Shadowspec RETREAT User manual

Shadowspec
RETREAT™
The Wall Mounted Umbrella
INSTALLATION GUIDE
Operation, Care and Warranty
www.shadowspec.com P01/22

Recommended Installation Height
1210mm/4’
440mm/1’5’’
310mm/1’
2340mm / 7’8’’
2700mm / 8’10’’
Shadowspec Retreat™ Dimensions
Shadowspec Retreat™
2160mm/7’1’’
1650mm/5’5’’ 2015mm/6’7’’
2470mm/8’1’’

www.shadowspec.com
What’s in the Box?
Read your manual in full before assembling your umbrella. To extend the life
of your umbrella investment please read and follow the care instrucons on
a regular basis.
This document contains all the informaon you need to install your
Shadowspec Retreat™
Thank you for your purchase, we appreciate it.
Enjoy the shade, courtesy of Shadowspec.
Retreat Arm Assembly
Top Wall Bracket
Frame Assembly
Canopy &
Protecon Cover
Boom Catch Bracket
Spring Cup
C-Clip
Welcome
www.shadowspec.com

1210mm/4’
440mm/1’5’’
1650mm/5’5’’
Ground Level
Wall Mount Bracket Installation
1. Install the Top Wall Bracket
#14/18 x 75mm Hex Flange
Screw Qty. 3
Post
#14/18 x 75mm Hex Flange
Screw Qty. 3
Wood
8mm Expansion Bolt Qty. 3
Concrete
#12 x 50mm Flange Screw QTY. 2
Or
6mm Expansion Bolt QTY. 2
Recommended Height & Spacing
Fig. A Fig. B Fig. C
Fig. D Fig. E
2. Mounng the Boom Catch
Insert the Arm Retainer to the
Boom Catch Bracket with the
End Plate Screw
3. Mounng the Spring Cup
Slide the Spring Cup into the Top
Wall Bracket and nger-ghten
the screw.
End
Plate
Screw
Top Wall
Bracket
Bolt Holes
Arm
Retainer
Top Wall
Bracket
Spring
Cup
Boom
Catch
Bracket
Shadowspec Retreat™
i: Choose a wall, pillar or post that is strong enough to mount the Retreat
ii: Choose a 316 Stainless Steel Fastener that matches your structure. Fig. A.
iii: Using the Top Wall Bracket as a guide, mark holes on your wall at the desired height. Fig. B.
We recommend 2205mm/7’3’’ measured from the top of the Top Wall Bracket to the Ground
iv. Ax the Top Wall Bracket to the structure using the correct xing opon. Fig. A.
v. Ax the Boom Catch to the structure using the correct xing opon. Fig. C.

Shadowspec Retreat™ Installation
4. Mount the Arm Assembly
Retreat Arm
Shoulder
Fixing
Bolts
Wall Grab Plate
Fig. F
Fig. H
Fig. K Fig. L Fig. M
Fig. I
Fig. J
Fig. G
www.shadowspec.com
i: Loosen the Shoulder Fixing Bolts so they do not restrict the Wall Grab Plate. Fig. F.
ii: Lower the Retreat Arm into the Wall Mount Bracket unl it seles in place. Fig. G.
iii: Fully Tighten the Shoulder Fixing Bolts.
iv: Pull the Shoulder Locking Pin. Fig. H.
v. Push the Retreat Arm upward. Fig. I.
vi. Swing the Gas Piston into the Spring Cup. Fig. J.
vii. Lower Retreat Arm and push the Spring Cup Up to align with the marks on the Wall Mount. Fig. K.
viii: Fully ghten the Spring Cup Bolt with supplied Hex Wrench. Fig. L.
ix: Insert the C-Clip into the channel and twist to lock into place. Fig. M.
Important: The Gas Spring’s pressure is now engaged - take extreme care and ax the frame straight away.

Shadowspec Retreat™ Installation
5. Fit the Canopy Frame
Fig. N
Fig. P
Fig. O
Fig. Q
Shadowspec Retreat™
i. Pull the Claw Latch Lever to open it. Fig. N / Fig. O.
ii. The Grab Latch will detach from the Bracket Fig. P / Fig. Q.
iii. Insert the Canopy Frame into the Claw Bracket Fig. R.
Tip: Ensure the Canopy Notch ts into the front of the Claw Assembly
iv. Hook the Grab Latch into the Claw Notch and reverse the opening process to secure.
Fig. Q > Fig. N.

Fig. N
Fig. P
Fig. O
Fig. Q (Reversed) (Reversed)
(Reversed) (Reversed)
Fig. R Fig. S
www.shadowspec.com

www.shadowspec.com
Shadowspec Retreat™ Canopy Fitting
6. Fit Fabric Canopy
1: Pull the Shoulder Locking Pin. Fig. T:
2. Push downward the unl it locks in the angled posion. Fig. U.
Tip: Take care as the Gas Spring will require some force to compress and the arm may swing up
before it locks into place.
3. Remove the Crown by removing the 2 Crown Screws. Fig. V.
4. Drape the Fabric Canopy over the Canopy Frame and insert the Rib Tips into the corelang Fabric Pockets.
Fig. W.
5. Return the Crown and Crown Screws on top of the Canopy. Fig. X.
6. Deploy and Enjoy!
Fig. T
Fig. V
Fig. U
Fig. W
Fig. X: