SECO-LARM SK-1011-SDQ User manual

SK-1011-SDQ
Access Control Keypad
Manual

Mounting
screws Installation
screws
SK-1011-SDQ
2
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Quick Installation Guide:
Mounting Diagram:
Quick Wiring Diagram:
This page is for installers looking to do a basic installation and programming of the keypad. For
more in-depth installation and programming instructions, see the Table of Contents on page 4.

3
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Quick Programming Guide:
This page is for installers looking to do a basic installation and programming of the keypad.
For more in-depth installation and programming instructions, see the Table of Contents on page 4.
Programming Tips:
•The master, super user, visitor, and user codes cannot be the same.
•A ashing amber LED indicates the keypad is in standby mode. A solid amber LED indicates the
keypad is in programming mode.
•If the keypad is set for Auto Code Entry Mode, all codes will need to be the same number of
digits as the master code (see pages 19~20).
Programming Instructions:
Follow the instructions below if the following covers your needs:
•A new master code.
•A single 4-digit user code for all users.
•One output to unlock a door.
•A 3-second delay time in opening the door after the output is activated.
1. Turn off the beeping before the 1-minute power-up period ends:
12 #
2. Enter Programming Mode:
0000 **
NOTE: 0000 is the default master code
3. Change the master code:
01 xxxx #
NOTE: xxxx is the new master code.
4. Set the user code to operate the output (unlock the door):
10 2 000 xxxx #
NOTE: 000 chooses user ID #000 of 1,000 possible users (000~999).
XXXX is the new user code for user ID #000.
5. Set the output delay time (skip this step if the default value of 5 seconds is acceptable):
51 3 #
NOTE: 3sets the output delay time for 3 seconds.
6. Exit Programming Mode:
**

4
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Table of Contents:
Quick Installation Guide..................................................................................................................... 2
Mounting Diagram ............................................................................................................................. 2
Quick Wiring Diagram........................................................................................................................ 2
Quick Programming Guide ................................................................................................................ 3
Table of Contents............................................................................................................................... 4
Features ............................................................................................................................................ 5
Specications .................................................................................................................................... 5
Overview............................................................................................................................................ 5
Parts List............................................................................................................................................ 5
LED Indicators and Keypad Sounds.................................................................................................. 6
Installation ......................................................................................................................................... 7
IMPORTANT NOTES ........................................................................................................................ 7
Wiring Diagram.................................................................................................................................. 8
Sample Applications .......................................................................................................................... 8
Getting Ready to Program................................................................................................................. 9
Programming Format and Default Programming Values................................................................. 10
System Restore................................................................................................................................11
Programming the Master Code ........................................................................................................11
Programming the Super User Code .......................................................................................... 12~13
Programming User Codes............................................................................................................... 14
Programming Visitor Codes............................................................................................................. 15
Programming the Output Mode and Output Timing......................................................................... 16
Programming the Real-Time Clock ................................................................................................. 17
Programming the Auto-Disable Time......................................................................................... 18~19
Programming the Wrong-Code System Lock-Up ............................................................................ 19
Programming the User Code Entry Mode ................................................................................. 19~20
Programming the Keypad Sounds................................................................................................... 20
Programming the Output Relay Activation Sounds ......................................................................... 20
Programming the Amber LED Flashing during Standby Mode........................................................ 21
Programming the Egress Delay/Warning .................................................................................. 21~22
Direct Access to Programming (DAP) ............................................................................................. 23
Notes ............................................................................................................................................... 23
User’s Guide to Operating the SK-1011-SDQ ................................................................................. 24
Also Available .................................................................................................................................. 24

5
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Features:
Specications:
Operating voltage 12~24 VAC/VDC
Current draw
(at 12VDC)
Standby 15mA
Keypress 30mA
Output 1 active 55mA
Total max current draw 90mA
Outputs Form C 1A@30VDC
Tamper 50mA@24VDC
Egress input N.O. Ground
Operating temperature -4°~158° F (-20°~70° C)
Operating humidity 5~95% Non-condensing
Dimensions (including back box) 45/8”x27/8”x1½” (117x73x38 mm)
Weight 6-oz (170g)
•12~24 VAC/VDC Auto-adjusting operation
•Up to 1,000 possible user codes (000~999)
•Up to 50 (01~50) possible temporary visitor
codes, which can be programmed for one-
time or limited-time use (1~99 hours)
•Output: Form C relay, 1A@30VDC max.
•Output can be programmed to activate for up
to 99,999 seconds (nearly 28 hours)
•Tamper output: N.C. Dry contact,
50mA@24VDC max.
•Mounts to a standard single-gang back box
(surface-mount back box included)
•All features are programmed directly from the
keypad: No need for an external programmer
•EEPROM Memory protects programmed
information in case of power loss
•Egress input lets users exit the premises
without keying in the code
Overview: Parts List:
1x Keypad
1x Back box
2x Installation screws
2x Mounting screws
1x Diode
1x Manual

6
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
LED Indicators and Keypad Sounds:
Keypad Sounds and Amber LED
Status Sounds(1) Amber LED (Center)
In programming mode –Steady ON
Successful key entry 1 Beep 1 Flash
Successful code entry 2 Beeps 2 Flashes
Unsuccessful code entry 5 Beeps 5 Flashes
Power up delay Continuous beeping Continuous ashing
Output relay activation(2) 1-Sec long beep –
In standby mode(3) –1 Flash/sec
System restore mode 2 Beeps Fast ashing for 2.5 min
Code already stored 1 Long beep –
Real-time clock stopped after
power loss
Continuous 3 fast beeps
every 5 seconds –
NOTE:
1. Keypad sounds can be programmed ON or OFF (see page 20).
2. Output relay activation sounds can be programmed for 1-sec long beep, 2 short beeps, or OFF
(see page 20).
3. Amber LED ashing during standby mode can be programmed ON or OFF
(see page 21).
LED Indicators
Red LED (Left) Amber LED (Center) Green LED (Right)
Steady Output inhibited Programming mode Output activated
Flashing Output inhibit paused Standby mode –

Mounting
screws Installation
screws
7
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Installation:
IMPORTANT NOTES:
1. Find a suitable location to mount the keypad. Install it at the height at which most users will be
able to easily operate the keypad.
2. Install one mounting screw on the wall. After the screw has been installed, hang the back box
by the top mounting hole.
3. Install the second mounting screw through the bottom hole.
4. Run the wire through the wall or conduit to the back box location, then run the wire through the
back box.
5. Connect the wires to the keypad according to the wiring diagram on page 8.
6. Finish assembly by attaching the keypad to the back box with the included installation screws.
1. Always disconnect power before servicing the keypad. Do not apply power until all connection
wiring is completed.
2. The keypad must be properly grounded. Use a minimum of 22AWG wire connected to the
ground terminal. Failure to do so may damage the keypad.
3. All wiring and programming should be done by a professional installer to reduce the risk of
improper installation.
4. The user’s guide for this keypad is located on page 24 of this manual. Be sure to store this
manual in a safe place for future reference.
IF USING THE KEYPAD WITH A MECHANICALLY
OPERATED DOOR OR GATE, MOUNT THE KEYPAD AT
LEAST 15’ (5m) FROM THE DOOR OR GATE TO PREVENT
USERS FROM BEING CRUSHED OR PINNED. FAILURE TO
DO SO MAY RESULT IN SERIOUS INJURY OR DEATH.

SK-1011-SDQ
OUTPUT 1
N.C. COM N.O.
(+) (-)
12~24V AC/VDC
EG
IN
TAMPER
N.C.
Connection terminals
8
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Connection Terminals
Terminal Description
Tamper N.C.
Tamper switch output, N.C. contact, max.
50mA@24VDC. Connect to the N.C. 24-hour
protection zone of an alarm if needed.
12~24 VAC/VDC Connect to a 12~24 VAC/VDC power supply.
Observe polarity.
Output 1 N.C.
NO/NC/COM, relay output,
max. 1A@30VDC
Output 1 COM
Output 1 N.O.
Egress Input N.O. Pushbutton contact to ground. Press
button to initiate door unlock output
Wiring Diagram:
Sample Applications:
Stand-Alone Door Lock:
In this application, the keypad is connected to a single door lock and an egress pushbutton.

9
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Getting Ready to Program:
Keypad Codes:
There are four types of keypad codes:
•Master code – Used only for entering programming mode; there can be only one master code
per keypad.
•Super user code – Can be used to activate the output, or to disable (inhibit) or enable the
operation of the output.
•User codes – Unique codes for each user to activate the output.
•Visitor codes – Temporary user codes that can be assigned to visitors or temporary workers to
activate the output; the visitor codes can be programmed for one-time use or to expire after a set
number of hours has passed.
Power Up the Keypad:
When the keypad is rst powered up, it will beep continuously for about 1 minute. During this
power-up time, if needed, use Direct Access to Programming (DAP) to reset the master code (see
“Direct Access to Programming (DAP)” on page 23).
1. Turn off the beeping before the 1-minute power-up period ends:
12 #
This will immediately stop the beeping.
When the beeping has ended, the keypad is ready for normal operation or for programming.
Enter and Exit Programming Mode:
All programming of the keypad is done in programming mode.
1. Enter programming mode:
xxxx **
NOTE: XXXX is the master code. 0000 is the default master code
(see “Programming the Master Code” on page 11 to program a new master
code). The amber LED will turn to a steady ON to indicate that the keypad is in
programming mode.
2. Exit programming mode:
**
The ** entry can be used to exit programming mode at any time while programming. The
amber LED will return to ashing, indicating standby mode, upon exiting programming mode.
NOTE: DO NOT DISCONNECT THE KEYPAD FROM POWER WHILE IN PROGRAMMING
MODE. Disconnecting the keypad while in programming mode could cause a keypad
memory error.

10
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming Format and Default Programming Values:
In this manual, the format used for programming the keypad is as follows:
•A 2-digit ( XX ) FUNCTION identier to tell the keypad what is being programmed.
•A varying number of digits ( X ) to represent the parameters of that FUNCTION.
•The # key to conrm programming of the FUNCTION.
The following is a list of the different programming functions:
Function Parameters Default functions and values Page #
01 Master code Default 0000, code length from 4~8 digits 11
02 Super user code No default, must be programmed 12~13
10 User codes No default, must be programmed 14
40 Visitor codes No default, must be programmed 15
51 Output mode and output timing 5-Second output, momentary 16
55 System real-time clock No default, must be programmed 17
56 Auto-disable time No default, must be programmed 18~19
60 Wrong-code system lock-up Locks keypad after 10 false code/card tries 19
70 User code entry mode Manual entry of “#” after each code 19~20
71 Keypad sounds Programming and operation beeps enabled 20
72 Output relay activation sounds 1-Second beep when output is activated 20
73 Amber LED standby ashing Center LED ashes on standby 21
90 Egress delay/warning Egress output happens immediately 21~22
NOTE: The Direct Access to Programming (DAP) code 2828 (page 23) and the system restore
code 9999 (page 11) are xed and cannot be changed, even via programming.

11
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
System Restore:
Programming the Master Code:
System restore will reset all programming values except the master code back to the default values
shown on page 10.
1. Make sure the keypad is in programming mode (see “Enter and Exit Programming Mode” on
page 9).
2. Initiate system restore:
9999 #
NOTE:
•System restore will reset ALL programming except the master code back to default values. Be
careful to use system restore only when absolutely necessary.
•System restore may take several minutes. The amber LED will ash rapidly during this time.
•Once system restore has been completed, the keypad will beep twice to show that all
programming values have been reset to their default values and are ready to be
re-programmed.
•At this point, the keypad is still in programming mode.
The master code is used to enter programming mode. The master code does not serve as a user
code for activating the output.
1. Make sure the keypad is in programming mode (see “Enter and Exit Programming Mode” on
page 9).
2. Enter new master code:
01 xxxx #
NOTE:
•XXXX represents the new master code, which can be 4 to 8 digits long.
•There can be only one master code for the keypad.
•Programming a new master code will overwrite the previous master code.
•If the master code is forgotten, use Direct Access to Programming (DAP) to reset the master
code (see page 23).
•The master, super user, visitor, and user codes cannot be the same.
•If the keypad is set for Auto Code Entry Mode, all codes will need to be the same number of
digits as the master code (see “Programming the User Code Entry Mode” on pages 19~20).

12
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the Super User Code:
The super user code has multiple functions:
•The super user code can activate or deactivate the output at any time.
•The super user code can toggle operation of the output on or off.
•The super user code can pause or restart the timed output auto-disable period.
•The super user code can enable or disable the output.
•The super user code is exempt from any system inhibition or lockup functions. It is valid
at any time.
Programming the Super User Code:
1. Make sure the keypad is in programming mode (see “Enter and Exit Programming Mode” on
page 9).
2. Enter the new super user code:
02 xxxx #
NOTE:
•XXXX represents the new super user code, which can be 4 to 8 digits long.
•There can be only one super user code for the keypad.
•Programming a new super user code will overwrite the previous super user code.
•The master, super user, visitor, and user codes cannot be the same.
Deleting the Super User Code:
This function is useful for protecting the premises in case the super user code is forgotten.
To delete a super user code:
1. Make sure the keypad is in programming mode (see page 9).
2. Enter:
02 #
Using the Super User Code:
In these examples, assume the super user code is 2580.
1. Activate or deactivate the output (timed or toggle, depending on programming):
2580 # 1

13
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the Super User Code (continued):
2. Toggle operation of the output ON or OFF:
2580 # 7
NOTE:
•This function is used to leave the output active for extended periods of time.
•While the output remains active, the green LED remains lit.
•Do not forget to deactivate this function after its use is no longer required.
•It is recommended to only use this function with fail-safe locks.
3. Temporarily pause or restart the timed output auto-disable period:
2580 # 8
NOTE:
•This function is used to enable the operation of the output if it was disabled using the auto-
disable function (see pages 18~19).
•When the output auto-disable function is inactive, the red LED will ash steadily. This
indicates that the output may now be used.
4. Disable or enable the output (toggle, regardless of programming):
2580 # 9
NOTE:
•This is used to prevent users from accessing the protected premises.
•For more information on programming timed or toggle mode, see “Programming the Output
Mode and Output Timing” on page 16.
•The red LED will remain steady on while the output is disabled.
•For safety reasons, the egress button works regardless of whether the output is enabled or
disabled via the super user code.
•The super user code continues to operate the output even while that output is disabled.

14
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming User Codes:
When programming user codes, use this general formula:
10 A BBB CCCC #
10 – Program User Codes
A– Add or delete a user code
B – User ID
C – User Code
Output:
•10 – Output, up to 1,000 possible user codes.
Code Addition / Deletion:
•2– Add a user code.
•5 – Delete a programmed user code.
•0999 – Delete all programmed user codes.
User IDs:
•000 to 999 – 1,000 unique user IDs for user codes for the output.
User Codes:
•A user code can be 4 to 8 digits long, and must have the same length as all other codes if the
keypad is used in auto code entry mode (see “Programming the User Code Entry Mode” on
pages 19~20).
•The master, super user, visitor, and user codes cannot be the same.
Examples:
1. Program user code 2275 for user ID #010 for the output:
10 2 010 2275 #
2. Delete code for user ID #002 for the output:
10 5 002 #
3. Delete all users for the output:
10 0999 #

15
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming Visitor Codes:
Visitor codes are temporary codes that expire after use or after a specied amount of time has
elapsed. While active, they operate the output as normal user codes.
NOTE: If the keypad is powered down, any programmed visitor codes will be deleted.
When programming visitor codes, use this general formula:
40 aa bb cccc #
40 – Program Visitor Codes
a – Visitor ID
b – Valid Duration (hours)
c – Visitor Code
Visitor IDs:
•01 to 50 – 50 unique visitor IDs for visitor codes for the output.
•0999 – Delete all currently programmed visitor codes.
Valid Duration:
•00 – Set a one-time code. This code can only be used once by a visitor, after which it is
automatically deleted.
•01 to 99 – Set the duration the visitor code will be valid, from 1 to 99 hours.
Visitor Codes:
•A visitor code can be 4 to 8 digits long, and must have the same length as all other codes if the
keypad is used in auto code entry mode (see “Programming the User Code Entry Mode” on
pages 19~20).
Examples:
1. Set the visitor ID #01 code to 1268, and make it a one-time code:
40 01 00 1268 #
2. Set the visitor ID #02 code to 1378, and make it valid for three hours:
40 02 03 1378 #
3. Delete the visitor ID #02 code from memory:
40 02 #

16
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the Output Mode and Output Timing:
The relay for the output can be programmed to trigger ON and OFF with a user code (toggle
mode), or to trigger for a programmed length of time of up to nearly 28 hours before automatically
turning OFF. The toggle or timed outputs can be used for locking or unlocking a door or for a
variety of functions that can be controlled with the keypad.
When programming the output mode and time, use this general formula:
51 AAAAA #
51 – Program Output Mode and Time
A – Output Mode and Time
Output Mode and Time:
•0 – Start/stop (toggle) mode. In this case, the output starts when a user code is entered, and
stops when a user code is entered.
•1to 99999 – The output triggered by a user code lasts 1 to 99,999 seconds (nearly
28 hours) before automatically turning off (default 5 seconds).
NOTE: While the keypad is in momentary timed output mode, the output can be reset any time
by entering the super user code.
Examples:
In these examples, assume that the super user code is 2580.
1. In programming mode, set the output to toggle:
51 0 #
2. In programming mode, set the output to 60 seconds:
51 60 #
3. Reset the output timer:
2580 # 1

17
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the Real-Time Clock:
A 24-hour real-time clock provides the baseline time needed to start and stop the output auto-
disable time (see “Programming the Auto-Disable Time” on pages 18~19).
If the auto-disable time is not programmed, it is not necessary to set the real-time clock.
To set the clock, use this general formula:
55 HHMM #
55 – Program Real-Time Clock
HH – Hours
MM – Minutes
Setting Hours and Minutes:
•HH represents hours and MM represents minutes in the military (24-hour) time format,
from 00:00 to 23:59.
Examples:
1. Set the real-time clock to 11:30 AM:
55 1130 #
2. Set the real-time clock to 7:15 PM:
55 1915 #
NOTE:
•If the auto-disable time is programmed, losing power will cause the keypad to beep 3 times
every 5 seconds. To deactivate this alert, either reset the real-time clock or clear the auto-disable
time.
•If the auto-disable time is not programmed, losing power will not cause the keypad to beep.
•To ensure accurate time, it is advised to re-program the real-time clock every three to six months and
when Daylight Savings Time begins and ends (if applicable).

18
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
The keypad can be programmed so that the output is disabled for a certain period of time every
day. The output will be disabled at the start time, and will be re-enabled at the end time. This
ensures that users are not allowed into the protected premises, such as during lunch hour or at
night.
NOTE:
•The real-time clock must be operating in order to set the output auto-disable time (see
“Programming the Real-Time Clock” on page 17).
•For safety purposes, the egress button still works while the output is auto-disabled.
•The time is set using the military (24-hour) time format (00:00 to 23:59).
•If the programmed start time is before the end time, the output is auto-disabled within a single
day. If the programmed start time is after the end time, the end time will be on the
following day.
•The start time and end time cannot be the same.
•The auto-disable time can be temporarily paused and restarted using the super user code (see
“Programming the Super User Code” on pages 12~13).
•During the auto-disable time, the super user code can be used to operate the output.
•The red LED will remain lit during the auto-disable time.
When programming the auto-disable time, use this general formula:
56 HHMM HHMM #
56 – Program Auto-Disable Time
HHMM – Start Time
HHMM – End Time
Start Time:
•Start time for the auto-disable time. HH represents hours and MM represents minutes in
the military (24-hour) time format, from 00:00 to 23:59.
End Time:
•End time for the auto-disable time. HH represents hours and MM represents
minutes in the military (24-hour) time format, from 00:00 to 23:59.
Examples (in these examples, assume that the super user code is 2580):
1. In programming mode, set the auto-disable time from 12:00 PM to 1:00 PM:
56 1200 1300 #
2. In programming mode, set the auto-disable time from 6:30 PM to 7:30 AM the following day:
56 1830 0730 #
Programming the Auto-Disable Time:

19
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
3. In programming mode, clear the auto-disable time:
56 #
4. Temporarily pause or resume the auto-disable time:
2580 # 8
5. Activate the output during the auto-disable time (i.e. open the protected door):
2580 # 1
Programming the Auto-Disable Time (continued):
Programming the Wrong-Code System Lock-Up:
The keypad can be programmed to lock up in order to secure the premises against unauthorized
entry if multiple wrong codes are entered.
When programming the wrong-code system lock-up, use this general formula:
60 aa #
60 – Program Wrong-Code System Lock-Up
AA – Lock Options
Lock Options:
Choose from several different options for the wrong-code system lock-up security level:
•1– After 10 successive false attempts using incorrect user codes, the keypad will lock for 60
seconds (default).
•5to 10 – After 5 to 10 successive false attempts using incorrect user codes, the keypad
will lock for 15 minutes or until the super user code is used as follows:
SUPER USER CODE # 9
•00 – No system lock-up will happen.
NOTE: The keypad’s red LED will remain lit to show that the keypad is locked.
Programming the User Code Entry Mode:
The keypad can be programmed for auto or manual user code entry modes:
•Auto entry mode – Pressing the # key is not required after typing in a user code. In auto entry
mode, all user codes must have the same number of digits as the master code.
•Manual entry mode – The #key must be pressed after the user code to indicate the code has
been entered completely. In this case, the user codes can have a different number of digits, from
4 to 8 digits.

20
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the User Code Entry Mode (continued):
Programming the Keypad Sounds:
Some of the keypad sounds can be programmed off:
•Keypad audible mode – All the keypad’s status beeps are enabled.
•Keypad silent mode – The successful key entry beep (1 beep) and the unsuccessful user code
entry beeps (5 beeps) are disabled. However, the warning and power-up delay beeps remain
active. This provides for a quieter work environment.
To Program:
•To enable keypad audible mode (default):
71 1 #
•To enable keypad silent mode:
71 0 #
NOTE: This programming function only impacts the keypad sounds. It does not impact the output
relay activation sounds (see “Programming the Output Relay Activation Sounds” below).
To Program:
•For auto entry mode:
70 1 #
•For manual entry mode (default):
70 2 #
NOTE: If the keypad was previously programmed for manual code entry mode and then is
reprogrammed for auto entry mode, any codes whose length exceeds the number of
digits of the master code will no longer operate the keypad. However, if the keypad is
reprogrammed for manual entry mode, the longer codes will again operate the keypad.
Programming the Output Relay Activation Sounds:
The keypad output sounds can be programmed for one of three modes:
•No beeps – The keypad will not beep when the output is activated:
72 0 #
•1-second beep (default) – The keypad will beep for 1 second when the output is activated:
72 1 #
•2 short beeps – The keypad will beep twice when the output is activated:
72 2 #
NOTE: This programming function only impacts the output relay activation sounds. It does not
impact the keypad sounds (see “Programming the Keypad Sounds” above).