Shade N' Shelters Belmont BEL/GAZ-2 User manual

1of11
Owner’s Manual
Belmont
8’ x 5’ Grill Gazebo
Model Number: BEL/GAZ-2
SKU Number: 101641930
Note: This gazebo frame is designed to be used as a permanent fixture. The Grill Gazebo cover is
recommended when not in use or storing for winter. Please visit: https://shadenshelters.com to
purchase.
Scan For Video
Assembly Instructions!

2of11
Parts List
Belmont 8’ x 5’ Grill Gazebo
Letter
Illustration
Description
Qty.
A1
Corner Post
2
A2
Corner Post
2
B
Roof Beam-Long Side
2
C
Roof Beam-Short Side
2
D
Corner Supports
8
E1
Roof Frame-Long Side
2
E2
Roof Frame-Long Side
2
F
Roof Frame-Short Side
2
G
Roof Beam-Top
1
H
Roof Frame-Middle
2
I
Roof Support
4

3of11
Letter
Illustration
Description
Qty.
J
Roof Support
2
K
Roof Frame Connector Plate
2
L
Roof Corner Connector Plate
4
M
Bar Shelf
2
N
Bar Shelf Connector Plate
4
O
Bar Shelf Connector Plate
4
P
Roof Panel Connector Plate
12
Q1
Roof Panel
2
Q2
Roof Panel
2
Q3
Roof Panel
2
R
Roof Trim-Top
1
S
Base Cover
4

4of11
Letter
Illustration
Description
Qty.
T
Base Plate
4
U
Roof Frame-Horizontal
4
AA
M6 x 15mm Bolt with Washer
128
BB
M6 x 40mm Bolt with Washer
2
CC
Screw with Washer
8
DD
Ground Stake
8
EE
M6 Hex Wrench
2
FF
Allen Wrench
1

5of11
Assembly Instructions
Belmont 8’ x 5’ Grill Gazebo
Note: For video instructions please visit:
https://shadenshelters.com/8-x-5-grill-gazebo
Important:
⚫Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
⚫Before assembling the product, remove all protective materials, hardware kit(s), and identify all
parts packed in the carton are present. (Note: If any part is missing or damaged, do not attempt to
assemble). Contact Shade N’ Shelters Customer Support. See page 11.
⚫Assemble on a stable level surface to avoid damage to gazebo and possible injury.
⚫Two people are required to assemble this product.
⚫Gazebo dimensions are measured from roof corner to roof corner.
WARNING: DO NOT TIGHTEN BOLTS UNTIL NOTED AFTER EACH STEP!
Step 1: Insert the Corner Post (A1/A2) into the Base Cover (S),then connect the Base Plate (T) to the
Corner Post (A1/A2) with Bolt (AA). Repeat for opposite side. Tighten all Bolts. See Figure 1.
Figure 1

6of11
Step 2: Attach the Long and Short Roof Beams (B/C) to the Corner Posts (A1/A2) with Bolt (AA). Repeat
for opposite side. Tighten Bolts. See Figure 2-1, Figure 2-2 and Figure 2-3.
Figure 2-2 Figure 2-3
Figure 2-1

7of11
Step 3A: Attach the Corner Supports (D) to the Roof Beam (B/C) and the Corner Posts (A1/A2) with Bolts
(AA). Repeat for all corners. See Figure 3-1.
Step 3B: Attach the Long Roof Frames (E1/E2) to the Corner Posts (A1/A2) with Bolts (AA). Repeat for
opposite side. See Figure 3-2.
Step 3C: Attach Roof Supports (J and I) to the Long Roof Beams (B) with Bolts (AA). Attach opposite end
of Roof Supports (I) to Long Roof Frames (E1/E2) using bolts (AA). See Figure 3-3A and Figure 3-
3B.
Step 3D: Attach Top Roof Beam (G) to Long Roof Frames (E1/E2) and Roof Support (J) using bolts (AA).
See Figure 3-4.
Step 3E:Repeat for opposite side. Tighten all Bolts. See Figure 3-5.
Figure 3-3A Figure 3-3B Figure 3-4
Figure 3-1
Figure 3-2
Figure 3-5

8of11
Step 4A: Attach the Middle Roof Frame (H) to the Roof Top Beam (G) and the Roof Beam (C) with Bolts
(AA). Repeat for opposite side. See Figure 4-1A and Figure 4-1B.
Step 4B: Attach the Roof Frame Connector
Plate (K) to the Middle Roof
Frame (H) with Bolts (AA).
Repeat for opposite side. See
Figure 4-2.
Step 4C: Attach the Horizontal Roof Frame
(U) to the Long Roof Frames
(E1/E2) and the Roof Frame
Connector Plate (K) with Bolts
(AA). Repeat for opposite side.
See Figure 4-3A and Figure 4-3B.
Step 4D: Attach the Roof Corner Connector
Plate (L) to the Long Roof Frames
(E1/E2) and the Roof Frame-
Short Side (F) with Bolts (AA).
Repeat for all Corners. See Figure
4-4.
Step 4E: Tighten All Bolts. See Figure 4-5.
Figure 4-1A Figure 4-1B Figure 4-2
Figure 4-3A Figure 4-3B Figure 4-4
Figure 4-5

9of11
Step 5A: Install the Roof Panels (Q1, Q2 and Q3) from left to right. The right panel must overlap the left
panel. See Figure 5-1.
Step 5B: Secure the Roof Panels (Q1, Q2 and Q3) with the Roof Panel Connector Plates (P) to the Roof
Frame-Short Side (F) with Bolts (AA). Repeat for opposite side. See Figure 5-2.
Step 5C: Install the Roof Top Trim (R) to the Roof Top Beam (G) with Bolts (BB). See Figure 5-3.
Step 5D: Secure the Roof Panels (Q1 and Q3) to the Roof Frames (E1/E2) with Screws (CC). Repeat for
opposite side. See Figure 5-4.
Step 5E: Tighten all bolts.
Figure 5-1
Figure 5-2
Figure 5-3
Figure 5-4
CC

10 of11
Step 6A: Attach the Bar Shelf Connector Plate (N) to the Corner Post
(A1/A2) with Bolts (AA). Repeat for opposite side. See Figure 6-1.
Step 6B: Attach the Bar Shelf (M) to the Bar Shelf Connector Plate (N) with
Bolts (AA). Repeat for opposite side. See Figure 6-2.
Step 6C: Attach the Bar Shelf Connector Plate (O) to the Corner Post
(A1/A2) and the Bar Shelf (M) with Bolts (AA). Repeat for opposite
side. See Figure 6-3A and Figure 6-3B.
Step 6D: Tighten all Bolts.
Step 6E: Secure the gazebo with the Ground Stakes (DD). See Figure 6-4.
Figure 6-4 Figure 6-3B
Note: Please see our video for additional assembly assistance:
https://shadenshelters.com/8-x-5-grill-gazebo
Figure 6-3A
Figure 6-2
Figure 6-1

11 of11
Care & Maintenance
Maintain your outdoor grill gazebo by using a Grill Gazebo Cover when not in use or storing for winter.
Please visit: https://shadenshelters.com to purchase.
Frame: Do not allow debri or snow to accumulate on roof it may create hazardous conditions. Clean the
frame with a mild soap and warm water. Do not use abrasive materials, cleaners or bleach. Rinse
with clean water and dry thoroughly.
Warranty
You must retain the original receipt to obtain warranty service.
What is covered?
Frame: Frame is warranted against rusting for 1-year
Finish: Frame finish is warranted against peeling, cracking or blistering for 1-year if the product has not
been scratched or abraded.
What is not covered?
EXCLUSIONS: Gazebo use for commercial, contract, or other non-residential purposes, damage due to acts
of nature, vandalism, misuse, or improper assembly are not covered. Discoloration or fading of the finish or
fabrics as a result of chemicals or spills, pool water chemicals or salt water is not covered. Mildew of fabric is
not covered. Corrosion and rusting of frames and hardware is not covered. If within the stated warranty
period this product is found to be defective in material or workmanship, the purchaser must contact the
manufacturer's customer service department. The manufacturer, at its option, will repair or replace the
defective parts. Proof of purchase (dated register receipt) is required for warranty claims. It remains the
customer's responsibility to pay for freight and packaging charges to and from the service center. Warranty
is to the original purchaser and is non-transferable. Any replacement or warranted items will be in the
original style and color, or similar style and color if the original is unavailable or has been discontinued.
Questions, problems, missing or damaged part? Before returning to the store call or email our Customer
Service.
Customer Service Contact Information:
Hours: Monday - Friday 8:00 a.m. - 5:00 p.m. Central Time (CT)
Phone: [phone]
Email: [e-mail]