Shanty 2 CHIC DIY FARMHOUSE DINING BENCH User manual

Stafford Pine Dining set: Bench - Page | 2SHanty-2-Chic.com
2" x 4" x 8'
2" x 4" x 8'
2" x 4" x 8'
2" x 4" x 8'
2" x 4" x 8'
2" x 4" x 8'
2" x 4" x 8'
2" x 4" x 8'
CUT LIST
Make sure you read through the instructions carefully and take notice of any special
construction notes prior to making any cuts. And always practice safe DIY’ing. Have fun!
PLEASE NOTE - many pieces may require you to cut them to t a certain size
while you are building it. Its best not to cut pieces until you need them. Take
your time and study all the diagrams.

Stafford Pine Dining set: Bench - Page | 3SHanty-2-Chic.com
Material Qty
2” X 4" X 8’ wall stud 8
NOTES
MATERIALS LIST
Material Qty
2-½” pocket screws
2-½” brad nails
2-½” SPAX wood screws
wood glue

Stafford Pine Dining set: Bench - Page | 4SHanty-2-Chic.com
3"
3"
13 ½"
7 ½"
½"
1 ¾"
1 ¾"
Bevels on both
sides cut at 45º.
2
1" 62"
4 ½"
3 ½"
3"
1 ½"
2 x 4
1.
For a slightly more sophisticated look we will be ripping the rounded
edges o the 2x4 lumber. For consistency sake rip all boards at the
same time so you know all the boards are exactly 3" wide.
First rip just enough o of one side of all the 2x4 boards to remove
the rounded edges. Then, set your table saw fence at 3" and rip the
other rounded side o. Repeat for the rest of your boards.
2.
Now we will form the two leg assemblies.
First cut the two different lengths of the green feet, the upper
length at 12 ½" and the lower at 15". Cut two of each. Then,
using the above illustration, cut the 45º bevel as shown.
Now cut the orange vertical leg supports to length. Each leg
assembly will have a shorter green board on top and a longer on
the bottom. Dab some glue on the ends of the orange vertical
leg supports and clamp the boards together so that the vertical
boards are offset as shown and side edges flush. The bevels of
the upper and lower feet will face towards each other. Check for
square. Attach with 2-½" SPAX screws.
Repeat for second assembly.
3.
Cut three red stretcher boards to 62". Drill 1-½" pocket holes into
both ends of each board. Save one board for Step 4.
First we will attach the two stretchers that will end up being the
top to the shorter green feet. The stretchers will be 1" from the
outer edges of the leg assemblies as shown, attach with wood
glue and 2-½" pocket screws. Make sure the top and bottom
edges are as ush as possible.
1
X 2
½"
½"
½"
½"
12 ½"
½"
½"
½"
½"
15"
3Long Board
Short Board
X 2
X 2

Stafford Pine Dining set: Bench - Page | 5SHanty-2-Chic.com
78"
6"
6"
1 ¼"
1 ¼"
8" 8"
5
4.
Center the third stretcher as shown, making sure the top and bottom
surfaces are as ush as possible as this will be the bottom of your
bench and you don't want it to rock. Attach with wood glue and
2-½" pocket screws.
The safest way to cut the small yellow feet is to cut the bevel
(same as Step 2 but only into one end) and then cut it to length.
Repeat for second foot. Clamp in place, centered, as shown and
attach with wood glue and 2-½" brad nails.
5.
Now we will plank the remaining boards to form the seat of your
bench. Cut your long blue boards to length and drill 1-½" pocket
holes as shown. For even pressure distribution from the pocket
screws we like to stagger the pocket holes so that the screws 'pull'
the boards together evenly. Attach with wood glue and 2-½"
pocket screws. Make sure the boards are as ush as possible.
Measure the width of your planked boards, it should be about
15". Cut your purple breadboards (those that run perpendicular
to the long boards and cap the ends of your bench seat) to that
length. Drill 1-½" pocket holes and attach with wood glue and
2-½" pocket screws. Make sure boards are as ush as possible.
6.
Now all we have to do is attach the leg assembly to the bench seat.
Lay the top on a clean surface with the pocket holes facing up.
Lay the leg assembly on top, centered as shown in the illustration
above. Make sure the leg assembly is set in place with the double
stretchers connecting to the seat and the single stretcher is facing
up. Clamp in place so nothing shifts and attach with 2-½" SPAX
screws. We don't use wood glue here because you want to allow
for the wood to expand and contract so use plenty of screws but
be careful that you don't drive them too far and they come out the
other side of the bench seat. Also, make sure you don't drive them
into a pocket screw or a seam between the long blue boards.
4
6
1 ½"
1 ½"
3"
3"
3"
3"
15"
Small feet are 3 ¾"
long. Cut bevel into
one end only.