Shark LIFT-AWAY PRO STEAM POCKET MOP User manual

1
2
(Click)
Please be sure to read the enclosed Owner’s Guide prior to using your unit.
A S SE M B LY
A Steam Mop Handle
B Steam Mop Body
C Removable Handheld
Steamer
D Intelli-Mop™ Head
E Dirt Grip™ Pad (x2)
F Filling Flask
G Accessory Hose
H Garment Steamer
I Small Above-Floor
Pocket Tool and Pad
B
D
C
WHAT’S INSIDE
FILLING THE WATER TANK
REMOVING THE PAD
F
1. Open the water tank cap.
2 . Use the filling flask and pour
water into the tank Do not overfill.
Replace the cap on the water tank.
S3973_QSG_161122
1. Screw the mop handle into the Steam Mop body
(screwdriver not included)
2 . Slide the Intelli-Mop Head post into the Steam Mop
body. Push until you hear it click securely into place.
E
A
TOUCH-FREE TECHNOLOGY
Lift the mop straight up
by the handle until the
Intelli-Mop Head is hang-
ing straight down. Press
down the release buttons
on the sides of the head
post, and both sides of the
mop head will drop open.
CAUTION: It is recommended that you allow the pads to
cool off before removing them from the accessories to
avoid possible scalding injury.
1. Lift the mop straight
up by the handle until
the Intelli-Mop Head
is hanging straight
down. Center the mop
head above the pad.
Press down the release
buttons on the sides
of the head post, and
both sides of the mop
head will drop open.
2 . Slip the mop head’s 4
corner tabs into the 4
corner pockets of the
Dirt Grip™ Pad.
3. Gently press the
Intelli-Mop Head to the
floor on one side of the
pad, and that side will
click into place.
4 . Flip the other side of the
Intelli-Mop Head over
onto the floor to click
into place.
QUICK START GUIDE
LIF T-AWAY® PRO STEAM POCKET® MOP
With Intelligent Steam Control®

STEAM BLASTER™ TECHNOLOGY
When you need an extra burst of steam to clean tough,
dried messes and stuck-on stains, use the Steam Blaster.
1. Flip back the Intelli-Mop™ Head so that it is behind the
mop body.
2. Tilt the mop handle back. This will cause the Steam
Blaster to emit a concentrated blast of steam onto the
floor.
3 . To stop the Steam Blaster spray, simply tilt the mop
handle forward.
4. Flip the Intelli-Mop Head back into its original position
and continue cleaning.
2
3
1
4
STEAM BLASTER™ TECHNOLOGY
1. Plug the power cord into an
outlet. The STEAM CONTROL
button will flash blue.
2. Press the STEAM COTROL
button to select your steam
setting: once for LO, twice for HI, and three times to
place the unit in STANDBY MODE.
SETTING IDEAL FOR
THESE SEALED
SURFACES
RECOMMENDED USAGE
Tools Laminate
Hardwood
Marble
Light cleaning & dusting
LO
Hardwood
Marble
Tile
Stone
Cleaning most surfaces & large areas
HI Hardwood
Marble
Tile
Stone
Deep cleaning & cleaning
hard-to-clean surfaces
INTELLIGENT STEAM CONTROL®
CLEANING
ABOVE-FLOOR CLEANING
ABOVE-FLOOR CLEANING ACCESSORIES
Remove the Handheld Steamer by pressing the release
button and pulling it away from the cradle.
Snap the desired accessory into the main nozzle of the
Handheld Steamer. Then squeeze the steam trigger to
activate steam.
(Note: Tools mode is only available when using the Handheld
Steamer. When the Handheld Steamer is removed from the
cradle, it will automatically go into Tools mode.)
For questions or to register your product, contact us at: 800-798-7398 or visit us online at sharkclean.com
@sharkcleaning
Once done with handheld steaming, press the STEAM
CONTROL button until the light flashes blue to put the
unit in STANDBY MODE. Let cool for 2 to 3 minutes
before removing mop head, pads, or handheld
accessories and storing.
ACCESSORIES USE HOW TO ATTACH
G ACCESSORY HOSE
For spot cleaning and direct steaming Slide Accessory Hose onto the Handheld Steamer.
H GARMENT STEAMER
Freshen clothing, fabrics, and
upholstery
Slide the Garment or Upholstery Bonnet onto the Garment Steamer.
Elastic will hold the bonnet in place.
Snap the bristle over the Garment Steamer and bonnet then click the
Garment Steamer onto the Handheld Steamer.
I SMALL ABOVE-FLOOR
POCKET TOOL WITH PAD Ideal for small, uneven surfaces. The
pointed tip is great for edges and corners.
Slide the pad onto the Small Above-Floor Pocket Tool so it fits snugly.
Cinch the elastic band and slide the locking toggle to tighten.
Connect the tool to the Accessory Hose by pushing firmly until it clicks
into place, then click the Accessory Hose onto the Handheld Steamer.