Sharp ER-A411 Operating and maintenance manual

ELECTRONIC CASH REGISTER
FULL DETAILED INSTRUCTION MANUAL
MODEL
ER-A411
ER-A421

CAUTION:
The cash register is should be securely fitted to the supporting platform to avoid instability when the
drawer is open.
CAUTION:
The socket-outlet shall be installed near the equipment and shall be easily accessible.
VORSICHT:
Die Netzsteckdose muß nahe dem Gerät angebracht und leicht zugänglich sein.
ATTENTION:
La prise de courant murale devra être installée à proximité de l’équipement et devra être facilement
accessible.
AVISO:
El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible.
VARNING:
Det matande vägguttaget skall placeras nära apparaten och vara lätt åtkomligt.
LET OP:
Het stopcontact dient in de buurt van de kassa en gemakkelijk toegangbaar te zijn.
CAUTION:
For a complete electrical disconnection pull out the mains plug.
VORSICHT:
Zur vollständigen elektrischen Trennung vom Netz den Netzstecker ziehen.
ATTENTION:
Pour obtenir une mise hors-circuit totale, débrancher la prise de courant secteur.
AVISO:
Para una desconexión eléctrica completa, desenchufar el enchufe de tomacorriente.
VARNING:
För att helt koppla från strömmen, dra ut stickproppen.
LET OP:
Trek de stekker uit het stopcontact indien u de stroom geheel wilt uitschakelen.

3
INTRODUCTION
Thank you very much for your purchase of the SHARP Electronic Cash Register, Model ER-A411/ER-A421.
Please read this manual carefully before operating your machine in order to gain full understanding of
functions and features.
Please keep this manual for future reference. It will help you if you encounter any operational problems.
IMPORTANT
• Install the cash register in a location not subject to direct sunlight, unusual temperature changes, high
humidity or splashing water.
Installation in such locations could cause damage to the cabinet and the electronic components.
• Never install the register in saline areas (e.g.: close to the sea).
Installing the register in such locations could cause component failure with the corrosion.
• Never operate the register with wet hands.
The water could seep into the interior of the register and cause component failure.
• When cleaning your register, use a dry, soft cloth. Never use solvents, such as benzine and/or thinner.
The use of such chemicals will lead to discoloration or deterioration of the cabinet.
• The register plugs into any standard wall outlet (official (nominal) voltage).
Other electrical devices on the same electrical circuit could cause the register to malfunction.
• If the register malfunctions, call your authorized SHARP dealer for service - do not try to repair the register
yourself.
• For complete electrical disconnection, disconnect the main plug.
PRECAUTION
This register has a built-in memory protection circuit which is operated by a rechargeable battery pack. It
should be known that all batteries will, in time, dissipate their charge even if not used. Therefore to insure an
adequate initial charge in the protection circuit and to prevent any possible loss of memory upon installation,
it is recommended that each unit be allowed to be recharged for a period of 24 to 48 hours prior to use by
the customer.
In order to charge the battery pack, the machine must be plugged in. This recharging precaution can prevent
unnecessary initial service calls.
The battery pack is a consumable part, and its operating time will get shorter gradually each time it is
recharged for memory backup.
When the battery pack cannot be charged enough to perform memory backup, it means that the service life
of the battery pack has expired.
If this is the case, consult your authorized SHARP dealer.
Caution Scanner connection
In order to allow a plug & play connection of the optional scanner the Pin 9 of the D-Sub connector 1
(Channel 1) uses +5V.
Be very careful of this +5V in case connection of a different device should be done so that a damage of
the register or device is avoided.

4
CONTENTS
INTRODUCTION..............................................................................................................................................3
IMPORTANT ....................................................................................................................................................3
PRECAUTION..................................................................................................................................................3
1 Part Names and Functions .....................................................................................................................9
External View.............................................................................................................................................9
Front view .........................................................................................................................................9
Rear view..........................................................................................................................................9
Printer ......................................................................................................................................................10
Keyboard (ER-A411)................................................................................................................................11
Standard keyboard layout............................................................................................................... 11
Function key list.............................................................................................................................. 11
Optional key list ..............................................................................................................................12
Keyboard (ER-A421) ...............................................................................................................................13
Standard keyboard layout...............................................................................................................13
Function key list..............................................................................................................................13
Optional key list ..............................................................................................................................14
Inserting the keyboard sheet ..........................................................................................................15
RS232 Connector/SD Card Slot ..............................................................................................................16
RS232 connector............................................................................................................................16
SD card slot ....................................................................................................................................16
Displays ...................................................................................................................................................17
Operator display .............................................................................................................................17
Customer display ...........................................................................................................................18
Screen save mode..........................................................................................................................18
2 Selecting an Operating Mode ...............................................................................................................19
Operating Modes .....................................................................................................................................19
Mode Selection........................................................................................................................................20
3 Prior to Making Entries .........................................................................................................................21
Preparations for Entries...........................................................................................................................21
Receipt paper roll ..........................................................................................................................21
Receipt ON/OFF function ...............................................................................................................21
Clerk assignment............................................................................................................................21
Error Warning ..........................................................................................................................................22
Item Selection from the Menu..................................................................................................................23
Starting Cash Memory Entry....................................................................................................................24
4 Entries.....................................................................................................................................................25
Item Entries..............................................................................................................................................25
Single item entries ..........................................................................................................................25
Repeat entries ................................................................................................................................28
Multiplication entries .......................................................................................................................29
Split-pricing entries .........................................................................................................................31
Successive multiplication entries....................................................................................................33
Single item cash sale (SICS)/single item finalize (SIF) entries.......................................................35
Special Entries for PLU/EAN ...................................................................................................................36
Promotion function..........................................................................................................................36
PLU/EAN link entries ......................................................................................................................39
EAN learning function.....................................................................................................................40
PLU/EAN information inquiry (view) function..................................................................................41
EAN price change function
.............................................................................................................42
Set PLU/EAN entries ......................................................................................................................43
PLU level shift (for direct PLUs) .....................................................................................................44

5
Price level shift ...............................................................................................................................46
Condiment entries (for PLU)...........................................................................................................48
Display of Subtotals.................................................................................................................................50
Subtotal ..........................................................................................................................................50
Difference subtotal (Differ ST) ........................................................................................................50
Finalization of Transaction.......................................................................................................................51
Cash tendering ...............................................................................................................................51
Cash sale that does not need any tender entry..............................................................................51
Check tendering .............................................................................................................................52
Check sale that does not need any tender entry ............................................................................52
Mixed tendering (check + cash)......................................................................................................53
Credit sale ......................................................................................................................................53
Mixed-tender sale (cash or check tendering + credit tendering).....................................................54
Computation of VAT (Value Added Tax)/Tax ............................................................................................55
VAT/tax system...............................................................................................................................55
VAT shift entries..............................................................................................................................57
Guest Check (GLU) .................................................................................................................................58
Guest look up (GLU) system ..........................................................................................................58
Deposit entries................................................................................................................................60
Bill printing ......................................................................................................................................61
Transferring guest checks out or in (Transfer-in/out)......................................................................61
Intermediate GLU reading ..............................................................................................................62
Bill totalizing/bill transfer .................................................................................................................63
Bill separating .................................................................................................................................64
Tip-in entries...................................................................................................................................67
Tip Paid Entries ..............................................................................................................................67
Auxiliary Entries.......................................................................................................................................68
Percent calculations (premium or discount) ..................................................................................68
Discount entries .............................................................................................................................69
Refund entries ................................................................................................................................70
Printing of non-add code numbers .................................................................................................70
Payment Treatment .................................................................................................................................71
Currency exchange ........................................................................................................................71
Received-on-account entries..........................................................................................................72
Paid-out entries ..............................................................................................................................73
No-sale (exchange) ........................................................................................................................74
Cash payment transfer ...................................................................................................................75
Cashing a check .............................................................................................................................76
Age Verification........................................................................................................................................77
Electronic Journal View ...........................................................................................................................77
TRAINING Mode......................................................................................................................................78
Overlapped Clerk Entry ...........................................................................................................................79
5 Correction...............................................................................................................................................80
Correction of the Last Entry (Direct Void) ................................................................................................80
Correction of the Next-to-Last or Earlier Entries (Indirect Void)...............................................................81
Subtotal Void............................................................................................................................................82
Correction after Finalizing a Transaction .................................................................................................82
6 Special Printing Function .....................................................................................................................83
After Transaction Receipt / Copy Receipt Printing...................................................................................83
Guest Check Copy...................................................................................................................................84
Receipt for Remote Printers (KP#1 and KP#2) .......................................................................................85
Type of receipts ..............................................................................................................................85
Sorted Receipt Function ..........................................................................................................................86

6
7 Manager Mode........................................................................................................................................89
Entering the Manager Mode ....................................................................................................................89
Override Entries.......................................................................................................................................89
8 Reading (X) and Resetting (Z) of Sales Totals ....................................................................................90
How to take a report .......................................................................................................................90
Flash report ....................................................................................................................................90
Daily Sales Totals ....................................................................................................................................93
General report ................................................................................................................................93
Department report ..........................................................................................................................96
Individual group total report on departments ..................................................................................97
Full group total report on departments ...........................................................................................97
PLU/EAN report (by specified range/pickup)..................................................................................98
PLU/EAN report by associated department....................................................................................99
Individual PLU/EAN group report .................................................................................................100
PLU/EAN group total report..........................................................................................................101
PLU/EAN stock report (by specified range/pickup) ......................................................................101
PLU top 20 sales report (by sales amount/by sales quantity) ......................................................102
PLU/EAN zero sales report (full) ..................................................................................................103
PLU/EAN zero sales report (by dept.) ..........................................................................................103
PLU/EAN category report .............................................................................................................104
Transaction report.........................................................................................................................105
Total in drawer report....................................................................................................................105
Commission sales report ..............................................................................................................105
Individual clerk report ..................................................................................................................106
Individual cashier report ..............................................................................................................108
All clerk report............................................................................................................................... 110
Hourly report................................................................................................................................. 110
All cashier report........................................................................................................................... 110
GLU report by specified range...................................................................................................... 111
GLU report by clerk ...................................................................................................................... 111
Balance report .............................................................................................................................. 111
Periodic Report Sample......................................................................................................................... 112
General information ...................................................................................................................... 112
Daily net report ............................................................................................................................. 112
Compulsory Cash/Check Declaration.................................................................................................... 113
Display sample ............................................................................................................................. 114
Report sample .............................................................................................................................. 114
9 Non-accessed EAN Deletion............................................................................................................... 115
Non-accessed EAN report............................................................................................................ 115
10 Prior to Programming.......................................................................................................................... 116
Programming Keyboard Layout............................................................................................................. 116
ER-A411 ....................................................................................................................................... 116
ER-A421 ....................................................................................................................................... 116
How to Program Alphanumeric Characters ........................................................................................... 118
Mobile phone method (ER-A411)/Text keyboard method (ER-A421)........................................... 118
Entering character codes.............................................................................................................. 119
11 Programming .......................................................................................................................................120
Basic Instructions...................................................................................................................................120
Programming screen ....................................................................................................................120
Programming example .................................................................................................................121
Article Programming ..............................................................................................................................123
Department...................................................................................................................................124
PLU/EAN ......................................................................................................................................126
PLU range ....................................................................................................................................128

7
Set PLU table ...............................................................................................................................129
Link PLU table (for PLU/EAN link)................................................................................................129
PLU condiment table ....................................................................................................................130
Promotion table ............................................................................................................................132
EAN Non-PLU code format ..........................................................................................................134
Press code (for EAN)....................................................................................................................135
PLU/EAN stock.............................................................................................................................136
EAN delete ...................................................................................................................................136
PLU group text..............................................................................................................................136
Direct Key Programming........................................................................................................................137
Direct key......................................................................................................................................137
Functional Programming........................................................................................................................139
Discount key ( -and through )......................................................................................140
Percent key ( through ).....................................................................................................140
Commission..................................................................................................................................141
Miscellaneous functions ...............................................................................................................141
Deposit .........................................................................................................................................141
RA/RA2.........................................................................................................................................142
PO/PO2 ........................................................................................................................................142
Cash tip/Non-cash tip ...................................................................................................................142
Cash in drawer .............................................................................................................................143
Check change...............................................................................................................................143
Media Key Programming .......................................................................................................................144
Cash key (Cash and Cash2 through 5) ........................................................................................145
Check key (Check and Check2 through Check5).........................................................................146
Credit key (Credit1 through Credit9).............................................................................................147
Check cashing (Check1 through Check5) ....................................................................................148
Foreign currency (Foreign1 through Foreign4).............................................................................148
Training Clerk/Cashier Programming ....................................................................................................149
Function Text Programming...................................................................................................................150
Personnel Programming........................................................................................................................152
Clerk .............................................................................................................................................153
Cashier .........................................................................................................................................155
Manager .......................................................................................................................................156
Contactless key ............................................................................................................................157
Prohibition of the contactless key .................................................................................................158
Terminal Programming...........................................................................................................................159
Date/Time Setting ..................................................................................................................................160
Optional Feature Selection ....................................................................................................................161
Function prohibition ......................................................................................................................162
Function selection.........................................................................................................................164
Print selection ...............................................................................................................................166
EURO change ..............................................................................................................................168
Report Programming .............................................................................................................................169
Zero skip.......................................................................................................................................170
Hourly report.................................................................................................................................170
Z1 General report .........................................................................................................................171
Stacked report ..............................................................................................................................173
Message Programming..........................................................................................................................175
Receipt logo..................................................................................................................................175
Entertainment bill message ..........................................................................................................176
Scrolling message for customer display .......................................................................................176
Device Configuration Programming.......................................................................................................177
Built-in printer ...............................................................................................................................178

8
Remote printer (KP#1 and KP#2).................................................................................................179
Scanner ........................................................................................................................................180
Online ...........................................................................................................................................180
Clerk key.......................................................................................................................................180
EFT...............................................................................................................................................180
GLU Code Programming .......................................................................................................................181
Tax Programming...................................................................................................................................182
Tax 1 through 6.............................................................................................................................182
On-line Configuration Programming ......................................................................................................183
VMP Configuration Programming..........................................................................................................184
Automatic Sequencing Key Programming.............................................................................................185
Basic Preset .................................................................................................................................185
Key Sequence ..............................................................................................................................186
Function key list............................................................................................................................187
Reading of Stored Programs .................................................................................................................189
Program reading sequence ..........................................................................................................189
Sample printouts...........................................................................................................................190
SD CARD Mode.....................................................................................................................................203
Inserting and removing an SD memory card ................................................................................203
SD card formatting........................................................................................................................203
Folder creating..............................................................................................................................203
Folder name selecting ..................................................................................................................204
Data saving ..................................................................................................................................204
Data loading .................................................................................................................................205
iSDC Mode ............................................................................................................................................206
Host preset ...................................................................................................................................206
Send item .....................................................................................................................................207
Report...........................................................................................................................................208
Terminating the communication....................................................................................................209
12 Electronic Journal ...............................................................................................................................210
Electronic journal ..........................................................................................................................210
13 European Article Number (EAN) or Universal Product Code (UPC) ............................................... 211
EAN or UPC code......................................................................................................................... 211
Add-on code .................................................................................................................................212
14 EURO Migration Function ...................................................................................................................213
15 Operator Maintenance.........................................................................................................................215
In Case of Power Failure .......................................................................................................................215
In Case of Printer Error..........................................................................................................................215
Cautions in Handling the Printer and Recording Paper.........................................................................215
Cautions in handling the printer....................................................................................................215
Cautions in handling the recording paper (thermal paper) ...........................................................215
Replacing the Paper Rolls .....................................................................................................................216
Recording paper specifications ....................................................................................................216
Removing the paper rolls..............................................................................................................216
Installing the paper rolls................................................................................................................217
Removing a Paper Jam ................................................................................................................218
Cleaning the Printer (Printer Head/Sensor/Roller).................................................................................219
Removing the Till and the Drawer..........................................................................................................220
Opening the Drawer by Hand ................................................................................................................220
Drawer Lock Key ...................................................................................................................................220
Installing the Fixing Angle Bracket.........................................................................................................221
Before Calling for Service......................................................................................................................222
16 Specifications ......................................................................................................................................223

9
1Part Names and Functions
External View
■Front view
Printer cover
Keyboard
(normal type)
Drawer
Drawer lock
SD card slot
Operator
display
ER-A411 ER-A421
Keyboard
(flat type)
■Rear view
1
2
3
4
Customer display
RS232

10
Printer
The printer is a receipt/journal dual station type thermal printer, and therefore it does not require any type of
ink ribbon or cartridge. The average life of the printer is approximately 6 million lines.
When removing the printer cover, lift up its rear.
When installing the printer cover, hook it on the pawls on the cabinet and shut it.
Printer head
Paper cutter
Sensor
Roller
Print roller arm
NOTE Do not attempt to remove the paper with the print roller arm in the hold position. This may result
in damage to the printer and printer head.

11
Keyboard (ER-A411)
■Standard keyboard layout
■Function key list
{Receipt paper feed key 0~ 9:Numeric keys
}Journal paper feed key NNon-add code key
RReceipt print key dDept. number key
FFunction menu key JManager number key
abAutomatic sequencing 1 and 2
keys LClerk number key
rReceived-on-account key 1~
20
Department keys
QPercent menu key |ICursor (up/down) keys
oPaid-out key mMode key
fRefund key cCancel key
~Void key <Credit menu key
-Discount key eElectronic journal view key
UPrice lookup/EAN key =Check menu key
ZInquiry key >Exchange menu key
tEAN price change key EEnter key
@Multiplication key sSubtotal key
PDecimal point key ATotal (cash total) key, or No-sale key
lClear key
* In this manual, each department key is represented like 4in order to distinguish it from direct PLU keys.

12
■Optional key list
000 key Value-added tax shift by transaction key
Page up/down keys Value-added tax shift by item key
Discount menu key Difference subtotal key
uPayment menu key Cashier number key
Cash menu key
~
Clerk entry keys
PLU level shift number key GGuest lookup key
\
~
]PLU level shift keys nNew balance key
PLU price shift number key TFinalization key
~
PLU price shift keys Guest number entry key
Amount entry key Deposit key
Condiments next key Deposit refund key
Repeat key Bill totalize/bill transfer key
~
Percent keys Bill separation by item key
~
Discount keys Bill separation by amount key
Received-on-account 2 key Bill separation by person key
Paid-out 2 key Transfer out key
No-sale key Transfer in key
Guest check copy key Intermediate GLU key
Value-added tax key KGuest check receipt key
qAuto menu key Entertainment bill key
~
Automatic sequencing keys Cash tip key
~
Cash keys Non-cash tip key
~
Check keys Tip paid key
~
Credit keys Receipt switch key
~
Exchange keys Bank console key
NOTE To use optional keys on your register, consult your authorized SHARP dealer.

13
Keyboard (ER-A421)
■Standard keyboard layout
■Function key list
{Receipt paper feed key cCancel key
}Journal paper feed key 1~ 6Department keys*
KGuest check receipt key @Multiplication key
eElectronic journal view key PDecimal point key
FFunction menu key lClear key
qAuto menu key 0~ 9:Numeric keys
LClerk number key uPayment menu key
pPrice lookup/subdepartment key EEnter key
-Discount key ,Bill separation key (by item)
QPercent menu key GGuest lookup key
oPaid-out key nNew balance key
fRefund key TFinalization key
~Void key \~ ]PLU level shift keys
CValue added tax shift key
(by item) sSubtotal key
|ICursor (up/down) keys ATotal (cash total) key, or No-sale key
mMode key 1~
70
Direct PLU keys
* In this manual, each department key is represented like 4in order to distinguish it from direct PLU keys.

14
■Optional key list
000 key a
~
Automatic sequencing keys
Page up/down keys
~
Cash keys
Discount menu key
~
Check keys
Cash menu key
~
Credit keys
=Check menu key
~
Exchange keys
<Credit menu key Value-added tax shift by transaction key
>Exchange menu key Difference subtotal key
PLU level shift number key Cashier number key
PLU price shift number key
~
Clerk entry keys
~
PLU price shift keys JManager number key
dDept. number key Guest number entry key
ZInquiry key Deposit key
tEAN price change key Deposit refund key
Amount entry key Bill totalize/bill transfer key
Condiments next key Bill separation by amount key
Repeat key Bill separation by person key
~
Percent keys Transfer out key
~
Discount keys Transfer in key
rReceived-on-account keys Intermediate GLU key
Paid-out 2 key Entertainment bill key
NNon-add code key Cash tip key
No-sale key Non-cash tip key
Guest check copy key Tip paid key
RReceipt print key Receipt switch key
Value-added tax key Bank console key
NOTE To use optional keys on your register, consult your authorized SHARP dealer.

15
■Inserting the keyboard sheet
Insert the keyboard sheet between the keyboard cover and the cabinet as illustrated below.
Keyboard cover
Keyboard sheet
1. Lift up the keyboard cover.
2. Insert the keyboard sheet into the slit.
3. Close the keyboard cover.
NOTE • Do not spread the keyboard cover too far as it might tear.
• Replace the keyboard sheet with a new one if by chance it gets wet. Use of a wet keyboard
sheet may cause problems.
• Be sure to use only SHARP-supplied keyboard sheets. Thick or hard sheets make key
operations difficult.
• Smooth the keyboard sheet evenly under the keyboard cover, without any folds or wrinkles, to
ensure easier operation.
• If you require a new keyboard sheet, please contact your dealer.
• The keyboard cover will eventually wear out. If your keyboard cover is dirty or broken, replace
the cover with a new one. For details, contact your authorized SHARP dealer.

16
RS232 Connector/SD Card Slot
■RS232 connector
1
2
3
4
RS232
■SD card slot
Refer to the “SD CARD Mode” section.

17
Displays
■Operator display
• Screen example 1 (REG mode)
Sales information area:
When a transaction information occupies more than
3 lines, you can scroll to the direction by using the
|Ikeys. Sales information you have just entered
such as items and prices will appear between 1st line
and 3rd line.
Total is always appear at 4th line.
Numeric entry area
Status area
Mode name or
GLU code
Status information Clerk/cashier code
PLU level shift indicator (L1-L3) : Shows the PLU level currently selected.
Price level shift indicator (P1-P3) : Shows the PLU/EAN price level currently selected.
Receipt ON/OFF status indicator ( ): Appears when the receipt ON-OFF function signs OFF.
VAT shift status indicator (V) : Appears when the VAT status is shifted.
Stock alarm indicator ( ! ) : Appears when the stock of the PLU/EAN which you entered is
zero, negative or reaches the minimum stock.
Electronic journal near full indicator ( ) : Appears ( ) when the used memory is 80%.
: Appears ( ) when the used memory is 90%.
: Appears ( ) when the used memory is 95%.
Sentinel mark ( ): Appears when the cash in drawer exceeds a programmed sentinel
amount. The sentinel check is performed for the total cash in
drawer.
VMP file full indicator (1, 2, or 3) : When a VMP file used memory is 90% or more, its file number is
indicated.
Unsent data alarm indicator ( ): Appears when there is unsent electronic journal data or sales
data.

18
• Screen example 2 (PGM2 mode)
Programming area:
Programmable items are listed.
Status area
Mode name Character indicators Clerk/cashier code
The character indicators consist of the following:
Case/caps lock indicator (A/a) : The upper-case letter “A” or lower-case letter “a” appears
during text programming. When caps lock is on, the character
is highlighted.
Double-size character mode indicator (W) : Appears when the double-size character mode is selected
during text programming.
The display can be tilted back and forth to the
best operational viewing angle.
NOTE
Do not try to force the display beyond its full
position.
■Customer display
Text/message display area
Numeric display area
The register can display a programmed scrolling message on the text/message display area.
To use this function, you need to program the following functions in the PGM2 mode:
• Scrolling message text (SCROLL MESSAGE in MESSAGE menu)
• Waiting time (WAITING TIME in TERMINAL menu)
■Screen save mode
When you want to save the electric power or save the display’s life, use the screen save function. This
function can turn off the display and the LCD backlight when any clerk does not operate the register for an
extended period of time. You can program the time for which your register should keep the normal status (in
which the backlight is “ON”) before it goes into the screen save mode.
This machine will enter the screen save mode two minutes later by default.
To go back to the normal mode, press any key.
The backlight in display is a consumable part.
When the LCD display may no longer be adjusted and become darker, you should replace the LCD unit.
Consult your authorized SHARP dealer for further details.

19
2Selecting an Operating Mode
When you turn the register on and press the mkey, the mode selection window will appear on the display.
For example, when a clerk is signed on, the following window will appear.
Mode selection window
Operating Modes
You can select any mode other than REG from the list in the mode selection window. Your register supports
the following operating modes:
REG mode
This mode allows you to enter various sales information. The mode selection
window does not list this mode. To select this mode from the mode selection
window, press the ckey.
OPXZ mode This mode allows clerks to take X or Z reports on their sales information.
OFF mode This mode locks all operations of the register. When you select this mode, the
window will disappear. Pressing any key turns the register ON.
X1/Z1 mode This mode is used to take various daily total reports (X1/Z1 reports).
X2/Z2 mode This mode is used to take various weekly or monthly reports (X2/Z2 reports).
PGM1 mode This mode allows you to program those items which need to be changed often such
as unit prices and discount percentages.
PGM2 mode This mode allows you to program all items including date, time, functions, and the
items that can be programmed in the PGM1 mode.
AUTO KEY mode This mode allows you to program AUTO menu keys and automatic sequencing
keys.
SD CARD mode This mode allows you to save and load the data of your register to and from an SD
card.
iSDC mode This mode allows you to save and load the data of your register to and from the
server using a WiFi SD card.

20
Mode Selection
Procedure
Press the mkey. The following mode screen is displayed when a clerk is signed on.
Use one of the following ways:
• Move the cursor to the desired option by using the |or Ikey, and press the Ekey.
• Enter the desired option number by using a numeric key and press the Ekey.
NOTE When you want to enter the REG mode, simply press the ckey.