SECO-LARM ENFORCER SD-9963-KSGQ User manual

Post-Mount
Wave-to-Open Sensor
with Access Box
SD-9963-KSGQ
Installation Manual
5024193
Conforms to
UL Std. 294
The ENFORCER Post-Mount Wa e-to-Open Sensor with Access Box is a full-featured exit plate
using IR technology to allow egress from a protected area or acti ate a de ice with just a
wa e of a
hand. Since it is touchless, it reduces contamination risks making it good
for hospitals, clinics, labs,
cleanrooms, schools, factories, or offices where no special clearance is required for exit or where a
longer-range sensor may cause unwanted acti ation. A manual o erride button is also pro ided.
•Adjustable sensor range up to 7" (18cm)
•Front panel is IP65 weatherproof for outdoor use
•1.2A Form C relay, adjustable output duration 0.5~30 seconds or toggle
•Gooseneck- or wall-mountable
•Manual o erride button
•LED-illuminated sensor area for easy identification
•Selectable LED colors (turns from red to green or green to red) on sensor acti ation
•Hinged stainless steel plate easily remo able for easy wiring
•Includes hea y-duty steel box
•Power must be pro ided by low- oltage power-limited/Class 2 power supply
•Use only low- oltage field wiring and do not exceed 98.5ft (30m)

Post-Mount Wave-to-Open Sensor with Access Box
2 SECO-LARM U.S.A., Inc.
Parts List
1x
Wave
-
to
-
Open Sensor
1x
Steel access box
4x
Mounting screws
2x
Ke s
1x
Manual
Specifications
Operating voltage 12~24 VDC
Current draw
(max. ±10%)
Standb red 18mA@12VDC / 23mA@24VDC
Triggered green 23mA@12VDC / 29mA@24VDC
Standb green 14mA@12VDC / 18mA@24VDC
Triggered red 28mA@12VDC / 35mA@24VDC
Rela t pe Form C dry contact (SPDT), 1.2A@24VDC
Response time 10ms
LEDs Standb Red*
Triggered Green*
Output duration 0.5~30 sec or toggle
Range 2"~7" (5~18 cm)
IP Rating IP65
†
Operating temperature -4°~131° F (-20°~55° C)
Dimensions 4"x5
1
/
2
"x3" (102x134x77 mm)
Weight 1-lb 9-oz (710g)
Destructive attack level Le el I
Line securit Le el I
Endurance level Le el IV
Standb power Le el I
*Color function re ersible
†
Front panel only
Overview
INSTALLATION NOTES:
•This product must be electrically wired and grounded in accordance with local codes or, in the absence of local
codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electrical Code CSA C22.1.
• Due to the nature of IR technology, an IR sensor can be triggered by a direct light source such as sunlight,
reflected light from a shiny object, or other direct light. Therefore, in some locations it may be necessary to install
a hood or other barrier to shield the sensor from direct light sources.
4
15
/
16
"
(125
m
m)
3
7
/
8
" (98m
m)
Locking mechanism
Sensor range adjustment
Output duration adjustment
LED control jumper
5-pin connector
Form C mechanical o erride button

Post-Mount Wave-to-Open Sensor with Access Box
SECO-LARM U.S.A., Inc. 3
Installation
1. Run four wires through the wall to the access box. Use only low- oltage, power-limited/Class 2
power supply and low- oltage field wiring not to exceed 98.5ft (30m).
2. Unlock and remo e the front plate from the access box.
3. Install the access box to the wall through the four mounting holes in the back, and thread the
four wires through the center hole.
4. Replace the front plate but lea e open and connect the four wires from the access box to the
wa e-to-open sensor according to the wiring diagram abo e.
5. Close and lock the front plate, taking care not to crimp the wires.
6. Remo e clear protecti e film from the sensor before use.
7. Make a copy of the key in case of loss. SECO-LARM does not offer replacement keys.
WARNING: Do not connect any de ice that will exceed 1.2A@24VDC.
Sample Wiring Diagram
Changing the LED Color
In the default LED configuration, red indicates
standby and green indicates triggered.
To change, simply mo e the LED control
jumper as shown in Fig. 1.
Red Wire: +12~24 VDC
Brown Wire: Ground (-)
Blue Wire: COM
Purple Wire: N.O.
Green Wire: N.C.
T pical Installation with an Electric Lock
Blue Wire: COM
Purple Wire: N.O.
Brown Wire: Ground (-)
Red Wire: +12~24 VDC
O erride button is factory prewired,
no further wiring necessary
Manual o erride
button
Green Wire: N.C. COM: N.O.
12~24 VDC
Power Supply
Standby: Red
Trigger: Green
(default)
Standby: Green
Trigger: Red
Fig. 1

Post-Mount Wave-to-Open Sensor with Access Box
Sensor Adjustment
Adjusting the Sensor Range and Output Duration
1. The sensor range can be adjusted 2"~7" (5~18 cm).
2. Output duration adjustable from 0.5 to 30 seconds or toggle*
NOTE: Do not force the adjustment trimpots. Only minimal force is required.
Care and Cleaning
The sensor requires special care to ensure reliability and a long operating life.
1. Use a soft, clean, preferably microfiber cloth for cleaning. Use the mildest type of cleaner a ailable.
2. When cleaning, spray the cleaning solution onto the cleaning cloth instead of the unit.
3. Wipe any excess liquid from the sensor. Wet spots may affect the sensor’s performance.
Troubleshooting
Sensor triggers
unexpectedly
•Ensure that no strong direct or reflected light source is reaching the sensor.
•Ensure that sensor is sheltered from direct sunlight.
Sensor remains
triggered
•Check that nothing is remaining in range of the sensor including a cone of 60º
from the centerline.
•Reduce the IR range of the sensor.
•Ensure that the sensor's output duration potentiometer is not turned to maximum
•Check that the power oltage is within the sensor's specifications.
Sensor will not
trigger
•Increase the IR range of the sensor.
•Check that the power oltage is within the sensor's specifications.
Output duration
adjustment
Sensor range
adjustment
Output duration: 0.5~30 seconds, toggle*
Default: 0.5 seconds
*Toggle: turn clockwise all the way to maximum
Sensor range: 2"~7" (5~18 cm)
Default: 7 (18cm)
5
cm
18cm
30s
0.
5
s
SECO-LARM ®U.S.A., Inc.
16842 Millikan A enue,
Ir ine, CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PITSW1
Order Part# 763-182-5%
MI_SD-9963-KSGQ_220902.docx
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal ser ice for one (1) year
from the date of sale
to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defecti e part if the unit is returned, transportation prepa
id, to
SECO-LARM. This Warranty is oid if damage is caused by or attributed
to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper
or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes o
ther
than defects in material and workmanship. The sole obligation of SECO-
LARM and the purchaser’s exclusi e remedy, shall be limited to the replacement or repair
only, at SECO-LARM’s option. In no e ent shall SECO-LARM be liable for any special, collater
al, incidental, or consequential personal or property damage of any kind
to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual de elopment and impro ement. For that reason, SECO-
LARM reser es the right to change specifications without
notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respecti e owners. Copyright © 2022
SECO-LARM U.S.A., Inc. All rights reser ed.
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause cancer and birth defect
s or other
reproducti e harm. For more information, go to www.P65Warnings.ca.go .
IMPORTANT: Users and installers of this product are responsible for ensuring that the insta
llation and configuration of this product complies with all national, state,
and local laws and codes. SECO-LARM will not be held responsible for the use of this product in iolation of any current laws or codes.
IMPORTANT WARNING: For a weather-resistant installation
, ensure that the unit is installed in a waterproof back box, and that the faceplate and faceplate screws
are properly sealed. Incorrect mounting may lead to exposure to rain or moisture inside
which could cause a dangerous electric shock, damage the de ice, and oid
the warranty. Users and installers are responsible for ensuring that this product is properly installed and sealed.