SECO-LARM E-941S-600DPSQ Series User manual

Electromagnetic Locks
Installation Manual
E-941SA-1K2DPSQ shown
Model*** Holding Force** Material
E-941Sx-600DPSQ* 600-lb (272kg) Anodized aluminum
E-941Sx-1K2DPSQ* 1,200-lb (545kg) Anodized aluminum
E-941Sx-600PQ† 600-lb (272kg) Anodized aluminum
E-941Sx-1K2PQ† 1,200-lb (545kg) Anodized aluminum
E-941Sx-1K2PD‡ 1,200-lb (545kg) Anodized aluminum
*With status LED, bond sensor, and door position sensor †With status LED and bond sensor ‡With status LED, bond sensor, and timer
**Holding force has not been verified by UL ***"x" is the variable for product color "A" for aluminum, "B" for black, and "D" for dark bronze
 MOV surge protection
 Adjustable mounting bracket
 Complete mounting hardware for typical installations
 "L" bracket and "Z" brackets available for easy mounting
 Detachable faceplate
 12/24VDC selectable
NOTES:
 UL294 Indoor use
 The power for the E-941Sx series is to be provided by a Listed (UL294 or UL603) Class 2 Power Supply.
 The E-941Sx series is intended to be used as an access control system accessory which is installed in
accordance with the manufacturer’s installation and operation instructions, ANSI/NFPA 70 and the local
authority having jurisdiction.
 The minimum permissible wire size to be used shall not be less than 22AWG

SECO-LARM Electromagnetic Locks
2 SECO-LARM U.S.A., Inc.
Hex-head
mounting screws
Steel washers x2
Armature screw
Mounting plate
Short self
-
tapping
screws x2
Door spacer
Armature plate
Rubber washer
Long self
-
tapping
screws x4
Sexnut bolt
Armature plate
holder*
Electromagnet
Tamper caps x2
Guide pins
Parts List
1x
Electromagnet
1x
Armature plate
2x
Short self
-
tapping screws
1x
Armature screw
2x
Steel washers
1x
Rubber washer
4x
Long self
-
tapping screws
1x
Sexnut bolt
2x
Guide pins
1x
Door spacer
2x
Hex
-
head mounting screws
1x
Mounting plate
2x
Tamper caps
2x
Hex wrenches
1x
Armature plate
holder
*
1x
Manual
Specifications
Holding Force 600-lb 1,200-lb.
Operating voltage 12/24 VDC
Current
draw
12VDC 500mA
24VDC 250mA
Bond sensor SPDT relay, 3A@12VDC
Door position sensor Reed switch, 0.2A@12VDC
Operating temperature 32°~120° F (0°~49° C)
Dimensions Magnet 913/16"x111/16"x1" (250x43x25 mm) 101/2"x27/16"x19/16" (267x62x40 mm)
Armature 71/4"x11/2"x1/2" (185x38x12 mm) 71/4"x27/16"x5/8" (184x62x16 mm)
Destructive attack Level I
Line Security Level I
Standby power Level I
Endurance Level IV
Overview
*Armature plate holder for E-941Sx-600DPSQ and E-941Sx-1K2DPSQ only

SECO-LARM Electromagnetic Locks
SECO-LARM U.S.A., Inc. 3
Installation Applications
 When mounting the electromagnet, it may be necessary to use a "Z" and "L" bracket, an
"L" bracket, a "U" bracket, and/or plate spacers, depending on the location and the type of door
and frame.
 Use the diagram below to help decide whether or not an optional bracket will be necessary for
installation.
Installation Notes
1. Read this installation manual thoroughly. A clear understanding of the product and this manual
will make installation much easier.
2. The electromagnetic lock is designed for indoor use ONLY.
3. The most suitable mounting location for the electromagnetic lock may require the use of
additional SECO-LARM accessories such as Z-brackets, L-brackets, and/or spacer plates.
Please see the diagram on page 3 to decide if a particular application requires any mounting
accessories.
4. Do not run power wires and signal wires in the same conduit as this may cause interference.
5. Do not install a diode in parallel with the electromagnetic lock as this may cause a delay when
releasing the door as well as cause residual magnetism.
6. The best location to install the electromagnetic lock is on the inside of the door that is being
secured with the wiring concealed in the frame to prevent tampering with the unit.
7. The minimum permissible wire size to be used shall not be less than 22AWG.
Typical Installation Plate Spacers "L" Bracket
"L" Bracket and "Z" bracket "U" Bracket Armature Mounting Plate

SECO-LARM Electromagnetic Locks
4 SECO-LARM U.S.A., Inc.
Installation
1. Fold the mounting template along the
dotted line to form a 90-degree angle.
Dril l 3.2mm ( / ”) hole (2 plac es)
18
FOLD ON DOTTED LINE
PLACE AGAINST H EADER
Drill 8mm ( / ”) hole for ca ble acce ss
516
Magnet
Drill 6mm ( / ”) hole for guide pins (12mm ( / ”) in depth)
1412
PLAC E AGA INS T DOO R
Drill 8mm ( / ”) hole for armature scre w
516
Armature
1200-lb Electromagnetic Lock
E-941SA-1K2DPSQ
MT_E-941SA-1K2DPSQ_210115.cdr
2. Close the door. Find a mounting location
on the door frame near the upper free-
moving corner of the door, or as close as
possible to the upper corner of the door
frame opposite the hinges.
Ideal
mounting
location
Door frame
3. Use a hammer to lightly
tap the two guide pins into
the guide pin holes on the
armature plate.
4.
Place the template against
the door and frame. Mark
where the holes are to be
drilled.
Door frame
Template
Door
5. Drill holes in the frame and
the door as shown on the
template and in step #6
below. The smaller holes on
the door should not go all
the way through.
Door frame
Door
See step
#6 below
6. Depending on the type of door being protected, drill holes according to the diagrams below:
Drill a
5
/
16
" hole (8mm) diameter hole
through the armature-plate side of the
door for the armature screw. Then drill a
5/8
" (16mm) diameter hole for the sexnut
screw on the opposite side of the door.
Drill a
1
/
4
" hole (6.8mm)
diameter and 1" (25mm)
deep hole, tap for
M8x1.25 thread.
Drill a
5
/
16
" hole (8mm) diameter hole in
the door for the armature screw and drill
a 1/2
" (12.7mm) diameter and 1" (25mm)
deep hole from the opposite side for the
sexnut screw
Reinforced door Solid-core door Hollow metal door
5
/
8
" (16mm)
5
/
16
" (8mm)
1
/
4
"
(6.8mm) for M
8x1
.25 thread
1
/
2
" (12.7mm)
5
/
16
" (8mm)

SECO-LARM Electromagnetic Locks
SECO-LARM U.S.A., Inc. 5
Installation (Continued)
7. Put a rubber washer between the two
metal washers and place them over the
armature screw between the armature
plate and the armature plate holder. This
allows the plate to pivot around the screw
to compensate for door misalignment.
The rubber washer
is
sandwiched
between the two metal washers
and all three are placed between
the armature plate and the
armature plate holder.
Metal washers
8. Tighten the armature screw enough so that
the armature plate can withstand a break-in
attempt, but loose enough so that the
armature plate can pivot slightly. Make sure
the anti-spin guide pins are in the two guide
pin holes.
Guide pins
Armature screw
TIP
Use a thread-
locking compound
on the armature
screw to ensure a
long-lasting
installation.
Guide pins
9. Screw the two short self-tapping screws through the mounting plate’s slotted holes, but do not
over-tighten them. Keeping them loose will allow for adjustment of the plate so that the long
edge of the mounting plate and the armature plate are parallel. See the diagram below.
Armature plate
Mounting plate
90°
Short self
-
tapping screws
10.
Once the mounting plate position is correct,
use the four long self-tapping screws to
permanently mount the mounting plate.
Long self
-
tapping screws
11. Drill the cable access hole. Run the wiring
through the cable access hole in the
mounting plate and through the hole in the
door frame.

SECO-LARM Electromagnetic Locks
6 SECO-LARM U.S.A., Inc.
Installation (Continued)
12. Remove the cover from the front of the
electromagnet. Run the power leads
through the large cable access hole.
13. Push the electromagnet against the
mounting plate so the electromagnet ends
are flush with the ends of the mounting plate.
Use the Allen wrench to screw the hex-head
mounting screws through the bottom of the
electromagnet into the mounting bracket.
14. Cut the wires so they are long enough to
connect with the terminal block. Set the
voltage using the selection jumpers based
on your input voltage.
NOTES
Failure to
correctly set the input voltage may
cause damage to the lock.
Connect switching devices like push-to-exit
switches between the power source and the
positive terminal on the lock. Connecting
switching devices to the negative terminal
may cause a delay in unlocking.
Position 2 jumpers on
all four pins for 12VDC
operation (default)
Position a jumper on
the two center pins for
24VDC operation
Voltage Selection Jumpers
12
VDC
24
VDC
15. Connect the power and other wires
according to the wiring diagram on page 7.
Test the unit. Then replace the front cover
and install the hex-head tamper caps (x2).
NOTE: This should be the very last step after all
steps are confirmed, since once the
tamper caps are in place, they are very
difficult to remove.

SECO-LARM Electromagnetic Locks
SECO-LARM U.S.A., Inc. 7
Wiring Diagram
NOTES
 Connect switching devices like push-to-exit switches between the power source and the positive
terminal of the lock. Connecting them to the negative terminal may cause a delay in unlocking.
Maximum Distance from Power Source
For a complete chart, visit www.seco-larm.com
12VDC Minimum Wire Gauge
Wire Length 25ft 50ft 75ft 100ft 150ft 200ft 250ft 300ft 400ft 500ft 1,000ft
Wire Gauge@500mA 20 18 18 18 16 14 14 12 10 --- ---
24VDC Minimum Wire Gauge
Wire Length 25ft 50ft 75ft 100ft 150ft 200ft 250ft 300ft 400ft 500ft 1,000ft
Wire Gauge@250mA 22 22 22 20 18 18 16 16 14 14 14
Wiring Diagram
*A fail-safe lock unlocks when power is lost so that, in case of an emergency such as a fire in the building, the fail-safe lock will automatically
unlock allowing personnel to escape quickly.
NOTE: All field wiring must be within the protected area.
Maglock (Fail
-
safe)* (Indoor)
Key Switch
(Outdoor)
N/C Exit Button
(Indoor)
Keypad
(Outdoor)
Access Control
Unit
Control Device
+
–
Power
Supply
12/24 VDC
N.C.
COM
N.O.
–
+
= 12VDC
= 24VDC
Voltage
jumpers
Circuit Board

SECO-LARM Electromagnetic Locks
Troubleshooting
Doors lock, but can easily
be forced open
 Make sure the electromagnet and armature plates are properly
aligned.
 Make sure the contact surfaces of the electromagnet and armature
plates are clean and free from rust.
 Check the power leads with a meter, and make sure 12VDC or
24VDC is present.
 Make sure the rubber washer is installed and free from damage.
Delay in door releasing
 The electromagnet is fitted with a metal oxide varistor to prevent
interference, so do not install a second diode.
 Ensure that the control device is connected between the power
source and the positive terminal of the lock
SECO-LARM
® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PITGW1
MI_E
-
941Sx
-
xxxxxxQ_211025.docx
LIMITED LIFETIME WARRANTY: This SECO-LARM product is warranted aga
inst defects in material and workmanship
while used in normal service for the lifetime of the product. SECO-
LARM’s obligation is limited to the repair or replacement
of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This
Warranty is void if damage is caused
by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal
usage, or faulty installation, or if for any other reason SECO-LARM determines that such equip
ment is not operating properly
as a result of causes other than defects in material and workmanship. The sole obligation of SECO-
LARM and the purchaser’s
exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-
LARM
be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser
or
anyone else. For all other countries, the warranty is 1 (one) year.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-
LARM reserves
the right to change specifications without notice. SECO-
LARM is also not responsible for misprints. All trademarks are the
property off SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2021 SECO-LARM U.S.A.,
Inc. All rights
reserved.
California Proposition 65 Warning: The
se products may contain chemicals which are known to the State of California to
cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
IMPORTANT:
Users and installers of this product are responsible for ensuring that the installation and configuration of this
product complies with all national, state, and local laws and codes. SECO-
LARM will not be held responsible for the use of
this product in violation of any current laws or codes.
IMPORTANT WARNING: Incorrect mounting which leads to exposure to rain or moisture inside the enclosur
e could cause
a dangerous electric shock, damage the device, and void the warranty. Users and installers are responsible for ensuring that
this product is properly installed and sealed.