Shark HC500 Series User manual

Read and review instructions for
operation and use.
Indicates the presence of a hazard
that can cause personal injury, death,
or substantial property damage if the
warning included with this symbol is
ignored.
For indoor and household use only.
Shark Air Purifier 3-in-1
HC500/450 Series
OWNER’S GUIDE
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be followed, including the following:
HOUSEHOLD USE ONLY
WARNING
1. Read all instructions before use.
2. This appliance has a polarized plug (one blade is wider than the other).
To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician.
DO NOT attempt to defeat this safety feature. Unplug or disconnect
the appliance from the power supply before servicing.
3. DO NOT operate any appliance with a damaged cord or plug. Discard
appliance or return to an authorized service facility for examination
and/or repair.
4. DO NOT run cord under carpeting. DO NOT cover cord with throw
rugs, runners, or similar coverings. DO NOT route cord under furniture
or appliances. Keep cord away from high traffic areas and place cord
where it will not be tripped over.
5. If the power cord is damaged, it must be replaced by the manufacturer,
its service agent, or similarly qualified persons in order to avoid a hazard.
6. This appliance is not intended for use by anyone (including children)
with reduced physical, sensory, or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
7. Children should be supervised to ensure that they DO NOT play with
the appliance.
8. Cleaning and user maintenance shall not be made by children
without supervision.
9. Prior to cleaning or other maintenance, the appliance must be unplugged
from the electrical outlet.
10. DO NOT handle plug or appliance with wet hands.
11. DO NOT use without filter in place.
12. Only use Shark® branded filters and accessories.
13. DO NOT damage the power cord:
a) DO NOT pull or carry appliance by the cord or use the cord as a handle.
b) DO NOT unplug by pulling on cord. Grasp the plug, not the cord.
c) DO NOT stand the appliance on the power cord, close a door on
the cord, pull the cord around sharp corners, or leave the cord near
heated surfaces.
14. DO NOT use with any opening blocked; keep free of dust, lint, hair, and
anything that may reduce airflow.
15. DO NOT use if airflow is restricted. If the air paths become blocked,
turn the appliance off and unplug from electrical outlet. Remove all
obstructions before you plug in and turn on the unit again.
16. DO NOT use if appliance is not working as it should, or has been
dropped, damaged, left outdoors, or dropped into water.
17. DO NOT place appliance on unstable surfaces such as chairs or
other furniture.
18. DO NOT use in the following areas:
a) Wet or damp surfaces
b) Outdoor areas
c) Spaces that are enclosed and may contain explosive or toxic
fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint
thinners, mothproofing substances, or flammable dust)
19. Turn off all controls before unplugging the appliance.
20. Unplug from electrical outlet when not in use and before any
maintenance or cleaning.
21. Hand wash with soapy water only. Washing with cleaning chemicals
could damage the unit.
22. Make sure filter is in place after routine maintenance.
23. Not suitable for use with solid-state speed controls.
IMPORTANT INSTRUCTIONS
24. This heater is hot when in use. To avoid burns, DO NOT let bare skin
touch hot surfaces. If provided, use handles when moving this heater.
Keep combustible materials, such as furniture, pillows, bedding, papers,
clothes, and curtains at least 3 feet (0.9m) from the front of the heater
and keep them away from the sides and rear.
25. Extreme caution is necessary when any heater is used by or near
children or persons with disabilities and whenever the heater is left
operating and unattended.
26. This heater is not intended for use in bathrooms, laundry areas, or
other high moisture locations. Never locate heater where it may fall into
a bathtub or other water container.
27. DO NOT insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or damage
the heater.
28. To prevent a possible fire, DO NOT block air intakes or exhaust in any
manner. DO NOT use on soft surfaces, like a bed, where openings may
become blocked.
29. A heater has hot, arcing and/or sparking parts inside. DO NOT use it in
areas where gasoline, paint, or flammable liquids are used or stored.
30. Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or
injury to persons.
31. Always plug heaters directly into a wall outlet/receptacle. Never use
with an extension cord or relocatable power tap (outlet/power strip).
WARNING: LITHIUM BATTERY
32. Dispose of coin cell batteries according to local regulations. Keep
batteries away from children at all times. Even used batteries can
cause injury.
Chemical Burn Hazard. Keep batteries away from children.
This product contains a lithium button/coin cell battery. If a new or
used lithium button/coin cell battery is swallowed or enters the body,
it can cause severe internal burns and can lead to death in as little as
2 hours. After changing batteries, always completely close and secure
the battery compartment. If the battery compartment does not close
securely, stop using the product, remove the battery, and keep it away
from children. If you think battery might have been swallowed or placed
inside any part of the body, seek immediate medical attention.
SCAN FOR
ADDITIONAL
RESOURCES
OR VISIT
qr.sharkclean.com/
hc500series
SAVE THESE INSTRUCTIONS

SETTING UP YOUR AIR PURIFIER
Parts:
1. Remote Dock
2. Power Button
3. Front Vents
4. Air Angle Adjustment Tab
5. Mode Dial
6. Display
7. Unit Base
8. Back Vents
9. Shark NanoSeal™ HEPA Filter
10. Filter Door
11. Remote
1
4
10
6
7
9
3
8
5
TIPS FOR SETTING
UP YOUR AIR PURIFIER
• Make sure the front panel product faces away
from the closest wall.
• Do not move the unit while it is running. Turn
o the power and unplug the air purifier before
moving it.
• Make sure the air intake vents are not blocked.
• Do not place anything on the air purifier.
• Do not place the air purifier near heaters or
radiators.
• Keep the air purifier out of direct sunlight and
away from water or other liquid.
• Keep all nearby doors and windows closed
when operating the air purifier.
• Avoid using in very humid environments.
1
2
2
11
3 feet
minimum
4
32
Remove filter
from plastic
packaging
5 6
1
1. You must remove the filter and take it
out of its packaging before operating.
First, remove the filter cover and filter
from the back of the air purifier.
2. Take the filter out of its sealed plastic
packaging. Slide filter back into the
air purifier.
3. Reinstall the filter cover. Insert the tabs
on the bottom of the cover into the slots.
Press the top and sides of the cover until
it clicks into place.
4. Set up the air purifier on a level floor
surface at least 3 feet (0.9m) from the
wall and any furnishings.
When carrying the air purifier, hold it
below the venting area. Do not put
your hands inside the vents
5. Plug the unit into an electrical outlet
and press the power button on the top
control panel OR on the removable
remote.
6. When the air purifier is powered on,
it will begin to analyze the air quality,
indicated by the rotating lights.
After a few seconds, the air purifier will
display the current air quality and room
temperature. From there, use the remote
and dial to customize the settings.
Back of
air purifier
Angle filter
cover to
align tabs at
the bottom
SETTING UP YOUR AIR PURIFIER

REMOTE
You can use the removable remote control to customize the settings.
Power on/o
Heating
Controls
Timer
Fan
Controls
Brightness
AUTO Mode
Air Info
Oscillation
REMOTE BUTTONS
MAX
On/O: Press to turn the power on or o.
MAX
AUTO mode: Press to turn on AUTO mode. The fan speed
automatically adjusts, based on the air quality. As the air quality
improves, the fan speed will decrease. If air quality worsens, the
fan speed will increase. Leave your air purifier in AUTO mode for
optimal filter life and performance. AUTO mode is only available
in PURIFIED AIR mode.
Optimize Performance in ECO mode: After the air is 100% clean for
10 minutes, the air purifier will enter ECO mode and will appear
on the display. This reduces power draw and optimizes the filter life.
Air Info: Press to switch between air quality display options.
See the Air Info Settings section for more information.
Fan Controls: Use the arrows to adjust the fan speed from 1-6.
Press the fan button to view the speed setting. Fan speed can be
adjusted in all 3 modes.
Note: When using AUTO mode, if fan speed is manually changed,
AUTO mode will be deactivated. For tips on optimal fan setting, see
Optimizing Fan Speed section.
Heater Controls: Press the Thermometer button to turn HEAT on/o.
Target Temperature: Use the arrows to adjust the target
temperature. The heater will automatically work to reach and
maintain the target. The air purifier will beep when the target
temperature is reached.
HI HEAT Mode: To run the heater in HI HEAT mode without
selecting a target temperature, press and hold the right-side
temperature arrow until HI appears on the display. For more tips on
optimizing heater performance, see the Heater Operation section.
MAX
Shut-O Timer: Set the number of hours for the air purifier to
run before it automatically shuts o. Timer can be set from
1–12 hours.
MAX
Brightness: Press to dim the brightness of the display. Switch
between 3 options: full brightness, partially dim, or fully dim.
Oscillation: Press to turn the oscillation on or o. When oscillating,
the unit will rotate side to side to distribute airflow around the room.
REMOTE SHORTCUTS
Turn O Sound: To turn o sounds, press and hold
the Brightness button for 3 seconds.
Turn On/O Child Safety Lock: Press and hold the Timer
and Oscillation buttons to turn the Child Safety Lock on or
o. The Lock icon will appear on the front display when
the lock is activated.
Change Temperature Display from Fahrenheit
to Celsius: Press and hold Fan and Thermometer buttons to
change the temperature display from Fahrenheit to Celsius.
Reset Filter Life: Press and hold the info button for
3 seconds to reset the Filter Life display after changing
the filter.
MODE DIAL
Turn the dial to change modes.
1. PURIFIED FAN
To operate FAN mode, turn the dial to the Fan icon. In this mode,
purified air will be directed out of the front vents.
2. PURIFIED HEAT
To operate HEAT mode, turn the dial to the Air icon. Then press
the Thermometer button on remote. In this mode, purified,
warm air will be directed out of the front vents.
3. PURIFIED AIR
To operate PURIFIED AIR mode, turn the mode dial to the Air icon.
In this mode, purified air will be diused out the back vents. This
allows for continuous air purification without the breeze of a fan.
While the air will be purified in all modes, PURIFIED AIR mode
boosts cleaning power.
PURIFIED AIR mode is compatible with AUTO and ECO modes.
Dial in FAN or HEAT Mode
Dial in PURIFIED AIR Mode
Air directed out of the FRONT
Air diused out of the BACK

MODE DISPLAYS
THE INFORMATION ON THE FRONT DISPLAY IS DIFFERENT IN EACH MODE.
UNDERSTANDING YOUR AIR QUALITY
The ring around the display will change color as the air quality changes, for easy monitoring from far away.
GOOD
85–100%
0–25
particles
.
FAIR
70–84%
26–80
particles
POOR
0–69%
81–430+
particles
Note: The air quality sensor uses a cumulative particle count across all particle sizes to determine percentage of clean air.R
AIR INFO SETTINGS
The built-in sensor detects your air quality to give you real-time information. Use the AIR INFO button to switch between settings.
INFO REAL-TIME READING
% CLEAN AIR Displays the air quality rating: • Poor: 0%–69%• Fair: 70%–84%• Good: 85%–100%
% CLEAN AIR uses particulate matter (PM) Air Quality Standards as determined by the EPA to calculate the air quality rating.
TIME TO CLEAN Shows the estimated time remaining until your air is clean.
PARTICLE SIZES The PM (particulate matter) value is the amount of particulate in your air, measured in micrograms
(g) per cubic meter. Your air purifier measures three particle sizes, PM1, PM2.5, and PM10.
PM1 Displays the amount of PM1-sized particles in your air, including ultra-fine allergens.
PM2.5 Displays the amount of PM2.5-sized particles in your air, including smoke.
PM10 Displays the amount of PM10-sized particles in your air, including dust, mold, and pollen.
ROOM TEMPERATURE Displays the current temperature in the room. *Only visible in PURIFIED AIR mode
FILTER LIFE Displays the remaining filter life, as a percentage.
To improve FAIR or POOR air quality increase the fan speed or select AUTO mode.
PURIFIED FAN
The top reading is the clean air
percentage and the bottom reading
is the current room temperature.
PURIFIED HEAT
In this mode, the top reading is the clean
air percentage and the bottom reading in
red is the target temperature. Once the
target temperature is reached, the bottom
reading will display the current room
temperature in white.
PURIFIED AIR
In this mode, the percentage
of clean air is shown.
The red thermometer light indicates
that the heater is on and warming
to reach the target temperature.
MAX
MAX
MAX

AIR PURIFIER OPERATION
TO ACTIVATE PURIFIED AIR MODE AND ADJUST SETTINGS:
1. Turn the mode dial to the Air icon.
2. The display will show air quality as a percentage. Press
the info button to change the air information displayed.
3. Press the fan arrows to adjust the fan speed. As fan speed
increases, so will purification performance.
4.To activate AUTO mode, press the AUTO button. In this mode,
the fan speed will automatically adjust, based on the quality of
the air. AUTO mode is only available in PURIFIED AIR mode.
5. When in AUTO mode, if the air is 100% clean for 10 minutes,
the air purifier will enter ECO mode and will appear on the
display. This will reduce energy consumption and extend the
filter life.
FAN OPERATION
TO ACTIVATE THE FAN AND ADJUST AIRFLOW:
1. Turn the mode dial to the Fan icon.
2. On the front display, the top number is the clean air percentage
and the bottom number is the current room temperature.
Press the Info button to change the air information
displayed.
3. Press the fan arrows to adjust the fan speed or press the
Fan button to check current fan speed. As fan speed
increases, so will purification performance.
4.Press the Oscillation button on the remote to turn
oscillation on or off.
5. Additionally, the airflow angle can be adjusted by moving the
front vents up or down.
NIGHT USE
For non-disruptive performance at night:
• Lower the fan speed for soothing white noise.
• Press the Brightness button to fully dim the display.
• Turn on oscillation for better fan coverage.
• Press and hold the Brightness button for 3 seconds to
turn sound off or on.
52-4
2-4
1
1
TIPS FOR USING PURIFIED AIR MODE:
Air quality fluctuates, depending on what is introduced in the
home. Some factors that can affect the air quality:
• Cooking or burning food
• Vacuuming or dusting
• Spraying cleaning products
• Smoking
• Opening windows or exterior
doors can introduce pollen.
Leave the air purifier in AUTO mode for optimal filter life
and performance.
AUTO mode is ONLY available in PURIFIED AIR mode.
2
2
3
3
4
4
5

HEATER OPERATION
TO ACTIVATE THE HEATER AND ADJUST SETTINGS:
1. Turn the mode dial to the Heat icon and press to turn on heat.
2. On the front display, the top number is the clean air percentage.
The bottom number in red is the target temperature.
3. Press the temperature arrows to set the target temperature or
hold down the right arrow for HI heat mode. When the target
temperature is set, the display will flash and beep twice
to confirm.
Note: The heater may need up to 25 seconds to fully warm up.
This will be indicated by the red ‘heating up’ animation.
4.After the target temperature is set and the heater is active,
the bottom number in the display will turn white and will
update to show current room temperature.
5. When the target temperature is reached, there will be a long
beep, and heating will pause.
6.Use the fan arrows to adjust the heated air flow rate.
7. Press the Info button to change the air information display.
8. Press the Oscillation icon to turn oscillation on or off.
9. Additionally, the airflow angle can be adjusted by moving
the front vents up or down.
3
2
6-8
1
4TIPS FOR USING PURIFIED HEAT MODE
• When using the air purifier at close
range for personal heating, lower the
fan speed for optimal performance.
• When using the air purifier at a distance
for whole-room heating, increase the
fan speed and turn on oscillation for
optimal performance.
• In HI heat mode, the heater will not have
a temperature target and will continue
to run until turned off.
7
6
8
HEATER SAFETY FUNCTION AND RESET
The air purifier has multiple safety features designed to prevent overheating, accidents, and damage.
TIP-OVER AUTOMATIC SHUTOFF
If your air purifier gets tipped over, it will automatically turn off.
Follow these steps to reactivate the heater:
1. Turn the power off and unplug the air purifier.
2. Set the air purifier upright, on a level floor surface.
3. Plug in the air purifier and turn on power.
4. Turn the mode dial to the Heat icon and press to turn on heat.
OVERHEAT AUTOMATIC SHUTOFF
Your air purifier could overheat if obstructions block the vents.
If this happens, the unit will automatically turn off. Follow these
steps to reactivate the heater:
1. Turn the power off and unplug the air purifier.
2. Remove any obstructions from the vents.
3. Wait 5 minutes, then plug in the air purifier and turn on power.
4. Turn the mode dial to the Heat icon and press to turn on heat.
Note: Any rattling heard when moving
the air purifier may be caused by
the internal safety tilt switch.

INSTALLING AND REMOVING THE FILTER
NOTE: Always remove all protective packaging from the filter before installing.
Shark® filters are engineered to last between 6-12 months. When the filter life has 0% remaining, FILTER LIFE will illuminate and flash,
indicating that it’s time to install a new filter.
1. Turn o and unplug the air purifier before removing or
installing filters.
2. First, remove the filter cover from the back of the air purifier.
Use the handle to pull the filter door towards you.
3. To remove the old filter, pull it out by the removal tabs.
Discard old filter in trash.
4. Remove all packaging and wrapping from the new filter.
5. Insert the new filter, then replace the filter cover. Insert the tabs
on the bottom of the cover into the slots. Press the top and sides
of the cover until it clicks into place.
6. Plug the air purifier back on and turn on power.
Calibration will begin.
7. After installing a new filter, press and hold the Info button
for 3 seconds to reset the filter life percentage. The air purifier
will beep to confirm when the filter life is reset to 100%.
Disposing of used filters
Filters can’t be cleaned or recycled. After removing a used filter, wrap it in an airtight
plastic bag for disposal. As an extra precaution, wear gloves when handling a dirty filter.
To maximize filter life, every three months, remove the filter, then turn it upside down
and reinstall it. This will help equalize and balance the distribution of captured particles
throughout the filter, allowing for extended use.
MAINTAINING YOUR AIR PURIFIER
NOTE: Always unplug the unit before doing any cleaning or maintenance.
Exterior Cleaning:
For best results, clean the exterior every two months or as needed.
Use a microfiber cloth to remove dust. To clean, wipe down the
exterior with a microfiber cloth dampened with warm, soapy
water. Avoid excess water and abrasive chemical cleaners to
prevent damage.
Interior Cleaning:
For best results, clean the interior of the air purifier every two
months or as needed. Remove the filter door, take out the filter,
and use a vacuum cleaner or a microfiber cloth to remove dust
and debris from the interior. DO NOT use abrasive chemical
cleaners on the inside of the air purifier.
3
Remove
filter
from
plastic
packaging
2
1

REPLACING THE REMOTE BATTERY
The removable remote is equipped with a CR2025 lithium coin cell battery with a life of up to 3 years. Periodically, the remote battery will
require replacement.
1. Remove the remote from its dock on the top of the air purifier.
2 Pinch the tab on the battery compartment, then slide out
the compartment.
3. Remove the battery and dispose of it immediately.
Keep the battery away from children and pets.
4. Insert a new battery, (+) side facing up. Then slide the battery
compartment back into the remote, until it clicks into place.
5. Point the remote at the air purifier and adjust the settings to
ensure the remote is functioning properly. If there are persisting issues
with the remote, see the Troubleshooting section.
AVAILABLE ACCESSORIES
ORDER ADDITIONAL ACCESSORIES AND REPLACEMENT FILTERS
from sharkaccessories.com
SHARK NANOSEAL™ BASE FILTER WITH TRUE HEPA
Captures 99.98% of large, small, and micro-sized particles
from the air and is equipped with carbon for heightened
protection against household odors and VOCs.
SHARK® HC500/450 SERIES REMOTE CONTROL.
3
2
1

TROUBLESHOOTING
ERROR CODE MEANING SOLUTION
AUTO mode is not available
in Purified Heat or Fan mode.
• Make sure the mode dial on the side of
the air purifier is pointing to the Air icon.
• Then press AUTO on the remote to
activate AUTO mode.
The heater is not active
OR
purified heat is not available in this mode.
• Make sure the mode dial on the side of the
air purifier is pointing to the Heat icon.
• Then press on the remote to turn on
PURIFIED HEAT mode.
PROBLEM SOLUTION
My air purifier is not powering on,
what should I do?
• Make sure the air purifier is set up on a flat, level floor surface. Plug it in and ensure that the outlet works.
Press the power button to turn the air purifier on.
• Make sure the filter cover is properly installed in the back of the air purifier. Insert the tabs on the bottom of
the cover into the slots. Press the top and sides of the cover until it clicks into place.
• Make sure filter is installed fully in the unit. Push filter into the unit firmly until the filter cannot be pushed
back any more.
I can’t feel air blowing out of the
front of the air purifier.
• For PURIFIED FAN mode, make sure the mode dial on the side of the air purifier is pointing to the Fan icon.
This will direct air out of the front vents.
• For PURIFIED AIR mode, make sure the mode dial on the side of the air purifier is pointing to the Air icon.
This will direct air out of the back vents.
• Make sure the filter has been removed from its packaging.
How do I know when my
air purifier is in AUTO mode?
• The icon on the display illuminates when the air purifier is in AUTO mode. AUTO mode is ONLY available
in PURIFIED AIR mode.
• For PURIFIED AIR mode, make sure the mode dial on the side of the air purifier is pointing to the Air icon.
I can’t turn the heater on. • Make sure the mode dial on the side of the air purifier is pointing to the Heat icon.
• Press the Heat icon on the remote to turn on PURIFIED HEAT mode.
My heater turned o on its own.
• Once a target temperature is set, the heater will work to achieve it. After the target is reached, the heater
will monitor the temperature in the room and turn back on if the room temperature falls below the target.
• The heater has built-in safety features designed to prevent overheating, accidents, and damage. If your
heater has malfunctioned, follow the steps in the Heater Safety Function and Reset section.
How do I change the temperature
display from Fahrenheit to Celsius?
• Simultaneously press and hold Fan and Thermometer buttons to change the temperature
measurement display from Fahrenheit to Celsius.
Why does my air smell bad?
• Make sure the filter has been removed from its packaging.
• If your air purifier is brand new, there may be an initial electronic smell that will go away on its own.
• If there have been odors in the area recently, such as from cigarettes or food, allow more time for the air
purifier to remove them.
• Clean o any dust or debris from the intake vent and air vent areas.
• The filter may need to be replaced.
Can I wash the filter? • No, the filter is not washable. Keep filter away from water and dispose of it when it is dirty.
How do I turn o the beeping? • To turn sound on or o, press and hold the Brightness button for three seconds.
Why is my air purifier vibrating
or making unusual loud noises? • Make sure the air purifier is set up on its base and on a flat, level space on the floor.
My remote is not working.
• Make sure the Child Safety Lock is not activated, indicated by the Lock icon on the display.
• To turn on/o Child Lock, simultaneously press and hold the Timer and Oscillation buttons.
• Try replacing the remote battery. For instructions, see Replacing the Remote Battery’ section.
Customer Service
For further assistance, call 1-855-523-4061.

TWO (2) YEAR LIMITED WARRANTY
The Two (2) Year Limited Warranty applies to purchases made from
authorized retailers of SharkNinja Operating LLC. Warranty coverage
applies to the original owner and to the original product only and is
not transferable.
SharkNinja warrants that the unit shall be free from defects in material and
workmanship for a period of two (2) years from the date of purchase when
it is used under normal household conditions and maintained according to
the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original air purifier and/or non-wearable parts deemed defective, in
SharkNinja’s sole discretion, will be repaired or replaced up to two (2)
years from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends
six (6) months following the receipt date of the replacement unit or
the remainder of the existing warranty, whichever is later. SharkNinja
reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as filters and batteries,
etc.), which require regular maintenance and/or replacement to ensure
the proper functioning of your unit, are not covered by this warranty.
Replacement parts are available for purchase at sharkaccessories.com.
2. Any air purifier that has been tampered with or used for
commercial purposes.
3. Damage caused by misuse, abuse, negligent handling, failure to
perform required maintenance (e.g., not replacing the filters), or
damage due to mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These
defects include damages caused in the process of shipping, altering, or
repairing the SharkNinja product (or any of its parts) when the repair is
performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your air purifier fails to operate properly while in use under normal
household conditions within the warranty period, visit sharkclean.com/
support for product care and maintenance self-help. Our Customer
Service Specialists are also available at 1-855-523-4061 to assist with
product support and warranty service options, including the possibility of
upgrading to our VIP warranty service options for select product categories.
So we may better assist you, please register your product online at
registeryourshark.com and have the product on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for
repair or replacement. A fee of $25.95 (subject to change) will be charged
when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-855-523-4061 to initiate a warranty claim. You will need the
receipt as proof of purchase. We also ask that you register your product
online at registeryourshark.com and have the product on hand when you
call, so we may better assist you. A Customer Service Specialist will provide
you with return and packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other
rights that vary from state to state. Some states do not permit the exclusion
or limitation of incidental or consequential damages, so the above may not
apply to you.
IMPORTANT INFORMATION
REGISTER YOUR PURCHASE
registeryourshark.com
Scan QR code using
mobile device
RECORD THIS INFORMATION
Model Number:
�����������������������������������������������������������������������������������������������������������������������������������������������������������������������������
Serial Number: �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
Date of Purchase: ���������������������������������������������������������������������������������������������������������������������������������������������������������������������
(Keep receipt)
Store of Purchase:
�������������������������������������������������������������������������������������������������������������������������������������������������������������������
TECHNICAL SPECIFICATIONS
Voltage: 120V 60Hz
Watts: 1500W
Benefits of registering your product and creating an account:
• Get easier, faster product support and access to warranty
information
• Access troubleshooting and product care instructions
• Be among the first to know about exclusive product promotions
TIP: You can find the model and serial numbers on the QR code label
on the bottom of the unit.
BATTERY REMOVAL AND DISPOSAL
This product’s remote control uses a lithium button battery. When the
battery no longer has a charge, it should be removed from the remote and
recycled. DO NOT incinerate or compost the battery.
When your lithium battery needs to be replaced, dispose of it or recycle it in
accordance with local ordinances or regulations. In some areas, it is illegal to
place spent lithium batteries in the trash or in a municipal solid waste stream.
Return spent battery to an authorized recycling center or to retailer for
recycling. Contact your local recycling center for information on where to drop
o the spentbattery.
FCC WARNINGS
Note: This unit has been tested and found to comply with FCC limits for Class
B digital devices. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This unit generates,
uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications.
To see if this unit interferes with radio or television reception, try turning it
o and on.
To correct any interference:
■Reorient or relocate the receiving antenna.
■Increase the distance between the unit and the receiver.
■Connect the unit to a dierent outlet than the receiver.
■Consult the dealer or an experienced technician for help.
Caution: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate it.
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of your new Shark® Air Purifier.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-800-798-7398
sharkclean.com
Illustrations may dier from actual product. We are constantly striving to improve our products; therefore the specifications contained herein
are subject to change without notice.
This product may be covered by one or more U.S. patents. See sharkninja.com/patents for more information.
© 2023 SharkNinja Operating LLC. SHARK is a registered trademark of SharkNinja Operating LLC.
SHARK NANOSEAL is a trademark of SharkNinja Operating LLC.
HC500�HC450�IB�A4-DIGITAL�REV�Mv2