Shark DE-2010 User manual

MODEL: DE
OPERATING INSTRUCTION
AND PARTS MANUAL
For technical assistance or the SHARK dealer nearest you, call 1-800-771-1881
or visit our website at www.shark-pw.com
■DE-2010 ■DE-2015 ■DE-3010 ■DE-3520
97-710

CONTENTS
2
ModelNumber______________________________
Serial Number ______________________________
Date of Purchase ____________________________
The model and serial numbers will be found on a decal attached to
the pressure washer.You should record both serial number and
date of purchase and keep in a safe place for future reference.
96-720, 97-708, 97-709, 97-710 • REV. 2/04
Important Safety Information................................................................3-4
ComponentIdentification ........................................................................ 5
Assembly Instructions............................................................................. 6
Operating Instructions............................................................................. 7
Applying Detergent and General OperatingTechniques.......................... 8
Shut Down and Clean-Up ....................................................................... 9
Storage ................................................................................................... 9
Troubleshooting .................................................................................... 10
PreventativeMaintenance..................................................................... 11
Oil Change Record ............................................................................... 11
ExplodedView ...................................................................................... 12
ExplodedView Parts List .................................................................13-14
Hose and Spray Gun Assembly ............................................................ 15
PDE4-30025A, B, C ExplodedView...................................................... 16
PDE4-30025A, B, C Parts List .............................................................. 17
Specifications ....................................................................................... 18
Warranty

96-720, 97-708, 97-709, 97-710 • REV. 2/04 3
PRESSURE WASHER OPERATOR’S MANUAL
INTRODUCTION
Thank you for purchasing this Pressure Washer.
Allinformationinthis manualis basedonthelatest prod-
uct information available at the time of printing.
Manufacturer reservethe righttomakechanges atany
time without incurring any obligation.
Owner/User Responsibility:
The owner and/or user must have an understanding of
themanufacturer’s operating instructions and warnings
before using this pressure washer.Warninginformation
should be emphasized and understood.If the operator
is not fluent in English, the manufacturer’s instructions
and warnings shall be read to and discussed with the
operator in the operator’s native language by the pur-
chaser/owner, making sure that the operator compre-
hends its contents.
Owner and/or user must study and maintain for future
reference the manufacturers’instructions.
This manual should be considered a permanent
part of the machine and should remain with it if
machine is resold.
When ordering parts, please specify model and
serial number.
IMPORTANT SAFETY
INFORMATION
CAUTION:To reduce the risk of
injury, read operating instruc-
tions carefully before using.
1. Readtheowner'smanualthor-
oughly. Failure to follow in-
structions could cause mal-
function of the machine and
result in death, serious bodily
injury and/or property dam-
age.
2. Allinstallationsmustcomplywithlocalcodes.Con-
tactyourelectrician,plumber, utility companyorthe
sellingdistributorforspecificdetails.To complywith
the National Electrical Code (NFPA 70) and pro-
videadditionalprotection from riskof electricshock,
single phase pressure washers are equipped with
aULapprovedgroundfaultcircuitinterrupter(GFCI)
power cord. Three phase machines must be con-
nected to a GFCI circuit breaker.
WARNING
HIGH PRESSURE
SPRAY CAN PIERCE
SKIN ANDTISSUES.
WARNING: Flammable liquids
can create fumes which can ig-
nite causing property damage or
severe injury.
WARNING: Risk of explosion —
Do not spray flammable liquids.
3. Risk of explosion — do not
spray flammable liquids or
operate in an area where
flammableorexplosivematerialsareusedorstored.
WARNING: Keep water spray
away from electrical wiring or
fatal electric shock may result.
4. To protect the operator from
electrical shock, the machine
mustbeelectricallygrounded.
It is the responsibility of the
ownertoconnectthismachine
to a UL grounded receptacle
of proper voltage and amperage ratings.
Do not spray water on or near electrical compo-
nents.
Donot touchmachinewithwethands orwhilestand-
ing in water. Always disconnect power before ser-
vicing.
5. Grip cleaning wand securely with both hands be-
fore starting the cleaner. Failure to do this could
result in injury from a whipping wand.
WARNING: High pressure
stream of fluid that this equip-
ment can produce can pierce
skin and its underlying tissues,
leading to serious injury and
possible amputation.
6. High pressure developed by
these machines will cause
personal injury or equipment
damage. Use caution when operating. Do not di-
rectdischargestreamatpeople,orsevereinjury or
death will result.
7. Never make adjustments on machine while in
operation.
WARNING:High pressure spray
can cause paint chips or other
particles to become airborne
and fly at high speeds.
8. Eye safety devices, foot pro-
tectionandprotectiveclothing
must be worn when using this
equipment.
9. Do not operate with the trig-
ger in the off position for extensive periods of time
as this may cause damage to the pump.
10. The best insurance against an accident is precau-
tion and knowledge of the machine.
READ OPERATOR’S
MANUALTHOROUGHLY
PRIORTO USE.
CAUTION
WARNING
RISK OF EXPLOSION:
DO NOT SPRAY
FLAMMABLELIQUIDS.
WARNING
PROTECTIVE
EYEWEAR AND
CLOTHING MUST BE
WORN.
WARNING
KEEP WATER SPRAY
AWAY FROM
ELECTRICALWIRING.

96-720, 97-708, 97-709, 97-710 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
4
11. Manufacturerwill notbeliableforanychanges made
to our standard machines, or any components not
purchased from us.
12. Be certain all quick coupler fittings are secured be-
fore using pressure washer.
13. Never run pump dry or leave spray gun closed
longer than 5 minutes.
14. Inlet water supply must be cold and clean fresh
water.
15. Donotallow childrentooperatethepressurewasher
at any time.
16. Protect from freezing.
17. Whenthemachineis working, donotcoverorplace
in a closed space where ventilation is insufficient.

96-720, 97-708, 97-709, 97-710 • REV. 2/04 5
PRESSURE WASHER OPERATOR’S MANUAL
COMPONENT IDENTIFICATION
Pump — Develops high pressure.
Spray Gun — Controls the application of water and
detergent onto cleaning surface with trigger device.In-
cludes safety latch.
Detergent Injector — Allows you to siphon and mix
detergents.
Wand — Must be connected to the spray gun.
High Pressure Hose — Connect one end to water
pump discharge nipple and the other end to spray gun.
Pump Protector — Cycles fresh cool water through
pump when recirculating water reaches 140°F.
Note:If trigger on spray gun is released for more
than 2 minutes, water will leak from valve. Warm
waterwilldischarge frompump protectorontofloor.
This system prevents internal pump damage.
Spray Gun
and Wand
High Pressure
Hose
Pump
Pressure
Nozzle
Garden Hose
(not included)
Unloader
Detergent
Bucket (not
included)
Water Supply
(not included)
Wand
Hanger
Quick
Coupler On/Off
Switch
GFCI

96-720, 97-708, 97-709, 97-710 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
6
STEP 1: Attach the handle to the
frame of the pressure washer.
Note:Itmaybenecessaryto move
the handle supports from side to
side in order to align the handle so
itwillslideover the framesupports.
STEP2: Insertthecarriage boltthrough
the holes from the outside of the unit
and attach a nut from the inside of the
machine.Tighten nuts.
STEP 3: Attach the spray gun/
hose storage handle, and
bracket to handle.Tighten nuts.
STEP 4: Attach the high
pressure hose to the spray
gun using teflon tape on
hose threads.
STEP 7: Release the coupler col-
lar and push the nozzle until the
collar clicks. Pull the nozzle to
make sure it is seated properly.
STEP 8: Connectthehighpressure
hose to the pump discharge fitting.
Push coupler collar forward until
secure.
STEP 5: Attachnozzleextension to spray
gun/wand. Tighten both by hand. STEP 6: Pullthespring-loadedcol- lar of the wand coupler back to in-
sertyourchoiceofpressurenozzle.
STEP 9: Connect garden hose to
the cold water source.
ASSEMBLY INSTRUCTIONS
STEP 10: Connect the garden hose to pump water inlet.
Inspect inlets. CAUTION: Do not run the pump without
water or pump damage will result.
Alignment
Holes
Handle
Frame
Assy.
Carriage
Bolt
Nut
Studs
Nut
Hose/Gun
Storage
Bracket
Safety
Latch
Spray
Gun
High Pressure
Hose
Nozzle
Extension
Spray Gun/
Wand
Wand
Coupler
Pressure
Nozzle
Pressure
Nozzle Wand
Coupler
Wand
Collar
Pump
Discharge
Fitting
High
Pressure
Hose
Cold
Water
Source
Garden
Hose
Pump
Water Inlet
Garden
Hose
Coupler Collar
Bolts

96-720, 97-708, 97-709, 97-710 • REV. 2/04 7
PRESSURE WASHER OPERATOR’S MANUAL
OPERATING INSTRUCTIONS
STEP1: Connectgardenhose tothe
coldwatersource and turnwateron
completely.Never use hot water.
STEP 2:Trigger the spray gun to
eliminate trapped air then wait for
a steady flow of water to emerge
from the spray nozzle.
Cold
Water
Source
Garden
Hose
WARNING! Never replace
nozzles without engaging the
safety latch on the spray gun trig-
ger.
Safety
Latch
STEP 4: Connect to ap-
propriate power supply.
Push reset button on
GFCI.
STEP 4: Turn machine on by turning
switch at top of motor.
On/Off
Switch
The five color-coded quick connect nozzles provide a wide array of spray
widths from 0° to 45° and are easily accessible when placed in the conve-
nient rubber nozzle holder, which is provided on the front of the machine.
NOTE: For a more gentle rinse, select the white 40° or green 25° nozzle.
To scour the surface,selectthe yellow 15° or red 0° nozzle.Toapplydeter-
gent select the black nozzle.
NOZZLES
WARNING DANGER
7EASYSTEPS
TOOPERATEUNIT
3. CONNECTGARDENHOSE
ANDHIGHPRESSUREHOSE.
TURNWATERSUPPLYON.
4. TRIGGERSPRAY
GUNTORELIEVE
AIR FROMHOSES.
6. WHENJOBIS
COMPLETED,TURN
ENGINESWITCHTOOFF.
7. TRIGGE
RS
TOREL
IEV
FRO
MH
2. INSTALLHIGH
PRESSURE
NOZZLEINWAND.
READ
OWNER’S MANUAL
BEFOREUSING!
1.CHECKENGINE
OILANDGAS
LEVELS.
Nozzle
Coupler
Collar
Wand
CHAUD!
OILALERT
WHENOILLEVELLOW,
ENGINESTOPSIMMEDIATELY.
READOWNER’SMANUALBEFOREOPERATION.
LIRELEMANUELD’UTILISATEURAVANTUSAGE.
VORINBETRIEBNAHMEUNBEDINGT
BEDIENUNGSANLEITUNGDURSCHLESEN.
NOUTILIZARSINANTESNOHABERLEIDOELMANUAL.
Oil
Gas
Garden
Hose
Water
Supply
High
Pressure
Hose
5.OPENFUELVALVE,SET
CHOKE, TURNENGINESWITCH
TO"ON",STARTENGINE.
READOWNER’SMANUALBEFOREOPERATION.
LIRELEMANUELD’UTILISATEURAVANTUSAGE.
VORINBETRIEBNAHMEUNBEDINGT
BEDIENUNGSANLEITUNGDURSCHLESEN.
NOUTILIZARSINANTESNOHABERLEIDOELMANUAL.
CHAUD!
Pull
Start
Choke
Fuel
Valve
Engine
Switch
OILALERT
WHENOILLEVELLOW,
ENGINESTOPSIMMEDIATELY.
READOWNER’SMANUALBEFOREOPERATION.
LIRELEMANUELD’UTILISATEURAVANTUSAGE.
VORINBETRIEBNAHMEUNBEDINGT
BEDIENUNGSANLEITUNGDURSCHLESEN.
NOUTILIZARSINANTESNOHABERLEIDOELMANUAL.
Engine
Switch
RED0¡
YELLOW 15¡ GREEN 25¡ WHITE 40¡ BLACK
(SOAP)

96-720, 97-708, 97-709, 97-710 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
8
WARNING: Some detergents
may be harmful if inhaled or in-
gested, causing severe nausea,
fainting or poisoning.The harm-
fulelementsmay cause property
damage or severe injury.
STEP 1: Use detergent designed
specifically for pressure washers.
Household detergents could dam-
age the pump. Prepare detergent
solution as required by the manu-
facturer. Fill a container with pres-
sure washer detergent. Place the
filter end of detergent suction tube
into the detergent container.
STEP 2: Applysafetylatchtosprayguntrigger. Secure
black detergent nozzle into quick coupler. NOTE: De-
tergent cannot be applied using theYellow nozzle.
STEP 3: With the engine run-
ning,pulltriggertooperatema-
chine. Liquid detergent is
drawn into the machine and
mixed with water.Apply deter-
gent to work area. Do not al-
lowdetergenttodryonsurface.
IMPORTANT:You must flush the detergent injection
system after each use by placing the suction tube
into a bucket of clean water, then run the pressure
washer in low pressure for 1-2 minutes.
THERMAL PUMP PROTECTION
If you run the engine on your pressure washer for 3-5
minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach high tempera-
tures. When the water reaches this temperature, the
pump protector engages and cools the pump by dis-
charging the warm water onto the ground.This thermal
device prevents internal damage to the pump.
CLEANINGTIPS
Pre-rinse cleaning surfacewith freshwater.Placedetergent
suction tube directly into cleaning solution and apply to sur-
face at low pressure (for best results, limit your work area to
sections approximately 6 feet square and always apply de-
tergent from bottom to top). Allow detergent to remain on
surface 1-3 minutes. Do not allow detergent to dry on sur-
face. If surface appears to be drying, simply wet down sur-
face with fresh water. If needed, use brush to remove stub-
born dirt. Rinse at high pressure from top to bottom in an
even sweeping motion keeping the spray nozzle approxi-
mately1footfromcleaningsurface.Useoverlappingstrokes
as you clean and rinse any surface.For best surface clean-
ing action spray at a slight angle.
Recommendations:
• Beforecleaninganysurface, aninconspicuousarea
should be cleaned to test spray pattern and dis-
tance for maximum cleaning results.
• If painted surfaces are peeling or chipping, use ex-
tremecautionaspressure washermayremove the
loose paint from the surface.
• Keep the spray nozzle a safe distance from the sur-
face you plan to clean. High pressure wash a small
area, then check the surface for damage.If no dam-
age is found, continue to pressure washing.
CAUTION - Never use:
• Bleach, chlorine products and other corrosive
chemicals
• Liquids containing solvents (i.e., paint thinners,
gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the machine and will dam-
age the surface being cleaned.
RINSING
• It will take a few seconds for the detergent to clear.
Applysafety latchtospray gun.Remove blacksoap
nozzlefromthequickcoupler.Selectandinstallthe
desired high pressure nozzle.NOTE: You can also
stopdetergentfromflowingby simply removingde-
tergent siphon tube from bottle.
WARNING
DETERGENTS AND GENERAL OPERATINGTECHNIQUES

96-720, 97-708, 97-709, 97-710 • REV. 2/04 9
PRESSURE WASHER OPERATOR’S MANUAL
SHUTTING DOWN AND CLEAN-UP
STEP 1: Remove de-
tergent suction tube
from container and in-
sert into one gallon of
fresh water. Slide
nozzle forward for low
pressureortoconnect
black detergent
nozzle.Pull trigger on
spray gun and siphon
water for one minute.
STEP 2: Turn off machine by
flipping switch on rear of mo-
tor.
STEP 5: Disconnect the garden
hose from the water inlet on the
machine.
STEP 6: Disconnect the high
pressure hose from high pres-
sure outlet.
STEP 7: Engage
the spray gun
safety lock.
STEP 4: Press trigger
to release water pres-
sure.
Pump
Water
Inlet
High
Pressure
Outlet Safety
Latch
STORAGE
CAUTION
Pump Storage
CAUTION: Always store your pres-
sure washer in a location where the
temperature will not fall below 32° F
(0° C).The pump in this machine is
susceptible to permanent damage if
frozen.
FREEZEDAMAGE ISNOTCOVERED
BYWARRANTY.
If you must store your pressure washer in a location
where the temperature is below 32° F, you can mini-
mize the chance of damage to your machine by drain-
ing your machine as follows:
1. Stop the pressure washer and detach supply hose
andhigh pressure hose.Squeeze the triggerofthe
spray gun to drain all water from the wand and
hose.
2. Restartpressure washerandletit runbriefly(about
5 seconds) until water no longer discharges from
the high pressure outlet.
STEP 3: Turn off water supply.
On/Off
Switch

96-720, 97-708, 97-709, 97-710 • REV. 2/04
PRESSURE WASHER Troubleshooting Guide
10
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
PUMP RUNNING
NORMALLY BUT
PRESSURE LOW ON
INSTALLATION
Pump sucking air Check water supply and possibility of air seepage.
Check valves sticking Check and clean or replace if necessary.
Unloader valve seat faulty Check and replace if necessary.
Nozzle incorrectly sized Check and replace if necessary.
Worn piston packing Check and replace if necessary.
FLUCTUATING PRESSURE Valves worn Check and replace if necessary.
Blockage in valve Check and replace if necessary.
Pump sucking air Check water supply connections.
Worn piston packing Check and replace if necessary.
Insufficient water Check filter and hose for breakage.
PRESSURE LOW AFTER
PERIOD OF NORMAL USE Nozzle worn Check and replace if necessary.
Suction or delivery valves worn Check and replace if necessary.
Suction or delivery lines blocked Check and clean if necessary.
Unloader valve seat worn Check and replace if necessary.
Worn piston packing Check and replace if necessary.
Water temperature excessive Reduce to below 160o F.
PUMP NOISY Air in suction line Check water supply and connections on suction line.
Broken or weak suction or delivery
valve spring Check and replace if necessary.
Foreign matter in valves Check and clean if necessary.
Worn bearings Check and replace if necessary.
Excessive temperature of water Reduce to below 160o F.
PRESENCE OF WATER IN
PUMP OIL Oil seal worn Check and replace if necessary.
High humidity in air Check and replace if necessary.
Piston packing worn Check and replace if necessary.
WATER DRIPPING FROM
UNDER PUMP Piston packing worn Check and replace if necessary.
O-ring plunger retainer worn Check and replace if necessary.
WATER DRIPPING FROM
PUMP PROTECTOR Water supply pressure too high (over
90 PSI) Lower water supply pressure using a regulator.
Spray gun is in the off position for over
5 minutes Turn machine off if not in use for over 5 minutes.
OIL DRIPPING Oil seal worn Check and replace if necessary.
EXCESSIVE VIBRATION IN
HIGH PRESSURE HOSE Irregular functioning of the pump
valves Check and replace if necessary.
MOTOR DOES NOT START
WHEN SWITCHED ON Plug not well connected or lack of
power supply Check plug, cable and switch.
WHEN SWITCHING ON THE
MACHINE, MOTOR HUMS
BUT DOES NOT RUN
Main voltage is insufficient, lower than
the minimum required Check to make sure main power supply is adequate.
The pump is stuck or frozen Check by turning the motor manually.
MOTOR STOPS Tripped thermal overload due to
overheating Check that main voltage corresponds to the specifications. Wait a few minutes before turning on
the machine again by resetting the GFCI cord.

96-720, 97-708, 97-709, 97-710 • REV. 2/04 11
PRESSURE WASHER Troubleshooting Guide
PREVENTATIVE MAINTENANCE
Thispressurewasherwas produced with the best availablematerialsand quality craftsmanship.However,youas
the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative
maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for
maintenance.Regular preventative maintenance will add many hours to the lifeofyourpressure washer.Perform
maintenance more often under severe conditions.
OIL CHANGE RECORD
Check pump oil and engine oil level before first use of your new pressure washer.
Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
MAINTENANCE SCHEDULE
Pump Oil Inspect Daily inspect the oil level
Change After first 50 hours, then every 500 hours or annually
Replace High Pressure Nozzle Every 6 months
Replace Quick Connects Annually
Clean Water Screen/Filter Weekly
Replace HP Hose Annually if there is any sign of wear
Grease Motor Every 10,000 hours
PREVENTATIVE MAINTENANCE

96-720, 97-708, 97-709, 97-710 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
12
EXPLODED VIEW
1
3
2
19 18 17 16 15
14
13
25
24
23 26 27
10
9
11
10 12
39
38
37
35
34
36
8
34
39
40
33
28
29
31
30
42
44
49
40 50
51
52
48
49
48 47
45
46 44
43
59
58
53
56
57
54
48
49
4155
50 51
52
1-1/2HP
62
22
21
32
20
61
21
60
63
40
5
6,7
5
15 16
17
22
21
21
(Models 352007A,
352009A)
(Model 4-20021A)

96-720, 97-708, 97-709, 97-710 • REV. 2/04 13
PRESSURE WASHER OPERATOR’S MANUAL
EXPLODED VIEW PARTS LIST
ITEM PART NO. DESCRIPTION QTY
1 See Specifications Page 18, For Proper Size
4-12803015 Nozzle, 1503, Yellow 1
4-12803025 Nozzle, 2503, Green 1
4-12803040 Nozzle, 4003, White 1
4-12803000 Nozzle, 0003, Red 1
4-12804015 Nozzle, 1504, Yellow 1
4-12804025 Nozzle, 2504, Green 1
4-12804040 Nozzle, 4004, White 1
4-12804000 Nozzle, 0004, Red 1
4-12805015 Nozzle, 1505, Yellow 1
4-12805025 Nozzle, 2505, Green 1
4-12805040 Nozzle, 4005, White 1
4-12805000 Nozzle, 0005, Red 1
4-12805515 Nozzle, 1555, Yellow 1
4-12805525 Nozzle, 2555, Green 1
4-12805540 Nozzle, 4055, White 1
4-12805500 Nozzle, 0055, Red 1
4-12806015 Nozzle, 1506, Yellow 1
4-12805025 Nozzle, 2506, Green 1
4-12806040 Nozzle, 4006, White 1
4-12806000 Nozzle, 0006, Red 1
4-16540 Nozzle, Compl. QCME 6540,
Brass, All 1
2 4-011106 Wand, 18” M22 x 1/4” QC
(EP, PDE Models) 1
4-0110410 Wand, Straight, 31.4”SS (DE, DL
Models) 1
3 4-011137 Spray Gun, SK@, 3/8” Inlet,
Lance w/M22 Coupler (EP, PDE
Models) 1
4-01246 Spray Gun Shut-Off, AP1000
(DE, DL Models) 1
4 Hose, See Specifications Page 18
5 6-051591 Connector, 1/2” L/T, 90°,
Black 2
6 6-0104 Cord, Service, SOWA 12/3,
Coleman 1.75 ft.
7 6-0128 Conduit, Watertight, Flex, 1/2,
100’Box .66 ft.
8 90-2000 Nut, 1/4” ESNA, NC 4
9 3-12021 Injector, Chem, Non Adjust.,
3-5GPM, .083 ( Models
301509A, 352009A,
352007A) 1
3-1202 Injector, Chem, Non Adjust.,
(201009D, 201007D, 301009D,
301007D, 201507D) 1
10 2-9040 Clamp, Hose, .46 - .54ST,
(823988) 2
11 4-02080000 Tube, 1/4” x 1/2” Clear
Vinyl 6 ft.
12 2-1904 Strainer, Plastic, 1/4” Hose
Barb 1
13 90-017 Nut, 10/32” Keps 6
14 90-1991 Screw, 10/32” x 1/2” BHSOC
Black 4
ITEM PART NO. DESCRIPTION QTY
15 6-020204 Switch, 2 Pos. 120V-600V,
1-3Ph Bremas 1
16 6-03911 Lid, Plastic, Carlon E9801
Box 1
17 6-03910 Box, Plastic, Carlon E9801,
w/o Lid 1
18 90-19713 Screw, 5/16” x 3/4” Whiz 4
19 95-07500186 Bracket, Switch Box 1
20 6-010631 GFCI, 240V 1Ph 20A, 36’
12-3 Cord (301509A) 1
6-01059 GFCI, 240V 1Ph 30A, 36’ 10-3
Cord (352007A, 352009A) 1
6-01060 GFCI, 120V 20A, w/36’ 12-3
Cord (301009D, 301007D,
201507D) 1
6-01062 GFCI, 120V 15A, w/36’
12-3 Cord (201009D,
201007D) 1
21 10-08021 Label, Disconnect Power
Supply 1
22 95-07105000 Cover, Motor 1
23 2-2006 Nipple, 3/8” x 3/8” NPT, ST
Female 1
24 2-10943 Swivel, 3/8” MP x 3/4” GHF
w/Strainer 1
25 2-300816 Protector, Pump, 3/8” PTP1
26 Unloader, See Specifications Page 18
27 Pump, See Specifications Page 18
28 90-1016 Bolt, 3/8” x 1” NC 4
29 90-4002 Washer, 3/8” SAE, Flat 4
30 90-1006 Bolt, 5/16” x 3/4” NC 4
90-1016 Bolt, 3/8” x 1” NC HH (352007A,
352009A) 4
31 90-4001 Washer, 5/16” Flat 4
90-4002 Washer, 3/8” SAE, Flat
(352007A,352009A) 4
32 Unloader, See Specifications Page 18
33 2-0103 Grommet, Rubber, Nozzle
Holder 5
34 90-20012 Nut, 5/16” Flange, Whiz
Loc 2
35 95-07104921 Handle, Grab, Red1
95-07104961 Handle, Grab, Chrome 1
36 11-0362 Label (EP Models) 1
11-08022 Label (PDE Models) 1
11-0361 Label (DE Models) 1
11-0363 Label (DL Models) 1
37 95-07104945 Plate, Warning/Instr. Red (EP,
DE, DL) 1
95-07104966 Plate, Warning/Instr. Blk
(PDE) 1

96-720, 97-708, 97-709, 97-710 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
14
ITEM PART NO. DESCRIPTION QTY
38 95-07102382 Hanger, Hose/Wand, CG/
CV 1
39 90-100471 Bolt, Carriage, 1/4”-20 x
1-1/2” 4
40 90-10072 Bolt, Carriage, 5/16” x 2”, NC,
Zinc 6
41 90-2001 Nut, 5/16” ESNA, NC 8
42 95-07104920 Handle, Lower Grab, Red 1
95-07104950 Handle, Lower Grab, Black 1
43 95-07104923 Retainer Bracket, Handle,
Red 2
95-07104924 Retainer Bracket, Handle,
Black 2
44 90-1020 Bolt, 3/8” x 2” 4
45 90-10201 Bolt, 3/8” x 2-1/4” 2
46 90-40125 Washer, 3/8” x 1” 1
47 2-01041 Pad, Soft Rubber, 50 Duro 2
48 90-4002 Washer, 3/8” SAE, Flat
(780562) 6
49 90-2002 Nut, 5/16” ESNA, NC 2
50 90-200422 Cap, 5/8” Axle Hub, Black 2
51 4-0303 Wheel & Tire Assy., 4” Steel Rim
w/Tube 2
52 2-001403 Bushing, 1/2” Axle, 1/2” x 5/8” x
3/4” w/Flange 2
53 6-05152 Strain Relief, (1-1/2HP Models
Only) 1
54 95-07102313 Axle, 5/8” x 19.625” Long 1
55 90-4001 Washer, 5/16” Flat, SAE
(780452) 8
ITEM PART NO. DESCRIPTION QTY
56 95-07104922 Handle, Bumper, Red (EP, DL
DE Models) 1
95-07104962 Handle, Bumper, Chrome (PDE
Models) 1
57 95-07104927 Base, CW Direct, Red (EP, DL
DE Models) 1
95-07104965 Base, CW Direct, Black (PDE
Models) 1
58 10-08017 Label, Intended For Outdoor
Use 1
59 10-9999 Label, Clear Lexan, 2-1/4” x
4-1/2” 1
60 6-02049 Switch Assembly 1
61 10-08018 Label, Warning, Service
Cord 1
62 6-05154 Strain Relief, Flex 90°, Plastic
P/N 3266 1
63 6-05152 Strain Relief 1
64 10-08028 ▲ Tag, Pump/Plug Dipstick 1
6-0501 ▲ Wire Nut, Brown, Twister,
8-22 AWG 1
6-05034 ▲ Terminal, Ring Tongue,
10RC-10 1
6-05034 ▲ Terminal, Ring Tongue,
10RC-10 2
6-05181 ▲ Locknut, 1/2” Conduit 1
90-100030 Screw, 10/32” x 3/4” Slot Pan,
MS, SS 1
11-1042 ▲ Label, Ground 1
▲ Not Shown

96-720, 97-708, 97-709, 97-710 • REV. 2/04 15
PRESSURE WASHER OPERATOR’S MANUAL
HOSE AND SPRAY GUN ASSEMBLY
HOSE AND SPRAY GUN ASSEMBLY PARTS LIST
ITEM PART NO. DESCRIPTION QTY
1 2-2002 Coupler, 3/8" Female 1
2-0121 ▲Quick Coupler O-Ring 1
2 4-0203050C Hose, 50' x 3/8" w/Coupler( EP,
PDE, DL Models) 1
4-02093450BC Hose, 50’ x 3/8” w/Coupler (DE
Models) 1
3 4-011137 Spray Gun, Shut-Off 1
4 4-011106 Wand, Straight 1
ITEM PART NO. DESCRIPTION QTY
5 2-2000 Coupler, 1/4” Female 1
2-0119 Quick Coupler O-Ring 1
6 Nozzle, See Page 18 For Size
7 4-16540 Nozzle, Brass Soap 1
▲Not Shown
6
2
3
7
5
1
4

96-720, 97-708, 97-709, 97-710 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
16
PDE4-30025A, B, C EXPLODED VIEW
32
3
43
25
27
26 6
23
28 45
9
41
7
19
31
46
24
30
8
44
33
29
32
16
30
32
16
32
30
30
30
30
48
32 48
37
8
33
29
13
34
29 30
32
36
21
18
12
35
1
10
4
2
14 22
20
32
28
15
5
42 17
47
48
49
50 39
40
38
32
28
32
30
30
51

96-720, 97-708, 97-709, 97-710 • REV. 2/04 17
PRESSURE WASHER OPERATOR’S MANUAL
ITEM PART NO. DESCRIPTION QTY
1 10-020PDE Label, PDE, Lexan 1
2 2-1902 Strainer, Inlet Garden Hose 1
3 6-010690 Cord w/GFCI, 240V, 30 Amp
TRC (4-3000A) 1
6-0109 Cord, Service, SEO 10/4
(4-3000B) 15 ft.
6-0105 Cord, Service 12/4
(4-3000C) 15 ft.
4 10-2043000 Label, 4-3000 (Lexan) 1
5 2-10942 Swivel, 1/2" MP x 3/4" GHF
W/Strainer 1
6 6-5012 Overload, 18.00 - 24 Amp
(4-3000B) 1
6-5009 Overload, 7.50 - 11 Amp
(4-3000C) 1
7 10-08018 Label, Warning, Service
Cord 1
8 90-2004 Nut, 5/8", Jam, ESNA, NF 2
9 6-021595 Din Rail, 35mm 4"
10 10-99060 Label, Oper Inst/Warn 1
11 90-017 ▲Nut, 10/32" KEPS 6
90-1994 ▲Screw, 10/32" XD 1-1/4" 1
90-1991 ▲Screw, 10/32" x 1/2",
BHSOC B1 7
12 2-0103 Grommet, 1/8" Rubber 2
13 2-01041 Pad, Soft Rubber, 50 Duro 2
14 2-2006 Nipple, 3/8" x 3/8" NPT ST
Female 1
15 2-30082 Pump Protector, 1/2" PTP 1
16 4-0303 Wheel, 4" Steel Rim 2
17 4-12804015 Nozzle, SAQCMEG 1504,
Yellow (4-3000) 1
18 4-16540 Nozzle Compl, Q CEM-6540
w/Black Nylon 1
19 5-10130 MTR 7.5 HP 1 PH C-Face
1725RPM, 37N07X177
(4-30025A) 1
5-10143 MTR 7.5 HP 3 PH C-Face 1725
RPM, 37B12X54G1
(4-30025B, C) 1
6-05171 ▲Strain Relief, 1"
(4-3000B/C) 1
20 5-2263 Pump, AR RKA35G30E-
F17 1
21 10-08028 Tag, Remove Pump Plug 1
22 5-3203 Unloader, AR-20242G, 3-4 GPM/
3500 PSI, Black Knob 1
23 6-2021 Switch, GRN PB, CH 1
24 6-2022 Switch, Red PB, CH 1
ITEM PART NO. DESCRIPTION QTY
25 6-03904 Enclosure, Fiberglass,
NEMA4X 1
11-1042 ▲Label, Ground 1
26 10-08015A Label, PE Off/On, For Push
Buttons 1
27 10-08021 Label, Disconnect Power
Supply 1
28 90-1016 Bolt, 3/8" x 1", NC HH 8
29 90-1020 Bolt, 3/8" x 2", NC HH 8
30 90-2002 Nut, 3/8", ESNA, NC 18
31 6-2000 Block, Contact, N/C 1
32 90-4002 Washer, 3/8", SAE, Flat 34
33 90-4005 Washer, 5/8", Flat, SAE 4
34 90-40125 Washer, 3/8" x 1" Steel 2
35 95-07101133 Handle, Grab, 1-1/4", Black 1
36 95-07101219 Foot Bracket, Wide Foot 1
37 95-07101216 Frame, Small, Welded 1
38 90-4015 Washer, 7/16" x 2-1/2" 2
39 95-07161114A Tube Foot 2
40 90-5009 Spring Foot 2
41 6-05172 Locknut, 3/4", Conduit 2
42 6-051595 Strain Relief, STRT, LQ Tite2
6-05170 Strain Relief, 3/4", Water Tite
(4-3000A) 1
43 6-4019 Contactor, 240V, CH,
CE15HNS3BB-09
(4-3000A) 1
6-4011 Contactor, 240V, CH,
CE15FNS3BB (4-3000B) 1
6-4009 Contactor, 480V, CH
CE15DNS3CB (4-3000C) 1
44 95-07101131 Handle, Bumper, 1-1/4" 1
45 95-07101021 Bracket, Elec. Box PE, PDE1
46 6-2001 Block, Contactor, N/O 1
47 90-102702 Bolt, 1/2" x 1-1/2" NC HH
Zinc 4
48 90-40091 Washer, 1/2" 4
49 90-1023 Bolt, 3/8" x 5", NC 2
50 2-0107 Bellows, Leg Boot 2
51 6-0102 Cord, Service, 8/3
(4-3000A) 2.75 ft.
6-0105 Cord, Service, 12/4
(4-3000C) 2.75 ft.
6-0109 Cord, Service 10/4
(4-3000B) 2.75 ft.
▲Not Shown

96-720, 97-708, 97-709, 97-710 • REV. 2/04
PRESSURE WASHER Specifications
18
SPECIFICATIONS
Machine Pessure Nozzle Pump Pump Unloader Motor Motor
Model GPM (PSI) Size Hose p/n Part # Model Part # Hp Part #
EP-201009D 2.0 1000 4.0 4-0203050C 5-1802 HC205AL 5-3303 1-1/2 5-1004M
EP-301009D 3.0 1000 6.0 4-0203050C 5-1806 HC235 5-3303 2 5-1073
EP-301509A 3.0 1500 5.0 4-0203050C 5-1806 HC235 5-3303 3 5-10081
EP-352009A 3.5 2000 5.0 4-0203050C 5-1803 HC450R 5-3303 5 5-10104
PDE2-11021D 2.0 1000 4.0 4-0203050C 5-23001 TT9061EBF 5-3025 1-1/2 5-1004M
PDE2-15021D 1.9 1500 3.0 4-0203050C 5-23001 TT9061EBF 5-3024 2 5-1047
PDE4-20021A 3.5 2000 5.0 4-0203050C 5-2303 TT2035EBF 5-3024 5 5-1053
PDE4-30025A 3.5 3000 4.0 4-0203050C 5-2263 RKA35G30E-17 5-3203 7-1/2 5-10130
PDE4-30025B 3.5 3000 4.0 4-0203050C 5-2263 RKA35G30E-17 5-3203 7-1/2 5-10143
PDE4-30025C 3.5 3000 4.0 4-0203050C 5-2263 RKA35G30E-17 5-3203 7-1/2 5-10143
DL-201007D 2.0 1000 4.0 4-020650C 5-1618 WMH-2521-F 5-3150 1-1/2 5-1004M
DL-201507D 1.9 1500 3.0 4-020650C 5-1618 WMH-2521-F 5-3150 2 5-1047
DL-301007D 2.8 1000 5.5 4-020650C 5-1620 WMH-1528-F 5-3150 2 5-1047
DL-352007A 3.5 2000 5.0 4-020650C 5-1621 WMH-2035-F 5-3150 5 5-1043
DE-201007D 2.0 1000 4.0 4-02093450BC 5-1618 WMH-2521-F 5-3150 1-1/2 5-1004M
DE-201507D 1.9 1500 3.0 4-02093450BC 5-1618 WMH-2521-F 5-3150 2 5-1047
DE-301007D 2.8 1000 5.5 4-02093450BC 5-1620 WMH-1528-F 5-3150 2 5-1047
DE-352007A 3.5 2000 5.0 4-02093450BC 5-1621 WMH-2035-F 5-3150 5 5-1043

DE SERIES PRESSUREWASHER
WARRANTY
SHARK LIMITED NEW PRODUCTWARRANTY
PRESSURE WASHERS
WHAT THIS WARRANTY COVERS
All SHARK PRESSURE WASHERS are warranted by SHARK to the original purchaser to be free from defects in materials and
workmanship under normal use, for the periods specified below.This Limited Warranty is subject to the exclusions shown below,
is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced under this
warranty will assume the remainder of the part’s warranty period. This warranty applies to the original purchaser and is not
transferable. LIMITED LIFETIME PARTS WARRANTY:
Components manufactured by SHARK, such as frames, handles, coil wraps, float tanks, and belt guards. Forged brass pump
manifold.All heating coils will have a three year warranty.Internal components on the oil-end of all pressure washer pumps will
have a seven year warranty. ONE YEAR PARTS WARRANTY:
All other components, excluding normal wear items as described below, will be warranted for one year on parts. Warranty on
these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty.
WARRANTY PROVIDED BY OTHER MANUFACTURERS:
Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manufac-
turers’ local authorized service centers. SHARK cannot provide warranty on these items.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover the following items:
1. Normal wear items, such as nozzles, guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings,
packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protectors.
2. Damage or malfunctions resulting from accidents, abuse, modifications, alterations, incorrect installation, improper
servicing, failure to follow manufacturer’s maintenance instructions, or use of the equipment beyond its stated usage
specifications as contained in the operator’s manual.
3. Damage due to freezing, chemical deterioration, scale buildup, rust, corrosion, or thermal expansion.
4. Damage to components from fluctuations in electrical or water supply.
5. Normal maintenance service, including adjustments, fuel system cleaning, and clearing of obstructions.
6. Transportation to service center, shop labor charges, field labor charges, or freight damage.
WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE
While not required for warranty service, we request that you register your SHARK pressure washer by returning the completed
registration card. In order to obtain warranty service on items, you must return the product to an Authorized SHARK Dealer,
freight prepaid, with proof of purchase, within the applicable warranty period. If the product is permanently installed, you must
notify your Authorized SHARK Dealer of the defect.The Authorized Dealer will file a claim, which must subsequently verify the
defect.In most cases, the part must be returned to SHARK freight prepaid with the claim.For warranty service on components
warranted by other manufacturers, the Authorized Dealer can help you obtain warranty service through these manufacturers’
local authorized service centers. If you are unable to resolve the warranty claim satisfactorily, write to SHARK at 4275 N.W.
Pacific Rim Blvd., Camas, WA 98607, ATTN: Warranty Dept., detailing the nature of the defect, the name of the Authorized
Dealer, and a copy of the purchase invoice. LIMITATION OF LIABILITY
SHARK’S liability for special, incidental, or consequential damages is expressly disclaimed. In no event shall SHARK’S liability
exceed the purchase price of the product in question. SHARK makes every effort to ensure that all illustrations and specifica-
tions are correct, however, these do not imply a warranty that the product is merchantable or fit for a particular purpose, or that
the product will actually conform to the illustrations and specifications.THEWARRANTY CONTAINED HEREIN IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A PAR-
TICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representation or
promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way.It is the buyer’s responsibility to ensure
that the installation and use of SHARK products conforms to local codes. While SHARK attempts to assure that its products
meet national codes, it cannot be responsible for how the customer chooses to use or install the product.
SHARK PRESSURE WASHERS
1-360-833-9100 • 1-800-771-1881 • www.shark-pw.com
SHARK DE • 97-710 • REV. 2/04
PRESSURE WASHER WARRANTY

Form#97-710 • Revised2/04 • Printedin U.S.A.