Shark DE-2010 User manual

SHARK PRESSURE WASHERS
■
4275 N.W. Pacific Rim Blvd.
■
Camas,WA 98607
■
USA
For technical assistance or the Shark Dealer nearest you, call 1-800-771-1881.
MODEL: DE
OPERATING INSTRUCTION
AND PARTS MANUAL
■ DE-2010 ■ DE-2015

2
MACHINE SPECIFICATIONS
Shark DE Manual • Form #97-6127 • Revised 10/02
●●
●●
●Pump Volume At Pump Head:
DE-2010 2.0 GPM
DE-2015 1.9 GPM
●●
●●
●Pump Pressure At Pump Head:
DE-2010 1000 PSI
DE-2015 1500 PSI
● ●
● ●
● Machine Dimensions: DE-2010 Length = 32.5" Width = 19.5" Height = 23.5"
DE-2015 Length = 32.5" Width = 19.5" Height = 23.5"
●●
●●
●Machine Voltage:
DE-2010 120V/1PH
DE-2015 120V/1PH
●●
●●
●Total Machine Amperage:
DE-2010 15 Amps
DE-2015 18 Amps

3
CONTENTS
Shark DE Manual • Form #97-6127 • Revised 10/02
SERIAL NUMBER:
DATE PURCHASE:
FOR SALES AND SERVICE, PLEASE CONTACT:
Introduction ............................................................. 4
Important Safety Information ............................... 4-5
Pre-Operation Check .............................................. 5
Setup Procedures ................................................... 5
Operating Instructions ............................................ 5
General Washing Techniques ................................. 5
Shutdown Procedures ............................................ 5
Component Identification ........................................ 6
How To Use the Detergent Injector ......................... 7
Exploded View ........................................................ 8
Parts List, Exploded View ....................................... 9
Hose & Spray Gun Assembly ............................... 10
Downstream Injector Assembly ............................ 11
Troubleshooting .................................................... 12
Preventative Maintenance .................................... 13
Oil Change Record ............................................... 13
Warranty

4 DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
Shark DE •Rev. 10/02
INTRODUCTION
Thank you for purchasing a Shark Pressure Washer.
This manual covers the operation and maintenance of
the DE-201001D and DE-201501D washers. All infor-
mation in this manual is based on the latest product in-
formation available at the time of printing.
Shark reserves the right to make changes at any time
without incurring any obligation.
The DE Series was designed for a maximum
use of 4 hours per day, 5 days per week.
Owner/User Responsibility:
The owner and/or user must have an understanding of
the manufacturer’s operating instructions and warnings
before using this Shark pressure washer.Warning infor-
mation should be emphasized and understood. If the
operator is not fluent in English, the manufacturer’s in-
structions and warnings shall be read to and discussed
with the operator in the operator’s native language by
the purchaser/owner, making sure that the operator com-
prehends its contents.
Owner and/or user must study and maintain for future
reference the manufacturers’ instructions.
This manual should be considered a permanent
part of the machine and should remain with it if
machine is resold.
When ordering parts, please specify model and
serial number.
IMPORTANT SAFETY
INFORMATION
CAUTION: To reduce the risk of
injury, read operating instruc-
tions carefully before using.
1. Read the owner's manual thor-
oughly. Failure to follow in-
structions could cause mal-
function of the machine and
result in death, serious bodily
injury and/or property damage.
2. All installations must comply with local codes. Con-
tact your electrician, plumber, utility company or the
selling distributor for specific details.To comply with
the National Electrical Code (NFPA 70) and provide
additional protection from risk of electric shock,
single phase pressure washers are equipped with
a UL approved ground fault circuit interrupter (GFCI)
power cord. Three phase machines must be con-
nected to a GFCI circuit breaker.
WARNING
HIGH PRESSURE
SPRAY CAN PIERCE
SKIN AND TISSUES.
WARNING: Flammable liquids
can create fumes which can ig-
nite causing property damage or
severe injury.
WARNING: Risk of explosion —
Do not spray flammable liquids.
3. Risk of explosion — do not
spray flammable liquids or
operate in an area where
flammable or explosive materials are used or stored.
WARNING: Keep water spray
away from electrical wiring or
fatal electric shock may result.
4. To protect the operator from
electrical shock, the machine
must be electrically grounded.
It is the responsibility of the
owner to connect this machine
to a UL grounded receptacle of
proper voltage and amperage ratings.
Do not spray water on or near electrical components.
Do not touch machine with wet hands or while stand-
ing in water. Always disconnect power before ser-
vicing.
5. Grip cleaning wand securely with both hands before
starting the cleaner. Failure to do this could result in
injury from a whipping wand.
WARNING: High pressure stream
of fluid that this equipment can
produce can pierce skin and its
underlying tissues, leading to
serious injury and possible
amputation.
6. High pressure developed by
these machines will cause
personal injury or equipment
damage. Use caution when operating. Do not direct
discharge stream at people, or severe injury or death
will result.
7. Never make adjustments on machine while in
operation.
WARNING: High pressure spray
can cause paint chips or other
particles to become airborne and
fly at high speeds.
8. Eye safety devices, foot protec-
tion and protective clothing
must be worn when using this
equipment.
9. Do not operate with the trigger
in the off position for extensive periods of time as
this may cause damage to the pump.
READ OPERATOR’S
MANUALTHOROUGHLY
PRIOR TO USE.
CAUTION
WARNING
RISK OF EXPLOSION:
DO NOT SPRAY
FLAMMABLE LIQUIDS.
WARNING
PROTECTIVE
EYEWEAR AND
CLOTHING MUST BE
WORN.
WARNING
KEEP WATER SPRAY
AWAY FROM
ELECTRICAL WIRING.

DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
5
Shark DE •Rev. 10/02
10. The best insurance against an accident is precau-
tion and knowledge of the machine.
11. Shark will not be liable for any changes made to our
standard machines, or any components not pur-
chased from Shark.
12. Be certain all quick coupler fittings are secured be-
fore using pressure washer.
13. Never run pump dry or leave spray gun closed longer
than 5 minutes.
14. Inlet water supply must be cold and clean fresh wa-
ter.
15. Do not allow children to operate the pressure washer
at any time.
16. Protect from freezing.
17. When the machine is working, do not cover or place
in a closed space where ventilation is insufficient.
PRE-OPERATION CHECK
❑Pump oil (SAE 30W non-detergent oil)
❑Clean, fresh, cold water supply
(5 GPM • 5/8" • 20 PSI)
❑Hose, wand, nozzle (nozzle size per serial plate)
❑Water filter (intact, non restrictive)
❑Proper electrical supply, receptacle and circuit
breaker.
SETUP PROCEDURES
These machines are designed for indoor use.
Machine must be stored indoors when not in use.
1. Attach a 5/8" garden hose to inlet connector. Mini-
mum flow should be 5 GPM.
2. Attach high pressure hose to discharge nipple using
quick coupler. Lock coupler securely into place by
pulling back coupler collar and inserting it onto dis-
charge nipple, then pushing collar forward to lock in
place.
3. Attach wand to spray gun using teflon tape on threads
to prevent leakage.
4. Attach connector on discharge hose to spray gun
using teflon tape on threads.
5. Remove oil plug on top of pressure washer pump
and replace with dipstick supplied. (This may be
installed from the factory.)
6. Check oil level on oil dipstick on top of pump. Oil
should be visible one half way up sight glass (30W
non-detergent).
7. For operator safety and to comply with electrical stan-
dards, each cord comes with a 120V/20 amp plug
end that will fit only into a 20 amp receptacle.
8. On 230V machines, attach appropriate plug end (not
included) to power cord.
OPERATING INSTRUCTIONS
1. With power switch in OFF position, plug power cord
into a grounded type of receptacle of proper voltage
and amperage reading. Then push GFCI reset but-
ton at end of power cord if required.
2. Turn on water at faucet and pull trigger on spray gun
allowing water to flow until all air has discharged from
system. Check for water leaks; tighten as needed.
3. Pull wand coupler collar back and insert pressure
nozzle into coupler then secure by pushing collar
forward.
4. With spray gun off, turn power switch to ON position
and check for leaks.
5. With spray nozzle pointed away from you or any-
body else, pull trigger on spray gun to obtain pres-
surized spray.
GENERAL WASHING
TECHNIQUES
Hold spray nozzle approximately one foot from the sur-
face being cleaned. Spray at an angle to get under the
material and lift it off.
When washing large objects, use detergent injector to
apply detergent (see section “How to Use the Detergent
Injector”). Start washing from the bottom and work up.
Better detergent economy and faster results will be
obtained by allowing the detergent to set 5-10 minutes.
After washing, rinse from the top down.
Cleaning heavy dirt or material away with a hard stream
of clear water is recommended before using a cleaning
agent.
SHUTDOWN PROCEDURES
1. Rinse all lines (and injector) with clean water, to re-
move any soap residue.
2. Turn power switch to OFF position.
3. Turn off water supply.
4. Open spray gun to relieve remaining pressure.
5. Remove water supply hose.
6. In freezing conditions, disconnect water supply and
open spray gun to allow water to drain, then turn off
motor.
CAUTION: Do not allow pump to run longer than 5
minutes without water. Disconnect all hoses to al-
low water to drain.
CAUTION: With machine off, open spray gun to
release pressure before removing discharge hose.

6 DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
Shark DE •Rev. 10/02
COMPONENT IDENTIFICATION
ALL MODELS
Spray Gun
High Pressure
Nozzle
Soap Nozzle
Unloader
Water Supply
Hose
(not included)
Detergent
Injector
GFCI
Trigger
Power
Supply
Detergent
Bucket
(not included)
Nozzle Quick
Coupler
Wand
Water
Supply
Plug
Nozzle

DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
7
Shark DE •Rev. 10/02
High Pressure
Hose
Detergent
Bucket
(not included)
Trigger
Nozzle
Quick Coupler
High Pressure Nozzle
Quick
Coupler
Detergent
Injector
Discharge
Nipple
Wand
HOW TO USE
THE DETERGENT INJECTOR
WARNING: Some detergents may
be harmful if inhaled or ingested
causing severe nausea, fainting
or poisoning. The harmful ele-
ments may cause property dam-
age or severe injury.
The machine can siphon and mix
detergents with the use of Shark's
detergent injector kit.
1. Pull injector quick coupler collar back and secure on
discharge nipple. Injector valve body arrow should
point in direction of flow.
2. Connect high pressure hose to injector nipple se-
curing quick coupler.
3. Start machine as outlined in Operating Instructions.
4. Place detergent pickup tube into container of deter-
gent solution.
5. Install the brass soap nozzle provided with the in-
jector into the quick coupler of the wand.
6. Open spray gun. Water detergent ratio is approxi-
mately 15 to 1.
7. When you finish washing, rinse by simply releasing
the spray gun, removing the soap nozzle, and re-
placing the pressure nozzle back into quick coupler.
NOTE: The detergent injector will not siphon with
the high pressure nozzle at the end of the wand.
8. If your machine has a variable pressure wand, turn
the pressure control handle counterclockwise to
lower the pressure. This directs the water flow
through the soap nozzle, allowing the detergent in-
jector to siphon soap. To rinse with high pressure
water, simply turn the control handle clockwise.
9. For clean up, place detergent pickup tube into con-
tainer of clear water and follow steps 5 and 8 to pre-
vent detergent deposits from damaging the injector.
WARNING
SOME DETERGENTS
MAY BE HARMFUL
IF INHALED OR
INGESTED
Spray
Gun
Inlet
Filter Detergent
Pick Up
Tube
Soap Nozzle

8 DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
Shark DE •Rev. 10/02
EXPLODED VIEW
ALL MODELS
23
11
12
30
31 11
29
3
20
23
21
22
13
11
14
18
17
16
19
2
3
4
5
14 15
12
1
6
7
10
11
8
9
28
27
26
23
22
25
24
33
On/Off Switch
Model
201001D
35
41
39
42
39
43
36
37
38
40
44
23
14
34
32

DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
9
Shark DE •Rev. 10/02
ITEM PART NO. DESCRIPTION QTY
1 5-1046 Motor 1.5 HP, 3450 RPM, Baldor
(2010) 1
5-1047 Motor 2 HP, 3450 RPM, Baldor
(2015) 1
2 90-1006 Bolt, 5/16" x 3/4" NC GR 5
CS ZN 4
3 90-4001 Washer, 5/16", Flat, SAE 8
4 6-01041 Cord, Electric 12/3 SJOWA
(2015) 3 Ft
5 6-051595 Strain Relief, LQ TITE, Large
(2010) 2
6 5-23001 Pump, General TT9061 EBF
(201001D, 201501D) 1
5-1618 Pump, Legacy WMH-2521-F
(201007, 201507) 1
7 2-300816 Pump Protector, 3/8" PTP
(201001, 201501) 1
2-30082 Pump Protector, 1/2"
(201007, 201507) 1
8 2-10943 Swivel, 3/8" MPX x 3/4" GHF
w/Strainer (201001, 201501) 1
2-10942 Swivel, 1/2" MP x 3/4" GHF
w/Strainer (201007, 201507) 1
9 5-3024 Unloader, PA, YVB135L TT
(201001, 201501) 1
5-3150 Unloader, APR 2300
(201007, 201507) 1
10 2-2006 Nipple, 3/8" x 3/8" NPT ST Fem 1
11 90-20041 Collar, 5/8" Bore Shaft 3010 4
12 4-0303 Wheel & Tire Assy, 4" w/Tube 2
13 95-07111117 Bracket, Switch Box (2015) 1
14 90-1991 Screw, 10/32" x 1/2"
BHSOC BLK (2015) 7
15 90-2018 Nut, Cage, 10/32" x 16 GA
(2015) 4
16 6-03910 Box, Plastic, Carlon w/o Lid
(2015) 1
11-1042 ▲ Label, Ground 1
17 6-03911 Lid, Plastic, Carlon Box
(2015) 1
18 6-020204 Switch, 2 Pos. 120V-600V,
1-3PH (2015) 1
19 95-07200025 Frame, Assy 1
20 95-07101136 Axle, 5/8" x 18" Long 1
EXPLODED VIEW PARTS LIST
ALL MODELS
ITEM PART NO. DESCRIPTION QTY
21 90-2001 Nut, 5/16", ESNA, NC 4
22 90-1020 Bolt, 3/8" x 2", NC HH 4
23 90-4002 Washer, 3/8", Flat, SAE 14
24 90-2002 Nut, 3/8", ESNA, NC 6
25 95-07200021 Handle, Assy, Grab 1
26 4-12804015 Nozzle, SAQCMEG, 1504,
Yellow (DE-2010) 1
4-12803015 Nozzle, SAQCMEG, 1503,
Yellow (DE-2015) 1
27 4-16540 Nozzle, Compl. QCEM-6540
Brass 1
28 2-0103 Grommet, Rubber
(Nozzle Holder) 2
29 2-01041 Pad, Soft Rubber, 50 Duro 2
30 6-01060 GFCI, 120V 20 Amp, w/36'
12-3 Cord (2015) 1
6-01062 GFCI, 120V 15 Amp, w/36'
12-3 Cord (2010) 1
31 10-08018 Label, Warning, Service Cord 1
32 90-400012 Washer, #10 4
33 90-1017 Bolt, 3/8" x 1-1/4" NC 2
34 90-017 Nut, 10/32", Keps 2
35 6-02049 Switch, Toggle (2010) 1
36 10-08016 Label, Intended For Indoor Use 1
37 10-08018 Label, Clear Lexan 1
38 11-0309 Label, Nozzle, OPS, Warning 1
39 2-01403 Bushing, Snap, 5/8" 2
40 2-1044 Plug, 1/8" Countersunk
(201001, 201501) 1
2-1046 Plug, 1/4" Countersunk
(201007, 201507) 1
41 6-05153 Strain Relief, LQ TITE 3200
(2010) 1
42 6-05154 Strain Relief, Flex, 90° (2015) 1
43 90-40125 Washer, 3/8" x 1" 2
44 90-1016 Bolt, 3/8" x 1" 4
▲ Not Shown

10 DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
Shark DE •Rev. 10/02
ITEM PART NO. DESCRIPTION QTY
1 2-2000 Coupler, 1/4" Female, Brass 1
2-0119 ▲ O-Ring, Quick Coupler,
1/4" Viton 1
2 4-0110531 Wand, 15.5", Half, w/Coupler,
Nozzle Side 1
3 4-0110532 Wand, 15.5", Half,
Spray Gun Side 1
4 4-01246 Spray Gun, Shut-Off, AP-1000 1
5 4-02093450BC Hose, 3/8" x 50', 1 Wire,
w/Coupler 1
HOSE & SPRAYGUN ASSEMBLY
ALL MODELS
ITEM PART NO. DESCRIPTION QTY
6 2-2002 Coupler, 3/8" Female, Brass 1
2-0121 ▲ O-Ring, Quick Coupler,
3/8" Viton 1
7 Nozzles, See Exploded View
Parts Breakdown
8 4-16540 Nozzle Compl. QCEM-6540
Brass 1
9 4-011183 Detergent Injector Assy 1
10 2-1014 Coupling, 1/4" Hex 1
▲ Not Shown
4
5
8
9
6
1
2
7
3
10

DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
11
Shark DE •Rev. 10/02
DOWNSTREAM INJECTOR ASSEMBLY
ITEM PART NO. DESCRIPTION QTY
1 3-1202 Detergent Injector, 2-3 GPM, 0.70 1
2 2-9000 Clamp, Screw, #4 2
3 4-02080000 Tube, 1/4" x 1/2", Clear Vinyl /ft. 6
4 2-1904 Strainer, 1/4", Hose Barb 1
3
1
2
4
2

12 DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
TROUBLESHOOTING
Shark DE •Rev. 10/02
PROBLEM POSSIBLE CAUSE SOLUTION
PUMP RUNNING
NORMALLY BUT
PRESSURE LOW ON
INSTALLATION
Pump sucking air Check water supply and possibility of air seepage.
Check valves sticking Check and clean or replace if necessary.
Unloader valve seat faulty Check and replace if necessary.
Nozzle incorrectly sized Check and replace if necessary.
Worn piston packing Check and replace if necessary.
FLUCTUATING PRESSURE Valves worn Check and replace if necessary.
Blockage in valve Check and replace if necessary.
Pump sucking air Check water supply connections.
Worn piston packing Check and replace if necessary.
Insufficient water Check filter and hose for breakage.
PRESSURE LOW AFTER
PERIOD OF NORMAL USE
Nozzle worn Check and replace if necessary.
Suction or delivery valves worn Check and replace if necessary.
Suction or delivery lines blocked Check and clean if necessary.
Unloader valve seat worn Check and replace if necessary.
Worn piston packing Check and replace if necessary.
Water temperature excessive Reduce to below 160o F.
PUMP NOISY Air in suction line Check water supply and connections on suction line.
Broken or weak suction or delivery
valve spring
Check and replace if necessary.
Foreign matter in valves Check and clean if necessary.
Worn bearings Check and replace if necessary.
Excessive temperature of water Reduce to below 160o F.
PRESENCE OF WATER IN
PUMP OIL
Oil seal worn Check and replace if necessary.
High humidity in air Check and replace if necessary.
Piston packing worn Check and replace if necessary.
WATER DRIPPING FROM
UNDER PUMP
Piston packing worn Check and replace if necessary.
O-ring plunger retainer worn Check and replace if necessary.
WATER DRIPPING FROM
PUMP PROTECTOR
Water supply pressure too high (over
90 PSI)
Lower water supply pressure using a regulator.
Spray gun is in the off position for over
5 minutes
Turn machine off if not in use for over 5 minutes.
OIL DRIPPING Oil seal worn Check and replace if necessary.
EXCESSIVE VIBRATION IN
HIGH PRESSURE HOSE
Irregular functioning of the pump
valves
Check and replace if necessary.
MOTOR DOES NOT START
WHEN SWITCHED ON
Plug not well connected or lack of
power supply
Check plug, cable and switch.
WHEN SWITCHING ON THE
MACHINE, MOTOR HUMS
BUT DOES NOT RUN
Main voltage is insufficient, lower than
the minimum required
Check to make sure main power supply is adequate.
The pump is stuck or frozen Check by turning the motor manually.
MOTOR STOPS Tripped thermal overload due to
overheating
Check that main voltage corresponds to the
specifications for the DE. Wait a few minutes before
turning on the machine again by resetting the GFCI
cord.

DE SERIES PRESSURE WASHER OPERATOR’S MANUAL
13
Shark DE •Rev. 10/02
PREVENTATIVE MAINTENANCE
This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the
owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative mainte-
nance procedures will assist in preserving the performance of your equipment. Contact your Shark dealer for main-
tenance. Regular preventative maintenance will add many hours to the life of your pressure washer. Perform mainte-
nance more often under severe conditions.
OIL CHANGE RECORD
Check pump oil and engine oil level before first use of your new pressure washer.
Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
MAINTENANCE SCHEDULE
Pump Oil
Inspect Daily inspect the oil level
Change After first 50 hours, then every 500 hours or annually
Replace High Pressure Nozzle Every 6 months
Replace Quick Connects Annually
Clean Water Screen/Filter Weekly
Replace HP Hose Annually if there is any sign of wear
Grease Motor Every 10,000 hours

DE SERIES PRESSURE WASHER
WARRANTY
Shark DE •Rev. 10/02
SHARK LIMITED NEW PRODUCT WARRANTY
PRESSURE WASHERS
WHAT THIS WARRANTY COVERS
All SHARK PRESSURE WASHERS are warranted by SHARK to the original purchaser to be free from defects in materials and
workmanship under normal use, for the periods specified below.This Limited Warranty is subject to the exclusions shown below,
is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced under this
warranty will assume the remainder of the part’s warranty period. This warranty applies to the original purchaser and is not
transferable.
LIMITED LIFETIME PARTS WARRANTY:
Components manufactured by SHARK, such as frames, handles, coil wraps, float tanks, and belt guards. Forged brass pump
manifold. All heating coils will have a three year warranty. Internal components on the oil-end of all pressure washer pumps will
have a seven year warranty.
ONE YEAR PARTS WARRANTY:
All other components, excluding normal wear items as described below, will be warranted for one year on parts. Warranty on
these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty.
WARRANTY PROVIDED BY OTHER MANUFACTURERS:
Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manufac-
turers’local authorized service centers. SHARK cannot provide warranty on these items.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover the following items:
1. Normal wear items, such as nozzles, guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings,
packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protectors.
2. Damage or malfunctions resulting from accidents, abuse, modifications, alterations, incorrect installation, improper
servicing, failure to follow manufacturer’s maintenance instructions, or use of the equipment beyond its stated usage
specifications as contained in the operator’s manual.
3. Damage due to freezing, chemical deterioration, scale buildup, rust, corrosion, or thermal expansion.
4. Damage to components from fluctuations in electrical or water supply.
5. Normal maintenance service, including adjustments, fuel system cleaning, and clearing of obstructions.
6. Transportation to service center, shop labor charges, field labor charges, or freight damage.
WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE
While not required for warranty service, we request that you register your SHARK pressure washer by returning the completed
registration card. In order to obtain warranty service on items, you must return the product to an Authorized SHARK Dealer,
freight prepaid, with proof of purchase, within the applicable warranty period. If the product is permanently installed, you must
notify your Authorized SHARK Dealer of the defect. The Authorized Dealer will file a claim, which must subsequently verify the
defect. In most cases, the part must be returned to SHARK freight prepaid with the claim. For warranty service on components
warranted by other manufacturers, the Authorized Dealer can help you obtain warranty service through these manufacturers’
local authorized service centers. If you are unable to resolve the warranty claim satisfactorily, write to SHARK at 4275 N.W.
Pacific Rim Blvd., Camas, WA 98607, ATTN: Warranty Dept., detailing the nature of the defect, the name of the Authorized
Dealer, and a copy of the purchase invoice.
LIMITATION OF LIABILITY
SHARK’S liability for special, incidental, or consequential damages is expressly disclaimed. In no event shall SHARK’S liability
exceed the purchase price of the product in question. SHARK makes every effort to ensure that all illustrations and specifica-
tions are correct, however, these do not imply a warranty that the product is merchantable or fit for a particular purpose, or that
the product will actually conform to the illustrations and specifications. THE WARRANTY CONTAINED HEREIN IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A PAR-
TICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representation or
promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure
that the installation and use of SHARK products conforms to local codes. While SHARK attempts to assure that its products
meet national codes, it cannot be responsible for how the customer chooses to use or install the product.
SHARK PRESSURE WASHERS
4275 N.W. Pacific Rim Blvd. •Camas, WA 98607 •USA •1-800-771-1881

4275 N.W. Pacific Rim Blvd. •Camas, WA 98607 •1-800-771-1881
Form #97-6127 •Revised 10/02 •Printed in U.S.A.