinding the cable, always
switch off and unplug the vacuum. Hold the plug while rewinding the cord onto the cord reel. Avoid let-
ting the plug whip while rewinding.
WARNING! he quality, condition, coating, texture, age and manufacturing technique of all floor surfaces vary.
herefore, vacuums with rotating brushes, including your SEBO, may damage some floor coverings or surfaces. Some types
of high-gloss hardwood floors, cushion vinyl, berber carpets, long shag, and delicate or hand-woven carpets are particularly vul-
nerable to damage by rotating brushes. When possible, consult the materials supplied by your flooring manufacturer for infor-
mation on proper upkeep and cleaning. To ensure that your new SEBO vacuum cleaner is compatible with your floor, please
test the vacuum cleaner on each type of flooring surface in a small inconspicuous area to determine if any damage occurs.
If damage occurs, stop using the vacuum cleaner immediately!
!
Figure 4
Suction Control - Figure 3
E1 Kombi & E2 Turbo users: the suction control dial is located on the top side of the canister on the
power control knob (10). Rotate the dial clockwise for maximum suction. Rotate counter-clockwise to
reduce suction for vacuuming curtains or delicate fabrics.
E3 Premium users: The suction control slider (2) is located on the handle. For information on suction
control, refer to page 9 of this manual.
Figure 1
9
21
Figure 2
Figure 3 - E1 & E2
+
10
Figure 6
34
The vacuum can be stored with the canister in a horizontal or vertical position (figures 6, 7 & 8). The
Parquet brush, Kombi nozzle and Turbo nozzle have a parking tab located on the front of the neck (34).
Insert the parking tab into the upper side of the parking groove (18 or 22) and slide down firmly. For ver-
tical storage, or for easy carrying, use the parking groove on the underside (18). For horizontal storage,
use the parking groove on the end of the canister (22).
10
45
45
Figure 5
15
Figure 7
13
Figure 8
22
18

9
Starting The E3 Premium and Suction Control - Figures 1, 2, 9 & 10
Before turning on your canister, make sure that the vacuum handle is in its upright locked position
(figure 9).
1. With the canister main power control knob (10) in the OFF position, and the power control slider on
the handle (2, figure 10) in the OFF position, pull the power cord out from the base of the canister
(figure 1). The power cord should be unwound from the cable reel at least two thirds of its length.
Note: do not over-extend the cord.
2. Plug the polarized power cord into a 120 volt wall outlet located near the floor.
3. Press the main power control knob (10) on the base of the canister gently with your foot or hand.
The blue light will illuminate indicating that the power is on (figure 2).
4. Slide the Power Control Slider (2, figure 10) toward the MAX position. It will move freely between
0 suction and MAX suction. Set the slider to the suction desired.
0 = Zero Suction
MAX = Maximum Suction
ON position -
Move the slider toward MAX.
OFF position -
Pull the slider up to 0 suction
then continue pulling the
slider up until it “clicks” into
the OFF position.
Operating The E3 Premium - Figures 1, 11 & 12
When the power head is on with the handle in the upright locked position (see figure 9),
the brush roller will not spin.
To release the ET-1 power head from the upright locked position, press down on the foot
pedal, (35, figure 11) lower the handle into the normal operating position and push the
button on the top of the power head (36, figure 12) to engage the brush roller. The green
light on the power head will illuminate.
The handle can be lowered to a horizontal position useful for vacuuming under beds.
You may adjust the suction control with the power control slider (2) as you vacuum dif-
ferent surfaces or when using the accessory tools. For optimal cleaning and brushing,
operate the machine at the maximum suction power setting and push the power head
slowly over the carpet.
When the canister’s main power control knob is in the ON position, you may turn the
power head off and on with the power control slider (2). To turn the power head off using
the power control slider, pull the slider to 0 suction, then continue pulling the slider up
until it “clicks” into the OFF position. The green power head light will then shut off (the
blue light on the canister (10) will remain illuminated until the vacuum is powered off
using the main power control knob).
Always turn the power off on both the canister and the power head when changing
heads or unplugging the vacuum. Slide the power control slider on the handle to its OFF
position, press the power control knob on the base of the canister (10) gently with your
foot or hand, then unplug the canister to completely shut down the power when chang-
ing heads or storing the vacuum.
To retract the cord, switch the vacuum off, unplug it from the outlet, then then push the
power cable rewind button (9, figure 1) and the mechanism will automatically rewind.
Before rewinding the cable, always switch off and unplug the vacuum. Hold the plug while
rewinding the cord onto the cord reel. Avoid letting the plug whip while rewinding.
Please refer to your ET-1 power head owner’s manual for more information
ET-1 power head
ADDI IONAL OPERA ING INS RUC IONS FOR E3 WI H POWER HEAD
Figure 11
Figure 9
max.
0
Figure 10
2
35
Figure 12
36

10
Parquet Brush - Figure 17
The Parquet brush (28) is specially designed for use on hard surfaces. It is lightweight with soft
bristles, so it glides gently over floors and provides easy maneuverability. Fibers and hair can be
pulled out of the bristles manually, or vacuum the bristles with the telescopic tube.
Kombi Nozzle - Figure 18
The Kombi nozzle (7) is adjustable for carpet or hard floors. To set for carpet, slide the up arrow but-
ton (37) to the right until it clicks into place. The hard floor dusting brush will raise up allowing the
head to move over the carpet. To set for hard floors, slide the down arrow button (38) to the left until
it clicks into place. The brush will lower to gently sweep your floors. The slider in Figure 18 is set in
the position for hard floors. The brush should be cleaned regularly. Remove the Kombi nozzle from
the telescopic tube to clean. Fibers and hair can be pulled out of the bristles manually, or vacuum the
bristles with the telescopic tube. The brush strip is removable for cleaning and replacement.
Turbo Nozzle - Figure 19
The Turbo nozzle (29) has an air-driven rotating brush for gentle brushing of carpets. The Turbo noz-
zle can be adjusted for high and low pile carpet. To adjust the head for high pile carpet, push the slid-
er button (39) to the right. For low pile carpet, push the slider button (39) to the left. The slider in
Figure 19 is set in the low pile position. The rotating brush should be cleaned regularly. Remove the
Turbo nozzle from the telescopic tube to clean. Remove fibers and hair from the brush manually.
The telescopic tube (5) is useful for vacuuming corners and hard-to-reach areas. You may use the tel-
escopic tube without a brush, power head or attachment. To remove a brush or power head, switch off
the power control knob (10) and unplug the vacuum. Then, press the tool release button (6) and pull the
tube out of the head. The crevice nozzle (23) and upholstery nozzle (24) are stored on the bottom of the
canister (figure 14). The crevice nozzle, dusting brush (27) and upholstery nozzle may be inserted onto
the end of the tube. It is not necessary to turn off the vacuum while switching the standard attachments
(the crevice nozzle, upholstery nozzle or dusting brush). After use, switch off the power, unplug the vac-
uum and remove attachment. Re-insert the telescopic tube into the power head or brush, turning the
tube if needed, until you hear it click into place.
NOTE! E3 users with ET-1 power head, please refer to your power head user’s manual for more
detailed instructions for connecting your power head.
To use the hose without the telescopic tube, switch off the power and unplug the vacuum. Push the han-
dle release button (3) and pull the HANDLE out of the end of the telescopic tube. Do not try to separate the
hose from the handle! Insert the crevice nozzle (23), dusting brush (27) or upholstery nozzle (24) onto the
end of the handle (figure 15). You may also connect a head to the handle (figure 16). After use, switch off
the power, unplug the vacuum and remove the attachment. Re-insert the handle into the telescopic
tube making sure it is seated correctly and snap it into place.
Figure 15
Using the Telescopic Tube, Hose & Attachments - Figures 13, 14, 15 & 16
Figure 17
Figure 19
Figure 18
38
Always unplug vacuum from outlet before dismantling any part of machine!
!
USE AND MAIN ENANCE OF BRUSHES AND HEADS
37
39
L
L
28
7
L
L
29
Figure 14
To remove a brush or power head, switch off the power and unplug the vacuum. Then, press the
tool release button (6) and pull the tube out.
NOTE! E3 users with the ET-1 power head, please refer to your power head user’s manual for
more detailed instructions for operating and maintaining your power head.
Figure 13
6
5
5
24
23
23
24
1
1
1
5
7
30
Figure 16
Push button to release
upholstery nozzle.

11
VACUUM MAIN ENANCE
Changing the Filter Bag - Figures 20, 21 & 22
To change the filter bag (40), lift the filter bag release catch (17, figure 20) then lift open
the filter bag cover (12). Seal the used filter bag with the sealing cap (41). Tilt the green
sealing plate collar up (42, figure 21) and lift the bag out. Slide the front of the sealing plate
(42) of a new bag vertically into the bag holder (43, figure 22). Line up the sealing plate so
that the U-shaped metal spring (44) is positioned in the slot (44) of the collar and tilt it back
into place. Close the cover, making sure it snaps shut completely. The cover will not close
if the bag is inserted improperly. Do not re-use the filter bags. Note: the nature of the con-
tents of the filter bag will affect the point at which it needs changing. Fine dust may require
an earlier change even though the bag is not full. Fluff or hair allows air to pass through
easily, so the filter bag may overfill before the “bag full” indicator turns orange.
The “bag full or clog” indicator works correctly only at full power. At lower power levels, the
“bag full or clog” indicator may read incorrectly. Check the status of the filter bag regular-
ly at full power.
Changing the Pre-motor Filter - Figure 23
The pre-motor filter (46) needs to be changed when it becomes extremely dirty or clogged
with dust, or after approximately 10 to 20 filter bags have been used. To change the pre-
motor filter, lift the filter bag release catch (17, figure 20), lift open the filter bag cover (12)
and remove the filter bag. rasp the tab at the bottom of the filter (47, figure 23) and pull
the filter out and up. When the filter is horizontal, lift it out of the holder (48). Insert the
new filter into the holder horizontally (48) then swing it downward until the the tab (47)
locks into place. Replace the filter bag and the filter bag cover.
Figure 22
Figure 26
Always unplug vacuum from outlet
before dismantling any part of machine!
!
Pre-motor Filter
part of the E Filter Set
Part #8322AM
Exhaust Microfilter
part of the E Filter Set
Part #8322AM
Changing the Exhaust icrofilter - Figures 24, 25 & 26
After 10 to 20 bags have been used, change the exhaust microfilter (49). To remove the
exhaust microfilter, press the filter cover release buttons together (20, figure 24) and pull
the filter cover (19) off. Pull the material part of the filter out of the machine (49, figure
25). Press the red latches (50, figure 26) located on either side of the filter inward and pull
the filter out. Insert the opening of the new filter over the exhaust opening with the red
alignment tab at the bottom. When it is aligned, push down until the red latches (50) click
shut to hold the filter in place. Tuck the material part of the filter inside the opening.
Insert the cover by fitting the tabs on the top side of the cover into the grooves. Push the
cover closed, making sure it snaps shut completely.
Note: Never operate the vacuum with incorrectly attached filters or without filters, bag,
AIRBELT or filter bag housing cover (26). Do not re-use filter bags. Do not wash and
re-use filters.
Filter Bags
Part #8300AM
Figure 23
12 17
46
48
46
19
49
20
CLOSE
CLOSE
40
41
42
42
40
43
43
45 44
Figure 20
Figure 21
47
48
50
49
Figure 24 Figure 25
48
50

12
Changing the AIRBELT - Figures 27-33
Your E-Series vacuum cleaner is fitted with the patented AIRBELT shock absorber system,
which protects your walls and furniture and filters exhaust air. The AIRBELT shock
absorber system consists of the foam bumper (52) and the AIRBELT fabric cover (25). If
damage occurs to the AIRBELT cover, it will need to be replaced.
To remove the AIRBELT system (25 & 52), remove the upholstery nozzle from the rear of
the machine (figure 27), and lever out the nozzle holder (51) using a slot-head screwdriv-
er (figure 28). The AIRBELT system (25 & 52) can then be pried out of the recess with a
screwdriver (figure 29) and removed by carefully sliding the assembly toward the front of
the machine (figure 30). Remove the damaged cloth cover (25) from the foam bumper (52).
Fit the new AIRBELT cloth cover (25) over the foam bumper (52) by inserting the side rails
(53, figure 31) of the cloth cover (25) into the grooves (54) of the foam bumper. The upper
side rail of the cloth cover has a mark (55, figure 31). Insert the upper side rail with the
mark into the groove which is marked “TOP” (56, figure 31) Start from one end and con-
tinue fitting the cloth into the grooves around the bumper (figure 32). Fit the bumper
assembly to the front of the machine, then press in around the sides toward the rear (fig-
ure 33).
Refit the upholstery nozzle holder (51) under the parking groove (22) and tilt it down to lock
it into the lower side. Finally, re-insert the upholstery nozzle.
Figure 27
Note: Never operate the vacuum with incorrectly attached filters or without filters, bag, AIRBELT or filter bag housing cover
(12). Do not re-use filter bags. Do not wash and re-use filters.
Figure 28
24
22
51
Figure 29
25
AIRBELT Cover
E1 Kombi, E2 Turbo, E3 Arctic White and Red: Part #
8221AM01
E3 Black: Part # 8221AM07
52
Figure 30
25
52
53
25
54
55
56
Figure 31 Figure 32 Figure 33
52
25

CLOG REMOVAL
13
NOTE! E3 users with ET-1 power heads, please refer to your power head user’s
manual for more detailed instructions for removing clogs in your power head.
If the “bag full or clog” warning indicator (15) remains orange after the filter bag
has been changed and the filters are in good condition, there is likely a clog in the
system.
Clogs in the Head or Brush - Figure 34
Clogs in the swivel neck (56) of a head or brush can be cleared by first pressing the
tool release button (6) and removing the brush or head. Check inside the swivel neck
channel, and clean out pathway.
Clogs in the Telescopic Tube - Figure 34
Remove head from telescopic tube (5) by pushing the tool release button (6) and
pulling the tube out. Remove the hose from the top of the telescopic tube by pushing
the handle release button (3). A stiff wire or stick can be used to push the clog out of
the tube.
Clogs in the Hose - Figures 35, 36 & 37
Check for suction at the handle end of the hose. If you feel reduced suction, the block-
age is in the hose. To clear blockages in the hose (8), remove the handle (1) from the
telescopic tube by pressing the handle release button (3). Hold the hose upright with
one hand blocking the end of the handle (figure 36) and switch on the machine at full
power. If necessary, quickly lift your hand on and off the end of the hose.
Note: Do not insert a wire or stick into the hose. Doing so may cause damage to the
hose.
Clogs in Entrance to Filter Bag - Figures 38 & 39
Remove hose (10) from vacuum cleaner. To release the hose from the suction open-
ing, press release buttons (14) on the neck of the hose (11), and pull the neck out.
Check the hose neck (11) and suction opening (16) for clogs. If the clog is in the filter
bag opening, open the filter bag cover and clean out the entrance to the bag (57).
Always unplug vacuum from outlet before removing
any clogs!
!
Figure 39
Figure 34
56
6
5
3
5
1
3
57
Figure 36
Figure 38
Figure 35
1
Figure 37
11
16
8

14
ROUBLE-SHOO ING GUIDE
PROBLE
Does not turn on
Bag full or clog light on
Bag full or clog light on
& machine shuts off
Does not pick up
Filter bag door won’t
fully close
REASON
1. Telescopic tube not inserted properly.
2. Not plugged into working outlet.
3. Cable worn.
4. Hose neck (11) not inserted
properly into suction opening (16).
5. E3: The power control slider
switch is set to “0” (“off” position).
1. Bag full.
2. Clog in hose, telescopic tube,
brush or head, or entrance to
filter bag.
3. Exhaust microfilter dirty.
4. Pre-motor filter dirty.
1. Hose/handle assembly not
correctly inserted.
2. The suction control dial is rotated
to no suction setting
3. Filter bag cover not closed.
1. Filter bag cover not fully closed.
2. Bag not inserted properly
3. Pre-motor filter not properly
inserted.
SOLUTION
1. See page 7.
2. Use another outlet.
3. Replace cable.
4. See Assembly on page 7.
5. E3: Set slider switch to “on”
position. See page 9.
1. Replace filter bag. See page 11.
2. See Clog Removal on page 13.
E3 users with clog in power head
attachment: refer to clog removal
in the ET-1 owner ’s manual.
3. Replace exhaust microfilter.
See page 11.
4. Replace filter. See page 11.
1. Re-insert hose/handle assembly
making sure that it is lined up
properly and is snapped into
place. See page 7.
2. E1 & E2: Rotate suction control
clockwise for suction. See page 8.
3. See below.
1. Re-insert bag. Lock the cover
down firmly.
2. Re-insert bag. Lock the cover
down firmly.
3. Remove the filter bag and make
sure the pre-motor filter is seated
firmly in place (see pg. 11, figure 23).
Always unplug vacuum from outlet before dismantling any part of the machine!
!

15
AIRBEL E1 KOMBI AND E2 URBO SCHEMA IC AND PAR S LIS
CLOSE
37
32
31
30
20
21
2
18
23
19
14
16
5
38
36
34
33
26
25
1
4
3
19
24
19
13
12
9
10 11
19
29
27
18
18
8
6
7
17
15
19
19
35
28
22
39
Canister with Handle/Hose
39
30 31
Kombi Nozzle
standard with E1 Kombi
Turbo Nozzle
standard with E2 Turbo
Parquet Brush
standard with E2 Turbo
90602A E1 Kombi - Arctic White achine
Pos. Part # Description
18335WEER Bottom casing, white
2 8275 SER Castor front, gray-black
38276 SER Castor rear, gray-black
4 8249WEER Exhaust filter cover, white
58230 SER Technic module incl. pos. 6+7
6 7045ER Bag holder
78053ER Bolt 20 x 5/7
88212ER Engine mount gasket
9 8243ER Vac motor 120V
10 8282ULER Wire
11 8045ER Motor support
12 8220ER Noise limiting cover
13 8289ER Motor cover
14 665633ER Cable rewind unit, AM plug
15 8256ER Potentiometer pinion
16 8338ER On/Off button E1, cpl.
17 8292ER Printed circuit board
18 01036ER Screw 4 x 14
19 01017ER Screw STS 4 x 20 T20
20 8322AM Microfilter box E - pre-motor filter
and exhaust microfilter
21 8300AM Filter bags E
22 8328WEER Top casing, white
23 8340ER Top cover E1, inner part
24 8224WEE1ER Filter cover
25 8237ER Bumper
26 8221AM01 AIRBELT, gray-black
27 8213 SER Support
28 8066 S Crevice nozzle
29 8210 S Upholstery nozzle
30 1397 S Kombi nozzle, grey-black
32 6728ER Dusting brush & clip
33 8310 Hose cpl. incl. handle
34 6300 S Handle grip, cpl.
35 6303 S Retaining ring
36 8314 Hose E1
37 6237ER Telescopic tube
38 1735ER Release button, cpl.
91620A E2 Turbo - Dark Blue achine
Exceptions
1 8335DBER Bottom casing, dark blue
4 8249DBER Cover exhaust air filter, dark blue
22 8328DBER Top casing, dark blue
24 8224DBE2ER Filter cover
31 6780 S Turbo nozzle TT-C
39 6391DA Parquet brush
#91602AM E1 Kombi Arctic White
#91620AM E2 Turbo Dark Blue

16
AIRBELT E3 PREMIUM SCHEMATIC AND PARTS LIST
31
Parquet Brush standard
with E3 Premium
Canister with Handle/Hose
#91640AM E3 Premium - Black
#91641AM E3 Premium - Arctic White
#91642AM E3 Premium - Red
41
ET-1 Power Head
standard with
E3 Premium
91640AM E3 Premium - Black Machine
Pos. Part # Description
1 8335SWER Bottom casing, black
2 8275GSER Castor front, gray-black
3 8276GSER Castor rear, gray-black
4 8249SWER Cover exhaust air filter, black
5 8230GSER Technic module incl. Pos. 6+7
6 7045ER Bag holder
7 8053ER Bolt 20 x 5/7
8 8212ER Engine mount gasket
9 8243ER Vac motor 120V
10 8282ULER Wire
11 8045ER Motor support
12 8220ER Noise limiting cover
13 8289ER Motor cover
14 665633ER Cable rewind unit, AM plug
16 8339ER On/Off button E1, cpl.
17 8296ER Printed circuit board
18 01036ER Screw 4 x 14
19 01017ER Screw STS 4 x 20-T20
20 8322AM Filter box E - pre-motor filter and
exhaust microfilter
21 8300AM Filter bags E
22 8328SWER Top casing, black
23 8341ER Top cover E3, inner part
24 8224SWPRER Filter cover
25 8237ER Bumper
26 8221AM07 AIRBELT, organic
27 8213GSER Support
28 8066GS Crevice nozzle
29 8210GS Upholstery nozzle
31 6391DA Parquet brush.
32 6728ER Dusting brush & clip
33 8312 Hose E3 incl. handle
37 6270GS Telescopic tube
38 6420GS Release button cpl.
39 8320ER Cabling set
40 6369G1 Mains cable
91641AM E3 Premium - Arctic White Machine
1 8335WEER Bottom casing, white
4 8249WEER Cover exhaust air filter, white
22 8328WEER Top casing, white
24 8224WEPRER Filter cover
26 8221AM01 AIRBELT, gray-black
91642AM E3 Premium - Red Machine
1 8335DRER Bottom casing, red
4 8249DRER Cover exhaust air filter, red
22 8328DRER Top casing, red
24 8224DRPRER Filter cover
26 8221AM01 AIRBELT, gray-black
CLOSE
37
32
31
20
21
3
18
23
19
14
16
5
38
33
26
25
1
4
2
19
24
19
13
12
9
10 11
19
29
27
39
18
18
19
8
6
7
17
40
28
19
19
22
#91640AM E3 Premium Black
#91641AM E3 Premium Arctic White
#91642AM E3 Premium Red
29
Parquet Brush
standard with E3 Premium