Shanty 2 CHIC Round Table User manual

Round Table
ell suited for intimate settings this pedestal dining table will
be admired for years to come. Sturdy legs and top will make
it feel right at home in most any setting.
W
Copyright © 2015 Shanty-2-Chic.com

Round Table - Page | 2SHanty-2-Chic.com
Materials needed Qty
1” X 6” X 8’ Pine 5
1” x 8” x 8’ Pine 1
1” x 3” x 8’ Pine 1
2” x 3” x 8’ Pine 1
2” x 6” x 8’ Pine 1
2-5/8” x 6’ case molding 1
1/2” x 6’ cove molding 1
1-1/4” pocket screws
1-1/4” brad nails
#10 x 2-1/4” wood screw 4
wood glue
DETAILS
CUT LIST MATERIALS LIST
Part Qty Part Name Dimension
A 5 Table top slats 1” x 6” x 48”
B 2 Table top slats 1” x 6” x 40”
C 2 Table top slats 1” x 6” x 32”
D 2 Base box wide 1” x 8” x 30-14”
E 2 Base box narrow 1” x 6” x 30-1/4””
F 2 Table top supports 2” x 3” x 44 *
G 4 Feet 2” x 6” x 14-1/4”
H 4 Feet pads 1” x 6” x 5-1/2”
I 4 Feet caps 1” x 6” x 6”
J 2
each
1x6 moulding 1” x 6” x 9”, 7” *
K 2
each
1x3 moulding 1” x 3” x 10-1/2”, 8-1/2” *
L 2
each
case moulding 2-5/8” x *
M 2
each
cove moulding 1/2” x *
* Final length determined by setting board in place and marking for length
Feet
Decorative Edge
F
approx. 1/2”
approx. 45˚
Feet Pads &
Feet Caps
G
IH

Round Table - Page | 3SHanty-2-Chic.com
1.
To begin, construct the top out of 9 - 1x6 boards cut to length as shown in the cutting diagram.
Place all the boards top face down. Attach the planks to each other, the outer pieces
off set by 4” as shown, with 1-1/4” pocket screws.
To cut the circle top fi rst locate the center and gently tap a temporary nail in the board.
Attach a piece of string from the nail to a pencil so that the pencil, when taught,
reaches just to the edge of the middle board and draw a circle as shown.
Remove the nail and cut along the drawn circle with a jigsaw.
Sand the rough edges with 120 grit sandpaper
2.
To form the base attach 1x8 and 1x6 boards as shown, making sure the 1x6 sits inside
the 1x8 and all edges are fl ush. Checking to make sure the corners are square as you go
attach with glue and 1-1/4” brad nails.
3.
Using the base box as a guide lay the table top supports in place. Mark the supports so that they will sit
about 2” in from the table edge and trim. Attach the table top supports with 1-14” pocket screws and glue.
DO NOT ATTACH THE BASE BOX YET.
2
1
A A A A A B CBC
3
width
of box
D
D
E
E
F
F

Round Table - Page | 4SHanty-2-Chic.com
4.
For the feet cut the 45º angles as shown on page 2. Attach the feet pads to the feet with 1-1/4” brad nails and glue.
Repeat this step for the remaining three feet.
Center the feet on the base box and attach with 1-1/4” pocket screws and glue, off setting the feet 3/4” from
the bottom so that the base box and the foot pads sit fl ush on the ground.
5.
Attach feet caps with 1-1/4” brad nails and glue.
6.
The most accurate way to attach trim is to hold the material in place, mark the length with a pencil and then trim to fi t.
Do this for the 1x6 and 1x3 blocking. Attach with glue and 1-1/4” brad nails
Repeat this method for the case molding and cove molding; only the molding will be mitered in the corner.
First the case molding is attached on top of the 1x3 blocking. Then attach the cove molding on top of the 1x6 moulding
and at the base of the 1x3 moulding.
Repeat, but invert, the entire trim process with the top of the base box.
Begin 2-1/2” down from the top to accommodate for the table top supports.
5
4
G
H
6
I I
J
L
J
L
I
I
K
M
K
M
2-1/2”
J K L M

Round Table - Page | 5SHanty-2-Chic.com
7.
Before you attach the top to the base it is easiest to execute your fi nishing now.
Attach the table top to the base with 2-1/4” wood screws.
Center the table top on the base and drive the screws through the 2x3’s into the base box.
7