Shure A400SM User manual

Models A400SM, A400XLR, A400SMXLR and
A99SMA User Guide
©2005 Shure Incorporated
27C3022 (Rev. 5)
Printed in U.S.A.
GENERAL
The following accesories allow you to install a shock mount for
gooseneck microphones in permanent installations.
A400SM Shock Mount . Employs Shure Shock-Stopper™ con-
struction, which reduces the transmission of impact or surface
noise by up to 20 dB. Fits a variety of gooseneck microphones.
A400SMXLR. Adds the A400XLR insert and a 3-pin XLR-type (fe-
male) quick-release connector to the A400SM Shock Mount.
A400XLR. Retrofits existing A400SM shock mounts for quick re-
lease. Includes the A400XLR connector and insert.
A99SMA Adaptor. Allows you to mount the A400SM Shock Mount
in holes drilled for use with the A99SM Shock Mount (up to a
2¼ inch diameter).
COMPONENTS OF THE A400SMXLR
FIGURE 1
INSTALLING THE A400SM
1. Drill a 44 mm (1 3/4 in.) hole through mounting surface.
2. Use the shock mount as a template to drill pilot holes.
3. Fasten shock mount to surface with supplied screws.
FIGURE 2
INSTALLING THE A400SMXLR
1. Thread cable through grommet, shock mount and insert.
2. Connect cable to A400XLR Connector using two-conductor
shielded microphone cable (Figure 3).
3. Snap connector into insert. Extend locking screw through hole
by turning screw clockwise, locking XLR connector in place
(Figure 4).
4. Insert connector/insert into shock mount. Stretch grommet
over lip at bottom of insert to secure insert to shock mount.
A400XLR
A400XLR CONNECTOR TERMINALS
FIGURE 3
A400XLR WITH LOCKING SCREW (A)
FIGURE 4
A400XLR
Connector
A400XLR
Insert
Cable
A400SM
Shock Mount
Rubber Grommet
G
12
3
SHIELD RED ( + )
BLACK ( – )
A

INSTALLING THE A99SMA ADAPTOR
1. Remove A99SM Shock Mount from mounting surface by
removing screws.
2. Attach A99SMA Shock Mount Adaptor to surface using exist-
ing screw holes and provided screws (Figure 5).
3. Insert A400SM Shock Mount into adaptor, aligning screw
holes in shock mount with those in adaptor. Attach using
provided screws (Figure 5).
MOUNTING THE A400SM USING THE A99SMA
FIGURE 5
A400SM
Shock Mount
A99SMA
Adaptor
Mounting
Surface
(0.56 in.)
66.70 mm
19.4 mm
(0.765 in.)
52.4 mm
(2.062 in.)
(2.625 in.) 14.40 mm 14.40 mm
(0.56 in.)
(2.00 in.)
50.80 mm
(1.70 in.)
43.18 mm
BEFESTIGUNGSFLANSCH
BRIDA DE MONTAJE
MOUNTING FLANGE
BRIDE DE MONTAGE
FLANGIA DI MONTAGGIO
ASSEMBLAGE DE LA MONTURE SILENT–BLOC
SCHWINGDÄMPFER–BAUGRUPPE
SOPORTE AMORTIGUADO
SUPPORTO ANTIVIBRAZIONE
SHOCK MOUNT ASSEMBLY
38 mm
(1.5 in.)
(Actual Size)
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: [phone] U.S. Fax: [phone] Intl Fax: [phone]
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: [phone] Fax: [phone]
Asia, Pacific:
Shure Asia Limited, Phone: [phone] Fax: [phone]