Shade N' Shelters UMB-10-STD User manual

1of9
Owner’s Manual
10' Offset Umbrella with Base
Model Number: UMB-10-STD
SKU Number: 101644194
Additional Product Information: https://shadenshelters.com/10-round-offset-umbrella

2of9
Parts List
10' Offset Umbrella with Base
Letter
Illustration
Description
Qty.
Letter
Illustration
Description
Qty.
A
Base Plate
1
H
Poly Base -
Middle
2
B
Base Plate
1
I
Main Support
Post with
Umbrella
Canopy
1
C
Swivel Plate
1
J
M8 x 15mm Bolt
4
D
Lower Umbrella
Support Post
1
K
M8 x 20mm Bolt
4
E
Swivel Plate
Cover-Bottom
1
L
Steel Washer
8
F
Swivel Plate
Cover-Top
1
M
Open Wrench
1
G
Poly Base - Side
2

3of9
Assembly Instructions
10' Offset Umbrella with Base
Important:
⚫Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
⚫Before beginning to assemble the product, remove all protective materials, hardware kit(s), and
identify all parts packed in the carton are present. (Note: If any part is missing or damaged, do not
attempt to assemble). Contact Shade N’ Shelters Customer Support Team. See page 9.
⚫Two people are required to assemble heavy items.
⚫Assemble product on a soft and non-abrasive surface, such as carpet to avoid damaging the item.
SAFTEY WARNINGS
➢Completely Fill Poly Base with sand or water prior to assembly and use.
➢Close and secure the umbrella when not in use or during inclement weather.
➢Never use umbrella in high wind conditions or near flame/heat sources.
ASSEMBLY INSTRUCTIONS
Step 1: Place Base Plate (A) across the top of Base Plate (B). Secure the Swivel Plate (C) using Bolts (K)
and Washers (L). Attach the Lower Umbrella Support Post (D) to the Swivel Plate (C) using Bolts
(J) and Washers (L). Tighten all Bolts. See Figure 1.
Figure 1

4of9
Step 2: Remove caps from the side of all Poly Bases (G & H) and fill completely with Sand or Water.
Secure the caps on all bases. See Figure 2.
Note: Poly Bases must be completely filled with sand or water before proceeding to the next step.
Figure 2
Step 3: Place the Filled Poly Bases (G & H) on the Base Plates (A & B). See Figure 3-1 and Figure 3-2.
Figure 3-1 Figure 3-2

5of9
Step 4: Remove the Locking Nuts from the Lower Umbrella Support Post (D) and attach the Bottom Swivel
Plate Cover (E) and Top Swivel Plate Cover (F). See Figure 4.
Note: The Locking Nut is reattached in Step 5.
Figure 4
Step 5: Insert the Main Support Post with Umbrella Canopy (I) into the Lower Umbrella Support Post (D).
Insert and Tighten Locking Nuts to secure the Lower Umbrella Support (D) to the Main Support
Post with Umbrella Canopy (I). See Figure 5.
Figure 5
Locking Nuts

6of9
OPERATING INSTRUCTIONS
Step 6: RAISING UMBRELLA CANOPY.
Untie the Tie Strap and loosen the Umbrella Fabric before raising. See Figure 6.
Note: The Umbrella Canopy must be in the closed position prior to raising or lowering the height.
Figure 6
Step 7: Slowly lift the curved bar upwards to extend the canopy to the highest position. Lock the arm by
moving the sleeve downward. Lock the canopy height by lowering the handle on the vertical post
to the lock position. See Figure 7.
Figure 7

7of9
Step 8: OPENING UMBRELLA CANOPY.
Once the Umbrella Canopy is at the desired height, open the Canopy by turning the Umbrella Crank
in the clockwise position. To close the Umbrella Canopy, turn the Umbrella Crank in the counter
clockwise position. See Figure 8.
Figure 8
Step 9: ROTATING UMBRELLA CANOPY.
Depress and hold the pedal on the Swivel Plate (C) with your foot while turning the Main Support
Post (I) to the desired locking position. The Main Support Post (I) can rotate 360 degrees. See
Figure 9.
Figure 9

8of9
Step 10: LOWERING UMBRELLA CANOPY.
Close the Umbrella Canopy by turning the Umbrella Crank counter-clockwise. See Figure 10-1.
Release the Arm Lock by moving the Sleeve in the upward direction. Release the Height Lock by
raising the lever to the unlock position. Slowly lower the curved bar to the lowest position. See
Figure 10-2. Secure the Umbrella Canopy to the pole with the Tie Strap. See Figure 10-3.
Figure 10-1
Figure 10-2 Figure 10-3

9of9
Care & Maintenance
Maintain your umbrella by storing out of the elements when not in use.
Frame: Clean frames with a mild soap and warm water. Do not use abrasive materials, cleaners or bleach.
Rinse with clean water and dry thoroughly. Always clean, drain and dry thoroughly before storing
for the winter.
Fabric: Clean by hand with a mild solution of soap and water. Rinse fabric thoroughly and allow to drip
dry. Do not use bleach or solvents on fabrics.
Warranty
You must retain the original receipt to obtain warranty service.
What is covered?
Frame: Frame is warranted against rusting for 1-year.
Finish: Frame is warranted against peeling, cracking or blistering for 1-year if the product has not been
scratched or abraded.
Fabric: Fabric is covered by a 1-year warranty against manufacturing defects.
What is not covered?
EXCLUSIONS: Use for commercial, contract, or other non-residential purposes, or items damaged due to acts of
nature, vandalism, misuse, or improper assembly are not covered. Discoloration or fading of the finish or fabrics
as a result of chemicals or spills, pool water chemicals or salt water is not covered. Mildew of fabric is not covered.
Corrosion and rusting of frames resulting from scratches are not covered. If within the stated warranty period this
product is found to be defective in material or workmanship, the purchaser must contact the manufacturer’s
customer service department. The manufacturer, at its option, will repair or replace the defective parts. Proof of
purchase (dated register receipt) is required for warranty claims. It remains the customer’s responsibility to pay
for freight and packing charges to and from the service center. Warranty is to the original purchaser and is non-
transferable. Any replacement of warranted items will be in the original style and color, or similar style and color
if the original is unavailable or has been discontinued.
Questions, problems, missing or damaged part? Before returning to the store call or email our Customer Service.
Customer Service Contact Information:
Hours: Monday - Friday 8:00 a.m. - 5:00 p.m. Central Time (CT)
Phone: [phone]
Email: [e-mail]