SICK GM700-02 User manual

OPERATING INSTRUCTIONS
GM700
In-Situ Gas Analyzer Probe Version
Installation, Operation, Maintenance

Described product
GM700
Measuring Probe Version
Version GM700-02, GM700-03, GM700-04, GM700-05, GM700-07, GM700-08,
GM700-09
Manufacturer
SICK AG
Erwin-Sick-Str. 1
79183 Waldkirch
Germany
Production location
SICK AG
Nimburger Str. 11 · D-79276 Reute · Germany
Legal information
This work is protected by copyright. Any rights derived from the copyright shall be
reserved for SICK AG. Reproduction of this document or parts of this document is only
permissible within the limits of the legal determination of Copyright Law. Any modifica‐
tion, abridgment or translation of this document is prohibited without the express writ‐
ten permission of SICK AG.
The trademarks stated in this document are the property of their respective owner.
© SICK AG. All rights reserved.
Original document
This document is an original document of SICK AG.
2O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice

Contents
1 About this document........................................................................ 7
1.1 Function of this document....................................................................... 7
1.2 Scope of application................................................................................. 7
1.3 Target groups (and document structure)................................................. 7
1.4 Further information................................................................................... 7
1.5 Data integrity............................................................................................. 7
1.6 Symbols and document conventions...................................................... 8
1.6.1 Warning symbols...................................................................... 8
1.6.2 Warning levels / Signal words................................................. 8
1.6.3 Information symbols................................................................ 8
2 Safety information............................................................................ 10
2.1 Main operating information..................................................................... 10
2.2 Warning information on the device.......................................................... 13
2.3 Intended use............................................................................................. 15
2.4 Responsibility of user............................................................................... 15
3 Product description........................................................................... 16
3.1 Product identification............................................................................... 16
3.2 Product characteristics............................................................................ 16
3.3 Device variants......................................................................................... 16
3.4 Options...................................................................................................... 16
3.5 Layout and function.................................................................................. 17
3.6 Purge air unit............................................................................................. 17
3.7 Check cycle............................................................................................... 18
3.8 GMP and GPP measuring probes ........................................................... 18
3.8.1 GMP measuring probe in detail.............................................. 19
3.8.1.1 Gas connection for sample gas sampling on
purge air fixture of GMP measuring probe............ 20
3.8.2 GPP gas diffusion probe in dry or wet version....................... 20
3.8.2.1 GPP measuring probe gas connections for zero
and span gas........................................................... 21
4 Transport and storage....................................................................... 22
4.1 Transport protection................................................................................. 22
4.2 Storage...................................................................................................... 22
5 Mounting............................................................................................. 24
5.1 Assembly information............................................................................... 24
5.2 Tools required............................................................................................ 24
5.3 Preparing the measuring point................................................................ 24
5.4 GM700 scope of delivery......................................................................... 25
5.5 Installation sequence............................................................................... 25
5.5.1 Installation example................................................................ 25
5.5.2 Overview of installation steps (duct-side preparation).......... 26
CONTENTS
8022447/0000/2018-01 | SICK O P E R A T I N G I N S T R U C T I O N S | GM700 3
Subject to change without notice

5.5.3 Installation preparation for the purge air unit........................ 26
5.5.4 Installing the flange with tube................................................. 26
5.5.5 Installing the control units...................................................... 27
5.5.5.1 Install the control unit away from the SR-unit....... 29
5.5.6 Installing the terminal box (option)......................................... 30
5.5.7 Installing the purge air unit..................................................... 30
6 Electrical installation........................................................................ 31
6.1 Electrical installation safety information................................................. 31
6.2 Connection overview................................................................................ 32
6.2.1 Lines......................................................................................... 33
6.2.2 Information on laying lines...................................................... 33
6.3 Connecting I/O interfaces........................................................................ 34
6.3.1 Leading the CAN bus line correctly through the PG screw
fitting........................................................................................ 34
6.3.2 Wiring the evaluation unit....................................................... 35
6.3.3 Customer wiring of the terminal box (optional)...................... 37
6.4 Connecting the SR-unit............................................................................. 38
6.5 Grounding conductor, evaluation unit..................................................... 38
7 Commissioning.................................................................................. 40
7.1 Safety information on commissioning..................................................... 40
7.2 Prerequisites for successful commissioning.......................................... 40
7.3 Overview of commissioning steps........................................................... 41
7.4 Material required ..................................................................................... 42
7.4.1 Material required - included in scope of delivery................... 42
7.5 Fitting the SR-unit on the purge air fixture of the measuring probe...... 43
7.6 Optical fine alignment for device versions for NH3 and HF measure‐
ment.......................................................................................................... 43
7.7 Optical fine alignment on the version for HCI measurement................ 45
7.8 Two types of zero point checks................................................................ 46
7.8.1 Selecting the ambient temperature range............................. 46
7.8.2 Carrying out zero adjust (on the measuring path free from
sample gas).............................................................................. 47
7.8.3 Zero point check with GPP measuring probe......................... 47
7.9 Repositioning the probe reflector............................................................ 48
7.10 Fitting the measuring probe on the flange with tube............................. 51
7.11 Putting the purge air unit into operation................................................. 52
7.12 Fitting the sender/receiver unit on the intermediate housing............... 52
7.13 Installing the weatherproof cover ........................................................... 53
7.14 Starting measuring operation.................................................................. 54
7.14.1 Operating states...................................................................... 55
7.14.2 Select the ambient temperature range.................................. 55
8 Operation............................................................................................ 56
8.1 Safety......................................................................................................... 56
8.1.1 Check before start-up.............................................................. 56
CONTENTS
4O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice

8.2 Operating and display elements (evaluation unit).................................. 56
8.3 Menu tree of the evaluation unit............................................................. 58
8.3.1 Menu tree Measuring.............................................................. 58
8.3.2 Menu tree Diagnosis............................................................... 58
8.3.3 Menu tree Parameter.............................................................. 59
8.3.4 Menu tree Calibration.............................................................. 61
8.3.5 Menu tree Maintenance.......................................................... 61
8.4 Operating using the serial interface........................................................ 62
8.4.1 Significance of command line elements................................ 62
8.4.2 Setting for serial interfaces..................................................... 62
8.4.3 Serial interface commands - Meas........................................ 62
8.4.3.1 Serial interface command - MEAS ........................ 62
8.4.4 Serial interface commands - Diag.......................................... 62
8.4.4.1 Table with warning messages................................ 62
8.4.4.2 Error messages Table ............................................ 63
8.4.4.3 View the device configuration................................ 63
8.4.4.4 Check the system state and configuration........... 63
8.4.4.5 Call up diagnostic data........................................... 63
9 Maintenance...................................................................................... 64
9.1 Safety......................................................................................................... 64
9.2 Maintenance plan..................................................................................... 65
9.2.1 Maintenance protocol.............................................................. 65
9.2.2 Expendable, wearing and spare parts.................................... 65
9.3 Preparatory work....................................................................................... 66
9.4 Removing the SR-unit from the intermediate housing........................... 66
9.5 Visual check.............................................................................................. 67
9.6 Cleaning the optical interfaces................................................................ 67
9.7 Cleaning the purge air unit....................................................................... 69
10 Troubleshooting................................................................................. 70
10.1 Safety......................................................................................................... 70
10.2 Monitoring and diagnostic system........................................................... 70
10.3 Device not functioning.............................................................................. 71
10.4 Evaluation unit not functioning................................................................ 71
10.4.1 Communication fault between evaluation unit and receiver 72
10.5 Error messages......................................................................................... 72
10.5.1 Error messages........................................................................ 72
10.5.2 Warning messages.................................................................. 74
10.6 Repairing inadequate purge air supply................................................... 74
10.7 Corrosion on flange.................................................................................. 75
11 Decommissioning............................................................................. 76
11.1 Safety information for decommissioning................................................ 76
11.2 Removing the device................................................................................ 77
11.3 Preparing the device ready for shipping.................................................. 77
CONTENTS
8022447/0000/2018-01 | SICK O P E R A T I N G I N S T R U C T I O N S | GM700 5
Subject to change without notice

11.4 Environmentally compatible disposal ..................................................... 78
12 Technical data.................................................................................... 79
12.1 System: GM700........................................................................................ 79
12.2 Sender/receiver unit................................................................................ 80
12.3 GMP measuring probe.............................................................................. 80
12.4 GPP measuring probe............................................................................... 80
12.5 Evaluation unit: Sheet steel enclosure.................................................... 81
12.6 Evaluation unit: Cast metal enclosure..................................................... 82
12.7 Terminal box.............................................................................................. 82
12.8 Dimension drawings, sender/receiver unit ............................................ 83
12.9 Dimension drawings, open measuring probe (GMP).............................. 84
12.10 Dimension drawings GPP measuring probe (Gas Permeable Probe).... 85
12.11 Dimension drawing evaluation unit......................................................... 86
12.12 Dimension drawings: Mounting flange DN125....................................... 87
12.13 Dimension drawing terminal box............................................................. 87
12.14 Dimension drawing, purge air unit........................................................... 88
12.15 Dimension drawing, weatherproof cover, sender/receiver unit............. 88
13 Annex.................................................................................................. 89
13.1 Possible ambient temperatures............................................................... 89
13.1.1 Ambient temperature ranges (closed cell)............................. 89
13.2 User information on laser safety GM700................................................ 89
14 Index.................................................................................................... 91
CONTENTS
6O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice

1 About this document
1.1 Function of this document
These Operating Instructions describe:
•Device components
•Installation
•Operation
•Maintenance work required for reliable operation
1.2 Scope of application
These Operating Instructions are only applicable for the measuring device described in
the product identification.
They are not applicable for other SICK measuring devices.
The standards referred to in these Operating Instructions are to be observed in the
respective valid version.
1.3 Target groups (and document structure)
This Manual is intended for persons installing, operating and maintaining the device.
Operation
The device may only be operated by qualified persons who, based on their device-spe‐
cific training and knowledge as well as knowledge of the relevant regulations, can
assess the tasks given and recognize the hazards involved.
Installation and maintenance
Skilled persons are required for installation and maintenance.
Please observe the information at the beginning of the respective Sections.
1.4 Further information
•Operating Instructions of the purge air supply
•Final inspection record
NOTE
bObserve all supplied documents.
1.5 Data integrity
SICK AG uses standardized data interfaces such as, for example, standard IP technol‐
ogy, in its products. The focus here is on product availability and features.
SICK AG always assumes that the customer is responsible for the integrity and confi‐
dentiality of data and rights involved in connection with using the products.
In all cases, the customer is responsible for the implementation of safety measures
suitable for the respective situation, e.g., network separation, firewalls, virus protection
and patch management.
ABOUT THIS DOCUMENT 1
8022447/0000/2018-01 | SICK O P E R A T I N G I N S T R U C T I O N S | GM700 7
Subject to change without notice

1.6 Symbols and document conventions
1.6.1 Warning symbols
Table 1: Warning symbols
Symbol Significance
Hazard (general)
Hazard by voltage
Hazard by oxidizing substances
Hazard by laser radiation
Hazard by toxic substances
Hazard by noxious substances
Hazard by high temperature
Hazard for the environment/nature/organic life
1.6.2 Warning levels / Signal words
DANGER
Risk or hazardous situation which will result in severe personal injury or death.
WARNING
Risk or hazardous situation which could result in severe personal injury or death.
CAUTION
Hazard or unsafe practice which could result in less severe or minor injuries.
Notice
Hazard which could result in property damage.
Note
Hints
1.6.3 Information symbols
Table 2: Information symbols
Symbol Significance
Important technical information for this product
1 ABOUT THIS DOCUMENT
8O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice

Symbol Significance
Important information on electric or electronic functions
ABOUT THIS DOCUMENT 1
8022447/0000/2018-01 | SICK O P E R A T I N G I N S T R U C T I O N S | GM700 9
Subject to change without notice

2 Safety information
2.1 Main operating information
Lifting and carrying
WARNING
Injury risk through incorrect lifting and carrying of the device
Injuries can occur due to the weight and projecting enclosure parts when the equip‐
ment tips over or drops.
bConsider the device weight before lifting.
bObserve the regulations for protective clothing (e.g., safety shoes, non-slip gloves).
bGrip underneath the equipment when possible to carry it safely.
bDo not use projecting parts on the device to carry the device.
bCall in further personnel for assistance as required.
bUse a hoist or transport equipment as an option.
bPay attention to the transport safety device.
bClear obstacles that could cause falls and collisions out of the way.
DANGER
Risk for system safety through work on the device not described in these Operating
Instructions
Carrying out work on the device not described in these Operating Instructions or associ‐
ated documents can lead to unsafe operation of the measuring system and therefore
endanger plant safety.
bOnly carry out the work on the device described in these Operating Instructions
and associated documents.
Laser radiation
WARNING
Eye injuries through laser radiation
The invisible laser beam within the SR-unit is not accessible when fitted. Observe the
following when the SR-unit of the device is swiveled open during installation work for
test purposes and the laser beam is activated:
bNever look directly into the laser aperture when opening the SR-unit.
bLaser protection class 1: Wear laser protection glasses despite low radiation.
bObserve national valid limit values and standards that refer to these for industrial
safety.
Laser radiation, HF version
CAUTION
Pay attention to device software version
As the limit values of laser class 1 of the IEC 60825-1:2014-5 are neither exceeded in
single case malfunctions nor normal operation under consideration of the service and
measuring state, the device is classified as laser class 1. Prerequisite is using device
software 9105060_YEK0 or newer.
bLaser class 1 of the IEC 60825-1:2014-5: Only use device software
9105060_YEK0 or a newer software version.
2 SAFETY INFORMATION
10 O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice

DANGER
Important information for safe handling of the GM700 SR-unit on the device version
with HF measurement
For device software versions before 9105060_YEK0, a higher laser radiation might
occur.
bLaser class 1 of the IEC 60825-1:2014-5: Only use device software
9105060_YEK0 or a newer software version.
bNever look directly into the laser aperture when opening the SR-unit.
bAlways wear laser goggles or switch the device off during maintenance work.
bObserve valid national limit values and respective standards for work safety.
NOTICE
Deviations of EN60825-1:2014-08 “Laser safety” from the Directive 2006/25/EC
The Directive has been adapted to cover changes in the health and safety regulation for
artificial optical radiation. Deviations occurred through changes in EN60825-1:2014-08
“Laser safety” from Directive 2006/25/EC.
bAlways observe the user information in the Annex of these Operating Instructions!
Escaping hot gas
DANGER
Risk of fire through hot gas escaping in installations with overpressure conditions
On installations with overpressure, the purge air hose can be severely damaged by
escaping hot gas and can catch fire depending on the temperature. On installations
with overpressure and gas temperatures over 200°C at the same time:
bRegularly check the functionality of the reverse flow safeguard in the purge air fix‐
tures.
DANGER
Danger to life by leaking hot/toxic gases
Hot and/or noxious gases can escape during work on the gas duct, depending on the
plant conditions.
bWork on the gas duct may only be performed by skilled technicians who, based on
their technical training and knowledge as well as knowledge of the relevant regula‐
tions, can assess the tasks given and recognize the hazards involved.
SAFETY INFORMATION 2
8022447/0000/2018-01 | SICK O P E R A T I N G I N S T R U C T I O N S | GM700 11
Subject to change without notice

Electrical safety
WARNING
Endangerment of electrical safety during installation and maintenance work when the
power supply is not switched off
An electrical accident can occur during installation and maintenance work when the
power supply to the device and/or lines is not switched off using a power isolating
switch/circuit breaker.
bBefore starting the work, ensure the power supply can be switched off using a
power isolating switch/circuit breaker in accordance with DIN EN 61010.
bMake sure the power isolating switch is easily accessible.
bAn additional separation device is mandatory when the power isolating switch can‐
not be accessed or only with difficulty after installation of the device connection.
bThe power supply may only be switched on again after work completion or for test
purposes by the persons carrying out the work under consideration of the valid
safety regulations.
DANGER
Endangerment of electrical safety through missing power isolating switch
An electrical accident can occur during installation and maintenance work when the
power supply to the device and/or lines cannot be switched off using a power isolating
switch/circuit breaker.
bEnsure the power supply can be switched off using a power isolating switch/circuit
breaker in accordance with DIN EN 61010-1:2010.
bAn additional separation device is mandatory when the power isolating switch can‐
not be accessed or only with difficulty after installation of the device connection.
WARNING
Endangerment of electrical safety through power cables with incorrect rating
Electrical accidents can occur when the specifications for replacement of a removable
power cable have not been adequately observed.
bAlways observe the exact specifications in the Operating Instructions (Technical
Data Chapter) when replacing a removable power line.
Potential equalization
CAUTION
Device damage through incorrect or non-existing grounding
To avoid device damage, a correctly connected potential equalization is mandatory on
all system components with external ground connections in all operating conditions.
bConnect a potential equalization on all planned points on the device components.
bEnsure the potential equalization is connected during all work on the device
described in these Operating Instructions.
2 SAFETY INFORMATION
12 O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice

Contamination caused by purge air failure
CAUTION
A faulty purge air supply can damage the measuring system
The measuring system can no longer be protected from contaminated sample gas and
is damaged.
bWhen the purge air supply appears faulty, immediately perform all actions
described in these Operating Instructions.
Responsibility for system safety
NOTICE
Responsibility for system safety
The person setting the system up is responsible for the safety of the system in which
the device is integrated.
2.2 Warning information on the device
GM700 SR-unit
1
1
2 2
Figure 1: Warning information on the sender/receiver unit
SR-unit, front side
1 Danger sign: Laser radiation
2 Type plate GM700
SR-unit, right side
1 Danger sign: Laser radiation
2 Type plate GM700
Laser sign
The wavelength of the laser varies for the respective measuring components (NH3, HF,
HCl). The maximum laser output at the optical interface depends on the respective
measuring component and is shown on the laser warning sign.
SAFETY INFORMATION 2
8022447/0000/2018-01 | SICK O P E R A T I N G I N S T R U C T I O N S | GM700 13
Subject to change without notice

Figure 2: Laser sign for HF measurement
Figure 3: Laser sign for NH3 measurement
Figure 4: Laser sign for HCI measurement
2 SAFETY INFORMATION
14 O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice

2.3 Intended use
The device serves exclusively for emission and process monitoring of gases in industrial
plants.
The device measures continuously directly in the gas duct (in-situ).
2.4 Responsibility of user
Designated users
see "Target groups (and document structure)", page 7.
Correct project planning
•Basis of this Manual is the delivery of the device according to the preceding
project planning (e.g., based on the SICK application questionnaire) and the rele‐
vant delivery state of the device (see delivered System Documentation).
wContact SICK Customer Service if you are not sure whether the device corre‐
sponds to the state defined during project planning or to the delivered system
documentation.
Special local conditions
In addition to the information in these Operating Instructions, follow all local laws, tech‐
nical rules and company-internal operating directives applicable wherever the device is
installed.
Read the Operating Instructions
bRead and observe these Operating Instructions.
bObserve all safety instructions.
bIf anything is not clear: Please contact SICK Customer Service.
Document retention
bMust be kept for reference.
bMust be passed on to new owners.
SAFETY INFORMATION 2
8022447/0000/2018-01 | SICK O P E R A T I N G I N S T R U C T I O N S | GM700 15
Subject to change without notice

3 Product description
3.1 Product identification
Product name GM700
Device version Measuring Probe Version
Manufacturer SICK AG
Erwin-Sick-Str. 1 · D-79183 Waldkirch · Germany
Type plates Measuring Probe Version
•Sender/receiver unit: On right side
•On purge air fixture: On tube
3.2 Product characteristics
■The device serves for continuous measurement of gas concentrations in industrial
plants
■For application with high water ratios, i.e. waste incineration, we offer a specific
version, the GM700-04 or GM700-07.
■The device is an in-situ measuring system which means measuring is done directly
in the gas carrying duct
■Measuring components: HF, HCI, NH3, NH3 + H2O, HCI + H2O
■Measuring principle: Diode laser spectroscopy (TDLS)
3.3 Device variants
Variants Measured components
GM700-02 HF
GM700-03 HCI
GM700-04 NH3, high humidity
GM700-05 NH3
GM700-07 NH3 / H2O, high humidity
GM700-08 HCI / H2O
GM700-09 NH3 / H2O
3.4 Options
•Terminal box: For CAN bus with 24 V power supply.
The optional terminal box is available for distances between SR-unit and EvU >4
meters via a CAN bus cable provided by the customer.
•Cover plate: For the purge air fixture of the SR-unit.
To maintain purge air supply in cases where this must remain in operation at the
measuring point when the SR-unit is dismounted.
•Weatherproof cover: Required for installation outdoors
•Air heater for purge air supply: For special application conditions to prevent con‐
densate. An air heater is required when the difference between gas temperature
and dew point temperature is too small. The following practical rule of thumb
serves as guideline:
Gas temperature [°C] – dew point temperature [°C] < abs. humidity [Vol.-%].
Values are compared without considering the units of measure.
3 PRODUCT DESCRIPTION
16 O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice

3.5 Layout and function
12 3
1
45
6
6
Figure 5: GM700 layout (version representation)
1Sender/receiver unit GM700 (SR-unit)
2Purge air fixture
3Flange with tube
4Evaluation unit
5Purge air unit
6CAN lines
Function
•The device serves for continuous measurement of gas concentrations in industrial
plants.
•The device is an in-situ measuring system which means measuring is done directly
in the gas carrying duct.
•Measuring components: see "Device variants", page 16.
•Measuring principle: Diode laser spectroscopy (TDLS) (laser protection class 1).
•To safeguard measuring reliability, a permanent air flow (optics purge air) keeps
the optics free from soot and dust particles.
3.6 Purge air unit
•This protects the front window of the SR-unit and the reflector in the measuring
probe against contamination and high gas temperatures
•The purge air is blown into the gas duct through the “flange with tube”.
NOTE
Further information on the purge air unit, see Operating Instructions of the purge air
unit.
PRODUCT DESCRIPTION 3
8022447/0000/2018-01 | SICK O P E R A T I N G I N S T R U C T I O N S | GM700 17
Subject to change without notice

3.7 Check cycle
Cyclic check cycle for zero and sensitivity checks
Start a check cycle via
•Timer trigger: Configurable 0 ... 1440 minutes (= 1 day), see menu “Settings /
Check Cycle”
•External digital input signal (Di 1)
Purpose of check cycle
■Checking the zero point and span point without feeding span gases.
Check cycle procedure
The measuring sequence to determine the zero and check point is performed. The digi‐
tal input uses a falling edge for triggering, i.e. performance of a check cycle is sup‐
pressed as long as the signal is high (e.g., for control purposes).
Signaling
“Function control” (relay 3) is signaled per digital output during output of the zero and
check point.
Output
The output runs for 90 seconds each for the zero point followed by the check point.
•Unit and scaling for the current zero point according to the settings.
•Check or span point is displayed as percentage scaled to 70% of the measuring
range.
The same calculation method is used for the deviation as for the gas concentration with
the exception of correction factors which result from a gas adjustment as well as cus‐
tomer correction factors from menu PAR/SETTINGS / REGRESS. FUNCT. During the
check cycle output, the zero and span point are displayed in the lower display line paral‐
lel to the analog output. These can be viewed in menu DIAG/CHECK VALUES/<GAS> for
subsequent checks. Prerequisite is that the output has already been made via an ana‐
log output.
Deviations
A warning message is output, e.g., “AO1 NH3 ZEROPoint” when the zero or check point
deviation is above 2% of the upper display limit of an analog output.
The warning message remains until the next check cycle output is within the tolerance.
3.8 GMP and GPP measuring probes
The measuring probe included in the scope of delivery was defined during project plan‐
ning in accordance with the application requirements.
This Table shows an overview of the features of the different measuring probes. All
measuring probe versions are compatible with all SR-units. The SR-unit is calibrated to
the respective probe length before delivery.
Table 3: Measuring probes
Measuring probe GMP (open measuring probe) GPP (for dry gases)
Version Measuring path open in flow
direction; purge air guidance
with outlet aligned 90° to gas
flow
Gas diffusion probe with
ceramic filter, for dry sample
gas
3 PRODUCT DESCRIPTION
18 O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice

Measuring probe GMP (open measuring probe) GPP (for dry gases)
Max. gas temperature 250°C 430°C
Gas test according to EPA reg‐
ulation
No Yes
Purge air supply required Yes No
Optical interface heating in
measuring probe
No Yes, with integrated control
Sample gas flow velocity 1 ... 40 m/s < 40 m/s
Suitable for wet sample gas Yes No
Maximum duct pressure ±120 hPa, depending on
purge air supply
±120 hPa
Measurable components NH3, HF, HCl NH3, HCl
System response time (T90) > 5 s > 120 s
Duct diameter > 360 mm > 300 mm
Dust concentration < 2 g/m3 in operating state < 30 g/m3 in operating state
Probe lengths available "Dimension drawings, open measuring probe (GMP)",
page 84 and "Dimension drawings GPP measuring probe
(Gas Permeable Probe)", page 85.
Active measuring paths avail‐
able [mm]
250/500/750/1000/1250 250/500/750/1000
3.8.1 GMP measuring probe in detail
pen Close
2
5
7
6
4
3
1
4
Figure 6: GMP measuring probe description
1Reflector unit
2PT1000 temperature sensor
3Purge air outlet: Air outlet in the duct 90° to gas flow direction (directed purge air)
4Locking device for opening between measuring probe and SR-unit
5Light beam, sender-reflector
6Purge air connection
7CAN connection
PRODUCT DESCRIPTION 3
8022447/0000/2018-01 | SICK O P E R A T I N G I N S T R U C T I O N S | GM700 19
Subject to change without notice

3.8.1.1 Gas connection for sample gas sampling on purge air fixture of GMP measuring probe
For the reference measurement, sample gas can be extracted from the gas duct via a
gas sampling valve on the purge air fixture of the GMP measuring probe.
Figure 7: Gas sampling valve on the GMP measuring probe
1Gas sampling screw fitting
NOTE
The reference measurement is not part of maintenance tasks carried out by the cus‐
tomer.
3.8.2 GPP gas diffusion probe in dry or wet version
Project planning information: There are two versions of the GMP measuring probe that
differ in the filter used. This supports differing application areas regarding the moisture
content of the sample gas.
Characteristics
•Suitable for higher dust contents than the GMP probes.
•For EPA-conform audit measurement.
•For applications with low flow velocities or varying flow profiles.
Integrated sensors
•Temperature sensor PT 1000: Continuously measures the media temperature on
the active measuring path of the probe
•Pressure sensor
•The measured data are transferred via the CAN bus interface of the measuring
probe and can then be displayed on the evaluation unit.
Figure 8: GPP measuring probe description
1Reflector unit
3 PRODUCT DESCRIPTION
20 O P E R A T I N G I N S T R U C T I O N S | GM700 8022447/0000/2018-01 | SICK
Subject to change without notice