Shade N' Shelters Granite Peak GP/GAZ-1212 User manual

1of22
Owner’s Manual
Granite Peak
12’ x 12’ Hard Top Gazebo
Model Number: GP/GAZ-1212
Note: This gazebo is designed to be used as a permanent fixture.
Scan For Video
Assembly Instructions!

2of22
Parts List
Granite Peak 12’ x 12’ Hard Top Gazebo
Letter
Illustration
Description
Qty.
A
Corner Post
4
B
Corner Post Base Plate
4
C1
Lintel
4
C2
Lintel
4
E
Lintel Corner Support Bar
8
F
Lintel Bracket
4
G1
Lintel Connector - Small
4
G2
Lintel Connector - Large
4
H
Main Roof Corner Support
4
I
Main Roof Vertical Center Support
4
J1
Main Roof Center Frame – Short
Connector
2

3of22
Letter
Illustration
Description
Qty.
J2
Main Roof Center Frame - Long Connector
2
K1
Roof Vent - Corner Supports
4
K2
Roof Vent - Center Support
1
K3
Roof Vent Hook
1
L
Roof Vent - Top Trim
1
M
Main Roof – Lower Horizontal Support
8
N
Main Roof – Upper Horizontal Support
8
O1
Main Roof Connector – Corner
8
O2
Main Roof Connector – Center
8
P1
Roof Vent Frame
4
Q1
Main Roof Corner Trim
4
Q2
Roof Vent Corner Trim
4

4of22
Letter
Illustration
Description
Qty.
Q4
Main Roof Center Frame Trim
4
R1
Roof Vent Side Trim
4
S1
Lintel Cover - Corner
4
S2
Lintel Cover - Center
4
T1
Main Roof Panel
4
T2
Main Roof Panel
4
T3
Main Roof Panel
4
T4
Main Roof Panel
4
T5
Main Roof Panel
4
T6
Main Roof Panel
4
U1
Roof Vent Panel
4
V
Mosquito Netting
4

5of22
Letter
Illustration
Description
Qty.
AA
M6 x 15mm Bolt with Steel Washer
189
BB
M8 x 15mm Bolt with Steel Washer
48
CC
M6 x 15mm Bolt with Plastic Washer
8
DD
M6 x 15mm Bolt
16
EE
M6 x 25mm Bolt with Plastic Washer
28
FF
M6 x 35mm Bolt with Plastic Washer
8
GG
M6 x 40mm Bolt with Plastic Washer
8
II
M6 x 55mm Bolt with Flat Washer & Nut
4
JJ
Mosquito Netting Hook
48
KK
Spacer
28
LL
Ground Stake
12
MM
M8 Allen Wrench
1
NN
M6 Hex Wrench
2

6of22
Assembly Instructions
Granite Peak 12’ x 12’ Hard Top Gazebo
Note: For video instructions please visit:
https://shadenshelters.com/12x12-granite-peak-gazebo
Important:
⚫Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
⚫Before assembling the product, remove all protective materials, hardware kit(s), and identify all
parts packed in the carton are present. (Note: If any part is missing or damaged, do not attempt to
assemble). Contact Shade N’ Shelters Customer Support. See page 22.
⚫Assemble on a stable level surface to avoid damage to gazebo and possible injury.
⚫Two people are required to assemble this product.
⚫Gazebo dimensions are measured from roof corner to roof corner.
WARNING: DO NOT TIGHTEN BOLTS UNTIL NOTED AFTER EACH STEP!
Step 1: Connect Corner Post Base Plate (B) to Corner Post (A) using Bolts (AA). Repeat for all Corner Posts
and Base Plates. Tighten all Bolts. See Figure 1.
Figure 1

7of22
Step 2A: Insert Twelve Mosquito Netting Hooks (JJ) into the channel of each Lintel (C2). See Figure 2-1.
Note: The extra channel is for optional privacy curtain. Available at https://shadenshelters.com/
Step 2B: Attach Lintel Connector (G1) to Lintel (C2) using Bolts (AA). See Figure 2-2
Step 2C: Attach Lintel (C2) to Lintel Connector (G2) using Bolts (BB). Attach Lintel (C1) to Lintel Connector
(G2) using Bolts (BB).
Note: Leave 1 Bolt Hole open on both Lintels (C1 and C2) for Step 2D. See Figure 2-2.
Step 2D: Attach Lintel Bracket (F) to Lintels (C1 and C2) using Bolts (BB). Tighten all Bolts. See Figure
2-3. Repeat Step 2A to 2D for remaining Lintels (C1 and C2).
Figure 2-3
Figure 2-1
Figure 2-2

8of22
Step 3A: Attach Corner Posts (A) to end of Lintels (C1 and C2) first with Bolts (AA) then with Bolts (DD).
Tighten all Bolts. See Figure 3-1.
Step 3B: Repeat for opposite side Lintels (C1 and C2) and Corner Posts (A). See Figure 3-2.
Figure 3-1
Figure 3-2

9of22
Step 4A: Attach Corner Posts (A) to Lintel (C1 and C2) first with Bolts (AA) then with Bolts (DD). Repeat for
opposite side Lintels (C1 and C2). See Figure 4-1.
Step 4B: Attach Support Bars (E) to Lintels (C1 and C2) and Corner Post (A) with Bolts (AA).
See Figure 4-2.
Step 4C: Repeat for all Corner Posts and Lintels. Tighten all Bolts. See Figure 4-3.
Figure 4-1
Figure 4-2
Figure 4-3

10 of22
Step 5A: Attach Corner Lintel Cover (S1) to Lintel (C1) and Lintel (C2) with Bolts (AA). Repeat for all corners.
Tighten all Bolts. See Figure 5-1.
Step 5B: Attach Center Lintel Cover (S2) to Lintels (C1 and C2). Tighten all Bolts. See Figure 5-2.
Step 5C: Repeat for opposite sides. Tighten all Bolts. See Figure 5-3.
Figure 5-1 Figure 5-2
Figure 5-3

11 of22
Step 6A: Assemble the Main Roof Center Frame by inserting the Main Roof Center Frame (J2) into the Main
Roof Center Frame (J1) and attach with Bolts (AA). See Figure 6-1.
Step 6B: Repeat for opposite sides and ends. Tighten all Bolts. See Figure 6-2.
Figure 6-1
Figure 6-2

12 of22
Step 7A: Assemble the Main Roof Corner Supports (H) to the Main Roof Center Frame (J1) and then to the
Corner Posts (A) using Bolts (AA). See Figure 7-1.
Note: You will need a second person to hold the assembled Main Roof Center Frame while
attaching the Main Roof Corner Supports (H).
Step 7B: Repeat for all corners and Tighten all Bolts.
Note: Diagonal measurements from corner to corner must be within 5mm of the same distance.
See Figure 7-2.
Figure 7-1
Figure 7-2

13 of22
Step 7C: Attach the Main Roof Vertical Center Supports (I) to the Main Roof Center Frame (J1 and J2) and
on top of the Lintel Brackets (F) using Bolts (AA). Hand Tighten Only. See Figure 7-3.
Step 7D: Repeat for each side. Tighten all Bolts. See Figure 7-4
Figure 7-3
Figure 7-4

14 of22
Step 8A: Attach Roof Vent Hook (K3) to Roof Vent Center Support (K2). See Figure 8-1.
Step 8B: Assemble the Roof Vent Frame by attaching Roof Vent Corner Support (K1) to Roof Vent Center
Support (K2) with Bolts (II). Tighten all Bolts. See Figure 8-2.
Step 8C: Repeat for all corners. Tighten all Bolts. Figure 8-3.
Figure 8-1 Figure 8-2
Figure 8-3

15 of22
Step 9A: Attach the sides of the Roof Vent Frame by connecting the Roof Vent Frame (P1) to the Roof Vent
Corner Support (K1) using Bolts (AA). See Figure 9-1.
Step 9B: Repeat for opposite side. Tighten all Bolts. See Figure 9-2.
Step 9C: Secure the Roof Vent Frame to the Main Roof Center Frame by inserting the Roof Vent Corner
Supports (K1) into the Main Roof Center Frame (J1) and attach using Bolts (AA). See Figure 9-3.
Step 9D: Repeat for all corners. Tighten all Bolts. See Figure 9-4
Figure 9-1 Figure 9-2
Figure 9-3
Figure 9-4

16 of22
Step 10A: Attach the Roof Vent Panel (U1) to the Roof Vent Frame (P1) using Bolt (CC). See Figure 10-1.
Step 10B: Repeat for opposite sides. Tighten all Bolts. See Figure 10-2.
Step 10C: Attach the Roof Vent Trim (R1) to the Sides of Roof Vent Frame (P1) using Bolts (AA). Repeat for
all sides. Tighten all Bolts. See Figure 10-3.
Figure 10-1
Figure 10-3
Figure 10-2

17 of22
Step 11A: Attach the Roof Vent Corner Trim (Q2) to the Roof Vent Corner Support (K1) using Bolts (FF).
See Figure 11-1.
Step 11B: Repeat for all corners. Tighten all Bolts. See Figure 11-2.
Step 11C: Attach the Roof Vent Top Trim (L) to the Roof Vent Center Support (K2) using Bolts (BB).
Tighten all Bolts. See Figure 11-2 and Figure 11-3.
Figure 11-1 Figure 11-3
Figure 11-2

18 of22
Step 12A: Attach the Main Roof Connectors (O1) to the Main Roof Corner Supports (H) using Bolts (AA).
See Figure 12-1.
Step 12B: Attach the Main Roof Connectors (O2) to the Main Roof Vertical Center Supports (I) using Bolts
(AA). See Figure 12-2.
Step 12C: Attach the Main Roof Horizontal Supports (M and N) to the Main Roof Connectors (O1) using
Bolts (AA). See Figure 12-3.
Step 12D: Attach the Main Roof Horizontal Supports (M and N) to the Main Roof Connectors (O2) using
Bolts (AA). See Figure 12-4.
Step 12E: Repeat for all sides. Tighten all Bolts. See Figure 12-5.
Figure 12-1 Figure 12-2
Figure 12-3 Figure 12-4
Figure 12-5

19 of22
MAIN ROOF PANEL ASSEMBLY
Note: Install Main Roof Panels from Left to Right. The Right Panel must overlap the Left Panel. Each
Bolt (EE) must be attached to Spacer (KK) on top of lintels. Hand Tighten only until all panels
have been installed then tighten all bolts.
Step 13A: Attach Main Roof Left Panel (T1) to Lintel (C1 and C2) using Bolt (EE) and Spacer (KK). Hand
Tighten Only. See Figure 13-1.
Step 13B: Attach Main Roof Left Panel (T2) to Lintel (C1 and C2) using Bolt (EE) and Spacer (KK).
Note: Panel (T2) must overlap Panel (T1). Repeat installation and overlapping for Main Roof
Panels (T3, T6, T4, and T5) using Bolt (EE) and Spacer (KK). See Figure 13-2.
Step 13C: Repeat for opposite sides. Tighten all Bolts. See Figure 13-3.
Figure 13-2
Figure 13-1
Figure 13-3

20 of22
Step 14A: Attach the Main Roof Corner Trim (Q1) to the Main Roof Corner Support (H) using Bolt (GG).
Repeat for all corners. See Figure 14-1 and Figure 14-3.
Step 14B: Attach the Main Roof Center Frame Trim (Q4) to the Main Roof Center Frame (J1 and J2) using
Bolts (AA). Repeat for all sides. Tighten all Bolts. See Figure 14-2 and Figure 14-3.
Figure 14-1 Figure 14-2
Figure 14-3