Shark GS500 User manual

GS500 series
User’s Guide
garment care system

21-800-79-7398
WARNING:
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY:
1. Use the system only for its intended use.
2. DO NOT use outdoors.
3. DO NOT leave the appliance unattended when
plugged in. Always unplug the power cord from
the electrical outlet when not in use and before
servicing.
4. DO NOT allow the appliance to be used by
children. Close attention is necessary when used
near children, pets, or plants.
5. Use only as dscribed in this manual.
6. Use only manufacturer’s recommended
accessories.
7. DO NOT use with damaged cord or plug.
8. DO NOT USE the appliance is not working, has
been dropped, dropped into water, damaged,
left outdoors, or if it is leaking.
9. NO SERVICEABLE PARTS. Incorrect re-
assembly or repair can cause a risk of electrical
shock or injury to persons when the appiance is
used. Contact Customer Service.
10. To protect against a risk of electric shock, DO
NOT immerse the garment steamer into water or
any other liquids.
11. DO NOT handle plug or garment steamer with
wet hands or operate appliance without shoes.
12. DO NOT pull or carry by power cord, use power
cord as a handle, close a door on the power
cord, or pull the power cord around sharp
corners or edges. Keep power cord away from
heated surfaces.
13. ALWAYS unplug the power cord from the
electrical outlet when filling or emptying the
water tank and when not in use.
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK®
PRESS & REFRESH™GARMENT
CARE SYSTEM, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE
USING YOUR PRESS & REFRESH™
GARMENT CARE SYSTEM.
DANGER OF SCALDING
Please use caution when using the
garment steamer. The Wrinkle Eraser™
pressing bar and the steam emitted are very
hot. The Wrinkle Eraser™is not controlled by
the steam trigger and is hot as long as the
unit is turned on and for 30 minutes after the
unit has been turned off.
IMPORTANT:
This appliance is not intended for use by
persons with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for
their safety.
Children shall not use or play with this
appliance. Close supervision is necessary to
keep appliance and its cord out of reach of
children during use and cooling.

3
www.sharkninjamanuals.com
14. NEVER attempt to fill this unit under a water
faucet. Always use the filling flask that is
provided.
15. DO NOT unplug by pulling on the power cord.
To unplug, grasp the plug not the power cord.
Do not use extension cords or outlets with
inadequate currect carrying capacity.
16. DO NOT put any objects into openings. Do not
use with any opening blocked.
17. This appliance and the accessories become hot
during use and surfaces may also become hot.
Exercise care when changing accessories and
follow removal and changing instructions as
outlined in the manual. Do not change frames
while the unit is turned on. Turn the unit off,
wait for the Wrinkle Eraser™to cool, and then
change frames.
18. The garment steamer can be used in a vertical
or horizontal motion. NEVER hold the steam
head down while at rest or tilt it in a backward
position as this may result in discharge. When
using the appliance, it must be rested on a
stable surface.
19. DO NOT use on leather, suede, vinyl, plastic or
other delicate steam sensitive materials. Always
determine the colorfastness of any fabric before
using the garment steamer by testing it on a
small portion of the garment’s underside.
20. NEVER attempt to steam clothing while it is
being worn.
21. DO NOT add cleaning solutions, scented
perfumes, oils, or any other chemicals to the
water used in this appliance as this may damage
the unit or make it unsafe for use. If you live in a
hard water area, we recommend using distilled
water in your garment steamer.
22. When in use, NEVER turn the appliance
over or on its side. NEVER DIRECT STEAM
TOWARDS PEOPLE, ANIMALS OR PLANTS.
The steam is very hot and can cause burns.
Burns can occur from touching hot metal parts,
steam, steam bonnets or frames.
23. Use care when you turn a steam appliance
upside down - there may be hot water in the
reservoir.
24. Let the system cool completely before putting
away. Loop cord loosely around the appliance
when storing.
25. When cleaning the garment steamer, unplug the
power cord from the electrical outlet and clean
with a dry or damp cloth. Do not pour water
or use alcohol, benzene or paint thinner on the
unit. :
26. Keep your work area well lit.
27. Store the garment steamer indoors in a cool, dry
place.
28. To avoid circuit overload, do not operate another
appliance on the same socket (circuit) as the
garment steamer.
29. If an extension cord is absolutely necessary, an
extension cord rated a minimum of 15 ampere,
2.08mm2cord should be used. Cords rated for
less amperage may overheat. Care should be
taken to arrange cord so that it cannot be pulled
or tripped over.
30. DO NOT leave your Garment Steamer
unattended when the system is connected to a
power supply/electrical outlet.
31. Always unplug and allow the garment steamer
to cool before removing or changing frames or
bonnets.
32. Make sure that the water tank door is closed
when using the appliance.
SAVE THESE
INSTRUCTIONS

41-800-79-7398
Welcome to the next wave of garment care!
The Press & Refresh™Garment Care System brings your fabrics back to life with fewer trips to the
dry cleaners! For the first time ever professional steam power in a portable unit.
The professional steam deeply penetrates fibers, renews and freshens fabric. The exclusive heated
Wrinkle Eraser™presses for a crisp finish and dries fibers to prevent re-wrinkling.
Extend the life of your garments and go from not quite ready-to-wear to ready-to-wear in one easy step.
The Look Your Best Guide provides step-by-step tips for all of your garment care needs.
Attaching the appropriate
accessory:
The unit comes assembled with a
small steam bonnet attached. The
bonnet must be attached at all
times when the unit is being used.
1Attach the desired frame
2Using both hands, hold the
frame on either side. Attach
the top of the frame to the
unit above the Wrinkle Eraser™
into the notch. Next, secure
the pointed end of the frame
around the bottom of the unit
and snap into place. (Fig. 1)
The seam of the frame must
line up against the seam of the
unit for proper use.
3To remove the frame, gently
pull on the pointed end and lift
the frame off the unit.
Fig. 1
TIP: Wipe away condensation
from the steam guard on the
bottom of the frame after
extended use.
FRAME/ACCESSORY
Bristle Brush Frame
Upholstery/Delicate
Fabric Frame & Delicate Steam Bonnet
Upholstery/Delicate
Fabric Frame & Upholstery Steam Bonnet
Small Steam Bonnet

5
www.sharkninjamanuals.com
Helpful Tips on using the
Vertical Press Pad and VELCRO®
Clips:
1For the first time ever, the
vertical press pad eliminates the
need for an ironing board. It is
designed to fit on any size door,
and can remain setup for your
convenience. The VELCRO®clips
are used to position & stretch
the garment for quick steaming
with better results to complete
the garment care system .
(Fig. 2)
2To make pressing easier, the
vertical press pad has two hooks
on either end to hang your
garment from for larger pressing
surface.
Fig. 2
USE FOR BENEFITS
Best for: cotton, wool, linen, denim
Best for: bedding, mattress, curtains,
baby bedding, plush toys, high chairs,
car seats, sofa and arm chairs
Best for: lace, velvet, silk, satin,
embelished or delicate garments
Improves steam penetration on heavy
fabrics without leaving water marks
Shaggy material acts like multiple fingers to
pick up dust and deodorise while steaming. It
provides a large pocket of hot steam
Specifically designed to protect delicate
fabric from high heat
The bonnet should always be attached
during any use and with any frame
The specially designed multi layered
honeycomb pad protects fabrics from
water marks and water impurities

61-800-79-7398
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz.
Power: 1580 W
Water Capacity: 200 mL (6.5 fl. oz.)
This manual covers model number:
GS500***** 11
This appliance complies with the WEEE-Directive 2002/96/EC on the disposal of electrical and electronic
equipment (WEEE).
This appliance complies with the European directives for electromagnetic compatibility (EMC) 2004/108/EC and
its revisions, as well as Low Voltage Directive (LVD) 2006/95/EC and its revisions.
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
sources. To return your used device, please use the return and collection systems or contact the
retailer where this product was purchased. They can take this product for environmental safe
recycling.
IPX4

7
www.sharkninjamanuals.com
Contents
Getting Started 8
Assembly of the Vertical Press Pad 9
Using your Press & Refresh™10
Care of your Press & Refresh™13
Troubleshooting Guide 13
Thank you
for purchasing
the Shark®
Press & Refresh™
Garment Care
System.

81-800-79-7398
IMPORTANT: Always check
the fabric care labels for
recommendations. Test the
fabrics for colorfastness in an
inconspicuous place such as
an inside seam. Some articles
of clothing are better steamed
from the underside.
IMPORTANT: When
assembling your garment
steamer, there may be a little
water in the water tank. This
is because we test all our
garment steamers 100%
before you buy them, so you
get a quality Shark®Steam
product.
Getting Started
First things first, you need to
know what’s in the box you
just opened:
aGarment Steamer
b2 Small Steam Bonnet (P117 W)
(one is attached to the unit)
cBristle Brush Frame (1059SO)
dUpholstery/Delicate Fabric
Frame (1060SO)
eUpholstery Steam Bonnet
(P116W )
fDelicate Steam Bonnet (P121W)
The Press & Refresh™Garment Care System provides a complete process for all of your garment
care needs. Save time and money with fewer trips to the dry cleaners and have your garments ready-to-
wear when you want.
The combination of professional steam power and the exclusive heated Wrinkle Eraser™makes it easier
than ever to care for your garments. The Press & Refresh™comes complete with accessories for all
garment care needs. The vertical press pad eliminates the hassle of an ironing board and makes it easy
to steam and press right on the hangers.
Not only great on garments, the Press & Refresh™can be used to refresh fabrics throughout your
home. Now you can easily reduce odors, sanitise fabric and help eliminate dust mites.
The extra long 15 foot power cord makes it easy to navigate around your home.
ag
c
h i
j
k
l
d
e f
gVertical Press Pad
h2 Support Rods (assembled in
the vertical press pad)
iGarment Hook
j8 Heat Protection Panels
(assembled in vertical press
pad)
k3 VELCRO®Clips (1039SO)
lFilling Flask (1057SO)
mAccessory Bag (not shown)
b
VELCRO®is a registered trademark of
Velcro Industries B.V.

9
www.sharkninjamanuals.com
Fig. 3
Assembling the vertical
press pad:
3Insert the garment hook into
the opening at the top of the
vertical press pad. (Fig. 1)
Secure the rod into the garment
hook on either side of the pad
making sure they are inserted
firmly. (Fig. 2) The support rods
come assembled in the pad.
4The Vertical Press Pad comes
asembled with heat protection
panels in the pockets on the
back. These panels protect your
door from heat damage and
should be in place at all times
during use.
Assembly & use instructions:
1Remove contents of the Press &
Refresh™Garment Care System
and lay them out on a flat
surface to see that you have all
the components to complete
the assembly.
2READ ALL INSTRUCTIONS
BEFORE USING YOUR PRESS
& REFRESH™GARMENT CARE
SYSTEM.
IMPORTANT: Always make
sure the garment steamer is
UNPLUGGED from the electrical
outlet when not in use. Never
fill the water reservoir when the
unit is plugged in.
Assembly of the Vertical Press Pad
5Attach the vertical press pad to
any door. With the door open,
loop the straps at the top of the
vertical press pad around the
corner of the door and repeat
on the opposite side. Gently
tug on the pad to make sure
it is secure and shut the door
completely to ensure the pad is
stable for pressing. Be careful
not to close the door on your
fingers. Adjust the straps to the
appropriate height for comfort.
(Fig. 3)
Care instructions:
6Remove the 8 heat protection
panels from the back of the
pad and remove the garment
hook and rods. Machine wash
in warm water with liquid
detergent and lay flat to dry.
Do not use bleach or fabric
softener.
Fig. 2
Fig. 1
The straps can be adjusted
to fit any door using the
buckle to adjust the strap
lengths.

10 1-800-79-7398
unit above the Wrinkle Eraser™
into the notch. Next, secure
the pointed end of the frame
around the bottom of the unit
and snap into place. (Fig. 2)
When using the upholstery/
delicate fabric frame:
NOTE: Remember, DO NOT use
the garment steamer without
the small steam bonnet in place
4Attach the desired bonnet to
the frame, then attach the
frame to the unit. Pull either
side of the bonnet over the top
of the frame and secure the
bottom of the bonnet to the
frame. (Fig. 3) Then attach the
frame to the garment steamer
as described above. (Fig. 4)
Using Your Press & Refresh™
Attaching the accessories:
IMPORTANT: Use caution
when changing the frames
when the unit is hot. The
frames are designed with a
steam guard around the bottom
to provide protection from heat
when placing or removing the
frames.
The small steam bonnet must
be attached at all times during
usage.
The bonnet should only be
removed for washing by hand,
if necessary (see page 13 for
care instructions).
3Choose your desired frame.
Using both hands, hold the
frame on either side. Attach
the top of the frame to the
Filling and refilling the water
reservoir:
1Never fill the garment steamer
while it is plugged into an
electrical outlet.
2Open the water cap and hold
the the garment steamer
horizontally with the Wrinkle
Eraser™parallel to the floor.
Using the filling flask provided
fill the water tank to the Max
Fill line. Be careful not to
overfill. Push the cap back into
place, making sure it closes
firmly. (Fig. 1)
NOTE: The water tank does not
have to be completely full for
the fabric steamer to generate
steam. However, make sure
that the water tank is at least
half way full for optimal results.
Practice makes perfect!
It takes time to master
the garment steaming
techniques.
For best results, tilt the
steamer forward slightly
and press the wrinkle
eraser directly on the
garment.
Fig. 1 Fig. 2
Fig. 4
Fig. 3
The seam on the frame must line up
with the seam on the unit for proper
use and safety. The frame will snap into
place, double check to make sure the
seams are aligned.