SECO-LARM Enforcer E-941DA-1K2P User manual

ENFORCER ®
Also available:
Installation Manual
E-941SA-1200
E-941SA-600
E-941SA-300
Electromagnetic Locks
E-941DA-1K2P
Double-Door
1200 lb. maglock
with status LEDs &
status sensors
E-941SA-1K2PD
1200 lb. maglock
with status LED
status sensor &
delay timer
Status LED
Status LED
When power is applied to the magnetic lock, it turns on the unit's powerful built-
in electromagnet. This electromagnet is attracted to the steel armature plate
which is mounted on a door, holding the door fast against unauthorized entry.
When power to the magnetic lock is turned off, the electromagnet releases the
armature plate, allowing the door to open.
SPECIFICATIONS
Power
Magnet Size
Armature Size
Holding Force
Current Drain
Voltage Tolerance
Housing
Temperature
Weight
Certifications
E-941SA-600
12VDC/24VDC
97/8x 11/16 x 15/8in.
(250 x 27 x 42 mm)
71/4x 1/2x 11/2in.
(185 x 12 x 38 mm)
600 lb. (272kg)
500mA @ 12VDC
250mA @ 24VDC
± 10%
Aluminum
14° ~ 131°F
(-10° ~ 55°C)
4 lb. 6oz. (2.0kg.)
UL, CUL, CE
E-941SA-1200
12VDC/24VDC
10½ x 15/8x 25/8in.
(268 x 42 x 67 mm)
71/4x 5/8x 23/8in.
(185 x 16 x 61 mm)
1200 lb. (545kg)
500mA @ 12VDC
250mA @ 24VDC
± 10%
Aluminum
14° ~ 131°F
(-10° ~ 55°C)
11 lb. (5.0kg)
UL, CUL, CE
HOW THEY WORK
E-941SA-300
12VDC
63/4x 15/16 x 11/4in.
(170 x 23 x 32 mm)
6 x 3/8x 11/4in.
(152 x 10 x 32 mm)
300 lb. (136kg)
315mA @ 12VDC
± 10%
Aluminum
14° ~ 131°F
(-10° ~ 55°C)
2 lb. 13.5oz. (1.29kg.)
CE

ELECTROMAGNETIC LOCK Installation Manual
SECO-LARM U.S.A., Inc.Page 2
MOUNTING THE E-941SA-300, E-941SA-600 & E-941SA-1200
A. Drill holes for the mounting plate and
armature plate (see fig. 1 and 2) by
doing the following:
1. Fold the mounting template along
the dotted line.
2. Close the door. Find a mounting
location on the door frame near
the upper free-moving corner of
the door, as close to the corner of
the door frame as possible.
3. Place the template against the
door and frame.
4. Drill two holes in the door frame
and three holes in the door as
indicated on the template.
NOTE — A filler plate or an L-bracket
or Z-bracket (optional) may be
required for the electromagnet,
depending on the door frame. See
fig. 1. Z/L brackets are not available
for E-941SA-300.
B. Mount the armature plate to the door
using at least two steel and one
rubber washer (fig. 2):NOTE — Actual
installation varies according to door
style.
1.
Put one rubber washer between
two steel washers, and place them
over the armature screw between
the armature plate and the door.
This will allow the armature plate
to pivot slightly around the
armature screw in order to
compensate for door misalignment.
2. Tighten the sexnut bolt enough so
the armature plate can withstand
the force of someone attempting to
break down the door while the
electromagnet is engaged.
3. Do not tighten the armature plate
against the door. The plate must
be able to pivot around the
armature screw.
4. Make sure the anti-spin guides are
in the two guidepin holes.
C. Screw the mounting plate to the door
frame or optional bracket:
1. Screw the two short self-tapping
screws in the slotted holes of the
mounting plate and adjust the
position of the mounting plate so
that it and the armature plate form
a 90-degree angle.
2. Once the position is correct, use
the long self-tapping screws to
permanently mount the bracket.
3. Remove the two short screws.
D. Drill the cable access hole.
E. Mount the electromagnet to the door
frame (fig. 1) — Use the Allen wrench
to screw the socket-head mounting
screws through the bottom of the
electromagnet into the mounting
bracket. (Brass sleeves will be needed
for the E-941SA-600.)
F. Connect the power leads (fig. 3):
1. Open the electromagnet.
2. Run two power leads from the
power supply through the cable
access hole into the
electromagnet.
3. Connect the power leads to the
terminal block.
4. Close the electromagnet.
Note:
E-941SA-300 is for 12VDC
operation only. Connect the red wire to
+12VDC, and the black wire to ground.
G. Test the unit.
H. Insert the tamper caps into the
mounting screw access holes. This
should be the last step, as once the
tamper caps are in place, they will be
difficult to remove.

ELECTROMAGNETIC LOCK Installation Manual
Page 3
Filler
Plate*
Standard
Mounting "Z"
Bracket
For Inswing Doors
"L" Bracket
*Note:mayrequiremore
than one filler plate.
12345678
12345678
12345
12345
Power
Supply
Control
Device
+
-
Voltage Selection
12VDC
Magnet set for 12VDC
operation as supplied
from factory.
Position a jumper over the
two middle pins for 24VDC
operation.
24VDC
Important note:
Check jumper settings before connecting the
lock to the 24VDC input power. Damage to the
lock may result from incorrect jumper settings.
Sexnut tube
Sexnut
bolt
This side drill
16mm only
Drill a 8mm
hole thru door
Armature
Screw
Steel and
Rubber
washers
(as
needed)
Armature
HOLLOW METAL DOOR
Drill an 8mm hole thru door. From sexnut
bolt side only, enlarge the 8mm hole to
16mm.
Drill an 8mm hole thru door. From sexnut
bolt side of door, drill 12.7mm (1/2") hole,
25mm (1") in depth.
Drill a 6.8mm dia. hole and tap for
M8 x 1.25 thread.
Sexnut
bolt
Drill 12.7mm
(1/2") Drill a 8mm
hole thru door
Armature
Screw
Armature
SOLID CORE DOOR
Armature Screw
Tap M8 x 1.25 Thread
REINFORCED DOOR
Armature
FIG.
1
FIG.
2
FIG. 3
12345
12345
ENFORCER
Power Cable
To Magnet
Voltage Selection
12VDC
Magnet set for 12VDC
operation as supplied
from factory.
Position a jumper over the
two middle pins for 24VDC
operation.
24VDC
INPUT
POWER
ENFORCER
Control
Device
Power
Supply
+
-
+
-
E-941SA-600
E-941SA-1200
Power Cable
To Magnet
Steel and
Rubber washers
(as needed)
Steel and
Rubber washers
(as needed)
(E-941SA-600 &
E-941SA-1200 only)
+
-
INPUT POWER
(Z/L brackets are not available for E-941SA-300.)

ELECTROMAGNETIC LOCK Installation Manual
SECO-LARM U.S.A., Inc.Page 4
E-941SAd.pmd
PITGW1
®
NOTICE
The information and specifications printed in this manual are current at the time of publication.
However, the SECO-LARM policy is one of continual development and improvement. For this reason,
SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not
responsible for misprints or typographical errors.
Copyright © 2003 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced
or copied, in whole or in part, without the written permission of SECO-LARM.
REGULAR MAINTENANCE
• Clean the contact surfaces of the electromagnet or armature plate with a soft cloth and non-
abrasive, non-corrosive cleaner.
• Apply a light coat of a silicon lubricant to prevent rust. Wipe away the excess.
• Check that the armature plate is securely attached to the door, yet can pivot slightly around the
armature screw.
• Check that the electromagnet is securely attached to the door frame.
TROUBLESHOOTING
Problem:
Door does not lock
Door locks, but can be
easily forced open
Delay in door releasing
Possible cause:
No power
Poor contact between
electromagnet and
armature plate
Incorrect voltage
setting
A secondary diode was
installed across the
electromagnet
Solutions:
• Check to make sure the wires are
securely tightened to the terminal block
• Check that the power supply is connected
and operating
• Make sure the lock switch is wired
correctly
• Make sure the electromagnet and
armature plate are properly aligned
• Make sure the contact surfaces of the
electromagnet and armature plate are
clean and free from rust
• Check the power leads with a meter, and
make sure 12VDC or 24VDC is present
• The electromagnet is fitted with a metal
oxide varistor to prevent interference, so
do not install a secondary diode
SECO-LARMSECO-LARM
SECO-LARMSECO-LARM
SECO-LARM®U.S.A., Inc.U.S.A., Inc.
U.S.A., Inc.U.S.A., Inc.
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]
Website: www.seco-larm.com
E-mail: sales
@ seco-larm.com
WARRANTY: ENFORCER Electromagnetic Locks are warranted against defects in
material and workmanship while used in normal service for a period of one (1) year from the
date of sale to the original customer. Our obligation is limited to the repair or replacement of any
defective part if the unit is returned, transportation pre-paid, to SECO-LARM.
UL CERTIFICATION
E-941SA-600 and E-941SA-1200 electromagnetic locks conform to UL/10B “Fire Tests of Door
Assemblies” and UL/10C “Positive Pressure Fire Tests of Door Assemblies” for swinging door
assemblies. They are also classified in accordance with the Uniform Building Code standard 7-2.

ELECTROMAGNETIC LOCK Installation Manual
Page 5