Setra Systems 526 User manual

Installation Guide
MODELS 522 / 526
Pressure Transducers
560550-0087
Rev A
1-800-257-3872 TOLL FREE
1-978-264-0292 FAX
www.Setra.com Web Site

Setra offers a complete line of
products for these industries:
Industrial
HVAC
Test & Measurement
Barometric
Ultra High Purity / Sanitary

Please Note:Series 522 / 526 are designed and manufactured in accordance with sound engineering
practice as defined by the Pressure Equipment Directive 97/23/EC. This product must not be used as a
“safety accessory” as defined by the Pressure Equipment Directive, Article 1, Paragraph 2.1.3. The CE
Mark on the unit does not relate to the Pressure Equipment Directive.
INTRODUCTION
The Series 522 / 526 pressure transducers use molecularly bonded high output strain gauges to provide
100mV output for full range pressure, when used with a 10V d.c. power supply.
Series 522 / 526 high output pressure transducers and transmitters are fitted with an ASIC providing
various optional (at time of order) voltage outputs, and a 4-20mA current output capable of being used
in control and indicating loops without further amplification.
Series 522 / 526 with the CE Mark conform with the essential protection requirements of the EMC
Directive 89/33/EEC amended by certified type testing to EN 50082-2 and EN 50081-1.
HAZARDOUS PRODUCTS
The Consumer Protection Act of 1987, Section 6 of the Heath and Safety at Work Act 1974 and the
Control of Substances Hazardous to Health Regulations 1988 require that we advise recipients and
users of our products of any potential hazards associated with their storage, handling or use.
The products which our Company supplies may be classified as Electrical, Electro-Mechanical and
Electronic equipment.
These products are tested and supplied in accordance with our published specifications or individual
special requirements that are agreed in writing at time of order. They are constructed so as not to affect
adversely the safety of persons and property when properly installed, maintained and used by qualified
personnel, in the applications for which they were designed and manufactured.
Conformity with the requirements of the CE mark only applies when the installation
conditions described in these instructions have been met. For units supplied without
a cable assembly connection to the transducer must be accomplished using Setra
Systems approved cable. See APPROVED CABLE section.
GENERAL
*Transducer should not be subjected to greater than the maximum allowable pressure
listed on label and the following operating temperature specifications:
Compensated Temperature Range: -5°F to +180°F (-20°C to +80°C)
Operable Temperature Range:
Electrical Connection Code E1 -40° to +260°F (-40°C to +125°C)
Electrical Connection Code N1 -5°F to +180°F (-20°C to +80°C)
Electrical Connection Code NA -5°F to +125°F (-20°C to +50°C)
*Transducer should not be subjected to mechanical impact.
*In the event of fire the end user must ensure that the system pressure is vented to a safe
area.

*The effects of decomposition of unstable fluids should be considered by the user when
placing this device in service.
*The pressure transducer has no means of draining or venting, this must be performed by
another component in the end users system.
*Pressure range must be compatible with the maximum pressure being measured.
*Pressure media must be compatible with the transducer/transmitter wetted parts listed in
these instructions.
*Liquid must not be allowed to freeze in the pressure port.
*The gasket must be fitted under the electrical connector.
MECHANICAL INSTALLATION
Mounting: Pressure Transducer is designed to be attached by the coupling thread only. Omni-
directional, self supported directly into the pipework. Use a 19mm AF (3/4") wrench on the hexagon
provided to apply a maximum torque of 11.6 lb.ft (15.8Nm). The Customer must ensure that the
pressure seal is suitable for the application. If in doubt contact Setra Systems.
ELECTRICAL INSTALLATION
All types with the CE Mark include suppression devices providing transient protection to EN 61000-4-2
and EN 61000-4-4. Conformity with the requirements of the CE mark only applies when connection is
made with Setra Systems approved cable, see APPROVED CABLE section, and is connected as
shown below:-
Millivolt Output Transducers: Four wire shielded cable should be used with the cable shield
connected to the instrumentation ground. The cable shield should not be connected to the transducer
body.
High Output Transducers: The shield of the cable must be grounded at the instrumentation end. If
a ‘ground loop’ problem is encountered when the body of the unit is grounded by the piping it is
permissible to remove the cable shield from the instrumentation ground.
APPROVED CABLE
Setra Systems uses cables comprising 2, 3 or 4 color-coded wires, enclosed by an aluminised polyester
shield where the shield is in contact with a separate drain wire. The outer shield is chrome PVC and
overall diameter is approximately 0.20in.
OPERATION
Having installed the transducer as instructed, it is ready for use. The transducer should not be removed
while the system is at pressure. Before applying power, check that the correct polarity and excitation
levels are being applied. See Table 1 for electrical connections.
CALIBRATION
Transducers are calibrated at time of order:
Code A Absolute datum
Code G Gauge datum vented to atmosphere via the electrical connector or cable
Code C Compound datum

LOAD CHARACTERISTICS (4-20mA Current Output)
The total resistive load in the loop (to include all the cable resistance) can be from 'zero to 50 x (supply
volts -7) ohms' e.g. with a 24V d.c. supply the permissible load is from zero up to 850 ohms.
OPERATIONAL LIFE
Limited to 100M cycles to maximum allowable pressure.
WARRANTY
We guarantee this instrument against faulty workmanship and material for a period of two years from
date of delivery. The Company undertake to repair, free of charge, ex-works any instrument found to
be defective within the specified period providing the instrument has been used within the specification in
accordance with these instructions and has not been misused in any way.
Detailed notice of such defects and satisfactory proof thereof must be given to the Company immediately
after the discovery and the goods are to be returned free of charge to the Company, carefully packed
and accompanied by a detailed failure report. See "RETURN TO FACTORY".
WETTED PARTS
316 and 17-4 PH stainless steel plus Nickel Braze to BS1845 : NK3/HTN2.
SERVICING
The transducer cannot be repaired locally and if damaged should be returned to Setra Systems with the
following:-
1. Name and phone number of person to contact
2. Shipping and billing information
3. Full description of malfunction
4. Remove any pressure fittings and plumbing that you may have installed and enclose any required
mating electrical connectors and wiring diagrams.
Please ship prepaid to Setra Systems at the address shown below to to your local Setra Distributor
when a replacement/repair is required:
United States Outside The United States
Setra Systems Inc contact your local Setra Distributor
159 Swanson Road
Boxborough, MA 01719
Attn: Repair Department
RETURN TO FACTORY
PLEASE NOTE: To comply with Health and Safety requirements, the instrument must be clean and
safe to handle and accompanied by a formal statement to that effect duly signed by an authorised officer
of the Company.

Any instrument returned without certification will be quarantined and no action will occur until cleared. It
may ultimately be returned to you and subject to a transportation charge.
MAINTENANCE
Routine Inspection: Not required except for periodic inspection of the cable and connector to
ensure that these are neither damaged nor softened by incompatible liquid.

TABLE 1
CONNECTIONS 522 / 526 SERIES
TYPE
NUMBER CE CONNECTOR mV 4-20mA VOLTAGE
IN+ OUT+ OUT- IN- EARTH IN+ IN- EARTH IN+ COM OUT+ EARTH
522BP-E1 YES MINI DIN STYLE 12 3E
522BP-NA YES CABLE WEATHER PROOF RYBL G
S22BP-N1 YES CABLE USA RWGBK
522BP-E1 YES MINI DIN STYLE 1 2 E1 2 3 E
522XX-NA YES CABLE WEATHER PROOF RBK DRAIN RBK WDRAIN
522XX-N1 YES CABLE USA RBK DRAIN RBK WDRAIN
526BP-B1 YES 8-4P AB C D
526BP-C2 YES 10-6P AB C D
526BP-E2 YES LARGE DIN 12 3E
526BP-UA YES MOLDED IMMERSIBLE RYBWDRAIN
526BP-UA YES MOLDED IMMERSIBLE RYBWDRAIN
526BP-A2 YES CONDUIT LEADS RWGBK
526XX-B1 YES 8-4P ABD A C B D
526XX-B3 YES 10-6P ABEAC B E
526XX-C2 YES LARGE DIN 1 2 E1 2 3 E
526XX-UA YES MOLDED IMMERSIBLE RBL DRAIN RWYDRAIN
526XX-UA YES MOLDED IMMERSIBLE RBL DRAIN RWYDRAIN
526XX-A1 YES CONDUIT LEADS RBK GRBK WG
OUTPUT SUPPLY VOLTAGE OUTPUT SUPPLY VOLTAGE
BP 0 to100mV 10V d.c. 27 1 to 5V 6.5 to 35V d.c.
11 4 to20mA 7 to 35V d.c 24 0.5 to 5.5V 7 to 35V d.c.
28 1 to 6V 7.5 to 35V d.c 2B 0 to 5V 6.5 to 35V d.c.
2R 1 to 11V 12.5 to 35V d.c 2C 0 to 10V 11.5 to 35V d.c.
159 Swanson Road, Boxborough, MA 01719-1304
Tel: [phone]
OP522/526 Rev A 11/03