SHINE 6000X-HD User manual

6000X-HD INSTRUCTION MANUAL

- English -
2 English
6000X-HD
Welding helmet with 3 memory functions and true color ADF
WARNING Read and Understand All Instructions Before
Using the Equipment.
SAFETY WARNINGS
The auto-darkening helmet with improved High Denition Filter
Optics delivers a new generation of face and eye protection.
Advanced integrated technology such as LCD, optoelectronics
detection, solar power, and microelectronics are coordinated
to produce one of the safest, fastest and most reliable auto-
darkening helmets available.
The auto-darkening helmet not only can efciently protect
operator’s eyes and face from sparks, spatter, and harmful
radiation under normal welding conditions, but also can make
both hands free and strike arc accurately resulting in increased
efciency and improved quality welds. It may be widely used for
various welding, cutting, spraying and arc gouging, etc.
• This auto-darkening helmet is not suitable for “overhead”
welding, laser welding/cutting, or oxyacetylene welding/
cutting applications.
• This helmet will not protect against explosive devices or
corrosive liquids. Machine guards or eye splash protection
must be used when these hazards are present.
• Impact resistant, primary eye protection, spectacles or
goggles that meet current ANSI specications must be worn
at all times when using this welding helmet.
• Avoid work positions that could expose unprotected areas of
the body to spark, spatter, direct and/or reected radiation.
Use adequate protection if exposure cannot be avoided.
• Do not make any modications to either the ADF cartridge or
helmet, other than those specied in this manual.
• Do not use any replacement parts other than those specied
in this manual. Unauthorized modications and replacement
parts will void the warranty and expose the user to the risk
of personal injury.
• Do not immerse this helmet in water because this model is
not waterproof.
• Do not use any solvents on any ADF or helmet components.
• The recommended operating temperature range for this
ADF cartridge is -10°C~65°C (14°F~149°F). Do not use this
device beyond these temperature limits.
Failure to follow these warnings and/or failure to follow all of the
operating instructions could result in severe personal injury.
CONTENTS
1. Specications
2. Operation Instruction
3. True Color
4. Maintenance
5. Trouble Shooting
6. Warranty & Replacement Parts
7. Parts List
8. Recommended Shade Numbers
1. SPECIFICATIONS
The specications of the 6000X-HD helmet are the following:
1. ADF Cartridge size 114 x 133 x 9.5 mm (4.5” x
5.25” )
2. LCD Viewing area 100 x 83.4 mm (3.94” x 3.28”)
3. Light State Shade DIN 4
4. Dark Variable Shades DIN 5-9 / 9-13
5. UV/IR Protection Up to DIN 15 at all times
6. Switching time (light to 0.08ms
dark)
7. Delay time (dark to light) Adjustable (1-5 for 0.1-0.9s)
8. Sensitivity Adjustable (1-5 for low-high)
9. Arc Sensors 4
10. Grind Function Yes
11. Memory Settings 3
12. Power Supply Solar and CR2450 battery
13. Operating Temperature -10°C~65°C (14°F~149°F)
14. Inside PC lens 106 x 89.5 x 1 mm
15. Outside PC lens 114 x 133 x 1 mm (4.5” x5.25”)
16. Standards CE EN379, ANSI Z87.1, CSA
Z94.3, AS/NZA
17. Warranty 2 years

- English -
3English
2. OPERATION INSTRUCTION
BEFORE USE
• Check for light tightness and check the inside & outside
protection lens are clean and that no dirt is covering the
sensors on the front of the auto-darkening-lter (ADF)
cartridge.
• Make sure the protection lms on both inside & outside
protection lens are removed.
• Inspect all operating parts for signs of wear or damage.
Any scratched, cracked, or pitted parts should be replaced
immediately.
SCREEN ICON EXPLANATION
1. Battery status
2. Welding indication
3. Grinding indication
4. Shade range 5-9
5. Shade range 9-13
6. Sensitivity indication:
1 (low) to 5(high)
7. Delay indication:
1 (short 0.1s) to
5 (long 0.9s)
8. Shade reading
9. Memory selection
A representation of the view is the following:
Note: Buttons on the left of the screen need to be pressed twice
to start any settings. Otherwise they will not operate.
VARIABLE SHADE CONTROL
• If the Shade is in the range of 5~9, press WELD/GRIND
button repeatedly until both icon 2 and icon 4 appear on
the screen. Then press SHADE button repeatedly until the
desired Shade shown in Icon 8.
• If the Shade is in the range of 9~13, press WELD/GRIND
button repeatedly until both icon 2 and icon 5 appear on
the screen. Then press SHADE button repeatedly until the
desired Shade shown in Icon 8.
Note: Choose an optimum Shade number for the required
welding process or application (see Table 1). If this ADF does not
darken when striking arc, stop welding immediately and contact
our representative.
SENSITIVITY CONTROL
The responsive to different light levels in various welding
processes can be adjusted in the range 1-5 (from low to high).
• Press the SENSITIVITY button twice to start the setting. The
Icon 6 on the screen ashes (from 1 to 5). Repeatedly press
the SENSITIVITY button until the desired level shown in Icon
6.
• Turn to 1 (low) : The photosensitivity changes to be lower.
Suitable for high amperage welding and welding in bright
light conditions (lamp light or sun light).
• Turn to 5 (high) : The photosensitivity changes to be higher.
Suitable for low amperage welding and using in poor light
conditions and suitable for using with steady arc process
such as TIG welding.
Under normal use, a higher sensitivity setting is recommended.
DELAY CONTROL
The length of time delay for the ADF returns to light state after
welding can be adjusted in the range 1-5 (for 0.1~0.9s). The time
delay is for protection of welder’s eyes from strong residual rays
after welding.
• Press the DELAY button twice to start the setting. The Icon 7
on the screen ashes (from 1 to 5). Repeatedly press the
DELAY button until the desired length of time delay shown
in Icon 7.
• Turn to 1 (0.1s) : The time the ADF lighten after welding to
be shorter. The shortest time is about 0.1s depending upon
welding point temperature and shade set. This setting is ideal
for track welding or production welding with short welds.
• Turn to 5 (0.9s) : The time the ADF lighten after welding to
be longer. The longest time is about 0.9s depending upon
welding point temperature and shade set. This setting
is ideal for welding at high amperage where there is an
afterglow from the weld.

- English -
4 English
GRIND SELECTION
• Press WELD/GRIND button repeatedly until icon 3 appears
on the screen and the red light beside the button ashes.
Additionally, icon 8 will show shade 4.
Note: Do not weld in the Grind mode, the ADF will not darken.
MEMORY SETTING
3 most frequently used setting can be stored and reactivated
easily by using the 3 MEMORY buttons on the right side of the
screen.
Upon use of this helmet, the last ADF settings will be stored
automatically (stored about 5 minutes after). The next time
when you start to weld, the last settings will be automatically re-
activated.
• If you want to store a completed welding setting, press and
hold one of the memory buttons and stop pressing when the
icon 9 stops ashing.
• To activate the stored memory, press the memory button.
Note: Only in welding status you can activate the memory.
Change to welding if you are currently using the grinding function.
HEADGEAR ADJUSTMENTS
Because the shapes of man’s heads vary from person to person.
The work positions and the observing angles are different.
Operator may adjust the headband in 5 parameters:
1. Select eye level by Headband adjusting buttons.
2. Select view angle by Segmental positioning plate.
3. Adjust head size perimeter by pushing and turning the
headband tightness adjusting knob.
4. Select eyes distance from ADF by adjusting Headgear
screws to 1 of the 5 slots on the Headgear slider. Make sure
both sides are equally positioned for proper vision.
5. Select the height of the headgear by adjusting the Block
washers up or down on the Block washer adjustment.
BATTERY INDICATOR
Icon 1 indicates the battery status. Replace the battery when it is
low, otherwise, the ADF switching time will become slower and
shade accuracy will be compromised.
POWER SUPPLY AND REPLACE THE BATTERY
The power of the auto-darkening helmet is provided by solar cells
and 1pcs of CR2450 lithium battery.
When change the battery, open the Battery holder at the side of
the ADF and replace the battery.
3. TRUE COLOR
The auto-darkening helmet is a True Color welding helmet.
With advanced True Color technology, the users can weld
with improved clarity due to new complex coating technology,
grind with precision while in grind mode and nally see the job
performance in the light state in the full spectrum of colors. There
is no need to remove the helmet to see clearly! Results are
enhanced the weld quality, increased efciency and improved
safety because the users can see more.
4. MAINTENANCE
The auto-darkening helmet needs little maintenance. Use a
clean, soft piece of cloth moistened with soft soap / pure alcohol
/ commercial disinfectant to wipe the inside and the outside of
the helmet.
Store the product in a dry environment.
Note: Do not immerse the helmet or ADF in water directly.
5. TROUBLE SHOOTING
Trouble Remedy
The ADF does
not darken when
welding.
• Stop welding or cutting immediately.
• Make sure the sensors are facing
the arc and no obstructions.
• Check the mode that is on WELD
not GRIND.
• Review sensitivity recommendations
and adjust sensitivity if possible.
• Replace the battery if necessary.
The ADF stays
dark after welding
or there is no arc
present.
• Adjust the sensitivity to the lower
level (level 1).
• If the welding place is extremely
bright, it is recommended to reduce
the surrounding light level.
The ADF switching • Increase the sensitivity if possible.
during the
welding.
• Make sure the sensors are facing
the arc and no obstructions.
• Increase Delay 0.1 − 0.3 second
may also reduce switching.
Inconsistent shade • It is a natural feature and will not be
number on the
corner of ADF.
dangerous for the eyes.
• In order to get a maximum comfort,
try to keep an view angle at around
90°.
6. WARRANTY & REPLACEMENT PARTS
WARRANTY
The auto-darkening helmets are warranted for 2 years from the
date of purchase. The duration of use depends on various factors
such as use, cleaning storage and maintenance. Frequently
inspections and replacement if it is damaged are recommended.
REPLACEMENT PARTS
13.01.051 Outer protection lens
13.01.052 Inner protection lens
13.01.011 Headgear complete (HG2003)
13.01.012 Sweatband Headgear
13.06.200 Auto darkening lter 6000X-HD

- English -
5English
7. PARTS LIST
ATTENTION if any of these conditions is not kept or
followed, the warranty is automatically invalid.
8. RECOMMENDED SHADE NUMBERS
1. Helmet shell
2. Headgear screw
3. Outer protection lens
4. ADF cradle
5. Magnifying lens holder
6. Cradle lock
7. Auto lter
8. Battery holder
9. Battery
10. Inner protection lens
11. ADF setting panel
12. Memory buttons(3)
13. Weld/Grind button
14.Delay button
15. Sensitivity button
16. Shade button
17. Block washer(on left)
18. Headgear slider (with
5 slots)
19. Headband tightness
adjusting knob
20. Headband
adjustment(back and
forth)
21. Block washer
adjustment(up and down)
22. Headband screw(long, on
right)
23. Block washer (on right)
24.Segmental positioning
plate (on right)
25. Headband adjusting
buttons
26. Positioning point for the
segmental plate