Shark DE-2010 User manual

MODEL: DE
OPERATING INSTRUCTION
AND PARTS MANUAL
For technical assistance or the SHARK dealer nearest you, call 1-800-771-1881
or visit our website at www.shark-pw.com
■DE-2010 ■DE-2015 ■DE-3010 ■DE-3520
97-710

CONTENTS
2
ModelNumber______________________________
Serial Number ______________________________
Date of Purchase ____________________________
The model and serial numbers will be found on a decal attached to
the pressure washer.You should record both serial number and
date of purchase and keep in a safe place for future reference.
96-720, 97-708, 97-709, 97-710 • REV. 8/04
Important Safety Information................................................................3-4
ComponentIdentification ........................................................................ 5
Assembly Instructions............................................................................. 6
Operating Instructions............................................................................. 7
Applying Detergent and General OperatingTechniques.......................... 8
Shut Down and Clean-Up ....................................................................... 9
Storage ................................................................................................... 9
Troubleshooting .................................................................................... 10
PreventativeMaintenance..................................................................... 11
Oil Change Record ............................................................................... 11
ExplodedView ...................................................................................... 12
ExplodedView Parts List .................................................................13-14
Hose and Spray Gun Assembly ............................................................ 15
PDE4-30025A, B, C ExplodedView...................................................... 16
PDE4-30025A, B, C Parts List .............................................................. 17
Specifications ....................................................................................... 18
Warranty

96-720, 97-708, 97-709, 97-710 • REV. 8/04 3
PRESSURE WASHER OPERATOR’S MANUAL
INTRODUCTION
Thank you for purchasing this Pressure Washer.
All information in this manual is based on the latest
product information available at the time of printing.
Manufacturer reserve the rightto makechangesat any
time without incurring any obligation.
Owner/User Responsibility:
Theownerand/or user must haveanunderstandingof
themanufacturer’s operatinginstructionsandwarnings
before using this pressure washer. Warning informa-
tion should be emphasized and understood.If the op-
erator is not fluent in English, the manufacturer’s in-
structionsandwarnings shall bereadtoanddiscussed
with the operator in the operator’s native language by
the purchaser/owner, making sure that the operator
comprehends its contents.
Owner and/or user must study and maintain for future
reference the manufacturers’instructions.
This manual should be considered a permanent
part of the machine and should remain with it if
machine is resold.
When ordering parts,please specify model and
serial number.
IMPORTANT SAFETY
INFORMATION
CAUTION:To reduce the risk of
injury, read operating instruc-
tions carefully before using.
1. Read the owner's manual
thoroughly. Failure to follow
instructions could cause mal-
function of the machine and
resultindeath,serious bodily
injury and/or property dam-
age.
2. Allinstallationsmustcomply with localcodes.Con-
tact your electrician, plumber, utility company or
the selling distributor for specific details.To com-
ply with the National Electrical Code (NFPA 70)
andprovideadditionalprotectionfromrisk of elec-
tric shock, single phase pressure washers are
equipped with a UL approved ground fault circuit
interrupter (GFCI) power cord. Three phase ma-
chinesmust beconnectedtoaGFCIcircuitbreaker.
WARNING
HIGH PRESSURE
SPRAY CAN PIERCE
SKIN ANDTISSUES.
WARNING: Flammable liquids
can create fumes which can ig-
nite causing property damage
or severe injury.
WARNING: Risk of explosion —
Do not spray flammable liquids.
3. Do not operate in an area
whereflammableorexplosive
materials are used or stored.
WARNING: Keep water spray
away from electrical wiring or
fatal electric shock may result.
4. To protect the operator from
electrical shock,the machine
mustbeelectricallygrounded.
It is the responsibility of the
owner to connect this ma-
chine to a UL grounded re-
ceptacle of proper voltage and amperage ratings.
Do not spray water on or near electrical compo-
nents.
Do not touch machine with wet hands or while
standinginwater.Alwaysdisconnectpowerbefore
servicing.
5. Grip cleaning wand securely with both hands be-
fore starting the cleaner. Failure to do this could
result in injury from a whipping wand.
WARNING: High pressure
stream of fluid that this equip-
ment can produce can pierce
skin and its underlying tissues,
leading to serious injury and
possible amputation.
6. High pressure developed by
these machines will cause
personal injury or equipment
damage. Use caution when operating. Do not di-
rect discharge stream at people, or severe injury
or death will result.
7. Never make adjustments on machine while in
operation.
WARNING:Highpressurespray
can cause paint chips or other
particles to become airborne
and fly at high speeds.
8. Eyesafetydevices,foot,hand
and other protective clothing
mustbe wornwhen usingthis
equipment.
9. Donotoperatewiththespray
gun trigger in the off position for extensive periods
of time as this may cause damage to the pump.
10. The best insurance against an accident is precau-
tion and knowledge of the machine.
READ OPERATOR’S
MANUALTHOROUGHLY
PRIORTO USE.
CAUTION
WARNING
RISK OF EXPLOSION:
DO NOT SPRAY
FLAMMABLELIQUIDS.
WARNING
KEEP WATER SPRAY
AWAY FROM
ELECTRICALWIRING.
WARNING
PROTECTIVE
EYEWEAR AND
CLOTHING MUST BE
WORN.

96-720, 97-708, 97-709, 97-710 • REV. 8/04
OPERATOR’S MANUAL
PRESSURE WASHER
4
11. Manufacturer will not be liable for any changes
made to our standard machines, or any compo-
nents not purchased from us.
12. Becertainallquickcouplerfittingsaresecured be-
fore using pressure washer.
13. Never run pump dry or leave spray gun closed
longer than 5 minutes.
14. Inlet water supply must be cold and clean fresh
water.
15. Do not allow children to operate the pressure
washer at any time.
16. Protect from freezing.
17. When themachineis working,donotcoverorplace
in a closed space where ventilation is insufficient.

96-720, 97-708, 97-709, 97-710 • REV. 8/04 5
PRESSURE WASHER OPERATOR’S MANUAL
COMPONENT IDENTIFICATION
Pump — Develops high pressure.
Spray Gun — Controls the application of water and
detergentontocleaningsurface withtrigger device.In-
cludes safety latch.
Detergent Injector — Allows you to siphon and mix
detergents when used with a soap nozzle.
Wand — Must be connected to the spray gun.
Unloader —Safety devicethat relieves pressure when
spray gun trigger is closed.
High Pressure Hose — Connect one end to water
pumpdischargenippleandtheotherendtospray gun.
Pump Protector — Cycles fresh cool water through
pump when recirculating water reaches 140°F.
GFCI —Groundfaultcircuit interrupter tripswhen volt-
age leaks to ground.
Note:If trigger on spray gun is released for more
than 2 minutes, water will leak from valve. Warm
water will discharge from pump protector onto
floor.This system prevents internal pump damage.
Spray Gun
and Wand
High Pressure
Hose
Pump
Pressure
Nozzle
Garden Hose
(not included)
Unloader
Detergent
Bucket (not
included)
Water Supply
(not included)
Wand
Hanger
Quick
Coupler On/Off
Switch
GFCI
Pump
Protector
Soap
Nozzle
Safety
Latch

96-720, 97-708, 97-709, 97-710 • REV. 8/04
OPERATOR’S MANUAL
PRESSURE WASHER
6
STEP 1: Attach the handle to the
frame of the pressure washer.
Note:Itmaybenecessaryto move
the handle supports from side to
side in order to align the handle so
itwillslideoverthe framesupports.
STEP 2: Insert the carriage bolt
throughtheholesfrom theoutside
of the unit and attach a nut from
theinsideofthe machine.Tighten
nuts.
STEP 3: Attachthespray gun/hose
storage handle, and bracket to
handle.Tighten nuts.
STEP 4: Attach the high pressure
hose to the spray gun using teflon
tape on hose threads.
STEP 7: Release the coupler col-
lar and push the nozzle until the
collar clicks. Pull the nozzle to
make sure it is seated properly.
STEP8:Connect thehighpressure
hose to the pump discharge fitting.
Push coupler collar forward until
secure.
STEP 5: Attach nozzle extension
to spray gun/wand. Tighten both
by hand.
STEP 6: Pullthespring-loadedcol-
lar of the wand coupler back to in-
sertyourchoiceofpressurenozzle.
STEP 9: Connect garden hose to
the cold water source.
ASSEMBLY INSTRUCTIONS
STEP 10: Connect the garden hose to
pump water inlet. Inspect inlets.
CAUTION: Do not run the pump with-
out water or pump damage will result.
Alignment
Holes
Handle
Frame
Assy.
Carriage
Bolt
Nut
Studs
Nut
Hose/Gun
Storage
Bracket
Safety
Latch
Spray
Gun
High Pressure
Hose
Nozzle
Extension
Spray
Gun/Wand Wand
Coupler
Pressure
Nozzle
Pressure
Nozzle Wand
Coupler
Wand
Collar
Pump Discharge
Fitting
High
Pressure
Hose
Cold
Water
Source
Garden
Hose
Pump
Water Inlet Garden
Hose
Coupler Collar
Bolts

96-720, 97-708, 97-709, 97-710 • REV. 8/04 7
PRESSURE WASHER OPERATOR’S MANUAL
OPERATING INSTRUCTIONS
STEP1: Connectgardenhose tothe
coldwatersourceandturn wateron
completely.Never use hot water.
STEP 2:Trigger the spray gun to
eliminate trapped air then wait
for a steady flow of water to
emerge from the spray nozzle.
Cold
Water
Source
Garden
Hose
WARNING! Never replace
nozzles without engaging the
safetylatch onthe sprayguntrig-
ger.
Safety
Latch
STEP 4: Connect to appropriate
power supply. Push reset button on
GFCI.
STEP 4: Turn machine on by turn-
ing switch at top of motor.
On/Off
Switch
The five color-coded quick connect nozzles provide a wide array of spray
widths from 0° to 45° and are easily accessible when placed in the conve-
nient rubber nozzle holder, which is provided on the front of the machine.
NOTE: For a more gentle rinse, select the white 40° or green 25° nozzle.
To scour the surface,selectthe yellow 15° or red 0° nozzle.To apply deter-
gent select the black nozzle.
NOZZLES
WARNING DANGER
7EASYSTEPS
TOOPERATEUNIT
3. CONNECTGARDENHOSE
ANDHIGHPRESSUREHOSE.
TURNWATERSUPPLYON.
4. TRIGGERSPRAY
GUNTORELIEVE
AIR FROMHOSES.
6. WHENJOBIS
COMPLETED,TURN
ENGINESWITCHTOOFF.
7. TRIGGE
RS
TOREL
IEV
FRO
MH
2. INSTALLHIGH
PRESSURE
NOZZLEINWAND.
READ
OWNER’S MANUAL
BEFOREUSING!
1.CHECKENGINE
OILANDGAS
LEVELS.
Nozzle
Coupler
Collar
Wand
CHAUD!
OILALERT
WHENOILLEVELLOW,
ENGINESTOPSIMMEDIATELY.
READOWNER’SMANUALBEFOREOPERATION.
LIRELEMANUELD’UTILISATEURAVANTUSAGE.
VORINBETRIEBNAHMEUNBEDINGT
BEDIENUNGSANLEITUNGDURSCHLESEN.
NOUTILIZARSINANTESNOHABERLEIDOELMANUAL.
Oil
Gas
Garden
Hose
Water
Supply
High
Pressure
Hose
5.OPENFUELVALVE,SET
CHOKE, TURNENGINESWITCH
TO"ON",STARTENGINE.
READOWNER’SMANUALBEFOREOPERATION.
LIRELEMANUELD’UTILISATEURAVANTUSAGE.
VORINBETRIEBNAHMEUNBEDINGT
BEDIENUNGSANLEITUNGDURSCHLESEN.
NOUTILIZARSINANTESNOHABERLEIDOELMANUAL.
CHAUD!
Pull
Start
Choke
Fuel
Valve
Engine
Switch
OILALERT
WHENOILLEVELLOW,
ENGINESTOPSIMMEDIATELY.
READOWNER’SMANUALBEFOREOPERATION.
LIRELEMANUELD’UTILISATEURAVANTUSAGE.
VORINBETRIEBNAHMEUNBEDINGT
BEDIENUNGSANLEITUNGDURSCHLESEN.
NOUTILIZARSINANTESNOHABERLEIDOELMANUAL.
Engine
Switch
RED0¡
YELLOW 15¡ GREEN 25¡ WHITE 40¡ BLACK
(SOAP)

96-720, 97-708, 97-709, 97-710 • REV. 8/04
OPERATOR’S MANUAL
PRESSURE WASHER
8
WARNING:Somedetergentsmay
be harmful if inhaled or in-
gested,causingseverenausea,
faintingorpoisoning.Theharm-
ful elements may cause prop-
erty damage or severe injury.
STEP1:Connect detergentinjectortodischargenipple
on machine. Connect high pressure hose to injector
with quick coupler. (Check to make sure locking cou-
plersleevesareinproperpositionbeforeapplyingwater
pressure).
STEP 2: Use detergent designed
specificallyforpressurewashers.
Householddetergentscould dam-
age the pump.Prepare detergent
solutionas required bythe manu-
facturer. Fill acontainerwithpres-
sure washer detergent.Place the
filterendofdetergent suction tube
into the detergent container.
STEP3:Withsafetylatchon spray
gun engaged, secure black deter-
gent nozzle into quick coupler.
NOTE: Detergent cannot be ap-
plied using a pressure nozzle.
STEP 4:Withthemotorrunning,pulltrigger to operate
machine. Liquid detergent is drawn into the machine
andmixedwithwater.Applydetergent to workarea.Do
notallow detergent to dry on surface.
IMPORTANT:You mustflushthe detergentinjection
system after each use by placing the suction tube
into a bucket of clean water, then run the pressure
washer in low pressure for 1-2 minutes.
THERMALPUMPPROTECTION
If you run the motor on your pressure washer for 3-5
minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach high tempera-
tures. When the water reaches this temperature, the
pump protector engages and cools the pump by dis-
chargingthewarm waterontotheground.Thisthermal
device prevents internal damage to the pump.
CLEANINGTIPS
Pre-rinse cleaning surface with fresh water.Place deter-
gentsuctiontubedirectlyintocleaningsolutionandapply
tosurfaceatlowpressure(forbestresults,limityourwork
areatosectionsapproximately6 feetsquareand always
apply detergent from bottom to top). Allow detergent to
remainon surface1-3minutes.Donotallowdetergentto
dry on surface. If surface appears to be drying, simply
wet down surface with fresh water.If needed, use brush
to remove stubborn dirt.Rinse at high pressure from top
tobottominaneven sweepingmotionkeepingthespray
nozzle approximately 1 foot from cleaning surface. Use
overlapping strokes as you clean and rinse any surface.
For best surface cleaning action spray at a slight angle.
Recommendations:
• Beforecleaninganysurface,an inconspicuousarea
should be cleaned to test spray pattern and dis-
tance for maximum cleaning results.
• Ifpaintedsurfaces are peeling or chipping,useex-
tremecautionaspressurewashermay removethe
loose paint from the surface.
• Keep the spraynozzleasafe distance from the sur-
face you plan to clean.High pressure wash a small
area, then check the surface for damage.If no dam-
age is found, continue to pressure washing.
CAUTION - Never use:
• Bleach, chlorine products and other corrosive
chemicals
• Liquids containing solvents (i.e., paint thinners,
gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the machine and will dam-
age the surface being cleaned.
RINSING
• It will take a few seconds for the detergent to clear.
Applysafety latchtospray gun.Remove blacksoap
nozzle from the quick coupler. Select and install
the desired high pressure nozzle.NOTE: You can
also stop detergent from flowing by simply remov-
ing detergent siphon tube from bottle.
WARNING
DETERGENTS AND GENERAL OPERATINGTECHNIQUES
Detergent
Injector
Soap Nozzle
Quick
Coupler
Filter
Discharge
Nipple

96-720, 97-708, 97-709, 97-710 • REV. 8/04 9
PRESSURE WASHER OPERATOR’S MANUAL
SHUTTING DOWN AND CLEAN-UP
STEP 1: Remove deter-
gent suction tube from
container and insert into
one gallon of fresh water.
Slide nozzle forward for
lowpressure or use black
detergentnozzle.Pulltrig-
ger on spray gun and si-
phonfreshclean waterfor
one minute.
STEP 2: Turnoffmachine
by turning switch to “OFF”
switch.
STEP 5: Disconnect the
garden hose from the wa-
ter inlet on the machine.
STEP 6: Disconnect the
high pressure hose from
high pressure outlet.
STEP 7: Engage the
spray gun safety lock.
STEP4:Presstriggertore-
lease water pressure.
Pump
Water
Inlet High Pressure Outlet Safety
Latch
STORAGE
CAUTION
Pump Storage
CAUTION: Always store your pres-
sure washer in a location where the
temperature will not fall below 32°F
(0°C).The pump in this machine is
susceptible to permanent damage if
frozen.
FREEZE DAMAGE IS NOT COVERED BY WAR-
RANTY.
If you must store your pressure washer in a location
wherethetemperatureisbelow32°F,youcan minimize
thechanceofdamagetoyourmachinebydraining your
machine as follows:
1. Stop the pressure washer and detach supply hose
and high pressure hose. Squeeze trigger of spray
gun to drain all water from the wand and hose.
2. Restartpressure washerandletit runbriefly(about
5 seconds) until water no longer discharges from
the high pressure outlet.
STEP 3: Turn off water
supply.
On/Off
Switch

96-720, 97-708, 97-709, 97-710 • REV. 8/04
PRESSURE WASHER Troubleshooting Guide
10
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
PUMP RUNNING
NORMALLY BUT
PRESSURE LOW ON
INSTALLATION
Pump sucking air Check water supply and possibility of air seepage.
Check valves sticking Check and clean or replace if necessary.
Unloader valve seat faulty Check and replace if necessary.
Nozzle incorrectly sized Check and replace if necessary.
Worn piston packing Check and replace if necessary.
FLUCTUATING PRESSURE Valves worn Check and replace if necessary.
Blockage in valve Check and replace if necessary.
Pump sucking air Check water supply connections.
Worn piston packing Check and replace if necessary.
Insufficient water Check filter and hose for breakage.
PRESSURE LOW AFTER
PERIOD OF NORMAL USE Nozzle worn Check and replace if necessary.
Suction or delivery valves worn Check and replace if necessary.
Suction or delivery lines blocked Check and clean if necessary.
Unloader valve seat worn Check and replace if necessary.
Worn piston packing Check and replace if necessary.
Water temperature excessive Reduce to below 160o F.
PUMP NOISY Air in suction line Check water supply and connections on suction line.
Broken or weak suction or delivery
valve spring Check and replace if necessary.
Foreign matter in valves Check and clean if necessary.
Worn bearings Check and replace if necessary.
Excessive temperature of water Reduce to below 160o F.
PRESENCE OF WATER IN
PUMP OIL Oil seal worn Check and replace if necessary.
High humidity in air Check and replace if necessary.
Piston packing worn Check and replace if necessary.
WATER DRIPPING FROM
UNDER PUMP Piston packing worn Check and replace if necessary.
O-ring plunger retainer worn Check and replace if necessary.
WATER DRIPPING FROM
PUMP PROTECTOR Water supply pressure too high (over
90 PSI) Lower water supply pressure using a regulator.
Spray gun is in the off position for over
5 minutes Turn machine off if not in use for over 5 minutes.
OIL DRIPPING Oil seal worn Check and replace if necessary.
EXCESSIVE VIBRATION IN
HIGH PRESSURE HOSE Irregular functioning of the pump
valves Check and replace if necessary.
MOTOR DOES NOT START
WHEN SWITCHED ON Plug not well connected or lack of
power supply Check plug, cable and switch.
WHEN SWITCHING ON THE
MACHINE, MOTOR HUMS
BUT DOES NOT RUN
Main voltage is insufficient, lower than
the minimum required Check to make sure main power supply is adequate.
The pump is stuck or frozen Check by turning the motor manually.
MOTOR STOPS Tripped thermal overload due to
overheating Check that main voltage corresponds to the specifications. Wait a few minutes before turning on
the machine again by resetting the GFCI cord.

96-720, 97-708, 97-709, 97-710 • REV. 8/04 11
PRESSURE WASHER Troubleshooting Guide
PREVENTATIVE MAINTENANCE
This pressure washer was produced with the best available materials and quality craftsmanship.However, you
as the owner have certain responsibilities for the correct care of the equipment.Attention to regular preventa-
tive maintenance procedures will assist in preserving the performance of your equipment.Contact your dealer
for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer.
Performmaintenancemoreoftenundersevereconditions.
OIL CHANGE RECORD
Check pump oil and engine oil level before first use of your new pressure washer.
Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
MAINTENANCE SCHEDULE
Pump Oil Inspect Daily inspect the oil level
Change After first 50 hours, then every 500 hours or annually
Replace High Pressure Nozzle Every 6 months
Replace Quick Connects Annually
Clean Water Screen/Filter Weekly
Replace HP Hose Annually if there is any sign of wear
Grease Motor Every 10,000 hours
PREVENTATIVE MAINTENANCE

96-720, 97-708, 97-709, 97-710 • REV. 8/04
OPERATOR’S MANUAL
PRESSURE WASHER
12
EXPLODED VIEW
1
3
2
19 18
17 16 15
14
65
25
24
23 26
27
10
9
11
10
32
39
38
37
35
36
8
8
39
39 33
28
29
31
30
42
44
49
53 50
51
52
48
49
48 47
45
46
44
43
59
58
53
56
57
54
31
68
50
52
62
22
21
32
20 61
21
60
63
5
6, 7
5
15 16
17
22
21
21
(Models 352009A)
(Model 4-20021A,
352007A)
25
23
24
26
27
13
12
4
66, 67
66, 67
10
10
70
15 16 17
14, 65
34
1
65, 14
48
55
4155
41
201007D,
201009D,
2-11021D
201507D
2-15021D
301007D
301009D
301509D
40
40
68
70
40

96-720, 97-708, 97-709, 97-710 • REV. 8/04 13
PRESSURE WASHER OPERATOR’S MANUAL
EXPLODED VIEW PARTS LIST
ITEM PART NO. DESCRIPTION QTY
1 See Specifications Page 18, For Nozzle Size
4-12803015 Nozzle, 1503, Yellow 1
4-12803025 Nozzle, 2503, Green 1
4-12803040 Nozzle, 4003, White 1
4-12803000 Nozzle, 0003, Red 1
4-12804015 Nozzle, 1504, Yellow 1
4-12804025 Nozzle, 2504, Green 1
4-12804040 Nozzle, 4004, White 1
4-12804000 Nozzle, 0004, Red 1
4-12805015 Nozzle, 1505, Yellow 1
4-12805025 Nozzle, 2505, Green 1
4-12805040 Nozzle, 4005, White 1
4-12805000 Nozzle, 0005, Red 1
4-12805515 Nozzle, 1555, Yellow 1
4-12805525 Nozzle, 2555, Green 1
4-12805540 Nozzle, 4055, White 1
4-12805500 Nozzle, 0055, Red 1
4-12806015 Nozzle, 1506, Yellow 1
4-12805025 Nozzle, 2506, Green 1
4-12806040 Nozzle, 4006, White 1
4-12806000 Nozzle, 0006, Red 1
4-16540 Nozzle, Compl. QCME 6540,
Brass, All 1
2 4-011106 Wand, 18" M22 x 1/4" QC 1
3 4-011137 Spray Gun, SK@, 3/8" Inlet,
Lance w/M22 Coupler 1
4 Hose, See Specifications Page 18
5 6-051591 Connector, 1/2" L/T, 90°,
Black (201507D, 2-15021D,
301007D, 301009D, 301509A)2
6 6-0104 Cord, Service, SOWA 12/3,
Coleman (201507D,
2-15021D, 301007D, 301009D,
301509A) 21 in.
7 6-0128 Conduit, Watertight, Flex,
1/2 (201507D, 2-15021D,
301007D, 301009D,
301509A) 8 in.
8 90-2000 Nut, 1/4" ESNA, NC 6
9 4-011184 Injector, Det., Assy, 3-5 GPM 1
10 6-051593 Connector, 3/4" L/T, 90°,
Black (352007A, 352009A,
4-20021A) 2
11 5-18031 Plate, Pump Mount, Hawk
(352009A) 1
90-10302 Bolt,
6mm x 25mm/6mm x3mm
(352009A) 4
90-50094 Key, Step,
8mm x 6mm/6mm x3mm
(352009A) 1
12 90-40091 Washer, 1/2" Lock (352009A)4
13 90-10271 Bolt, 1/2" x 1" Hex, NC HH
(352009A) 4
ITEM PART NO. DESCRIPTION QTY
14 90-1991 Screw, 10/32" x 1/2" BHSOC
Black (201507D, 2-15021D,
301007D, 301009D, 301509A,
352007A, 352009A,
4-20021A) 4
15 6-020204 Switch, 2 Pos. 120V-600V,
1-3 PH Bremas (201507D,
2-15021D, 301007D, 301009D,
301509A, 352007A, 352009A,
4-20021A) 1
16 6-03911 Lid, Plastic, Carlon E9801
Box (201507D, 2-15021D,
301007D, 301009D, 301509A,
352007A, 352009A,
4-20021A) 1
17 6-03910 Box, Plastic, Carlon E9801,
w/o Lid (201507D, 2-15021D,
301007D, 301009D, 301509A,
352007A, 352009A,
4-20021A) 1
18 90-19713 Screw, 5/16" x 3/4" Whiz
(352009A) 2
90-20012 ▲Nut, 5/16" Flange, Whiz
(352009A) 2
19 95-07500186 Bracket, Switch Box
(352009A) 1
20 6-010631 GFCI, 240V 1Ph 20A, 36'
12-3 Cord (301509A) 1
6-01059 GFCI, 240V 1Ph 30A, 36' 10-3
Cord (352007A, 352009A,
4-20021A) 1
6-01060 GFCI, 120V 20A, w/36' 12-3
Cord (301009D, 301007D,
201507D, 2-15021D) 1
6-01062 GFCI, 120V 15A, w/36'
12-3 Cord (201009D,
201007D, 2-11021D) 1
21 10-08021 Label, Disconnect Power
Supply 1
22 95-07105000 Cover, Motor (201507D,
2-15021D, 301007D, 301009D,
301509A, 4-20021A,
3-52007A) 1
23 2-2006 Nipple, 3/8" x 3/8" NPT, ST
Female 1
24 2-10943 Swivel, 3/8" MP x 3/4" GHF
w/Strainer (PDE, EP) 1
2-10942 Swivel, 1/2" MP x 3/4" GHF,
w/Strainer (DE, DL) 1
25 2-300816 Protector, Pump, 3/8" PTP
(EP, PDE) 1
2-30082 Protector, Pump, 1/2" PTP
(DL, DE) 1
26 Unloader, See Specifications Page 18
27 Pump, See Specifications Page 18

96-720, 97-708, 97-709, 97-710 • REV. 8/04
OPERATOR’S MANUAL
PRESSURE WASHER
14
ITEM PART NO. DESCRIPTION QTY
28 90-1016 Bolt, 3/8" x 1" NC
(All except 352009A) 4
29 90-4002 Washer, 3/8" SAE, Flat
(All except 352009A) 4
30 90-1006 Bolt, 5/16" x 3/4" NC
(All except 352009A) 4
90-1016 Bolt, 3/8" x 1" NC HH
(352009A) 4
31 90-4001 Washer, 5/16" Flat
(All except 352009A) 8
90-4002 Washer, 3/8" SAE, Flat
352009A) 8
32 Motor, See Specifications Page 18
33 2-0103 Grommet, Rubber, Nozzle
Holder 5
34 90-20012 Nut, 5/16" Flange, Whiz
Loc 4
35 95-07104921 Handle, Grab, Red
(DE, DL, EP) 1
95-07104961 Handle, Grab, Chrome (PDE)1
36 11-0362 Label (EP Models) 1
11-08022 Label (PDE Models) 1
11-0361 Label (DE Models) 1
11-0363 Label (DL Models) 1
37 95-07104945 Plate, Warning/Instr. Red
(EP, DE, DL) 1
95-07104966 Plate, Warning/Instr. Blk
(PDE) 1
38 95-07102382 Hanger, Hose/Wand, 1
39 90-100473 Bolt, Carriage, 1/4"-20 x
1-3/4" 6
40 90-4000 Washer, 1/4" Flat 6
41 90-2001 Nut, 5/16" ESNA, NC 4
42 95-07104920 Handle, Lower Grab, Red
(DE, DL, EP) 1
95-07104950 Handle, Lower Grab, Black
(PDE) 1
43 95-07104923 Retainer Bracket, Handle,
Red (DE, DL, EP) 2
95-07104924 Retainer Bracket, Handle,
Black (PDE) 2
44 90-1020 Bolt, 3/8" x 2" 4
45 90-10201 Bolt, 3/8" x 2-1/4" 2
46 90-40125 Washer, 3/8" x 1" 2
47 2-01041 Pad, Soft Rubber, 50 Duro 2
48 90-4002 Washer, 3/8" SAE, Flat 6
49 90-2002 Nut, 3/8" ESNA, NC 6
50 90-200422 Cap, 5/8" Axle Hub, Black 2
51 4-0303 Wheel & Tire Assy., 4" Steel
Rim w/Tube 2
52 2-01403 Bushing, Snap, 5/8" 2
53 90-10077 Belt, Carriage 5/16" x 1-3/4" 4
54 95-07102313 Axle, 5/8" x 19.625" Long 1
ITEM PART NO. DESCRIPTION QTY
55 90-4001 Washer, 5/16" Flat, SAE 4
56 95-07104922 Handle, Bumper, Red (EP, DL
DE Models) 1
95-07104962 Handle, Bumper, Chrome (PDE
Models) 1
57 95-07104927 Base, CW Direct, Red (EP, DL
DE Models) 1
95-07104965 Base, CW Direct, Black
(PDE Models) 1
58 10-08017 Label, Intended For Outdoor
Use 1
59 10-9999 Label, Clear Lexan, 2-1/4” x
4-1/2" 1
60 6-02049 Switch Assembly (201007D,
201009D, 2-11021D) 1
61 10-08018 Label, Warning, Service
Cord 1
62 6-05154 Strain Relief, Flex 90°, Plastic
(201507D, 2-15021D, 301007D,
301009D, 301509A) 1
63 6-05152 Strain Relief (201007D,
201009D, 2-11021D) 1
6-05181A ▲ Locknut, 1/2" (201007D,
201009D, 2-11021D) 1
64 90-017 ▲Nut, 10/32" Keps 3
90-100030 ▲ Screw, 10/32" x 3/4" Slot Pan,
MS, SS 1
11-1042 ▲Label, Ground 1
65 90-017 Nut, 10/32" Keps (201507D,
2-15021D, 301007D, 301009D,
301509A, 352007A, 352009A,
4-20021A) 4
66 6-01280 Conduit, Water Tite, Flex 3/4"
(352009A) 21 in.
(4-20021A, 352007A) 18 in.
67 6-0108 Cord, Service, 10/3
(352009A) 34 in.
(4-20021A, 352007A) 31 in.
68 90-2001 Nut, 5/16" ESNA
(All except 352009A) 4
90-2002 Nut, 3/8" ESNA (352009A) 4
69 2-1044 ▲Plug, 1/8" Countersunk
(2-11021D, 2-15021D,
4-20021A) 1
2-1046 ▲Plug, 1/4" Countersunk
(201007D, 201507D, 301007D,
352007A) 4
70 6-051595 Strain Relief 3/4" 1
6-05172 ▲Locknut, 3/4" (352007A,
352009A, 4-20021A) 1
▲ Not Shown

96-720, 97-708, 97-709, 97-710 • REV. 8/04 15
PRESSURE WASHER OPERATOR’S MANUAL
HOSE AND SPRAY GUN ASSEMBLY
HOSE AND SPRAY GUN ASSEMBLY PARTS LIST
ITEM PART NO. DESCRIPTION QTY
1 2-2002 Coupler, 3/8" Female 1
2-0121 ▲Quick Coupler O-Ring 1
2 4-0203050C Hose, 50' x 3/8" w/Coupler
(EP, PDE, DL Models) 1
4-02093450BC Hose, 50’ x 3/8” w/Coupler
(DE Models) 1
3 4-011137 Spray Gun, Shut-Off 1
4 4-011106 Wand, Straight 1
5 2-2000 Coupler, 1/4" Female 1
2-0119 Quick Coupler O-Ring 1
6 Nozzle, See Page 18 For Size
ITEM PART NO. DESCRIPTION QTY
7 4-16540 Nozzle, Brass Soap 1
8 3-12021 Injector, Det., Non-Adjust,
3-5GPM, .083 1
9 2-9040 Clamp, Hose, .46 - .54 ST 2
10 4-02080000 Tube, 1/2" x 1/2" Clear Vinyl 6 ft.
11 2-1904 Strainer, 1/4" Hose Barb,
Plastic 1
▲Not Shown
6
2
3
7
5
1
4
10
8
9
11
9

96-720, 97-708, 97-709, 97-710 • REV. 8/04
OPERATOR’S MANUAL
PRESSURE WASHER
16
29
PDE4-30025A, B, C EXPLODED VIEW
3
43
25
27 26
6
23
45
9
41
7
19
31
46
24
30
8
33
32
16
16
32
30
48
37
29
13
30
36
21
18
12
35
10
4
2
14 22
20
32
28
15 5
42
17
44
49
40
32
28
32 30
51
50
3
1
52
39
38

96-720, 97-708, 97-709, 97-710 • REV. 8/04 17
PRESSURE WASHER OPERATOR’S MANUAL
ITEM PART NO. DESCRIPTION QTY
1 95-07104924 Retainer, Bracket 2
2 2-1902 Strainer, Inlet Garden Hose 1
3 6-010690 Cord w/GFCI, 240V, 30 Amp
TRC (4-3000A) 1
6-0109 Cord, Service, SEO 10/4
(4-3000B) 15 ft.
6-0105 Cord, Service 12/4
(4-3000C) 15 ft.
4 95-07104962 Handle, Bumper, Chrome 1
5 2-10942 Swivel, 1/2" MP x 3/4" GHF
W/Strainer 1
6 6-5012 Overload, 18.00 - 24 Amp
(4-3000B) 1
6-5009 Overload, 7.50 - 11 Amp
(4-3000C) 1
7 10-08018 Label, Warning, Service
Cord 1
8 95-07104961 Handle, Grab, Chrome 1
9 6-021595 Din Rail, 35mm 4"
10 95-07104950 Handle, Lower Grab,
Chrome 1
11 90-017 ▲Nut, 10/32" KEPS 6
90-1994 ▲Screw, 10/32" XD 1-1/4" 1
90-1991 ▲Screw, 10/32" x 1/2",
BHSOC B1 7
12 2-0103 Grommet, 1/8" Rubber 2
13 2-01041 Pad, Soft Rubber, 50 Duro 2
14 2-2006 Nipple, 3/8" x 3/8" NPT ST
Female 1
15 2-30082 Pump Protector, 1/2" PTP 1
16 4-0303 Wheel, 4" Steel Rim 2
17 4-12804015 Nozzle, SAQCMEG 1504,
Yellow (4-3000) 1
18 4-16540 Nozzle Compl, QCEM-6540
w/Black Nylon 1
19 5-10130 Motor 7.5 HP 1 PH C-Face
1725RPM, 37N07X177
(4-30025A) 1
5-10143 Motor 7.5 HP 3 PH C-Face
1725 RPM, 37B12X54G1
(4-30025B, C) 1
6-05171 ▲Strain Relief, 1"
(4-3000B/C) 1
20 5-2263 Pump, AR
RKA35G30E-F17 1
21 10-08028 Tag, Remove Pump Plug 1
22 5-3203 Unloader, AR-20242G, 3-4
GPM/3500 PSI, Black Knob 1
23 6-2021 Switch, GRN PB, CH 1
24 6-2022 Switch, Red PB, CH 1
ITEM PART NO. DESCRIPTION QTY
25 6-03904 Enclosure, Fiberglass,
NEMA4X 1
11-1042 ▲Label, Ground 1
26 10-08015A Label, PE Off/On, For Push
Buttons 1
27 10-08021 Label, Disconnect Power
Supply 1
28 90-1016 Bolt, 3/8" x 1", NC HH 8
29 90-1020 Bolt, 3/8" x 2", NC HH 4
30 90-2002 Nut, 3/8", ESNA, NC 18
31 6-2000 Block, Contact, N/C 1
32 90-4002 Washer, 3/8", SAE, Flat 14
33 90-200422 Cap, 5/8 Axle Hub, Black 2
34 90-40125 Washer, 3/8" x 1" Steel 2
35 95-07104964 Base 1
36 90-10072 Bolt, 5/16" x 2, NC Carriage 2
37 90-100473 Bolt, Carriage 1/4-20 x 1-3/4
Zinc 4
38 90-10077 Bolt, Carriage 5/16 x 1-3/4 4
39 2-001403 Bushing, Axle, 1/2 x 5/8 x 3/4
Flange 2
40 95-07102313 Axle, 5/8 x 19-5/8 1
41 6-05172 Locknut, 3/4", Conduit 2
42 6-051595 Strain Relief, STRT, LQ Tite 2
6-05170 Strain Relief, 3/4", Water Tite
(4-3000A) 1
43 6-4019 Contactor, 240V, CH,
CE15HNS3BB-09
(4-3000A) 1
6-4011 Contactor, 240V, CH,
CE15FNS3BB (4-3000B) 1
6-4009 Contactor, 480V, CH
CE15DNS3CB (4-3000C) 1
44 11-08022 Label 1
45 95-07101025 Bracket, Electrical Box 1
46 6-2001 Block, Contactor, N/O 1
47 90-102702 Bolt, 1/2" x 1-1/2" NC HH
Zinc 4
48 90-40091 Washer, 1/2" 4
49 45-07104966 Plate, Black 1
50 95-07102382 Hanger, Hose & Wand 1
51 6-0102 Cord, Service, 8/3
(4-3000A) 2.75 ft.
6-0105 Cord, Service, 12/4
(4-3000C) 2.75 ft.
6-0109 Cord, Service 10/4
(4-3000B) 2.75 ft.
52 90-20012 Nut, 5/16" Flange, Whiz Loc 2
▲Not Shown

96-720, 97-708, 97-709, 97-710 • REV. 8/04
PRESSURE WASHER Specifications
18
SPECIFICATIONS
Machine Pessure Nozzle Pump Pump Unloader Motor Motor
Model GPM (PSI) Size Hose p/n Part # Model Part # Hp Part #
EP-201009D 2.0 1000 4.0 4-0203050C 5-1802 HC205AL 5-3303 1-1/2 5-1004M
EP-301009D 3.0 1000 6.0 4-0203050C 5-1806 HC235 5-3303 2 5-1073
EP-301509A 3.0 1500 5.0 4-0203050C 5-1806 HC235 5-3303 3 5-10081
EP-352009A 3.5 2000 5.0 4-0203050C 5-1803 HC450R 5-3303 5 5-10104
PDE2-11021D 2.0 1000 4.0 4-0203050C 5-23001 TT9061EBF 5-3024 1-1/2 5-1046
PDE2-15021D 1.9 1500 3.0 4-0203050C 5-23001 TT9061EBF 5-3024 2 5-1047
PDE4-20021A 3.5 2000 5.0 4-0203050C 5-2303 TT2035EBF 5-3024 5 5-1053
PDE4-30025A 3.5 3000 4.0 4-0203050C 5-2263 RKA35G30E-17 5-3203 7-1/2 5-10130
PDE4-30025B 3.5 3000 4.0 4-0203050C 5-2263 RKA35G30E-17 5-3203 7-1/2 5-10143
PDE4-30025C 3.5 3000 4.0 4-0203050C 5-2263 RKA35G30E-17 5-3203 7-1/2 5-10143
DL-201007D 2.0 1000 4.0 4-0203050C 5-1618 WMH-2521-F 5-3150 1-1/2 5-1046
DL-201507D 1.9 1500 3.0 4-0203050C 5-1618 WMH-2521-F 5-3150 2 5-1047
DL-301007D 2.8 1500 5.5 4-0203050C 5-1620 WMH-1528-F 5-3150 2 5-1047
DL-352007A 3.5 2000 5.0 4-0203050C 5-1621 WMH-2035-F 5-3150 5 5-1053
DE-201007D 2.0 1000 4.0 4-02093450BC 5-1618 WMH-2521-F 5-3150 1-1/2 5-1046
DE-201507D 1.9 1500 3.0 4-02093450BC 5-1618 WMH-2521-F 5-3150 2 5-1047
DE-301007D 2.8 1000 5.5 4-02093450BC 5-1620 WMH-1528-F 5-3150 2 5-1047
DE-352007A 3.5 2000 5.0 4-02093450BC 5-1621 WMH-2035-F 5-3150 5 5-1053

SHARK DE • 97-710 • REV. 8/04
PRESSURE WASHER WARRANTY
SHARK LIMITED NEW PRODUCT WARRANTY
PRESSURE WASHERS
WHAT THIS WARRANTY COVERS
All SHARK PRESSURE WASHERS are warranted by SHARK to the original purchaser to be free from defects in materials
and workmanship under normal use, for the periods specified below. This Limited Warranty is subject to the exclusions shown
below, is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced
under this warranty will assume the remainder of the part’s warranty period. This warranty applies to the original purchaser
and is not transferable.
LIMITED LIFETIME PARTS WARRANTY:
Components manufactured by SHARK, such as frames, handles, and belt guards. Forged brass pump manifold. All heating
coils will have a three year warranty. Internal components (excluding oil seals) on the oil-end of all pressure washer pumps will
have a seven year warranty.
ONE YEAR PARTS WARRANTY:
All other components, excluding normal wear items as described below, will be warranted for one year on parts. Warranty on
these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty.
WARRANTY PROVIDED BY OTHER MANUFACTURERS:
Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manu-
facturers’ local authorized service centers. SHARK cannot provide warranty on these items.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover the following items:
1. Normal wear items, such as nozzles, guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings,
packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protectors.
2. Damage or malfunctions resulting from accidents, abuse, modifications, alterations, incorrect installation, improper
servicing, failure to follow manufacturer’s maintenance instructions, or use of the equipment beyond its stated usage
specifications as contained in the operator’s manual.
3. Damage due to freezing, chemical deterioration, scale buildup, rust, corrosion, or thermal expansion.
4. Damage to components from fluctuations in electrical or water supply.
5. Normal maintenance service, including adjustments, fuel system cleaning, and clearing of obstructions.
6. Transportation to service center, shop labor charges, field labor charges, or freight damage.
WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE
While not required for warranty service, we request that you register your SHARK pressure washer by returning the com-
pleted registration card. In order to obtain warranty service on items, you must return the product to an Authorized SHARK
Dealer, freight prepaid, with proof of purchase, within the applicable warranty period. If the product is permanently installed,
you must notify your Authorized SHARK Dealer of the defect.The Authorized Dealer will file a claim, which must subsequently
verify the defect. In most cases, the part must be returned to SHARK freight prepaid with the claim. For warranty service on
components warranted by other manufacturers, the Authorized Dealer can help you obtain warranty service through these
manufacturers’ local authorized service centers.
LIMITATION OF LIABILITY
SHARK’S liability for special, incidental, or consequential damages is expressly disclaimed. In no event shall SHARK’S
liability exceed the purchase price of the product in question. SHARK makes every effort to ensure that all illustrations and
specifications are correct, however, these do not imply a warranty that the product is merchantable or fit for a particular
purpose, or that the product will actually conform to the illustrations and specifications. THE WARRANTY CONTAINED
HEREIN IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to
make any representation or promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way. It is the
buyer’s responsibility to ensure that the installation and use of SHARK products conforms to local codes. While SHARK
attempts to assure that its products meet national codes, it cannot be responsible for how the customer chooses to use or
install the product.
SHARK PRESSURE WASHERS
1-800-771-1881 • www.shark-pw.com

Form#97-710 • Revised8/04 • Printedin U.S.A.