Shade N' Shelters Lexington LEX/GAZ-2 User manual

1of9
Owner’s Manual
Lexington
9’ x 11’ Soft Top Gazebo
Model Number: LEX/GAZ-2
SKU Number: 101641932
Note: This gazebo frame is designed to be used as a permanent fixture. Remove canopy when not
in use or during high winds, rain or snow.
Scan For Video
Assembly Instructions!

2of9
Parts List
Lexington 9’ x 11’ Soft Top Gazebo
Letter
Illustration
Description
Qty.
A
Center Roof Connector
1
B
Corner Roof Support-Long (86 1/2")
4
C
Side Roof Support-Short (57")
2
D
Side Roof Support-Medium (68")
2
E1
Short Cross-Beam (55 3/4")-Left
2
E2
Short Cross-Beam (55 3/4")-Right
2
F
Long Cross-Beam (90 1/2")
2
G
Base Plate
4
H
Top Connector Plate with "U" Bracket (for
Short Cross-Beams)
2
I
M6 x 78mm Bolt with Washer, Nut Plastic
Nut Cap
4
J
Bottom Connector Plate (for Short Cross-
Beams)
2
K
Vertical Corner Post
4

3of9
Letter
Illustration
Description
Qty.
L
Small "U" Bracket for Vertical Corner Post
and Long Cross-Beam
6
M
Ground Stakes
8
N
M6 x 30mm Bolt with Washer, Nut Plastic
Nut Cap
24
O
M6 x 15mm Bolt and Washer
22
P
M6 x 15mm Screw
6
Q
Roof Vent Canopy
1
R
Main Canopy
1
S
Mosquito Netting
4
T
Ring Connectors
52
U1
Wrench
2
U2
Allen Wrench
1

4of9
Assembly Instructions
Lexington 9’ x 11’ Soft Top Gazebo
Note: For video instructions please visit:
https://shadenshelters.com/9-x-11-lexington-gazebo
Important:
⚫Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
⚫Before assembling the product, remove all protective materials, hardware kit(s), and identify all
parts packed in the carton are present. (Note: If any part is missing or damaged, do not attempt to
assemble). Contact Shade N’ Shelters Customer Support. See page 9.
⚫Assemble on a stable level surface to avoid damage to gazebo and possible injury.
⚫Two people are required to assemble this product.
⚫Gazebo dimensions are measured from roof corner to roof corner.
WARNING: DO NOT TIGHTEN BOLTS UNTIL NOTED AFTER EACH STEP!

5of9
I. Cross-Beam Assembly:
Step 1: Attach the Short Cross Beam (E1) to the Short Cross Beam (E2) using the Top Connector Plate (H)
and Bottom Connector Plate (J) using Bolt, Washer and Nut (N). See Figure 1.
Note: The round steel rail on the Cross-Beam is the top side.
Step 2: Repeat for remaining Short Cross Beams (E1/E2).
Step 3: Attach Small “U” Bracket (L) to both Long Cross-Beams (F) using Screw (P). See Figure 2.
II. Side Frame Assembly:
Step 1: Attach Small “U” Brackets (L) to top of each Corner Post (K) using Screw (P). See Figure 3.
Note: Screws should only be finger-tight at this point to allow the “U” Bracket (L) to move so you can
adjust the angle in Section III; Step 1.

6of9
Step 2: Attach the Base Plates (G) to the Corner Post (K) using Bolt, Washer and Nut (I). See Figure 4.
Step 3: Attach the 2 Assembled Short Cross-Beams (E1, E2) and Long Cross-Beams (F) to the Corner Posts
(K) with Bolt & Washer (O). See Figure 5.
Note: This step requires help from a third person.
Note: The round steel rail welded on the Cross-Beam must face the inside of the gazebo.
Note: The Assembled Short Cross-Beams are on opposite sides of the gazebo and the Long Cross-
Beams are also opposite each other.
III. Roof Frame Assembly:
Step 1: Insert the “Push Button” end of the Long Corner Roof Support (B) to the Center Roof Connector (A)
until “Push Button” locks. See Figure 6. Align the opposite end of the Corner Roof Support (B) with
the Small “U” Bracket (L) on the Corner Posts (K).
Secure the Small “U” Bracket (L) by tightening Screw (P) then attach the Long Corner Roof Support
(B) with Bolt and Nut (N). See Figure 7.

7of9
Step 2: Insert the “Push Button” end of the “Short” Roof Support (C) into the Center Roof Connector (A) and
attach to the “U” Bracket (L) on top of the Assembled Cross-Beams (E1 & E2) using Bolt, Washer, and
Nut (N). See Figure 8.
Note: Roof Assembly requires a Step Ladder and help from a third person.
Step 3: Insert the “Push Button” end of the “Medium” Roof Support (D) into the Center Roof Connector (A)
and attach to Long Cross-Beams (F) using Bolt, Washer, and Nut (N). See Figure 9.
IV. Canopy/Valance Assembly:
Step 1: Place the Main Canopy (R) over the Roof. Leave the Main Canopy loose until Roof Vent Canopy has
been installed. Note: Roof Vent Frame must remain exposed. Roof Vent Frame is welded to the top
of Roof Supports (B).
Step 2: Place Roof Vent Canopy (Q) over Roof Vent Frame and secure to the ends of the Roof Vent Frame.
See Figure 11.
Step 3: Firmly secure the Main Canopy (R) to the ends of the Main Roof Support Frame (B, C, and D). See
Figure 10.
Step 4: Insert the Valance between the Round Steel Rail and the Cross-beam.

8of9
V. Mosquito Netting Assembly:
Step 1: Before attaching the Mosquito Netting (S), align all four sections on the ground next to the gazebo.
Make sure the zippers are aligned in the center of each opening. The Fabric Tie-Backs sewn to the
Mosquito Netting (S) also must be aligned with each Corner Post (K).
Step 2: Insert the Plastic Ring Connectors (T) thru the Elastic Bands on the Mosquito Netting and attach to
the Round Steel Rail on the inside of the Cross-Beams. Snap the ring firmly together to lock. Repeat
for each section of Mosquito Netting (S). See Figure 12.
Step 3: To open the Mosquito Netting (S), unzip at the center and attach to the Corner Posts (K) using the
Fabric Tie-Backs.
VI. Securing the Gazebo:
Step 1: Insert the Ground Stakes (M) into the holes of the Base Plate (G). See Figure 13.
Note: Gazebo Dimensions 9' x 11' are measured from roof canopy.
Note: Please see our video for additional assembly assistance:
https://shadenshelters.com/9-x-11-lexington-gazebo

9of9
Lexington Gazebo Accessories
Please visit https://shadenshelters.com to purchase
➢Privacy Curtain
➢Replacement Roof Canopy
➢Replacement Mosquito Netting
Care & Maintenance
Maintain your gazebo by removing the canopies and storing out of the elements when not in use, or during
hazardous weather conditions (wind, rain, snow, etc.).
Frame: Clean frames with a mild soap and warm water. Do not use abrasive materials, cleaners or bleach.
Rinse with clean water and dry thoroughly.
Fabric: Canopy may be cleaned by hand with a mild solution of soap and water. Rinse thoroughly and allow
to drip dry. Do not use bleach or solvents on fabrics.
Warranty
You must retain the original receipt to obtain warranty service.
What is covered?
Frame: Frame is warranted against rusting for 1-year
Finish: Frame Finish is warranted against peeling, cracking or blistering for 1-year if the product has not
been scratched or abrade.
Fabric: Canopy are covered by a 1-year warranty against manufacturing defects.
What is not covered?
EXCLUSIONS: Gazebo use for commercial, contract, or other non-residential purposes, damage due to acts
of nature, vandalism, misuse, or improper assembly are not covered. Discoloration or fading of the finish or
fabrics as a result of chemicals or spills, pool water chemicals or salt water is not covered. Mildew of fabric is
not covered. Corrosion and rusting of frames and hardware is not covered. If within the stated warranty
period this product is found to be defective in material or workmanship, the purchaser must contact the
manufacturer's customer service department. The manufacturer, at its option, will repair or replace the
defective parts. Proof of purchase (dated register receipt) is required for warranty claims. It remains the
customer's responsibility to pay for freight and packaging charges to and from the service center. Warranty
is to the original purchaser and is non-transferable. Any replacement or warranted items will be in the
original style and color, or similar style and color if the original is unavailable or has been discontinued.
Questions, problems, missing or damaged part? Before returning to the store call or email our Customer
Service.
Customer Service Contact Information:
Hours: Monday - Friday 8:00 a.m. - 5:00 p.m. Central Time (CT)
Phone: [phone]
Email: [e-mail]