SGS SHHP50 User manual

FOR YOUR SAFETY
PLEASE READ THESE INSTRUCTIONS CAREFULLY
AND RETAIN THEM FOR FUTURE USE.
OWNER’S MANUAL
SHHP50 FLOOR STANDING
HYDRAULIC PRESS

SAFETY INSTRUCTIONS
Please read these instructions carefully. Note the safety
Instructions and warnings. Use the product correctly and with care for the pur-
pose of which it is intended. Failure to do so may cause damage to property
and/or serious personal
Injury. Please keep this instruction manual safe for future use.
We’ve done all we can to ensure this press offers the utmost in safety but
you have to do your part. No amount of warning can take the place of good
judgement, so make sure it’s the first thing you bring to any job. Beyond that
here are some tips:
Steel and other materials can shatter. Always use protective eye-wear, a full-
face impact safety shield and heavy duty work gloves that comply with the
appropriate ansi code.
If you detect anything that may indicate imminent structural failure stop using
the press immediately and inspect it
Thoroughly.
Bolt the press to the floor if it is to be used on bulky or
Unstable items.
Do not use the press to compress springs or any other item that could disen-
gage and cause a potential
Hazard.
Use a qualified person to maintain the press in good
Condition. Keep it clean for safe and optimum performance.
Do not exceed the rated capacity. Never apply excessive force to a work
piece and always use the pressure gauge to accurately determine the ap-
plied load.
SPECIFICATION
MAX CAPACITY 50 TON
STROKE 200MM
WORK RANGE 68-920MM
WEIGHT 293kg
WWW.SGS-ENGINEERING.COM PAGE 2

SAFETY INSTRUCTIONS
Use this press for the purpose for which it is intended. Do not use it for any
purpose it is not designed to perform.
Keep children and unauthorised persons away from the work area.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jew-
ellery and contain long hair. Keep proper balance and footing, do not over
reach, wear non-skid footwear.
Only use this press on a surface that is stable, level, dry, not slippery and
capable of sustaining the load. Keep the surface clean, tidy and free from
unrelated materials and ensure that there is adequate lighting.
Inspect the press before each use. Do not use if bent, broken, cracked, leak-
ing or otherwise damaged or if it has been subjected to a shock load.
Check to ensure that all applicable bolts and nuts are firmly tightened.
Ensure the work piece is centre-loaded and secure.
Keep hands and feet away from the bed area at all times.
Do not operate the press when you are tired or under the influence of alco-
hol, drugs or any intoxicating medication.
Do not allow untrained persons to operate the press.
Do not make any modifications to the press.
Do not use brake fluid or any other improper fluid and avoid mixing different
types of oil when adding hydraulic oil to the press. Only high quality hydrau-
lic oil should be used.
BEFORE FIRST USE
Before first use of this press purge any air from the hydraulic system.
Check all parts and conditions – if there is any broken part stop using the press and
contact SGS Engineering immediately.
Attach your air line to the pump if required.
PAGE 3

MAINTENANCE
Clean the outside of the press with a dry, clean and soft cloth and periodically lubri-
cate the joints and all moving parts with a light oil.
When not in use store the press in a dry location with the ram and piston fully re-
tracted.
Check the hydraulic oil; remove the oil filler nut on the top of the reservoir and if the
oil level is not adequate fill with high quality hydraulic oil as necessary. Then replace
the oil filler nut and purge air from the system.
OPERATING INSTRUCTIONS
Raise the work bed using the winch to the required height and move the pins to suit.
Close the release valve by turning it clockwise until it is firmly closed.
Use the foot pedal (air) or pump the handle until the saddle nears the work piece.
Align the work piece and ram to ensure centre-loading.
Pump the handle to apply load onto the work piece.
When work is complete, stop pumping the handle, slowly and carefully remove the
load from the work piece by turning the release valve anti-clockwise in small incre-
ments. Once the ram has fully retracted remove the work piece from the bed frame.
SYSTEM AIR PURGE
1. Open the release valve by turning it anti-clockwise.
2. Pump several full strokes to eliminate any air from the system.
3. Close the release valve
WWW.SGS-ENGINEERING.COM PAGE 4

PAGE 5

WWW.SGS-ENGINEERING.COM PAGE 6

PAGE 7

FOR YOUR SAFETY
PLEASE READ THESE INSTRUCTIONS CAREFULLY
AND RETAIN THEM FOR FUTURE USE.

EC Declaration of Conformity
This is an important document and should be retained
MANUFACTURER’S NAME:
TYPE OF EQUIPMENT:
PART NUMBER:
I, the undersigned, hereby declare that the equipment specied above
conforms to the above European Communities Directive(s) and
Standard(s).
PLACE:
DATE: (Signature)
Robert Wyatt
Company Secretary
Derby, UK
24th JUNE 2017
SGS Engineering (UK) Ltd
SGS Engineering (UK) Ltd
West Side Park
Raynesway
Derby, DE21 7AZ
Hydraulic Press
SHHP50
2006/42/EC Machinery Directive
EN ISO 12100-1:2003 +A1:2009
EN ISO 12100-2:2003 + A1:2009
APPLICATION OF EC COUNCIL DIRECTIVES / STANDARD: