Shark HE Series Service manual

MODEL: HE
OPERATING INSTRUCTION
AND PARTS MANUAL
For technical assistance or the SHARK dealer nearest you, call 1-800-771-1881
or visit our website at www.shark-pw.com
■HE-2010 ■ HE-2015
97-717

CONTENTS
2
ModelNumber______________________________
Serial Number ______________________________
Date of Purchase ____________________________
The model and serial numbers will be found on a decal attached to
the pressure washer.You should record both serial number and
date of purchase and keep in a safe place for future reference.
96-723, 97-715, 97-716, 97-717 • REV. 2/04
Important Safety Information................................................................3-4
ComponentIdentification ........................................................................ 5
Assembly Instructions.............................................................................6
Operating Instructions.............................................................................7
Applying Detergent and General OperatingTechniques..........................8
Shut Down and Clean-Up .......................................................................9
Storage ...................................................................................................9
Troubleshooting .................................................................................... 10
Preventative Maintenance..................................................................... 11
Oil Change Record ............................................................................... 11
ExplodedView ...................................................................................... 12
ExplodedView Parts List ...................................................................... 13
Hose and Spray Gun Assembly ............................................................ 14
Downstream Injector............................................................................. 14
Warranty

96-723, 97-715, 97-716, 97-717 • REV. 2/04 3
PRESSURE WASHER OPERATOR’S MANUAL
INTRODUCTION
Thank you for purchasing a Pressure Washer.
Allinformationinthismanualisbasedon thelatestprod-
uct information available at the time of printing.
We reserve the right to makechanges at anytimewith-
out incurring any obligation.
This machine was designed for maximum
use of 1 hour a day, 5 days a week.
Owner/User Responsibility:
The owner and/or user must have an understanding of
themanufacturer’s operating instructions and warnings
before using this pressure washer.Warninginformation
should be emphasized and understood.If the operator
is not fluent in English, the manufacturer’s instructions
and warnings shall be read to and discussed with the
operator in the operator’s native language by the pur-
chaser/owner, making sure that the operator compre-
hends its contents.
Owner and/or user must study and maintain for future
reference the manufacturers’instructions.
This manual should be considered a permanent
part of the machine and should remain with it if
machine is resold.
When ordering parts, please specify model and
serial number.
IMPORTANT SAFETY
INFORMATION
WARNING:To reduce the risk of
injury, read operating instruc-
tions carefully before using.
1. Readtheowner'smanualthor-
oughly. Failure to follow in-
structions could cause mal-
function of the machine and
result in death, serious bodily
injury and/or property dam-
age.
2. Knowhowtostopthe machine andbleedpressures
quickly.Be thoroughly familiar with the controls.
3. Stay alert – watch what your are doing.
4. Allinstallationsmustcomplywithlocalcodes.Con-
tactyourelectrician,plumber,utilitycompanyor the
sellingdistributorforspecificdetails.Tocomplywith
theNationalElectrical code (NFPA70)andprovide
additionalprotectionfromrisk ofelectric shock,this
pressure washer is equipped with a UL approved
ground fault circuit interrupter (GFCI) power cord.
WARNING: Flammable liquids
can create fumes which can ig-
nite,causing propertydamage or
severe injury.Do not spray flam-
mable liquids.
5. Riskofexplosion-donotspray
flammableliquidsoroperatein
anexplosivelocation.Operate
onlywhereopenflameor torch
is permitted.
WARNING: Keep water spray
away from electrical wiring or fa-
tal electric shock may result.
6. WARNING: To protect the
operator from electrical
shock,the machine must be
electrically grounded. It is
the responsibility of the
owner to connect this ma-
chine to a UL grounded
receptacle of proper voltage and amperage rat-
ings. Do not spray water on or near electrical
components. Do not touch machine with wet
hands or while standing in water. Always dis-
connect power before servicing.
7. Grip cleaning wand securely with both hands be-
fore starting the pressure washer.Failure to do this
could result in injury from a whipping wand.
WARNING: Equipment can pro-
duce a high pressure stream of
fluid that can pierce skin and its
underlyingtissues,leading to se-
rious injury and possible ampu-
tation.
8. High pressure developed by
thesemachines willcauseper-
sonal injury or equipment
damage. Use caution when operating. Do not di-
rectdischargestreamatpeople,orsevereinjury or
death will result.
9. Never make adjustments on machine while in op-
eration.
WARNING: High pressure can
cause paint chips or other par-
ticles to become airborne and fly
at high speeds.
10. Eye safety devices, foot pro-
tectionandprotectiveclothing
must be worn when using this
equipment.
11. Machines with spray gun should not be operated
withthetrigger in the off position forextensive peri-
odsoftimeasthismay causedamagetothepump.
12. The best insurance against an accident is precau-
tion and knowledge of the machine.
WARNING
READ OPERATOR’S
MANUALTHOROUGHLY
PRIORTO USE.
WARNING
KEEP WATER
SPRAY AWAY FROM
ELECTRICALWIRING.
WARNING
HIGH PRESSURE
STREAM CAN
PIERCE SKIN AND
TISSUES.
WARNING
RISK OF EXPLOSION:
DO NOT SPRAY
FLAMMABLE LIQUIDS.
WARNING
USE PROTECTIVE
CLOTHINGWHEN
OPERATING.

96-723, 97-715, 97-716, 97-717 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
4
13. We will not be liable for any changes made to our
standard machines, or any components not pur-
chased from us.
14. Be certain all quick coupler fittings are secured be-
fore using pressure washer.
15. Never run pump dry or leave spray gun closed
longer than 5 minutes.
16. To reduce theriskofinjury, close supervisionisnec-
essary when a machine is used near children. Do
not allow children to operate the pressure washer.
This machine must be attended during opera-
tion.
17. Protect from freezing.
18. Whenthemachineis working, donotcoverorplace
in a closed space where ventilation is insufficient.

96-723, 97-715, 97-716, 97-717 • REV. 2/04 5
PRESSURE WASHER OPERATOR’S MANUAL
COMPONENT IDENTIFICATION
Plug
(120V)
Power
Supply
Pressure Nozzle
Brass Soap
Nozzle
Water
Faucet
Water Supply
Hose
(not included)
Trigger
High
Pressure
Hose
Detergent Bucket
(not included)
Detergent
Pick-up Tube
Oil Dip
Stick
Spray
Gun
Quick Coupler
Nozzle
Quick
Coupler
Inlet
Connector
Discharge
Nipple
GFCI
Electric
Motor
Wand
Detergent Injector - Allows you to siphon and mix de-
tergents.
High Pressure Hose -Connectoneend to waterpump
discharge nipple and the other end to spray gun.
Nozzle Quick Coupler -
Pump - Develops high pressure.
Spray Gun - Controls the application of water and de-
tergent onto cleaning surface with trigger device. In-
cludes safety latch.
Swivel Connector - Allows free range of movement to
avoid coiling hoses.
Wand - Must be connected to the spray gun.
Note:If trigger on spray gun is released for more
than 2 minutes, water will leak from valve. Warm
waterwilldischarge frompump protectoronto floor.
This system prevents internal pump damage.
Swivel
Connector

96-723, 97-715, 97-716, 97-717 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
6
ASSEMBLY INSTRUCTIONS
STEP 1: Attach the high
pressure hose to the spray
gun using teflon tape on
hose threads.
STEP 4: Release the coupler col-
lar and push the nozzle until the
collar clicks. Pull the nozzle to
make sure it is seated properly.
STEP6:Connect thehighpressure
hose to the pump discharge fitting.
Push coupler collar forward until
secure.
STEP 2: Attachnozzleextension to spray
gun/wand. Tighten both by hand. STEP 3: Pullthespring-loadedcol- lar of the wand coupler back to in-
sertyourchoice ofpressurenozzle.
STEP 7: Connect garden hose to
the cold water source.
STEP 8: Connect the garden hose to pump water inlet. In-
spect inlets. CAUTION:Do not run the pump without wa-
ter or pump damage will result.
Safety
Latch
Spray
Gun
High Pressure
Hose
Nozzle
Extension
Spray Gun/
Wand
Wand
Coupler
Pressure
Nozzle
Pressure
Nozzle Wand
Coupler
Wand
Collar
Pump
Discharge
Fitting
High
Pressure
Hose
Cold
Water
Source
Garden
Hose
Pump
Water Inlet
Garden
Hose
Coupler Collar
STEP 5: Remove shipping cap and
install oil dipstick. Check pump oil
level by using dipstick. Use 30 wt.
non detergent oil.
Dipstick

96-723, 97-715, 97-716, 97-717 • REV. 2/04 7
PRESSURE WASHER OPERATOR’S MANUAL
OPERATING INSTRUCTIONS
STEP1: Connectgardenhose tothe
coldwatersource and turn wateron
completely.Never use hot water.
STEP 2:Trigger the spray gun to
eliminate trapped air then wait for
a steady flow of water to emerge
from the spray nozzle.
Cold
Water
Source
Garden
Hose
WARNING! Never replace
nozzles without engaging the
safety latch on the spray gun trig-
ger.
Thetwocolor-codedquickconnectnozzlesare
easily accessible when placed in the conve-
nient rubber nozzle holder, which is provided
on the front of the machine.
NOTE:Torinse,selecttheyellow.Toapplyde-
tergent select the black nozzle.
NOZZLES
Safety
Latch
STEP 4: Connect to ap-
propriate power supply.
STEP 4: Turn machine on by flipping
switch at rear of motor.

96-723, 97-715, 97-716, 97-717 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
8
WARNING: Some detergents
may be harmful if inhaled or in-
gested, causing severe nausea,
fainting or poisoning.The harm-
fulelementsmay cause property
damage or severe injury.
STEP 1: Use detergent designed
specifically for pressure washers.
Household detergents could dam-
age the pump. Prepare detergent
solution as required by the manu-
facturer. Fill a container with pres-
sure washer detergent. Place the
filter end of detergent suction tube
into the detergent container.
STEP 2: Applysafetylatchtosprayguntrigger. Secure
black detergent nozzle into quick coupler. NOTE: De-
tergent cannot be applied using theYellow nozzle.
STEP 3: With the engine run-
ning,pulltriggertooperatema-
chine. Liquid detergent is
drawn into the machine and
mixed with water.Apply deter-
gent to work area. Do not al-
lowdetergenttodryonsurface.
IMPORTANT:You must flush the detergent injection
system after each use by placing the suction tube
into a bucket of clean water, then run the pressure
washer in low pressure for 1-2 minutes.
THERMAL PUMP PROTECTION
If you run the engine on your pressure washer for 3-5
minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach high tempera-
tures. When the water reaches this temperature, the
pump protector engages and cools the pump by dis-
charging the warm water onto the ground.This thermal
device prevents internal damage to the pump.
CLEANINGTIPS
Pre-rinse cleaning surfacewith freshwater.Placedetergent
suction tube directly into cleaning solution and apply to sur-
face at low pressure (for best results, limit your work area to
sections approximately 6 feet square and always apply de-
tergent from bottom to top). Allow detergent to remain on
surface 1-3 minutes. Do not allow detergent to dry on sur-
face. If surface appears to be drying, simply wet down sur-
face with fresh water. If needed, use brush to remove stub-
born dirt. Rinse at high pressure from top to bottom in an
even sweeping motion keeping the spray nozzle approxi-
mately1footfromcleaningsurface.Useoverlappingstrokes
as you clean and rinse any surface.For best surface clean-
ing action spray at a slight angle.
Recommendations:
• Before cleaning any surface, an inconspicuous
area should be cleaned to test spray pattern and
distance for maximum cleaning results.
• If painted surfaces are peeling or chipping, use
extreme caution aspressurewashermayremove
the loose paint from the surface.
• Keep the spray nozzle a safe distance from the
surface you plan to clean. High pressure wash a
small area, then check the surface for damage. If
no damage is found, continue to pressure wash-
ing.
CAUTION - Never use:
• Bleach, chlorine products and other corrosive
chemicals
• Liquids containing solvents (i.e., paint thinners,
gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the machine and will dam-
age the surface being cleaned.
RINSING
• It will take a few seconds for the detergent to clear.
Applysafety latchtospray gun.Remove blacksoap
nozzlefromthequickcoupler.Select and install the
desired high pressure nozzle.NOTE: You can also
stopdetergentfromflowingby simply removingde-
tergent siphon tube from bottle.
WARNING
DETERGENTS AND GENERAL OPERATINGTECHNIQUES

96-723, 97-715, 97-716, 97-717 • REV. 2/04 9
PRESSURE WASHER OPERATOR’S MANUAL
SHUTTING DOWN AND CLEAN-UP
STEP 1: Remove de-
tergent suction tube
from container and in-
sert into one gallon of
fresh water. Slide
nozzle forward for low
pressureortoconnect
black detergent
nozzle.Pull trigger on
spray gun and siphon
water for one minute.
STEP 2: Turn off machine by
flipping switch on rear of mo-
tor.
STEP 5: Disconnect the garden
hose from the water inlet on the
machine.
STEP 6: Disconnect the high
pressure hose from high pres-
sure outlet.
STEP 7: Engage
the spray gun
safety lock.
STEP 4: Press trigger
to release water pres-
sure.
Pump
Water
Inlet
High
Pressure
Outlet Safety
Latch
STORAGE
CAUTION
Pump Storage
CAUTION: Always store your pres-
sure washer in a location where the
temperature will not fall below 32° F
(0° C).The pump in this machine is
susceptible to permanent damage if
frozen.
FREEZEDAMAGE ISNOTCOVERED
BYWARRANTY.
If you must store your pressure washer in a location
where the temperature is below 32° F, you can mini-
mize the chance of damage to your machine by drain-
ing your machine as follows:
1. Stop the pressure washer and detach supply hose
andhigh pressure hose.Squeezethe trigger ofthe
spray gun to drain all water from the wand and
hose.
2. Restartpressurewasher and let it runbriefly(about
5 seconds) until water no longer discharges from
the high pressure outlet.
STEP 3: Turn off water supply.

96-723, 97-715, 97-716, 97-717 • REV. 2/04
PRESSURE WASHER Troubleshooting Guide
10
PROBLEM POSSIBLE CAUSE SOLUTION
PUMP RUNNING
NORMALLY BUT
PRESSURE LOW ON
INSTALLATION
Pump sucking air Check water supply and possibility of air seepage.
Check valves sticking Check and clean or replace if necessary.
Unloader valve seat faulty Check and replace if necessary.
Nozzle incorrectly sized Check and replace if necessary.
Worn piston packing Check and replace if necessary.
FLUCTUATING
PRESSURE Valves worn Check and replace if necessary.
Blockage in valve Check and replace if necessary.
Pump sucking air Check water supply connections.
Worn piston packing Check and replace if necessary.
Insufficient water Check filter and hose for breakage.
PRESSURE LOW AFTER
PERIOD OF NORMAL USE Nozzle worn Check and replace if necessary.
Suction or delivery valves worn Check and replace if necessary.
Suction or delivery lines blocked Check and clean if necessary.
Unloader valve seat worn Check and replace if necessary.
Worn piston package Check and replace if necessary.
Water temperature excessive Reduce to below 140oF.
PUMP NOISY Air in suction line Check water supply and connections on suction line.
Broken or weak suction or delivery valve
spring. Check and replace if necessary.
Foreign matter in valves Check and clean if necessary.
Worn bearings Check and replace if necessary.
Water temperature excessive Reduce to below 160oF.
PRESENCE OF WATER IN
PUMP OIL Oil seal worn Check and replace if necessary.
High humidity in air Check and replace if necessary.
Piston packing worn Check and replace if necessary.
WATER DRIPPING FROM
UNDER PUMP Piston packing worn Check and replace if necessary.
O-ring plunger retainer worn Check and replace if necessary.
WATER DRIPPING FROM
PUMP PROTECTOR Water supply pressure too high
(over 90 psi) Lower water supply pressure using regulator.
Spray gun is in the off position for over 5
minutes Turn machine off if not in use for over 5 minutes.
OIL DRIPPING Oil seal worn Check and replace if necessary.
EXCESSIVE VIBRATION IN
HIGH PRESSURE HOSE Irregular functioning of the pump valves Check and replace if necessary.
MOTOR DOES NOT START
WHEN SWITCHED ON Plug not well connected or lack of power
supply Check plug, cable and switch.
WHEN SWITCHING ON
THE MACHINE, MOTOR
HUMS BUT DOES NOT
RUN
Main voltage is insufficient, lower than the
minimum required. Check to make sure main power supply is adequate.
The pump is stuck or frozen Check by turning the motor manually.
MOTOR STOPS Tripped thermal overload due to
overheating Check that main voltage corresponds to specifications for the machine. Wait a few minutes before turning on
the machine again by resetting the GFCI on the cord.
TROUBLESHOOTING

96-723, 97-715, 97-716, 97-717 • REV. 2/04 11
PRESSURE WASHER OPERATOR’S MANUAL
Thispressurewasherwas produced with the best availablematerialsandqualitycraftsmanship.However, youas
the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative
maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for
maintenance.Regularpreventativemaintenance will add manyhourstothe lifeofyour pressure washer.Perform
maintenance more often under severe conditions.
Pump Oil Inspect Daily inspect the oil level
Change After first 50 hours, then every 500 hours or annually
Replace High Pressure Nozzle Every 6 months
Replace Quick Connects Anually
Clean Water Screen/Filter Weekly
Replace HP Hose Anually if there is any sign of wear
Grease Motor Every 10,000 hours or annually
General InspectionInspect the motor at regular intervals, approximately every 500 hours of operation,
or every 3 months, whichever occurs first.Keep the motor clean and the ventilation
openings clear.The following steps should be performed at each inspection:
WARNING: Do not touch electrical connections before you first ensure that power
hasbeendisconnected.Electrical shockcancauseserious or fatalinjury.Onlyquali-
fied personnel should attempt the installation, operation and maintenance of this
equipment.
1. Check that the motor is clean.Check that the interior and exterior of the motor
is free of dirt, oil, grease, water, etc.Oily vapor, paper pulp, textile lint, etc.can
accumulate and block motor ventilation.If the motor is not properly ventilated
overheating can occur and cause early motor failure.
2. Check all electrical connectors to be sure that they are tight.
Lubrication & Bearings Bearing grease will lose its lubricating ability over time, not suddenly.The lubricating
ability of a grease (over time) depends primarily on the type of grease, the size of the
bearing, the speed at which the bearing operates and the severity of the operating
conditions.Good resultscan beobtained if thefollowingrecommendations are usedin
your maintenance program.
Type of Grease A high grade ball or roller bearing grease should be used. Recommended greases
standard service conditions are: Shell Dolium R (Factory installed) or Chevron SRI
OIL CHANGE RECORD
Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
PREVENTATIVE MAINTENANCE

96-723, 97-715, 97-716, 97-717 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
12
EXPLODED VIEW
23
13
14
12
11
1
25
17
15
14
21
14
21
30 29
35
36
26
28
25
33
34
20
19
18
32 31
16
10
9
8
7
1
24 2
7
3
4
5
6
8
27
22
34
14
13 14
13
Models 201406D, 2015070
Models
201006D,
201007D,
2-11026D

96-723, 97-715, 97-716, 97-717 • REV. 2/04 13
PRESSURE WASHER OPERATOR’S MANUAL
EXPLODED VIEW PARTS LIST
ITEM PART # DESCRIPTION QTY
1 6-01062 GFCI, 120V, 15 Amp w/36' 12-3
Cord (201006D, 201007D,
211026D) 1
6-01060 GFCI, 120V 20 Amp w/36' 12-3
Cord (201406D, 201507D) 1
2 6-03911 Lid, Plastic Carlon
(201406D, 201507D) 1
3 6-020204 Switch, 2 Pos. 120V-600V
(201406D, 201507D) 1
4 6-03910 Box, Plastic Carlon
(201406D, 201507D) 1
11-1042 ▲Label, Ground 1
5 6-051595 Strain Relief, STRT, LQ Tite
Large (201406D, 201507D) 1
6-05172 ▲Locknut, 3/4" 1
6 6-0104 Cord, Service, SOWA, 12/3
(201406D, 201507D) 2 ft.
7 90-1991 Screw, 10/32" x 1/2" BHSOC
(201406D, 201507D) 6
8 90-017 Nut, 10/32" Keps
(201406D, 201507D) 9
9 90-100030 Screw, 10-32" x 3/4" RH, SL,
BLK (201406D, 201507D) 1
10 95-07111118 Switch Box BRKT
(201406D, 201507D) 1
11 5-1046 Motor, 1.5 HP, 1 PH, 3450 RPM,
C-Face (201006D, 2-11026D,
201007D) 1
6-05152 ▲Strain Relief, STRT, LQ TITE 3
(201006D, 201007D) 1
6-05181A ▲Locknut, 1/2" (201006D,
201007D) 1
5-1047 Motor, 2 HP, 1 PH, 3450 RPM,
(201406D, 201407D) 1
6-0517 ▲Strain Relief, 3/4"
(201406D, 201407D) 1
12 6-02049 Switch, Toggle, Assy (201006D,
201007D, 2-11026D) 1
13 90-2001 Nut, 5/16" ESNA, NC 8
14 90-4001 Washer, 5/16" Flat SAE 12
15 11-0350F Label, French Warning 1
16 11-0314 Label, Instr. (TE Models) 1
11-0311 Label, Instr. (HE Models) 1
10-99073 Label, Instr. (ZE Models) 1
11-0325 Label, Instr. (ET Models) 1
17 95-07200126 Handle Assy, Red (TE, HE,
ET Models) 1
95-07102116 Handle Assy, Black (Model
ZE) 1
18 4-16540 Nozzle, Compl. QCEM-6540
w/Blk Nylon (Soap Nozzle) 1
ITEM PART # DESCRIPTION QTY
19 4-12804015 Nozzle, SAQCMEG 1504
Yellow (201006D, 201007D,
2-11026D) 1
4-12803015 Nozzle, SAQCMEG 1503 Yellow
(201406D, 201507D) 1
20 2-0103 Grommet, Rubber, Nozzle
Holder 2
21 90-1006 Bolt, 5/16" x 3/4" NC 4
22 10-08021 Label, Disconnect Power 1
23 10-08018 Label, Warning, Service
Cord 1
24 6-05154 Strain Relief 90° (201406D)1
6-05181 ▲Locknut, 1/2" Conduit
(201406D) 1
25 2-01023 Mount, Vibration, 5/16”-18 x
9/16” Stud, 30 Duro 4
26 10-08016 Label, Intended For Indoor
Use 1
27 10-9999 Label, Clear Lexan,
2-1/4" x 4-1/2" 1
28 2-300816 Pump Protector, 3/8" PTP 1
29 2-2006 Nipple, 3/8" x 3/8" NPT ST
Female 1
30 2-10943 Swivel, 3/8" MP x 3/4" (201001D,
201501D, 301001D) 1
31 90-4002 Washer, 3/8" Flat SAE 4
32 90-1016 Bolt, 3/8" x 1", NC 4
33 5-2107 Pump, Comet AXD2020E
(201006D, 201406D,
2-11026D) 1
5-1618 Pump, Legacy, WMH2521
(201007D, 201507D) 1
34 2-9040 Clamp, Hose UNI .46 - .54 2
35 4-02080000 Hose, 1/4” x 1/2” Clear
Vinyl 4 ft.
36 2-1904 Strainer, 1/4” Barb 1

96-723, 97-715, 97-716, 97-717 • REV. 2/04
OPERATOR’S MANUAL
PRESSURE WASHER
14
HOSE & SPRAY GUN ASSEMBLY
HOSE & SPRAY GUN ASSEMBLY PARTS LIST
ITEM PART NO. DESCRIPTION QTY
1 2-2002 Coupler, 3/8" Female 1
2-0121 ▲Quick Coupler O-Ring 1
2 4-0203030C Hose, 30' x 3/8" w/Coupler (ET,
ZE Models) 1
4-020930BSC Hose, 30’ x 3/8” w/Coupler (HE
TE Models) 1
3 4-011137 Spray Gun, Shut-Off (ET, ZE
Models) 1
4-01246 Spray Gun, Shut-Off (HE, TE
Models) 1
4 4-011106 Wand, Straight (ET, ZE
Models) 1
4-0110531 Wand, SS 15.5” (TE, HE
Models) 1
5
3
1
2
6
7
Pressure Nozzle
Brass Soap
Nozzle
4
ITEM PART NO. DESCRIPTION QTY
5 2-2000 Coupler, 1/4” Female 1
2-0119 Quick Coupler O-Ring 1
6 4-12803015 Nozzle, 3.0 15° Yellow
(201406D, 201507D
2-11026D) 1
Nozzle, 4.0 15°Yellow (201006D,
201007D) 1
7 4-16540 Nozzle, Brass Soap 1
▲Not Shown

HE SERIES PRESSUREWASHER
WARRANTY
SHARK LIMITED NEW PRODUCTWARRANTY
PRESSURE WASHERS
WHAT THIS WARRANTY COVERS
All SHARK PRESSURE WASHERS are warranted by SHARK to the original purchaser to be free from defects in materials and
workmanship under normal use, for the periods specified below.This Limited Warranty is subject to the exclusions shown below,
is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced under this
warranty will assume the remainder of the part’s warranty period. This warranty applies to the original purchaser and is not
transferable. LIMITED LIFETIME PARTS WARRANTY:
Components manufactured by SHARK, such as frames, handles, coil wraps, float tanks, and belt guards. Forged brass pump
manifold.All heating coils will have a three year warranty.Internal components on the oil-end of all pressure washer pumps will
have a seven year warranty. ONE YEAR PARTS WARRANTY:
All other components, excluding normal wear items as described below, will be warranted for one year on parts. Warranty on
these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty.
WARRANTY PROVIDED BY OTHER MANUFACTURERS:
Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manufac-
turers’ local authorized service centers. SHARK cannot provide warranty on these items.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover the following items:
1. Normal wear items, such as nozzles, guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings,
packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protectors.
2. Damage or malfunctions resulting from accidents, abuse, modifications, alterations, incorrect installation, improper
servicing, failure to follow manufacturer’s maintenance instructions, or use of the equipment beyond its stated usage
specifications as contained in the operator’s manual.
3. Damage due to freezing, chemical deterioration, scale buildup, rust, corrosion, or thermal expansion.
4. Damage to components from fluctuations in electrical or water supply.
5. Normal maintenance service, including adjustments, fuel system cleaning, and clearing of obstructions.
6. Transportation to service center, shop labor charges, field labor charges, or freight damage.
WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE
While not required for warranty service, we request that you register your SHARK pressure washer by returning the completed
registration card. In order to obtain warranty service on items, you must return the product to an Authorized SHARK Dealer,
freight prepaid, with proof of purchase, within the applicable warranty period. If the product is permanently installed, you must
notify your Authorized SHARK Dealer of the defect.The Authorized Dealer will file a claim, which must subsequently verify the
defect.In most cases, the part must be returned to SHARK freight prepaid with the claim. For warranty service on components
warranted by other manufacturers, the Authorized Dealer can help you obtain warranty service through these manufacturers’
local authorized service centers. LIMITATION OF LIABILITY
SHARK’S liability for special, incidental, or consequential damages is expressly disclaimed. In no event shall SHARK’S liability
exceed the purchase price of the product in question. SHARK makes every effort to ensure that all illustrations and specifica-
tions are correct, however, these do not imply a warranty that the product is merchantable or fit for a particular purpose, or that
the product will actually conform to the illustrations and specifications.THEWARRANTY CONTAINED HEREIN IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A PAR-
TICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representation or
promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way.It is the buyer’s responsibility to ensure
that the installation and use of SHARK products conforms to local codes. While SHARK attempts to assure that its products
meet national codes, it cannot be responsible for how the customer chooses to use or install the product.
SHARK PRESSURE WASHERS
1-360-833-9100 • 1-800-771-1881 • www.shark-pw.com
SHARK HE • 97-717 • REV. 2/04
PRESSURE WASHER WARRANTY

Form#97-717 • Revised2/04 • PrintedinU.S.A.