Seiko DT-40X Parts list manual

Function Operation Guide
Basic Operation
1. Set the power switch (POWER) on the main unit ON.
2. Select the event (F01 to F11) to use by on the infrared remote control.
3. Reset by , and enable by .
4. Set/operate each event.
* Numbers can be fast forwarded by holding down the buttons for at least two seconds during setting/operation.
* The four buzzer sounds and mute can be selected by pressing .
“
Snd1” → “Snd2” → “Snd3” → “Snd4” → “Snd-”
The buzzer sounds for the duration that is held down.
* The display can be switched ON/OFF by pressing .
* Set the channels of the infrared remote control and the main unit. (Total 6 channels)
How to Set the Infrared Remote Control
5. Set the channel of the main unit by .
Each press of switches the display panel “CH 0” → “CH 1” → “CH 2” → “CH 3” → “CH 4” →
“CH 5” → “CH 6” → “CH 0” → “CH 1” and so forth.
* The default setting is “CH 0”. By setting “CH 0”, the remote control can receive all channels.
* This operation cannot be performed while the timer is operating or being set.
6. Set the channel of the infrared remote control by to .
* The default setting is “1”.
* On the infrared remote control body, which channel is currently set cannot be known.
Check operation together with operation of the main unit.
* Before use, be sure to check that the channels of the main unit and infrared remote control are matching.
Clearing Settings
• To clear the settings of the current event, press and then hold down for at least two
seconds.
• To clear the
settings of all events, press and then hold down for at least two seconds.
* This operation cannot be performed while the timer is operating or being set.
F01 Count-Down timer
(max. time setting 99 mins 59 secs, 1 sec or 1/10 sec display, setting of up to 9 warning buzzers)
Operation Procedure Remote Control
Button Operation Display
1. Switch to the setting mode 00:00
2. Enter the time setting (Ex: 10 mins 30 secs)
①Enter minute’s digit, then move to second’s digit 10:00
②Enter second’s digit 10:30
③Apply the time setting, and move to warning buzzer time 1 b00:00 1
3. Enter the warning buzzer time (Ex: 1 min 30 secs)
①Enter minute’s digit, then move to second’s digit b01:00 1
②Enter second’s digit b01:30 1
③Apply the warning buzzer time 1, and move to warning
buzzer time 2 b00:00 2
④If necessary, enter the warning buzzer time 2 and on-
wards by repeating steps ①to ③
When “00:00” is entered for the warning buzzer time,
warning buzzers from then on are canceled, and the
screen returns to the time setting entry screen.
10:30
4. End setting, and switch to the timer mode 10:30
5. Timer start 10:30
6. Change the time (Ex: 6 minutes 17 seconds → 7 min-
utes 32 seconds)
①Timer stop
6:17
②Change minute’s digit Left score 7:17
③Change second’s digit Right score 7:32
7. Timer start (resume) 7:32
8. Match to warning buzzer time 1 1:30
(buzzer)
9. Timer end 0
(buzzer)
10. Return to before start 10:30
* To switch to the setting mode, press to reset the mode, and then press .
*
To enable 1/10 sec display, press while in the setting mode. Pressing this again returns the display to 1 sec display.
F02 Count-Up timer
(max. time setting 99 mins 59 secs, 1 sec or 1/10 sec display, setting of up to 9 warning buzzers)
Operation Procedure Remote Control
Button Operation Display
1. Switch to the setting mode 00:00
2. Enter the time (Ex: 10 mins 30 secs)
①Enter minute’s digit, then move to second’s digit 10:00
②Enter second’s digit 10:30
③Apply the time setting, and move to warning buzzer time 1 b00:00 1
Operation Procedure Remote Control
Button Operation Display
3. Enter the warning buzzer time (Ex: 45 secs)
①Enter minute’s digit, then move to second’s digit b00:00 1
②Enter second’s digit b00:45 1
③Apply the warning buzzer time 1, and move to warning
buzzer time 2 b00:00 2
④If necessary, enter the warning buzzer time 2 and on-
wards by repeating steps ①to ③
When “00:00” is entered for the warning buzzer time,
warning buzzers from then on are canceled, and the
screen returned to the time setting entry screen.
10:30
4. End setting, and switch to the timer mode 0
5. Timer start 0
6. Change the time (Ex: 25 seconds → 20 seconds)
①Timer stop 25
②Change seconds Right score 20
7. Timer start (resume) 20
8. Match to warning buzzer time 1 45
(buzzer)
9. Timer end 10:30
(buzzer)
10. Return to before start 0
* To switch to the setting mode, press to reset the mode, and then press .
* To enable 1/10 sec display, press while in the setting mode. Pressing this again returns the display to 1 sec display.
F03 Stopwatch
(max. measurement time 9 hours 59 mins 59 secs 9, lap/split display switching)
Operation Procedure Remote Control
Button Operation Display
1. Switch the lap/split display
Bottom right●No: Lap
Bottom right●Yes: Split
2. Timer start 0:00 1
3. Timer stop 0:18 5
4. Return to before start 0:00 0
Split time (time elapsed midway)
Operation Procedure Remote Control
Button Operation Display
1. Timer start 0:00 1
2. Split measurement (Ex: 26 mins 13 secs 7) 26:13 7
◀▶ blinks
3. Cancel split 28:32 6
◀▶ goes out
4. Timer stop 220:23 5
5. Return to before start 0:00 0
Lap time (interval time)
Operation Procedure Remote Control
Button Operation Display
1. Timer start 0:00 1
2. 1st lap measurement (Ex: 26 mins 13 secs 7) 26:13 7
◀▶ blinks
3. Cancel 1st lap 28:32 6
◀▶ goes out
4. 2nd lap measurement (Ex: 23 mins 9 secs 2) 23:09 2
◀▶ blinks
5. Cancel 2nd lap 102:21 5
◀▶ goes out
6. Timer stop 220:23 5
7. Return to before start 0:00 0
[Split Time/Lap Time]
Goal
Split 2
Split 1 Split time = time elapsed midway
Lap time = interval time
Start
Lap 1 Lap 2 Lap 3
Split 3
F04 Programmable timer
(max. time setting 99 mins 59 secs, max. 9 program settings, max. setting repeat count 99 times)
Operation Procedure Remote Control
Button Operation Display
1. Switch to the setting mode P00:00 1
2.
Enter program 1 (P1) (Ex: 5 mins 30 secs)
①Enter minute’s digit, then move to second’s digit P05:00 1
②Enter second’s digit P05:30 1
③Apply program 1 (P1), and move to program 2 (P2) P00:00 2
3.
Enter program 2 (P2) (Ex: 3 mins 20 secs)
①Enter minute’s digit, then move to second’s digit P03:00 2
②Enter second’s digit P03:20 2
③Apply program 2 (P2), and move to program 3 (P3) P00:00 3

Operation Procedure Remote Control
Button Operation Display
④If necessary, enter program 3 (P3) and onwards by
repeating steps ①to ③.
When “00:00” is entered for the program setting,
programs from then on are canceled, and the screen
returns to the repeat count entry screen.
0
4. ①Enter the repeat count (Ex: 15 times) 15
②
Apply the repeat count
P05:30 1
5. End setting, and switch to the timer mode 5:30 1
6. Timer start
The buzzer sounds and P1 starts
5:30 1
(buzzer)
7. When P1 ends, the buzzer continues to sound and P2
starts
3:20 1
(buzzer)
8. Change the time (Ex: 1 minute 20 seconds →3 minutes
10 seconds)
①Timer stop
1:20 2
②Change minute’s digit Left score 3:20 2
③Change second’s digit Right score 3:10 2
9. Timer start (resume) 3:10 2
10. Check the repeat count (Ex: P2 at 13th repeat count)
①Display the repeat count
13 P2
◀▶ blinks
(This is hidden when the timer
has stopped.)
②Return to timer display 3:05 2
◀▶ goes out
11. End all programs 0 2
(buzzer)
12. Return to before start 5:30 1
* To switch to the setting mode, press to reset the mode, and then press .
* To switch the timer to the countup mode, press while in the setting mode.
During countup, ●at the bottom left lights. Press this again to return to the countdown mode.
*
To end program execution without performing the last program, press while in the timer mode, and light ●at the
bottom right.
F05 Clock & Alarm
(12-/24-hour clock, max. 5 alarm settings)
Operation Procedure Remote Control
Button Operation Display
1. Switch to the setting mode b--:-- 1
2. Enter alarm time 1 (Ex: 14 hours 55 mins)
①Enter hour’s digit, then move to minute’s digit b14:-- 1
②Enter minute’s digit b14:55 1
③Apply the alarm time 1, and move to alarm time 2 b--:-- 2
3. Enter alarm time 2 (Ex: 18 hours 30 mins)
①Enter hour’s digit, then move to minute’s digit b18:-- 2
②Enter minute’s digit b18:30 2
③Apply the alarm time 2, and move to alarm time 3 b--:-- 3
④If necessary, enter the alarm time 3 and onwards by
repeating steps ①to ③.
*When applying a setting without entering the alarm
time, the screen moves to the current time entry screen.
--:--
4. Enter the current time (Ex: 13 hours 10 mins)
①Enter hour’s digit, then move to minute’s digit 13:--
②Enter minute’s digit 13:10
③Apply the current time b14:55 1
5. End setting, and switch to the clock mode 13:10 0
6. Clock start
The time is displayed as seconds for the first five seconds
13:10 1
* To switch to the setting mode, press to stop the clock (0 seconds is displayed and time stops), and press .
* To change the 12/24 clock system and the lit/blinking display of the colon, press while in the clock mode.
The display switches in the following order: “24-hour clock/colon lit” →“24-hour clock/colon blinks” →“12-hour clock/colon
lit” →“12-hour clock/colon blinks”. After one second, the screen automatically returns to the current time (clock display).
* To set 0 seconds, press .
When seconds are 0 to 29 seconds (Ex: 11 hours 22 mins 28 secs), the time changes to 11 hours 22 minutes 0 seconds.
When seconds are 30 to 59 seconds (Ex: 11 hours 22 mins 49 secs), the time changes to 11 hours 23 minutes 0 seconds.
* When not entering the alarm time, press and move to the current time entry screen.
F06 Score
(Score: max. display 99 vs 99, scored set/scored game: max. display 9 vs 9)
Operation Procedure Remote Control
Button Operation Display
1. Enter the score for the left team (Ex: 12 vs 0) Left score 012- 0 0
2. Enter the score for the right team (Ex: 12 vs 5) Right score 012- 5 0
3. Enter the right to serve for the left team 012- 5 0
◀lights
4. Enter the right to serve for the right team 012- 5 0
▶lights
5. Enter the time-out for the left team 012- 5 0
●at the bottom left
lights
6. Enter the time-out for the right team 012- 5 0
●at the bottom right
lights
7. Enter the set for the left team (Ex: 2 vs 0) Left sets 012- 5 0
8. Enter the set for the right team (Ex: 2 vs 3) Right sets 212- 5 3
9. Change court 35-12 2
Operation Procedure Remote Control
Button Operation Display
10. Move to next set
Reset display except number of sets 30- 0 2
11. Reset all displays Hold down for
2 seconds 00- 0 0
* To hide the number of scored sets/scored games, enter the setting mode by and press .
Pressing again returns the mode to the score mode.
F07 Game mode (Count-Down)
* You can switch the display between the timer and score.
For details on game time operations, see “F01 Count-Down timer.”
For details on score operations, see “F06 Score.”
* To switch between game time setting and score setting, press while in the setting mode.
* To switch between score display and game time display, press while in the game mode.
F08 Game mode (Count-Up)
* You can switch the display between the timer and score.
For details on game time operations, see “F02 Count-Up timer.”
For details on score operations, see “F06 Score.”
* To switch between game time setting and score setting, press while in the setting mode.
* To switch between score display and game time display, press while in the game mode.
F09 Tennis
(Score: 0/15/30/45/A, scored game: 0 to 9, score at tie-break: 0 to 99)
Operation Procedure Remote Control
Button Operation Display
1. Enter the score for the left player (Ex: 15 vs 0) Left score 015- 0 0
2. Enter the score for the right player (Ex: 15 vs 40) Right score 015-40 0
3.
Left player scores, score is now deuce
Left score 040-40 0
4.
Right player scores, score is now advantage
Right score 0- A 0
5. Enter the right to serve for the left player 030-40 0
◀lights
6. Enter the right to serve for the right player 030-40 0
▶lights
7. Enter the game of the left player (Ex: 2 vs 0) Left sets 230-40 0
8. Enter the game of the right player (Ex: 2 vs 3) Right sets 230-40 3
9. Change court 340-30 2
10. Move to next game
Reset display except number of games 30- 0 2
11. Reset all displays Hold down for
2 seconds 00- 0 0
* To switch to tie-break, press to light ●at the bottom left and right.
F10 4 digits number display
* You can display 4-digit numbers. (max. display 9999)
Operation Procedure Remote Control
Button Operation Display
1. Enter the 1’s and 10’s digit number (Ex: 185)
Left score
85
1. Enter the 100’s and 1000’s digit number
*”0” is not displayed.
Right score
1 85
3. Reset all number values 0
F11 Remaining date display
(Time setting 1 min to 9998 days 23 hours 59 mins)
Operation Procedure Remote Control
Button Operation Display
1. Switch to the setting mode. 00 00
2. Enter the remaining number of days. (Ex: 123 days
16 hours 45 mins)
①Enter 100 day’s digit, then move to 1 day’s digit
1 00
②Enter 1 day’s digit 1 23
③Apply the remaining number of days, and move to
remaining time 00:00
3. Enter the remaining hours (Ex: 123 days 16 hours
45 mins)
①Enter hour’s digit, then move to minute’s digit
16:00
②Enter minute’s digit 16:45
③Apply the remaining time 01 23
4. End setting, and start countdown 1 24
(Blinks 3 times)
5. Remaining number of days 0 (end of countdown) 0
* To change the remaining number of days and remaining time, press to switch to the setting mode and enter the de-
sired number of days and remaining time.
I-7358-1
*For more information about the operation, visit the website.
(https://www.seiko-sts.co.jp).