SECO-LARM Enforcer SK-1123-FDQ User manual

SK-1123-FDQ
Vandal Resistant Flush-Mount
Access Control Keypad
Manual

CUTOUT
WALL
Installation
screws
2
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Quick Installation Guide:
Mounting Diagram:
Quick Wiring Diagram:
This page is for installers looking to do a basic installation and programming of the keypad. For
more in-depth installation and programming instructions, see the Table of Contents on page 4.
SK-1123-FDQ

3
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Quick Programming Guide:
This page is for installers looking to do a basic installation and programming of the keypad.
For more in-depth installation and programming instructions, see the Table of Contents on page 4.
Programming Tips:
• The master, super user, visitor, duress, and user codes cannot be the same.
• A ashing amber LED indicates the keypad is in standby mode. A solid amber LED indicates
the keypad is in programming mode.
• If the keypad is set for Auto Code Entry Mode, all codes will need to be the same number of
digits as the master code (see page 24).
Programming Instructions:
Follow the instructions below if the following covers your needs:
• A new master code.
• A single 4-digit user code for all users.
• One output to unlock a door.
• A 3-second delay time in opening the door after the output is activated.
1. Turn off the beeping before the 1-minute power-up period ends:
12 #
2. Enter Programming Mode:
0000 **
NOTE: 0000 is the default master code.
3. Change the master code:
01 xxxx #
NOTE: xxxx is the new master code.
4. Set the user code to operate output #1 (unlock the door):
10 2 000 xxxx #
NOTE: 000 chooses user ID #000 of 1,000 possible users (000~999).
XXXX is the new user code for user ID #000.
5. Set the output #1 delay time (skip this step if the default value of 5 seconds
is acceptable):
51 3 #
NOTE: 3sets the output #1 delay time for 3 seconds.
6. Exit Programming Mode:
**

4
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Table of Contents:
Quick Installation Guide..................................................................................................................... 2
Mounting Diagram ............................................................................................................................. 2
Quick Wiring Diagram........................................................................................................................ 2
Quick Programming Guide ................................................................................................................ 3
Table of Contents............................................................................................................................... 4
Features ............................................................................................................................................ 5
Specications .................................................................................................................................... 5
Parts List.............................................................................................................................................5
Overview............................................................................................................................................ 6
LED Indicators and Keypad Sounds.................................................................................................. 6
Installation ......................................................................................................................................... 7
IMPORTANT NOTES ........................................................................................................................ 7
Wiring Diagram.................................................................................................................................. 8
Sample Applications ...................................................................................................................... 8~9
Sample Applications for Output #2 .................................................................................................. 10
Getting Ready to Program................................................................................................................11
Programming Format and Default Programming Values................................................................. 12
System Restore............................................................................................................................... 13
Programming the Master Code ....................................................................................................... 13
Programming the Super User Code .......................................................................................... 14~15
Programming User Codes............................................................................................................... 16
Programming Visitor Codes for Output #1....................................................................................... 17
Programming Duress Codes ..................................................................................................... 18~19
Programming the Output Mode and Output Timing......................................................................... 20
Programming the Real-Time Clock ................................................................................................. 21
Programming the Output #1 Auto-Disable Time........................................................................ 22~23
Programming the Wrong-Code System Lock-Up ............................................................................ 23
Programming the User Code Entry Mode ....................................................................................... 24
Programming the Keypad Sounds................................................................................................... 24
Programming the Output Relay Activation Sounds ......................................................................... 25
Programming the Amber LED Flashing during Standby Mode........................................................ 25
Programming the Door-Forced-Open Warning and Timing............................................................. 25
Programming the Door-Propped-Open Warning and Timing .......................................................... 26
Programming the Egress Delay/Warning .................................................................................. 26~27
Direct Access to Programming (DAP) ............................................................................................. 28

5
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Features:
Specications:
Parts List:
Operating voltage 12~24 VAC/VDC
Current draw
(at 12VDC)
Standby*15mA
Keypress 40mA
Output 1 active 65mA
Output 1 & 2 active 66mA
Total max current draw 100mA
Outputs
#1 – Form C 1A@30VDC
#2 – Transistor Ground 100mA@24VDC
Duress 100mA@24VDC
Interlock 100mA@24VDC
Tamper 50mA@24VDC
Inputs
Egress N.O. Ground
Door sensor N.C. Ground
Door inhibit N.O. Ground
Operating temperature -4°~158° F (-20°~70° C)
Operating humidity 5~95% Non-condensing
IP Rating IP66
Dimensions (including back box) 4¾”x3⁄”x1⁄” (120x80x46 mm)
Weight 16.2-oz (460g)
•12~24 VAC/VDC auto-adjusting operation
•Up to 1,000 possible user codes (000~999)
programmable for output #1 and 100 (001~100)
for output #2
•Up to 50 (01~50) possible temporary visitor codes,
which can be programmed for one-time or limited-
time use (1~99 hours)
•Output #1: Form C relay, 1A@30VDC max.
•Output #2: Transistor ground, 100mA@24VDC
•Outputs #1 and #2 can be programmed to activate
for up to 99,999 seconds (nearly 28 hours)
•Tamper output: N.C. Dry contact, 50mA@24VDC
max.
•Mounts to standard single-gang back box
•IP66 Weatherproof rating
•Keypad illuminates when a button is pressed;
backlight can be programmed for FULL or AUTO in
standby mode
•All features are programmed directly from the
keypad: No need for an external programmer
•EEPROM Memory protects programmed
information in case of power loss
•Up to 50 (01~50) duress codes for output #1,
10 (01~10) for output #2
•Duress code signals a silent alarm if an authorized
user is forced to open the door under duress
•Egress input lets users exit the premises without
keying in the code
•Door sensor input for anti-tailgating operation
•Interlocking input for connecting to a second
keypad
• 1x Keypad
• 2x Security screws
• 1x Security Wrench
• 1x Diode
• 1x Manual
*Keypad LEDs off

6
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
1¾”
(44mm)
2⁄”
(66mm)
⁄”
(15mm)
1⁄”
(46mm)
1¼”
(31mm)
LED Indicators and Keypad Sounds:
Keypad Sounds and Amber LED
Status Sounds(1) Amber LED (Center)
In programming mode –Steady ON
Successful key entry 1 Beep 1 Flash
Successful code entry 2 Beeps 2 Flashes
Unsuccessful code entry 5 Beeps 5 Flashes
Power up delay Continuous beeping Continuous ashing
Output relay activation(2) 1-Sec long beep –
In standby mode(3) –1 Flash/sec
System restore mode 2 Beeps Fast ashing for 2.5 min
Code already stored 1 Long beep –
Real-time clock stopped after
power loss
Continuous 3 fast beeps
every 5 seconds –
NOTE:
1. Keypad sounds can be programmed ON or OFF (see page 24).
2. Output relay activation sounds can be programmed for 1-Sec long beep, 2 short beeps, or OFF
(see page 25).
3. Amber LED ashing during standby mode can be programmed ON or OFF (see page 25).
LED Indicators
Red LED (Left) Amber LED (Center) Green/Red LED (Right)
Steady Output #2 activated Programming mode Output #1 activated (Green)
Output #1 inhibited (Red)
Flashing – Standby mode Inhibit mode paused (Red)
Overview:
3⁄”
(80mm)
4¾”
(120mm)

CUTOUT
WALL
Installation
screws
7
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Installation:
IMPORTANT NOTES:
1. Find a suitable location to mount the keypad. Install it at the height at which most users will be
able to easily operate the keypad.
2. The keypad can be installed in a single-gang back box or can be ush-mounted directly to
the wall.
•If ush-mounting the keypad, cut out a 25/8”x13/4”x11/4” (66x44x32 mm) hole to t the back
portion of the keypad. Leave room for the keypad wiring and wiring hole.
3. Run the wire through the wall or conduit to the keypad location, then run the wire through the
hole on the back of the keypad.
4. Refer to the wiring diagram (page 8) and ensure that the backlit jumper is properly set.
5. Connect the wires to the keypad according to the wiring diagram on page 8.
6. Finish assembly by attaching the keypad to the single- gang back box with the included security
screws, or by ush-mounting the keypad in the already-cut hole in the wall.
1. Always disconnect power before servicing the keypad. Do not apply power until all connection
wiring is completed.
2. The keypad must be properly grounded. Use a minimum of 22AWG wire connected to the
ground terminal. Failure to do so may damage the keypad.
3. All wiring and programming should be done by a professional installer to reduce the risk of
improper installation.
IF USING THE KEYPAD WITH A MECHANICALLY
OPERATED DOOR OR GATE, MOUNT THE KEYPAD AT
LEAST 15’ (5m) FROM THE DOOR OR GATE TO PREVENT
USERS FROM BEING CRUSHED OR PINNED. FAILURE TO
DO SO MAY RESULT IN SERIOUS INJURY OR DEATH.

TAMPER
N.C.
O/P 2
N.O.
DU
OUT
EG
IN
(–)
GND
DOOR SENS.
O/P 1
INHIB
INT
LOCK
(+) (–)
12~24 VAC/DC
OUTPUT 1
N.C. | COM | N.O.
FULL AUTO
BACK-LIT
BUZZER
+
+
+
+
Connection terminals
Backlit jumper
Connection terminals
Stand-Alone Door Lock:
In this application, the keypad is connected to a single door lock and an egress pushbutton.
8
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Connection Terminals
Tamper N.C.
Tamper switch output, N.C. contact,
max. 50mA@24VDC.
Connect to the N.C. 24-hour protection zone of
an alarm if needed.
12~24 VAC/VDC Connect to a 12~24 VAC/VDC power supply.
Observe polarity.
Output 1 N.C.
NO/NC/COM, relay output,
max. 1A@30VDC
Output 1 COM
Output 1 N.O.
Output 2 N.O. Transistor ground output, max. 100mA@24VDC.
Duress Output
Transistor ground output, max. 100mA@24VDC.
Triggers a silent alarm or other device when the
user enters a duress code.
Egress Input N.O. Pushbutton contact to ground. Press button to activate Output #1
Ground (-) Common ground output.
Door Sensor Connect to an optional N.C. sensor such as a magnetic contact to monitor if a door is open or
closed. Connect to ground (–) if not used.
Output 1 Inhibit Output #1 inhibitor. N.O. input, connect to Interlock Control of second keypad if needed so that if
one keypad is used to open a door, the other is temporarily disabled.
Interlock Control Interlock Control. N.O. input, connect to Output #1 Inhibit of second keypad if needed so that if one
keypad is used to open a door, the other is temporarily disabled.
Wiring Diagram:
Jumper Settings
Jumper Position Description
Backlit Full Dim backlit during standby. Full backlit for 10 seconds after any button press.
Auto No backlit during standby. Full backlit for 10 seconds after any button press.
Sample Applications:

9
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Sample Applications (continued):
Inter-Lock System Using Two Keypads:
In this application, two keypads are each connected to separate door locks and egress
pushbuttons. While one door is open, the other cannot be opened.
• Use an N.C. magnetic contact or some other N.C. device to detect whether a door is opened or
closed. Do this for the two doors being protected.
1

O/P 2
N.O.
DU
OUT
EG
IN
(-)
GND
N.C.
+12VDC
O/P 2
N.O.
DU
OUT
EG
IN
(-)
GND
O/P 2
N.O.
N.C.
N.C.
N.C.
OUTPUT #1
COM
COM
COM
N.O.
N.C.
OUTPUT #1
COM
N.O.
O/P 2
N.O. O/P 2
N.O.
DU
OUT
EG
IN
(-)
GND
O/P 2
N.O.
DU
OUT
EG
IN
(-)
GND
DOOR
SENS
O/P 1
INHIB
INT.
LOCK
N.C.
or
N.O.
TO ALARM
CONTROL PANEL
PROTECTION ZONE
Terminals in Alarm
Control Panel for
connecting Remote
Arm/Disarm control
switch
NO or NC Contact
ALARM CONTROL PANEL
IN4004
N.C.
COM
N.O.
WARNING
•Make sure nobody is inside
the house before starting
the door lock inhibit
function.
•The inhibit authorization
code should always be
kept by only the owner.
12VDC
Power
Supply
12VDC
Power
Supply
+
+
+
+
-
-
-
-
Electric Lock
Electric Lock
N.O.
N.O.
O/P 2
N.O.
DU
OUT
EG
IN
(-)
GND
N.C.
+12VDC
O/P 2
N.O.
DU
OUT
EG
IN
(-)
GND
O/P 2
N.O.
N.C.
N.C.
N.C.
OUTPUT #1
COM
COM
COM
N.O.
N.C.
OUTPUT #1
COM
N.O.
O/P 2
N.O. O/P 2
N.O.
DU
OUT
EG
IN
(-)
GND
O/P 2
N.O.
DU
OUT
EG
IN
(-)
GND
DOOR
SENS
O/P 1
INHIB
INT.
LOCK
N.C.
or
N.O.
TO ALARM
CONTROL PANEL
PROTECTION ZONE
Terminals in Alarm
Control Panel for
connecting Remote
Arm/Disarm control
switch
NO or NC Contact
ALARM CONTROL PANEL
IN4004
N.C.
COM
N.O.
WARNING
•Make sure nobody is inside
the house before starting
the door lock inhibit
function.
•The inhibit authorization
code should always be
kept by only the owner.
12VDC
Power
Supply
12VDC
Power
Supply
+
+
+
+
-
-
-
-
Electric Lock
Electric Lock
N.O.
N.O.
N.C.
OUTPUT #1
COM
COM
N.O.
O/P 2
N.O.
+-
+-
Electric Lock
IN4004
IN4004 N.C.N.O.
12VDC
Power Supply
N.C.
COM
N.C.
OUTPUT #1
COM
N.O.
O/P 2
N.O.
+
-
+
-
Electric Lock
N.O.
IN4004
IN4004
12VDC
Power
Supply
10
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
1. Drive an Optional Output Relay
2. Connecting Inhibit Control
•Use a 12VDC relay and connect it to the same
12V power supply as the keypad.
•Using this setup, the owner may enter the user
code for output #2 to disable output #1 during a
certain period to prevent unauthorized access.
•Set output #2 to start/stop (toggle) mode (see
page 20).
•Connect the output 1 inhibit terminal with the
output 2 N.O. terminal as shown in wiring
diagram.
•Output #1 is invalid while the O/P 1 INHIB
terminal is shunted to ground via output #2.
3. For Door-Hold-Open Mode
•For N.C. locking devices: Connect a relay
to output #2 in series with the locking device.
•For N.O. locking devices: Connect a relay to
output #2 in parallel with the locking device.
Sample Applications for Output #2:

11
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Getting Ready to Program:
Keypad Codes:
There are ve types of keypad codes:
•Master code – Used only for entering programming mode; there can be only one master code
per keypad.
•Super user code – Can be used to activate outputs #1 and #2, or to disable (inhibit) or enable
the operation of output #1.
•User codes – Unique codes for each user to activate outputs #1 or #2.
•Visitor codes – Temporary user codes that can be assigned to visitors or temporary workers to
activate output #1; the visitor codes can be programmed for one-time use or to expire after a set
number of hours has passed.
•Duress codes - Assigned to specic users as a way to send a silent alert if forced to use keypad
under duress.
Power Up the Keypad:
When the keypad is rst powered up, it will beep continuously for about 1 minute. During this
power-up time, if needed, use Direct Access to Programming (DAP) to reset the master code (see
“Direct Access to Programming (DAP)” on page 28).
1. Turn off the beeping before the 1-minute power-up period ends:
12 #
This will immediately stop the beeping.
When the beeping has ended, the keypad is ready for normal operation or for programming.
Enter and Exit Programming Mode:
All programming of the keypad is done in programming mode.
1. Enter programming mode:
xxxx **
NOTE: XXXX is the master code. 0000 is the default master code
(see “Programming the Master Code” on page 13 to program a new master code).
The amber LED will turn to a steady ON to indicate that the keypad is in programming
mode.
2. Exit programming mode:
**
The ** entry can be used to exit programming mode at any time while programming. The
amber LED will return to ashing, indicating standby mode, upon exiting programming mode.
NOTE: DO NOT DISCONNECT THE KEYPAD FROM POWER WHILE IN
PROGRAMMING MODE. Disconnecting the keypad while in programming mode
could cause a keypad memory error.

12
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming Format and Default Programming Values:
In this manual, the format used for programming the keypad is as follows:
•A 2-digit ( XX ) FUNCTION identier to tell the keypad what is being programmed.
•A varying number of digits ( X ) to represent the parameters of that FUNCTION.
•The # key to conrm programming of the FUNCTION.
The following is a list of the different programming functions:
Function Parameters Default functions and values Page #
01 Master code Default 0000, code length from 4~8 digits 13
02 Super user code No default, must be programmed 14~15
10 User codes for output #1 No default, must be programmed 16
20 User codes for output #2 No default, must be programmed 16
40 Visitor codes for output #1 No default, must be programmed 17
41 Duress codes for output #1 No default, must be programmed 18~19
42 Duress codes for output #2 No default, must be programmed 18~19
51 Output mode for output #1 5-Second output, momentary 20
52 Output mode for output #2 5-Second output, momentary 20
55 System real-time clock No default, must be programmed 21
56 Auto-disable time No default, must be programmed 22~23
60 Wrong-code system lock-up Locks keypad after 10 false code/card tries 23
70 User code entry mode Manual entry of “#” after each code 24
71 Keypad sounds Programming and operation beeps enabled 24
72 Output relay activation sounds 1-Second beep when output is activated 25
73 Amber LED standby ashing Center LED ashes on standby 25
80 Door-forced-open warning Warning disabled 25
81 Door-propped-open warning Warning disabled 26
90 Egress delay/warning Egress output happens immediately 26~27
NOTE: The Direct Access to Programming (DAP) code 2828 (page 28) and the system restore
code 9999 (page 13) are xed and cannot be changed, even via programming.

13
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
System Restore:
System restore will reset all programming values except the master code back to the default values
shown on page 12.
1. Make sure the keypad is in programming mode (see “Enter and Exit Programming Mode” on
page 11).
2. Initiate system restore:
9999 #
NOTE:
•System restore will reset ALL programming except the master code back to default values. Be
careful to use system restore only when absolutely necessary.
•System restore may take several minutes. The amber LED will ash rapidly during this time.
•Once system restore has been completed, the keypad will beep twice to show that all
programming values have been reset to their default values and are ready to be
re-programmed.
•At this point, the keypad is still in programming mode.
Programming the Master Code:
The master code is used to enter programming mode. The master code does not serve as a user
code for activating outputs #1 or #2.
1. Make sure the keypad is in programming mode (see “Enter and Exit Programming Mode” on
page 11).
2. Enter new master code:
01 xxxx #
NOTE:
•XXXX represents the new master code, which can be 4 to 8 digits long.
•There can be only one master code for the keypad.
•Programming a new master code will overwrite the previous master code.
•If the master code is forgotten, use Direct Access to Programming (DAP) to reset the master
code (see page 28).
•The master, super user,visitor,duress and user codes cannot be the same.
•If the keypad is set for Auto Code Entry Mode, all codes will need to be the same number of
digits as the master code (see “Programming the User Code Entry Mode” on page 24).

14
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the Super User Code:
The super user code has multiple functions:
•The super user code can activate or deactivate output #1 and #2 at any time.
•The super user code can toggle operation of output #1 on or off.
•The super user code can pause or restart the timed output #1 auto-disable period.
•The super user code can enable or disable output #1.
•The super user code is exempt from any system inhibition or lockup functions. It is valid at any
time.
Programming the Super User Code:
1. Make sure the keypad is in programming mode (see “Enter and Exit Programming Mode” on
page 11).
2. Enter the new super user code:
02 xxxx #
NOTE:
•XXXX represents the new super user code, which can be 4 to 8 digits long.
•There can be only one super user code for the keypad.
•Programming a new super user code will overwrite the previous super user code.
•The master, super user, visitor, duress, and user codes cannot be the same.
Deleting the Super User Code:
This function is useful for protecting the premises in case the super user code is forgotten.
To delete a super user code:
1. Make sure the keypad is in programming mode (see page 11).
2. Enter:
02 #
Using the Super User Code:
In these examples, assume the super user code is 2580.
1. Activate or deactivate output #1 (timed or toggle, depending on programming):
2580 # 1
2. Activate or deactivate output #2 (timed or toggle, depending on programming):
2580 # 2

15
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the Super User Code (continued):
3. Toggle operation of output #1 ON or OFF:
2580 # 7
NOTE:
•This function is used to leave output #1 active for extended periods of time.
•While output #1 remains active, the green LED remains lit.
•Do not forget to deactivate this function after its use is no longer required.
•It is recommended to only use this function with fail-safe locks.
•All functions requiring use of the door sensor input are suspended while this function
is in use.
4. Temporarily pause or restart the timed output #1 auto-disable period:
2580 # 8
NOTE:
•This function is used to enable the operation of output #1 if it was disabled using the auto-
disable function (see pages 22~23).
•When the output #1 auto-disable function is inactive, the red LED will ash steadily. This
indicates that output #1 may now be used.
5. Disable or enable output #1 (toggle, regardless of programming):
2580 # 9
NOTE:
•This is used to prevent users from accessing the protected premises.
•For more information on programming timed or toggle mode, see “Programming the Output
Mode and Output Timing” on page 20.
•The red LED will remain steady on while output #1 is disabled.
•For safety reasons, the egress button works regardless of whether output #1 is enabled or
disabled via the super user code.
•The super user code continues to operate output #1 even while that output is disabled.

16
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming User Codes:
When programming user codes, use this general formula:
AA B CCC DDDD #
A– Output
B– Add or delete a user code
C – User ID
D – User Code
Outputs:
•10 – Output #1, up to 1,000 possible user codes.
•20 – Output #2, up to 100 possible user codes.
Code Addition / Deletion:
•2– Add a user code
•5 – Delete a programmed user code.
•0999 – Delete all programmed user codes for the selected output.
User IDs:
•000 to 999 – 1,000 unique user IDs for user codes for output #1.
•001 to 100 – 100 unique user IDs for user codes for output #2.
User Codes:
•A user code can be 4 to 8 digits long, and must have the same length as all other codes if the
keypad is used in auto code entry mode (see “Programming the User Code Entry Mode” on
pages 19~20).
•The master, super user, visitor,duress, and user codes cannot be the same.
Examples:
1. Program user code 2275 for user ID #010 for output #1:
10 2 010 2275 #
2. Delete code for user ID #002 for output #2:
20 5 002 #
3. Delete all users for output #1:
10 0999 #

17
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming Visitor Codes for Output #1:
Visitor codes are temporary codes that expire after use or after a specied amount of time has
elapsed. While active, they operate output #1 as normal user codes.
NOTE:
•Visitor codes cannot be used to deactivate the duress output (see “Operating Duress Codes” on
page 19).
•If the keypad is powered down, any programmed visitor codes will be deleted.
When programming visitor codes, use this general formula:
40 aa bb cccc #
40 – Program Visitor Codes
a – Visitor ID
b – Valid Duration (hours)
c– Visitor Code
Visitor IDs:
•01 to 50 – 50 unique visitor IDs for visitor codes for output #1.
•0999 – Delete all currently programmed visitor codes.
Valid Duration:
•00 – Set a one-time code. This code can only be used once by a visitor, after which it is
automatically deleted.
•01 to 99 – Set the duration the visitor code will be valid, from 1 to 99 hours.
Visitor Codes:
•A visitor code can be 4 to 8 digits long, and must have the same length as all other codes if the
keypad is used in auto code entry mode (see “Programming the User Code Entry Mode” on
page 24).
Examples:
1. Set the visitor ID #01 code to 1268, and make it a one-time code:
40 01 00 1268 #
2. Set the visitor ID #02 code to 1378, and make it valid for three hours:
40 02 03 1378 #
3. Delete the visitor ID #02 code from memory:
40 02 #
4. Delete all currently programmed visitor codes
40 0999 #

18
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming Duress Codes:
Duress codes allow users to trigger a silent alarm or alert if they are forced to allow access to a
protected area. If a user uses a duress code instead of his or her normal user code, outputs #1 or
#2 will activate as normal, but the duress output will simultaneously activate to trigger a silent alarm
or alert.
NOTE:
•Duress codes are always valid and are not inhibited by any other operation of the keypad.
•Duress codes cannot be the same as any other codes.
•The duress code should be easy to remember. For instance, it can be the same as a user’s
normal user code, but with a single digit changed, as by subtracting or adding 1 to the rst or last
digit of the code. For example, if the user code is 1369, a good duress code might be 2369.
When programming duress codes, use this general formula:
AA BB CCCC #
A– Output
B – Duress ID
C – Duress Code
Outputs:
•41 – Output #1
•42 – Output #2
Duress IDs:
•01 to 50 – Up to 50 duress codes can be programmed for output #1.
•01 to 10 – Up to 10 duress codes can be programmed for output #2.
•0999 – Delete all currently programmed duress codes for the selected output
Duress Codes:
•A duress code can be 4 to 8 digits long and must have the same length as all other codes if the
keypad is used in auto code entry mode (see “Programming the User Code Entry Mode” on
page 24)
Examples:
1. Set the duress ID #01 code for output #1 to 2369:
41 01 2369 #

19
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming Duress Codes (continued):
2. Set the duress ID #01 code for output #2 to 23980:
42 01 23980 #
3. Delete the duress ID #01 code for output #1 from memory:
41 01 #
4. Delete all duress codes for output #1 from memory:
41 0999 #
Operating Duress Codes:
If a duress code is used in place of a normal user code, both the appropriate outputs #1 or #2 and
the duress output will be activated. However, a duress code cannot deactivate the duress output.
Only a normal user code, super user code, or a master code can deactivate the duress output.
Examples:
In these examples, assume that 2369 is an output #1 duress code and that 1369
is a user code.
1. Activate the duress output and output #1 using the duress code:
2369 #
NOTE: Subsequently entering the duress code will activate output #1 again, but will not
deactivate the duress output.
2. Deactivate the duress output using the user code:
1369 #

20
ENFORCER Vandal Resistant Flush-Mount Access Control Keypad
SECO-LARM U.S.A., Inc.
Programming the Output Mode and Output Timing:
The relay for outputs #1 and #2 can be programmed to trigger ON and OFF with a user code
(toggle mode), or to trigger for a programmed length of time of up to nearly 28 hours before
automatically turning OFF. The toggle or timed outputs can be used for locking or unlocking a door
or for a variety of functions that can be controlled with the keypad.
When programming the output mode and time, use this general formula:
AA BBBBB #
A– Output
B– Output Mode and Time
Outputs:
•51 – Output #1
•52 – Output #2
Output Mode and Time:
•0 – Start/stop (toggle) mode. In this case, the output starts when a user code is entered, and
stops when a user code is entered.
•1to 99999 – The output triggered by a user code lasts 1 to 99,999 seconds (nearly
28 hours) before automatically turning off (default 5 seconds).
NOTE: While the keypad is in momentary timed output mode, the output can be reset any time
by entering the super user code.
Examples:
In these examples, assume that the super user code is 2580.
1. In programming mode, set output #1 to toggle:
51 0 #
2. In programming mode, set output #2 to 60 seconds:
52 60 #
3. Reset output #1 timer:
2580 # 1
4. Reset output #2 timer.
2580 # 2