Sencor STM 6359BK User manual

04/2021
- 1 -
Copyright © 2021, Fast ČR, a.s.
EN Food Processor
STM 6359 BK

04/2021
- 2 -
Copyright © 2021, Fast ČR, a.s.
EN Food Processor
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
■This appliance may be used by persons with physical or mental impairments
or by inexperienced persons, if they are properly supervised or have been
informed about how to use the appliance in asafe manner and understand
the potential dangers.
■Children must not use this appliance or play with it. Keep this appliance
and the power cord out of reach of children.
■Before connecting this appliance to apower socket, make sure the rated
voltage stated on its rating label corresponds to the voltage in your power
socket.
■Never use accessories, which have not been supplied with this appliance or
which have not been explicitly recommended by the manufacturer for this
type of appliance.
■This appliance is designed for household use. Do not use it for commercial
purposes, in industrial surroundings, or outdoors, or for purposes other
than those for which it is intended.
■Always place the appliance on an even, dry and stable surface. Do not place
it on an electric or gas stove, in the vicinity of an open ame or appliances
that are sources of heat.
Do not put your hands into an area marked by this symbol. Otherwise
injury could result when the multi-function head is tilted out and is
not properly locked in the top position.
■Never use multiple attachments at the same time.
■Before putting the appliance into operation, check that it is correctly
assembled and that the multi-function head is tilted down in the horizontal
position. For safety reasons, this appliance is equipped with a safety
mechanism that prevents the motor from being started when the multi-
function head is tilted out.

04/2021
- 3 -
Copyright © 2021, Fast ČR, a.s.
■In the event that the multi-function head tilts out during operation, the
appliance will automatically stop running. When the multi-function
head is tilted to the horizontal working position, the appliance will not
automatically resume operation. To resume operation, it is necessary to set
the speed control knob to the OFF position and then re-select the desired
speed.
■Do not touch rotating parts of the appliance and ensure that foreign items
such as clothing, hair, etc. are kept away. An injury could occur or the
appliance could be damaged.
■In the event that an item, such as a spoon, falls into the bowl during
operation, immediately set the speed control knob to the OFF position
(stand-by mode), and disconnect the power cord from the power socket.
Wait until the rotating parts come to astop and then remove the item.
■If ingredients stick to the attachment or the sides of the bowl, turn the
appliance o, disconnect it from the power socket, and wait until the
rotating parts come to astop. Use asilicone spatula to clean the attachment
and the inside of the bowl. Then you can restart the appliance.
■Make sure that no hair, clothing or other items enter the feed tube of meat
grinder while it is running. Do not put anything other than the ingredients
that are to be processed into the feed tube.
■Never use your ngers or other items to push ingredients through the
meat grinder feed tube. For this purpose there is apusher included as an
accessory.
Warning:
Incorrect use may lead to injuries.
■To prevent injury caused by sharp edges, be especially careful when
handling the grinding blade of the meat grinder and the blade assembly
of the blender. Increased attention must also be paid when emptying out
the blending jar, when removing the blade assembly from the blending jar,
when removing the grinding blade from the chamber, and when cleaning
the appliance.
■Do not attempt to grind bones, nut shells or other hard ingredients.

04/2021
- 4 -
Copyright © 2021, Fast ČR, a.s.
■Hot liquids up to a temperature of 55 °C may be processed in the
blending jar. Be especially careful when handling hot liquids. Hot steam or
splashing hot foods and liquids may cause scalding. Never start the blender
without the lid properly seated in position.When processing hot liquids, do
not remove the inner cap during operation. Do not touch the hot surface.
Use the handle to carry the blending jar when it is hot.
■The maximum continuous operating time is 10 minutes. Do not exceed
the maximum operating time of 5 minutes when in the kneading mode
and do not exceed the maximum operating time of 2 minutes when using
the blender. Before starting it again, allow the appliance to cool down for
30 minutes.
■Always turn o the appliance, disconnect it from the power socket when
not be using it, when leaving it without supervision, and before assembling,
disassembling, cleaning or moving it. Prior to disassembling the appliance
and replacing accessories or accessible parts that move during use, wait
until all moving parts come to astop.
■Clean it according to the instructions in chapter Cleaning and maintenance.
■Never wash the appliance under running water or submerge it in water or
another liquid.
■Do not turn on the appliance when it is empty. Incorrect use of the appliance
may negatively aect its lifetime.
■Ensure that the power plug contacts do not come into contact with water
or moisture. Do not place heavy items on the power cord. Make sure that
the power cord does not hang over the edge of atable or that it is not
touching ahot surface.
■Disconnect the power cord from the power socket by pulling on the plug,
never pulling on the cord. Otherwise, this could damage the power cord or
the socket.
■If the power cord is damaged, have it replaced at aprofessional service
centre. It is forbidden to use the appliance if it has adamaged power cord.
■To avoid the danger of injury by electrical shock, do not repair the appliance
yourself or make any adjustments to it. Have all repairs performed at an
authorised service centre. By tampering with the appliance, you risk
voiding your legal rights arising from unsatisfactory performance or quality
warranty.

04/2021
- 5 -
Copyright © 2021, Fast ČR, a.s.
A
1
2
3
11
10
9
7
6
12
14
8
15
4
513

04/2021
- 6 -
Copyright © 2021, Fast ČR, a.s.
B
1
2
3
4
5
6
7
8
9
14
13
12
11
10
15
16
C1
3
2
4
5
6

04/2021
- 7 -
Copyright © 2021, Fast ČR, a.s.
EN Food Processor
User'smanual
■ Prior to using this appliance, please read the user’smanual thoroughly, even if you already
have experience in using similar appliances. Only use the appliance in the manner described
in this user’smanual. Keep this user’smanual in asafe place where it can be easily retrieved
for future use.
■ We recommend saving the original cardboard box, packaging material, purchase receipt
and responsibility statement of the vendor or warranty card for at least the duration of the
legal liability for unsatisfactory performance or quality. In the event of transportation, we
recommend that you pack the appliance in the original box from the manufacturer.
DESCRIPTION OF THE APPLIANCE AND ACCESSORIES
A1 Button for releasing the meat grinder
from the front attachment hub
A2 Removable cover of the front meat
grinder attachment hub
A3 A-shaped beater
A4 Balloon whisk
A5 Kneading hook
A6 Removable cover of the top blender
attachment hub
A7 Tilt-out multi-function head
A8 Attachment hub for mounting
attachments A3–A5
A9 Bowl cover with ahole for adding
ingredients
A10 4.5-litre stainless steel bowl
A11 Base unit
A12 Speed control knob
Serves to gradually set the speed level
MIN-1-2-3-4-5-6-MAX, set the pulse
level (PULSE) and to turning off the
appliance (OFF).
A13 Multi-function head release lock
A14 Anti-slip feet for stability of the
appliance during operation
A15 Lid
serves to close the stainless steel bowl
A10 for short term storage of processed
ingredients.
DESCRIPTION OF MEAT GRINDER ACCESSORIES
B1 Pusher
B2 Stainless steel hopper
B3 Feed tube
B4 Grinding chamber
B5 Screw shaft
B6 Grinding blade
B7 Screw ring
B8 Fine grinding plate
B9 Medium fine grinding plate
B10 Coarse grinding plate
B11 Separator
B12 Sausage stuffer attachment
B13 Moulder
B14 Conical attachment
B15 Cookie maker
B16 Cookie maker holder
Note:
Parts B11–B14 are contained inside the pusher B1.
Certain models are only equipped with ane and coarse grinding disc B8
and B10.
DESCRIPTION OF THE BLENDER ACCESSORIES
C1 Inner cap of the blending jar
C2 Outer lid of the blending jar with ahole
for adding ingredients
C3 Handle
C4 Glass blending jar with 1.5l capacity
C5 Cu
C6 Blade assembly
BEFORE FIRST USE
1. Take the appliance and its accessories out of the packaging materials.
2. Thoroughly wash all accessory parts that are intended to come into contact with food using
warm water and aneutral kitchen detergent. Then rinse under clean running water and
thoroughly wipe dry with ane wiping cloth or allow them to dry naturally. After washing
and drying, we recommend to coat the grinding blade B6 and the grinding plates B8–B10
with cooking oil.
3. Do not submerge the food processor or its power cord in water or any other liquids.
Attention:
The metal parts of the meat grinder and attachments A3–A5 are not
intended for washing in a dishwasher. Other removable parts may be
washed in adishwasher.
BEATING, WHIPPING AND KNEADING
SELECTING ATTACHMENT TYPES
Attachment type Purpose of use
Beater A3 It is used for beating light and medium heavy yeast-free doughs,
for preparing sauces, creams, llings, etc. Do not use it for
kneading heavy doughs.
Balloon whisk A4 It is used for whisking whole eggs or egg whites, whipped
cream, foamy creams, etc. Do not use it for beating or
kneading doughs.
Kneading hook A5 It is used for kneading various types of doughs including heavy
and thick doughs such as for example bread dough, pizza
dough, fresh pastry doughs, etc.
ASSEMBLING AND DISASSEMBLING THE FOOD PROCESSOR
■ Before you start assembling or disassembling the food processor, check that it is turned o
and disconnected from the el. power socket.
1. Inserting the bowl and attaching the cover
1.1 Place the food processor on an even, dry and stable surface, for example on a kitchen
countertop.
1.2 Use the lock A13 to release the multi-function head A7 and tilt it out all the way. After tilting
out the multi-function head A7 release the lock A13. Locking of the multi-function head A7
inthe top open position is indicated by the lock A13 returning to the default position, which
is accompanied by an audible click.
1.3 Insert the stainless steel bowl A10 into the base unit A11 and secure it in place by turning it
clockwise. When the bowl A10 is properly attached, it cannot be separately lifted out of the
base unit A11.
1.4 On to the bottom part of the multi-function head A7 with attachment hub A8, slide the
cover A9 so that the latches along the perimeter of the round opening in the cover A9 slide
into the grooves along the perimeter of the attachment hub A8.
1.5 The lid A15 is used for covering the bowl A10 for short term storage of processed
ingredients.
2. Mounting attachments
2.1 When attaching an attachment, the multi-function head A7 must be locked in the open
position, see point 1.2 in the previous chapter. To attachment hub A8, attach one of
the attachments A3–A5 in such away that the attachment hub shaft A8 slides into the
attachment. Push the attachment towards the attachment hub A8 and turn it anticlockwise
to secure it in place. Lightly pull the attachment downwards with one hand to check that it
is properly attached.
2.2 Place the ingredients that you wish to process into the bowl A10. Release the lock A13 and
tilt the multi-function head A7 to ahorizontal position. After tilting down the multi-function
head A7, release the lock A13. The locked status of the multi-function head A7 in the tilted
down work position is indicated by the lock A13 returning to the default position. This is
accompanied by an audible click.
3. Disassembly
3.1 Use the lock A13 to release the multi-function head A7 and tilt it out all the way. After tilting
out the multi-function head A7, release the lock A13. Locking of the multi-function head A7
inthe top open position is indicated by the lock A13 returning to the default position, which
is accompanied by an audible click.
3.2 Push the attachment towards the attachment hubA8 and turn it clockwise to release it,
and then remove it. Turn the bowl A10 anticlockwise and remove it from the base unit A11.
Remove the cover A9 by pulling it downwards. Move the multi-function head A7 back to the
horizontal position.
USING THE FOOD PROCESSOR
1. Select the right type of attachment based on its intended use and assemble the appliance
according to the instructions in the chapter Assembling and disassembling the appliance.
Place the ingredients into the bowl A10.
Attention:
In asingle batch, it is possible to precess no more than 2.2 litres of light dough or
0.8 litres of thick, heavy dough. The maximum number of egg whites that can be
whisked at once is 12. We recommend that you do not ll the bowl A10 past the level
of the 3l mark. If an insucient amount of ingredients are put in the bowl A10 (less
than 0.3 litres of dough), then they may not be optimally processed.
2. Make sure that the multi-function head A7 is tilted down in the horizontal working position
and that the speed control knob A12 is set to the OFF position. Connect the power cord to
apower socket.
3. Set the required speed using the speed control knob A12. Gradually turn the speed control
knob A12 clockwise to increase the speed, turning it in the opposite direction will reduce
the speed. To initially stir in the ingredients, rst set alower speed and then adjust it as
required. Electronic speed regulation ensures that the set speed will be maintained under
various loads. While it is running, ingredients may be added into the bowl A10 through the
hole in the cover A9.
4. The pulse mode is used for increasing the speed to maximum for ashort time. To activate
the pulse mode, turn the speed control knob A12 to the PULSE position and to ensure
continuous operation hold it down in this position. As soon as you release the speed control
knob A12, it will automatically return to the OFF position.
5. If it is necessary to wipe ingredients o the inside of the mixing bowl A10 and the
attachment, rst turn o the food processor by setting the speed control knob A12 to the
OFF position and then disconnect it from the power socket. Wait until the rotating parts
come to astop and only then scrape away the ingredients with aspatula.
6. After you have nished using the appliance, set the speed control knob A12 to the OFF
position and disconnect the power cord from the power socket.
7. Wait until the rotating parts come to astop and disassemble the food mixer according to
the instructions included in chapter Assembling and disassembling the appliance. Use asoft
plastic spatula to empty out the contents of the bowl A10.
8. Clean out the food processor after each use according to the instructions in chapter
Cleaning and maintenance.
LED LIGHT
■ The multi-function head A7 has a LED light that turns on automatically when the food
processor is connected to a power socket. The LED light turns o automatically after
2.5 minutes of inactivity, i.e. when the appliance is not running or when the speed is not set
during this time. The LED light turns on again automatically when the food processor is put
into operation by the control knob A12 being set to a desired speed level.

04/2021
- 8 -
Copyright © 2021, Fast ČR, a.s.
QUICK GUIDE TO PROCESSING INGREDIENTS
Attachment type Ingredients Maximum
load
Processing
time
Speed
selection
Balloon whisk A4 Egg whites 12 pcs 4 min 5–6
Balloon whisk A4 Whipping cream 1l 6–8 min 5–6
Beater A3 Cake dough 2.2l 6 min 3–4
Kneading hook A5 Bread dough
Pizza dough
0.8l 4–5 min MIN to 2
Note:
The above processing times are only areference.
When whipping egg whites, the bowl A10 and the beater A4 must be
perfectly clean and dry. Even asmall amount of fat may cause the egg whites
not be whipped to the desired snowy consistency.
Whipping cream should be cooled to atemperature of 6 °C prior to being
whipped.
Prior to processing them, allow the ingredients used for making various
doughs to rest at room temperature.
GRINDING MEAT, MAKING SAUSAGES AND KEBABS, AND
MAKING COOKIES
ASSEMBLING AND DISASSEMBLING THE MEAT GRINDER
1. Insert the screw shaft B5 into the grinding chamber B4 with the cogged wheel entering rst.
2. Place the grinding blade B6 on to the shaft B5 (with the edge facing outwards from the
chamber) and on to it attach agrinding plate B8, B9 or B10 depending on the preferred
the grind. Make sure that the notch in the grinding chamber B4 slides into the groove in the
grinding plate.
Attention:
When attaching the blade B6, be very careful not to injure yourself on the
sharp edge.
3. Place the screw ring B7 on to the grinding chamber B4 and tighten it securely by screwing
it clockwise. Place the stainless steel hopper B2 on to the feed tube B3.
4. Make sure that the food processor is turned o and disconnected from the power socket.
The multi-function head A7 must be tilted down in the horizontal position and the whisk,
beater or kneading attachments must be removed. Remove the front cover A2 from the
multi-function head A7. Place the assembled attachment against the attachment hub
so that the feed tube B3 is tilted to the right at an angle of approximately 45° from the
vertical axis and secure the attachment in vertical position by turning it anticlockwise.
The attachment is locked in place when the button A1 slides out. This is accompanied by an
audible click.
5. When disassembling the meat grinder, rst remove the hopper B2. Then press the button
A1 and remove the meat grinder by turning it clockwise. After removing the grinder, put the
cover A2 back in its place.
6. When disassembling the meat grinder into its individual parts, proceed in the reverse
sequence.
USING THE MEAT GRINDER
1. First prepare the meat for grinding in the following way. Remove all bones, tendons,
cartilage and cut the meat into
2 × 2 × 6 cm size pieces that will freely pass through the feed
tube B3.
Attention:
Do not process frozen meat. Allow it to defrost before grinding it.
2. Make sure that the food processor is correctly assembled and that the speed control knob
A12 is set to the OFF position.
3. Place the bowl A10 or another suitable container under the meat grinder. Insert the power
plug into apower socket.
4. Use the speed control knob to set the desired speed. We recommend to initially set speed
3 and then increase it as required. Gradually place the meat pieces into the feed tube B3
and push them in using the pusher B1. Take care not to clog up the feed tube B3 by alarge
amount of meat. Do not process more than 5 kg of meat per batch. The processing time is
only several minutes.
Attention:
Do not use ngers or other items to push the meat in. Always use the pusher
B1 designed for this purpose.
5. The ground meat will fall into the prepared bowl. The meat that remains in the grinding
chamber B4 can be removed by grinding aslice of bread or abread roll.
6. To turn o the food processor, set the speed control knob A12 to the OFF position.
7. Clean out the meat grinder after each use according to the instructions in chapter Cleaning
and maintenance.
ASSEMBLING AND DISASSEMBLING THE SAUSAGE STUFFER ATTACHMENT
1. Proceed in the same way as when assembling the meat grinder, only with the dierence that
instead of the grinding blade B6 and the grinding plate B8, B9 or B10, only parts B11 aB12
are used.
2. Place the separator B11 on to the screw shaft so that the notch in the grinding chamber B4
ts into the groove in the separator B11. Place the sausage stuer attachment B12 on to the
separator B11 and complete the entire sausage stuer assembly by screwing the screw ring
B7 on to the grinding chamber B4. Place the stainless steel hopper B2 on to the feed tube
B3.
3. Attach the attachment to the food processor in the same way as described in point 4 in
chapter Assembling and disassembling the meat grinder.
4. When disassembling, rst remove the hopper B2. Then press the button A1 and remove the
attachment by turning it clockwise. After removing the attachment, put the cover A2 back
in its place.
5. When disassembling the attachment into its individual parts, proceed in the reverse
sequence.
USING THE SAUSAGE STUFFER ATTACHMENT
1. Make sure that the food processor is correctly assembled and that the speed control knob
A12 is set to the OFF position. Insert the power plug into apower socket.
2. Prepare a sausage casing that you will stu with ground meat and allow it to soak in
lukewarm water for approx. 10 minutes. Place the ground meat mixture on to the hopper
B2. Take the sausage casing out of the water and skewer or tie up one end and slide the
other end like asock on to the sausage stuer attachment B12.
3. Use the speed control knob A12 to set the desired speed. We recommend to initially set
the lowest speed and then increase it as required. With one hand hold the sausage casing
on the attachment B12 and use the other hand to push the ground meat mixture with the
pusher B1 through the feed tube B3. If the sausage casing sticks to the attachment B12, it is
necessary to moisten it with water again.
Attention:
Do not use ngers or other items to push the ground meat in. Always use the
pusher B1 designed for this purpose.
4. To turn o the appliance, set the speed control knob A12 to the OFF position.
5. Clean out the individual parts of the attachment after each use according to the instructions
in chapter Cleaning and maintenance.
ASSEMBLING AND DISASSEMBLING THE KEBAB MAKER ATTACHMENT
1. Proceed in the same way as when assembling the meat grinder, only with the dierence that
instead of the grinding blade B6 and the grinding plate B8, B9 or B10, only parts B13 aB14
are used.
2. Place the moulder B13 on to the screw shaft B5 so that the notch in the grinding chamber
B4 ts into the groove in the moulder B13. Place the kebab moulder attachment B13 on to
the conical attachment B14 and complete the entire kebab maker assembly by screwing the
screw ring B7 on to the grinding chamber B4. Place the stainless steel hopper B2 on to the
feed tube B3.
3. Attach the attachment to the food processor in the same way as described in point 4 in
chapter Assembling and disassembling the meat grinder.
4. When disassembling, rst remove the hopper B2. Then press the button A1 and remove the
attachment by turning it clockwise. After removing the attachment, put the cover A2 back
in its place.
5. When disassembling the attachment into its individual parts, proceed in the reverse
sequence.
USING THE KEBAB MAKER ATTACHMENT
1. Make sure that the food processor is correctly assembled and that the speed control knob
A12 is set to the OFF position. Insert the power plug into apower socket.
2. Place the prepared kebab meat mixture on to the hopper B2. Use the speed control knob
A12 to set the desired speed. We recommend to initially set the lowest speed and then
increase it as required. Using the pusher B1, push the mixture through the feed tube B3.
The result will be ahollow meat tube that is then cut into smaller pieces. The kebab is
atraditional meal from the Middle East made predominantly from ground meat and whole
grain wheat.
Attention:
Do not use ngers or other items to push the ground meat in. Always use the
pusher B1 designed for this purpose.
3. To turn o the appliance, set the speed control knob A12 to the OFF position.
4. Clean out the individual parts of the attachment after each use according to the instructions
in chapter Cleaning and maintenance.
ASSEMBLING AND DISASSEMBLING THE COOKIE MAKER ATTACHMENT
1. Proceed in the same way as when assembling the meat grinder, only with the dierence that
instead of the grinding blade B6 and the grinding plate B8, B9 or B10 only parts B11,B15
and B16 are used.
2. Place the separator B11 on to the screw shaft so that the notch in the grinding chamber B4
ts into the groove in the separator B11. Insert the cookie maker holder B16 into the screw
ring B7. Screw the screw ring B7 clockwise on to the grinding chamber B4. Complete the
assembly by inserting the cookie maker B15 into the holder B16 and attaching the hopper
B2 to the feed tube B3.
3. Attach the attachment to the food processor in the same way as described in point 4 in
chapter Assembling and disassembling the meat grinder.
4. When disassembling, rst remove the hopper B2. Then press the button A1 and remove the
attachment by turning it clockwise. After removing the attachment, put the cover A2 back
in its place.
5. When disassembling the attachment into its individual parts, proceed in the reverse
sequence.

04/2021
- 9 -
Copyright © 2021, Fast ČR, a.s.
USING THE COOKIE MAKER ATTACHMENT
1. Place the prepared dough on to the hopper B2. Slide the cookie maker B15 to the left or
right to set the desired cookie shape.
2. Insert the power plug into apower socket. Set the required speed using the speed control
knob A12. When starting it for the rst time, we recommend that you set speed 3 and then
increase or decrease it as required.
3. Use the pusher B1 to push the dough through the feed tube B3. The food processor will
push the dough out in the required shape that you set using the cookie maker B15.
We recommend that you place atray or your palm underneath the pushed out dough. Then
cut the formed dough into smaller pieces.
Attention:
Do not use ngers or other items to push the dough in. Always use the
pusher B1.
4. When you have nished using the food processor, turn it o by setting the speed control
knob A12 to the OFF position.
5. Clean out the attachment after each use according to the instructions in chapter Cleaning
and maintenance.
BLENDING
ASSEMBLING AND DISASSEMBLING THE BLENDER
1. On to the blending jar C4, place the outer lid C2 so that its edges copy the neck of the jar,
and push it down thoroughly along its entire perimeter. Into the hole in the lid C2, place the
inner cap C1 and push it down all the way.
2. Make sure that the food processor is turned o and disconnected from the power socket.
The multi-function head A7 must be tilted down in the horizontal position and the whisk,
beater or kneading attachments must be removed. Release and remove the top attachment
hub cover A6. Place the assembled blending jar on to the top hub and pulling it gently
turn it in the direction of the symbol all the way. The safety mechanism will prevent the
blender from starting unless it is correctly secured to the multi-function head A7.
3. To disassemble proceed in the reverse sequence.
USING THE BLENDER
1. The blender is intended for preparing meals and drinks such as milkshakes, creamy soups,
sauces, spreads, fresh baby foods, etc. It is not intended for juicing fruit and vegetables,
preparing potato purée, yeast dough or for whipping egg whites.
2. Assemble the blender according to the instructions in chapter Assembling and
disassembling the blender, and put the ingredients (larger pieces need to be cut up in
advance) into the blending jar C4.
Note:
The maximum capacity of the blending jar C4 is 1.5 litres. Never ll it past
the maximum mark. When processing hot liquids or liquids that expand in
volume during the blending process, it is recommended to ll the blending
jar to no more than ⅔ of its maximum capacity.
3. Make sure that the food processor is correctly assembled and that the speed control knob
A12 is set to the OFF position. Connect the power cord to apower socket. Set the required
speed using the speed control knob A12. We recommend to rst set aslower speed to
allow the ingredients to mix together. Then the speed may be increased. The pulse level
is appropriate when you wish to blend food only very quickly. To start the pulse level, turn
the speed control knob A12 to the PULSE position and hold it in this position for amoment.
As soon as you release the speed control knob A12, it will automatically return to the OFF
position.
Attention:
Hot liquids up to atemperature of 55 °C may be processed in the blending
jar. The maximum operating time of the blender is 2 minutes. Do not leave
the appliance in continuous operation for longer than indicated above. Then
allow it to cool down for 30 minutes.
4. While blending, you may add food or liquids to the blending jar C4 through the hole in the
lid C2 after removing the inner cap C1. Never open the outer lid C2 during operation. When
processing hot liquids, the inner cap C1 must remain closed.
5. In the event that food is sticking to the blade assembly C6 or the walls of the blending jar
C4, turn the appliance o by turning the speed control knob A12 to the OFF position and
disconnect it from the power socket. Make sure that the blade assembly C6 has stopped
rotating. Carefully remove the assembled blending jar from the multi-function head A7 by
turning it in the direction of the symbol . Take o the lid and using a plastic spatula,
clean the blade assembly C6 and the inside of the blending jar C4. Put the lid back on and
reattach the blender assembly to the multi-function head A7. Plug the power cord into
apower socket and continue blending.
6. After you have nished using the appliance, set the speed control knob A12 to the OFF
position and disconnect the power cord from the power socket. Check that the blade
assembly C6 has stopped rotating and carefully take the blending jar assembly o the multi-
function head A7. Put the cover A6 back in its place and use asoft plastic spatula to remove
food from the blending jar C4.
7. Disassemble the assembled bowl and clean the individual parts after each use according to
the instructions in chapter Cleaning and maintenance.
ADVICE AND TIPS FOR BLENDING
■ First cut food with a rm consistency such as fruit and vegetables into smaller pieces
measuring 3 cm and only then blend it.
■ First, blend a smaller amount of ingredients and then gradually add more ingredients
through the hole in the lid C2 while blending. In this way, you will achieve better results
than by adding all ingredients into the blending jar C4 at once.
■ If you need to blend food of asolid consistency together with liquids, we recommend that
you rst blend the food of solid consistency and apart of the liquids.Then gradually add the
remaining liquids through the hole in the lid C2 while blending.
■ To blend very thick liquids, we recommend using the pulse level so that the blade assembly
C6 does not get jammed too often. Start the blender repeatedly in short intervals.
■ Ice cubes must be processed immediately upon being removed from the freezer. When the
ice starts to melt, the ice cubes will stick together and it will not be possible to blend them.
QUICK GUIDE TO PROCESSING INGREDIENTS
Ingredients Speed selection Recommended
blending time
Fruit, vegetables cut into smaller pieces 5–6 30 s
Baby food 5–6 40 s
Spreads, dressings, marinades 3–4 30 s
Smoothies and cocktails 6 to MAX 40 s
Soups 6 to MAX 30 s
Ice cubes PULSE
Note:
The above food processing times are only areference. The actual blending
time depends on the size of the ingredients, their amount and the required
nal consistency.
CLEANING AND MAINTENANCE
■ Before cleaning the food processor, always switch it o by setting the speed control knob
A12 to the OFF position and disconnect it from the power socket.
■ Disassemble the food processor into its individual parts. Wait until moving parts come to
acomplete stop before disassembly.
■ Thoroughly wash the used removable parts after every use using warm water with aneutral
dishwashing detergent.Then rinse them under clean running water and wipe them dry with
ane wiping cloth or allow them to dry naturally. After washing and drying, we recommend
to coat the grinding blade B6 and the grinding plates B8, B9 andB10 with cooking oil.
■ If you whisked egg whites, rst rinse the bowl A10 and the beater A4 under cold water.
If you were to use hot water, the egg white remains would harden and their removal would
be more dicult.
■ Clean the mixing container C4 by lling it with 0.5 litre of clean water and afew drops of
kitchen detergent and then assemble the blender and run it for 10 to 15 seconds. Then turn
o the food processor, disconnect it from the power socket, and after the rotating parts have
come to astop, remove the blending jar assembly. Empty out the contents of the blending
jar C4 and then thoroughly rinse out the blending jar C4 with clean water and wipe dry.
■ If more thorough cleaning is required, the cu C5 with blade assembly C6 may be removed
using aspecial wrench that can be ordered free of charge at an authorised service centre.
After cleaning, it is necessary to install the cu C5 with blade assembly C6 back in its place
and to properly tighten it using the wrench.
Attention:
When cleaning, be very careful not to injure yourself on the sharp cutting edge.
■ The metal parts of the meat grinder, the blade assembly C6 and attachments A3–A5
are not intended for washing in adishwasher. Other removable parts may be washed in
adishwasher.
■ For cleaning the base unit A11 and the multi-function head A7, use acloth lightly dipped
in a weak detergent solution. Then wipe everything with a clean dampened cloth and
thoroughly wipe dry.
■ For cleaning, do not use solvents or cleaning agents with abrasive eects. Otherwise, the
surface of the appliance may be damaged.
■ Do not submerge the food processor or its power cord in water or any other liquids.
STORAGE
■ When not using the food processor, store it in a clean, dry place out of children’s reach.
Make sure that the multi-function head A7 is tilted down into the horizontal position.
TECHNICAL SPECIFICATIONS
Rated voltage range............................................................................................................................... 220−240 V
Rated frequency...........................................................................................................................................50/60 Hz
Rated power input........................................................................................................................................1 000 W
Noise level.......................................................................................................................................................85 dB(A)
The declared noise emission level of the appliance is 85 dB(A), which represents alevel Aof acoustic
power with respect to areference acoustic power of 1 pW.

04/2021
- 10 -
Copyright © 2021, Fast ČR, a.s.
INSTRUCTIONS AND INFORMATION REGARDING THE
DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at asite designated for waste in your municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on products or original documents means that used electric or
electronic products must not be added to ordinary municipal waste. For
proper disposal, renewal and recycling hand over these appliances to
determined collection points. Alternatively, in some European Union states or
other European countries you may return your appliances to the local retailer
when buying an equivalent new appliance.
Correct disposal of this product helps save valuable natural resources and
prevents potential negative eects on the environment and human health,
which could result from improper waste disposal. Ask your local authorities or
collection facility for more details.
In accordance with national regulations penalties may be imposed for the incorrect disposal
of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic appliances, ask your retailer or supplier for the
necessary information.
Disposal in other countries outside the European Union
This symbol is valid in the European Union. If you wish to dispose of this product, request the
necessary information about the correct disposal method from the local council or from your
retailer.
This product meets all the basic requirements of EU directives related to it.