Shade N' Shelters Chesterfield User manual

1 of 31
Owner’s Manual
Chesterfield
10.5’ x 10.5’ Hard Top Pavilion
Note: This pavilion frame is designed to be used as a permanent fixture. For more information,
please visit https://shadenshelters.com.

2 of 31
Parts List
Chesterfield 10.5’ x 10.5’ Pavilion
Letter
Illustration
Description
Qty.
A
Post
4
B1
Crossbar - Right Side
2
B2
Crossbar - Left Side
2
C1
Crossbar - Right Side
2
C2
Crossbar - Left Side
2
D
Roof Rafter
2
E1
Conner Support - Right
4
E2
Conner Support - Left
4
F1
Roof Rafter
2
F2
Roof Rafter
2
G
Side Rafter
4

3 of 31
Letter
Illustration
Description
Qty.
H
Roof Rafter
4
I
Roof Rafter
8
J
Roof Support Rafter
8
K
Connecting Rafter
8
L
Connecting Rafter
8
M
Supporting Rafter
2
N
L Share Bracket
4
O
L Shape Bracket
4
P1
Roof Panel
2
P2
Roof Panel
4
Q1
Roof Panel Cap
2
Q2
Roof Panel Cap
2

4 of 31
Letter
Illustration
Description
Qty.
R1
Roof Cap
1
R2
Roof Cap
1
S1
Roof Panel Profile
2
S2
Roof Panel Profile
2
T
Base Bracket
8
U
U Shape Bracket
4
V
V Shape Bracket
4
W
Ground Stake
16
AA
M10 x 180mm Bolt
16
BB
M8 x 60mm Bolt
16
CC
M8 x 80mm Bolt
20
DD
M5 x 25mm Screw
88

5 of 31
Letter
Illustration
Description
Qty.
EE
M4 x 35mm Screw
160
FF
M5 x 50mm Screw
48
GG
M5 x 30mm Screw
60
HH
M8 x 40mm Screw
16
II
M5 Washer
44
JJ
M8 Washer
52
KK
M10 Washer
16
LL
M8 Nut
26
MM
M10 Nut
16
NN
Open Wrench
2
OO
Allen Wrench
1

6 of 31
Assembly Instructions
Chesterfield 10.5’ x 10.5’ Pavilion
Important:
l Read all the instructions before assembly. Failure to do so may result in faulty assembly and
potential injury.
l Before assembling the product, remove all protective materials, hardware kit(s), and identify all
parts packed in the carton are present. (Note: If any part is missing or damaged, do not attempt to
assemble). Contact Shade N’ Shelters Customer Support. See page 31.
l Assemble on a stable level surface to avoid damage to gazebo and possible injury.
l Two people are required to assemble this product.
l Gazebo dimensions are measured from roof corner to roof corner.
WARNING: DO NOT TIGHTEN BOLTS UNTIL NOTED AFTER EACH STEP!
Roof Assembly Overview

7 of 31
Frame Assembly Overview

8 of 31
Step 1: Attach the Base Bracket (T) to the Post (A) using Screws (GG). See Figure 1.
Note: use the small holes on Base Bracket (T) when attaching to Post (A).
Figure 1

9 of 31
Step 2: Attach Crossbar Right Side (B1) to Crossbar Left Side B2 using Bolts (BB), Washers (JJ), Nuts (LL)
and Screws (FF). See Figure 2.
Note: Attach the bolts before the Screws.
Figure 2

10 of 31
Step 3: Attach Crossbar Right Side (C1) to Crossbar Left Side (C2) using Bolts (BB), Washers (JJ), Nuts
(LL) and Screws (FF). See Figure 3.
Note: Attach the bolts before the Screws.
Figure 3

11 of 31
Step 4: Attach the Posts (A) to the assembled crossbeam (B1 and B2) using Bolts (AA), Washers (KK), and
Nuts (MM). See Figure 4.
Note: Before attaching crossbeams (B1 and B2) make sure you are using the correct holes (Top
Holes) on Post (A). See closeup of Figure 4.
Note: Crossbeams (B1 and B2) must be facing the correct direction and all remaining holes must
be in the correct position (Up or Down). See Figure 4.
Figure 4

12 of 31
Step 5: Attach the Posts (A) to the assembled crossbeam (C1 and C2) using Bolts (AA), Washers (KK), and
Nuts (MM). See Figure 5.
Figure 5

13 of 31
Step 6A: Attach Corner Support Right (E1) t0 Crossbar Right Side (B1 & C1) using Bolts (CC), Washers (JJ)
and Nuts (LL). Attach Corner Support Right (E1) to Post (A) using Screws (HH) and Washers (JJ).
Step 6B: Attach Corner Support Left (E2) Crossbar Left Side (B2 & C2) using Bolts (CC), Washers (JJ) and
Nuts (LL). Attach Corner Support Left (E2) to Post (A) using Screws (HH) and Washers (JJ).
Figure 6

14 of 31
Step 7: Attach the Roof Rafter (D) to the inside of the assembled crossbeam (C1 and C2) using Bolts (CC),
Washers (JJ), and Nuts (LL). See Figure 7.
Figure 7

15 of 31
Figure 8-1
Step 8A: Attach the Connecting Rafter (K) to Side Rafter (G) using Screws (EE). Repeat for remaining pieces.
Tighten all Bolts. See Figure 8-1.
Step 8B: Attach the Connecting Rafter (K) to Roof Support Rafter (J) using Screws (EE). Repeat for
remaining pieces. Tighten all Bolts. See Figure 8-2.
Figure 8-2

16 of 31
Figure 9-1
Step 9: Attach the Connecting Rafter (K) to Roof Rafter (F1) and Roof Rafter (F2) using Screws (EE).
Repeat for remaining pieces. Tighten all Bolts. See Figure 9-1.
Note: See Figure 9-2 to make sure Connecting Rafter (K) is on the correct side of Roof Rafter (F1)
and Roof Rafter (F2).
Figure 9-2

17 of 31
Figure 10-2
Figure 10-4
Step 10A: Attach the Roof Rafter (H) to Side Rafter (G) using screws (EE). See Figure 10-1. Repeat for other
side.
Step 10B: Attach the Roof Rafter (H) to the Roof Rafter (F2) using Screws (EE). See Figure 10-2. Repeat for
other side.
Step 10C: Attach Roof Rafter (I) to the Side Rafter (G) and Roof Rafter (F1 and F2) using Screws (EE). See
Figure 10-3 and Figure 10-4.
Figure 10-1
Figure 10-3
Figure 10-1
Figure 10-3
Figure 10-2
Figure 10-4

18 of 31
Figure 11-1
Figure 11-2
Step 11: Attach the Roof Support Rafter (J) to Roof Rafter (H) and Roof Rafter (I) using Screws (EE). See
Figure 11-1 and Figure 11-2. Repeat for remaining Roof Support Rafter (J).
Figure 11

19 of 31
Figure 12-4
Figure 12-2
Figure 12-1
Figure 12-3
Step 12: Place the Roof Panels (P1 and P2) on top of the Roof Frame. The right panel must overlap the left
panel. See Figure. 12-2.

20 of 31
Figure 13-1
Step 13A: Attach the Roof Panel Trim (Q1 and Q2) to the sides of the Roof Frame using Screws (GG). See
Figure 13-1.
Note: The Roof Panels (P1 and P2) must slide into the Roof Panel Trim (Q1 and Q2).
Step 13B: Insert Roof Panel Trim (S2) into Roof Panel Trim (S1). See Figure 13-3.
Step 13C: Attach the Roof Panels (P1 and P2) to the Roof Frame using Screws (GG). See Figure 13-2.
Figure 13-2
Figure 13-3