Siel Green Point User manual


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-11-19
Pag. 0 di 34 + FR

6-10 kVA UPS
INSTALLATION AND USER MANUAL
Green Point
KEEP FOR FUTURE REFERENCE
for the entire life of the appliance




IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 1 di 34 + FR

All rights reserved.
The information in this document is subject to change without notice.
Publish statement
Thank you for purchasing this series UPS.
This series UPS is an intelligent, single phase in single phase out, high frequency online
UPS designed by our R&D team who is with years of designing experiences on UPS. With
excellent electrical performance, perfect intelligent monitoring and network functions,
smart appearance, complying with EMC and safety standards, The UPS has become
standard product meets the world’s advanced level. Read this manual carefully before
installation
This manual provides technical support to the operator of the equipment


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 2 di 34 + FR

Safety Instruction
1. Prohibition
1.1 There is a high risk of electric shock from the UPS inside, so please do not open or
remove the casing or front panel unless it is operated by authorized technicians,
otherwise warranty becomes void as well.
1.2 Please contact and discuss with distributors before connecting the UPS to following
equipments
nMedical equipments which have direct relationship with patients’ life
nEquipments like elevators which may do harm to human being
nSimilar equipments as mentioned above
1.3 Don’t dispose of the battery with fire so as to avoid explosion
2. Safety notice
1) Output of standard UPS configured with internal batteries may be energized even if
the UPS input is not connected to the utility
2) Do disconnect the UPS input and make sure the UPS is complete off before moving
the UPS or reconfigurate the connection, otherwise there will be potential electric
shock.
3) For the sake of human being safety, please well earth the UPS before starting it.
4) Working environment and storage way will affect the lifetime and reliability of the
UPS. Avoid letting the UPS work under following environment for long time
nArea where the humidity and temperature is beyond the specified
range(temperature 0 to 40 celsius degree, relative humidity 5%-95%).
nDirect sunlight and location nearby heat
nArea which can be crashed easily
nArea with corrosive gas, flammable gas, excessive dust, etc.
5) Keep the ventilations in good conditions otherwise the temperature of components
inside UPS will be high and the component and UPS life will be affected.
6) It is forbidden to pour liquid or put any objects into the UPS.


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 3 di 34 + FR

7) Don’t use liquid extinguisher if there is a fire, a dry powder extinguisher is
recommended.
8) Battery life cycle will be shorter as environment temperature rise. Replacing battery
periodically can help to keep UPS in normal status and assure backup time required.
Battery replacement should be done by authorized technician.
9) Keep the UPS in a dry area or environment if it will not be free of operation for long
time. Storage temperature of UPS with internal battery is -20ć~+55ć, extended
backup model without internal battery is -40ć~+70ć.
10) Taking out the UPS or batteries from storage, it is recommended to connect them
with the utility for at least 12 hours per 3 months to avoid battery over-draining
11) Don’t open the battery, electrolyte inside will do harm to eyes and skin. Please use
plenty of clean water to wash if touching and go to see a doctor


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 4 di 34 + FR

Contents
1. Product Introduction ...................................................................................................................... 6
1.1 Application.................................................................................................................................... 6
1.2 Product range ..............................................................................................................................6
1.3 System principle diagram........................................................................................................... 6
1.4 Features ....................................................................................................................................... 7
1.5 Product overview......................................................................................................................... 7
1.5.1 Product view......................................................................................................................... 7
1.5.2 LCD Operation instruction ..................................................................................................8
1.5.3 Display instruction ............................................................................................................. 12
1.5.4 Rear panel instruction ....................................................................................................... 14
2 Installation........................................................................................................................................ 16
2.1 Unpack checking....................................................................................................................... 16
2.2 Installation procedure ............................................................................................................... 16
2.2.1 Installation note.................................................................................................................. 16
2.2.2 Installation........................................................................................................................... 17
2.3 Connection of parallel system ................................................................................................. 19
3. Operation......................................................................................................................................... 20
3.1 Working modes ......................................................................................................................... 20
3.1.1 AC mode ............................................................................................................................. 20
3.1.2 Bypass mode...................................................................................................................... 20
3.1.3 Battery mode ...................................................................................................................... 20
3.1.4 ECO mode .......................................................................................................................... 21
3.2 Operation .................................................................................................................................. 21
3.2.1 Power on............................................................................................................................. 21
3.2.2 System parameter setting ................................................................................................ 21
3.2.3 Start ..................................................................................................................................... 21
3.2.4 Inverter shutdown .............................................................................................................. 22
3.2.5 Power off............................................................................................................................. 22
3.3 Working Mode and transferring............................................................................................... 23
3.3.1 Transfer to bypass if overload ......................................................................................... 23
3.3.2 Normal mode to battery mode ......................................................................................... 23
3.3.3 Go to Bypass mode due to over temperature ............................................................... 23
3.3.4 Output short circuit ............................................................................................................ 23
3.4 UPS monitoring ......................................................................................................................... 23
3.5 LCD operation menu ................................................................................................................ 24
3.5.1 Main menu switching......................................................................................................... 24
3.5.2 Submenu switching........................................................................................................... 24
3.5.3 Priority of info displayed on LCD .................................................................................... 24


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 5 di 34 + FR

4. Maintenance ................................................................................................................................... 25
4.1 Fan maintenance ...................................................................................................................... 25
4.2 Battery maintenance................................................................................................................. 25
4.3 Visual checking ......................................................................................................................... 25
4.4 UPS status checking ................................................................................................................ 26
4.5 Function checking ..................................................................................................................... 26
5 Trouble shooting ............................................................................................................................ 26
Appendix 1. USB communication ................................................................................................. 28
Appendix 2. RS232 communication port definition .................................................................. 29
Appendix 3. Specification................................................................................................................ 30
Appendix 4. Options ......................................................................................................................... 32
Appendix 5. UPS message table.................................................................................................... 33


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 6 di 34 + FR

1. Product Introduction
1.1 Application
This series UPS providing reliable AC power to various equipment, can be used for
computer center, network management center, auto control system, telecom
systems, etc
1.2 Product range
Capacity
6kVA 10kVA
Model
6kVA S
6 kVA H
10kVA S 10kVA H
Remarks
with internal
battery
External battery
with internal
battery
External battery
1.3 System principle diagram
The system can work in single unit, and parallel so as to enhance the reliability.
Fig.1-1 Single unit


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 7 di 34 + FR

1.4 Features
This series UPS is newly introduced. It is an intelligent online sine wave UPS.
nHigh frequency, double conversion, high input power factor, wide input voltage
range, the output will not be disturbed by power network, suitable for area with
poor power supply condition
nDSP technology for all-digital control, high reliability, self-diagnostics and
protections are featured
nIntelligent battery management which extends battery life
nLCD panel and LED indicators clearly indicate the system status and
parameters such as input/output voltage, frequency, load, temperature inside
UPS, etc.
nPerfect network power management can be achieved by using UPS
monitoring software
nMaintenance bypass switch is provided so the power supply to load will not be
interrupted during repair
nFriendly maintenance module design, easy for maintenance.
1.5 Product overview
1.5.1 Product view
F1-2 Complete unit view


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 8 di 34 + FR

1.5.2 LCD Operation instruction
The LCD control panel which consists of LCD display board, LED and buttons, (see
Fig1-3) displays and controls these information including operating information, alarm
information, function setting information.
nLCD control panel
1) Five green LED and one red LED
2) LCD control panel which can display four line of English
3) Button: On, Off, ESC, Enter, and Left ,Right
21
2FF
(6&
ENT
%<3$66
RECT INV OUTPUT
FAULT
Fig.1-3 LCD control panel introduction
1. LCD Display Board
2. ESC
3. Off button
4. On button
5. right or down
6. Enter/Save
7. left or up
8. Output Indicator
9. Inverter Indicator
10. Battery Indicator
11. Mains (AC) Indicator
12. Bypass Indicator
13. Fault Indicator


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 10 di 34 + FR

nLED indicator definition
1) Fault IndicatorδredεφOn indicates when a fault occurred; Off means no fault
2) IndicatorδGreenεφOn means AC is normal, Off means AC is not present,
blinking means voltage is beyond normal range
3) Inverter IndicatorδGreenεφOn : when load is powered by inverter, Off : when it
is not working, blinking: when overload
4) Bypass IndicatorδGreenεφOn : when UPS is in bypass mode, Off: not in bypass
mode; blinking: when the input is beyond normal range
5) Battery IndicatorδGreenεφOn: when UPS is in battery mode, Off : Not in Battery
mode; Blinking: when battery voltage is low or battery is not connected
6) Output IndicatorδGreenεφOn: when there is output, Off: no output.
nLCD display content
1) Running parameters
Input voltage/frequency, output voltage/frequency/current/loading, output power,
inverter voltage, battery voltage/battery remaining capacity, Bus voltage/bus
running time, temperature inside UPS
2εAlarm information ( priority from high to low )
It provides shutting down, auxiliary power fault, output short circuit, inverter fault,
rectifier fault, over temperature, overload, charger fault, battery fault, battery
capacity low, ready to shut down and output fault.
3εParameter setting
Menu setting, working mode setting, battery capacity setting, ID of parallel UPS,
output voltage/frequency level, bypass voltage range, Buzzer enable
lBoosting charging voltage 2.30 to 2.35V per cell, floating charging voltage
2.20 to 2.29V per cellδuse PC to settingε
lBattery capacity setting includes the Ah of each battery unit, battery quantity
16 to 20, parallel group number
lParallel setting
lUPS ID setting
lUPS amount setting


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 11 di 34 + FR

nButton definition
Button
Definition
ON
Switch on the inverter by pressing and holding it for
1s when the UPS is off
OFF
Switch off the inverter output by pressing and holding
it for 1s when the UPS is
on, load
will be powered by
bypass output if the bypass is normal
ENT
Confirm the operation
ESC
cancel and go to previous menu
ۆ
Turn to another menu or parameter
ڼ
Turn to another menu or parameter
nUPS Messages reference table
Explanation
Content
Initialization
CurState: Init
No output
No-Out
At bypass
Bypass
Rectifier working
Mains
Battery mode
Battery
Battery testing
Testing
Starting
Starting
ECO mode
CurState: ECO
EPO mode
CurState: EPO
UPS maintaining
CurState: M-Byp
UPS fault
CurState: Fault
Battery float charging
Battery Charging
Battery Boost charging
Battery Boost
Inverter on/off
Inverter ON/ Inverter OFF
Master of UPS
Inver Master
Maintenance switch close or open
SWMB ON/ SWMB OFF


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 12 di 34 + FR

1.5.3 Display instruction
1) The main interface below comes out when the power is connected or the system is
cold start. See Fig1
Fig.1φMain interface
2) Press ESC/ ۆor ڼbutton, it will change to the basic status interface , see
Fig2 below
Fig.2φBasic status interface
3) Press the ENT button, it will change to main menu, see Fig3,
Fig.3φMain menu
4) An arrow icon will come out on the LCD when pressing the ENT, then the data info,
status info, setting info can be selected by pressing the right or left arrow button, and
checking the details by pressing
5) Select and confirm the data info to be viewed in detail. It contains the details of the
AC input /output, inverter, battery, BUS, parallel, temperature. See Fig 4 to 12 below.
Fig.4φMAIN INPUT INFO Fig.5φOUTPUT INFO Fig.6φOUTPUT INFO


.9$
),*85(
%DWWHU\φ$+
9LQ9
+=
9RXW9+=


),*8(5
67$786
6(77,1*
),*85(
0DLQV

9+]


),*85(
2XWSXW
9$

+]/RDG

),*85(
2XWSXW
.:.9$



IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 13 di 34 + FR

Fig.7φINVERTER INFO Fig.8φBATTERY INFO Fig.9 BATTERY INFO
Fig.10φBUS INFO Fig.11φPARALLEL INFO Fig.12φTEMPERATURE
INFO
6) Select and confirm the status info can view the details, including status information,
alarm information, code, power rating and version. See Fig 13 to 14
Fig.13φmain menu Fig.14φmain menu
7) Select and confirm setting menu, setting information will be displayed on the screen,
which includes user set, system set, parallel set, battery sett, revise set. See Fig 15
to 19
Fig.15φsetting menu Fig.16φsetting menu
Fig.17φsetting menu Fig.18φsetting menu
),*85(
,QYHUW
9+=



),*85(
3%DWWHU\
9$
PLQ
),*85(
1%DWWHU\
9$
PLQ


),*85(
%86
99

&$3φ+RXU
),*85(
3DUDOOHO
,'
3ϫ$PRXQWφ

67$786
&RGHφ

)DXOWφ

0RGHOφ.9$


67$786
9HUVLRQ
9%'
6(77,1*
0RGHφ125
%DWWQXPφ
%DWWFDSφ$+
6(77,1*
9/HYHOφ9
)/HYHOφ+]

6(77,1*
9XSSHU
9ORZHU

),*85(
7HPSHUDWXUHđ
3)&,19

(19

6(77,1*
%X]]HUφ(QDEOH


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 14 di 34 + FR

Fig.29φParallel setting
1.5.4 Rear panel instruction
1.5.4.1 6 kVA H/S rear panel
Fig.1-4 Rear Instruction
1. Parallel slot
2. Maintenance bypass switch (covered)
3. Intelligent slot
4. EPO
5. COM
6(77,1*
3DUDOOHOVHW
,'
3DPRXQW
35HGXQG



IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 15 di 34 + FR

6. USB
7. Input switch
8. Input/output/battery terminalδcoveredε
1.5.4.2 10 kVA H/S rear panel

1. Parallel slot
2. Maintenance bypass switch (covered)
3. Intelligent slot
4. EPO
5. COM
6. USB
7. Input switch
8. Input/output/battery terminalδcoveredε


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 16 di 34 + FR

2 Installation
2.1 Unpack checking
1) Don’t lean the UPS when moving it out from the packaging.
2) Check the appearance to see if the UPS is damaged during transportation, do
not switch on the UPS if any damaged is found and please contact the dealer.
3) Check the accessories according to the packing list and contact the dealer if
found any parts missing
2.2 Installation procedure
2.2.1 Installation note
* Put the UPS at flat place next to the equipment.
* Keep the UPS at least 20cm from wall or equipment or other object. Don’t block
the ventilation holes of the UPS located in the front panel and the bottom part, so as
to *keep the ventilation in good conditions; avoid temperature of components inside
getting high.
* Keep the UPS away from high temperature, water, flammable gas, corrosive gas,
dust, direct sunlight and explosive things
* Don't lay the UPS outdoor
* 63A circuit breaker is required at the input L-N for 6KVA UPS, while 100A for the
10KVA UPS.
* PDU is required to connect to the UPS output so as to weaken the affection
between loads
* In order to fix the UPS, please lock its wheels by shifting the sheet on each wheel
* RCD load like computer, linear load and small inductive load can be connected
with the UPS. Please contact dealer if other types of loads is required to be
connected with
* For the safe of user and equipments, please betake correct power configuration
Fig.2-1 Correct power configuration


IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 17 di 34 + FR

2.2.2 Installation
nExternal battery connection (for extend model only )
1) The breaker on battery cabinet should be off.
2) Connect battery with positive pole, common pole and negative pole to battery
connector (BAT+,BATN,BAT-, don’t reverse battery polarity.
3) Make sure battery quantity complies with the specs. Measure the voltage of
battery bank after finishing connection and the battery voltage should be around
192/216/240Vdc. measure positive and negative battery voltage should be
around 96/108/120VdcȾDon’t mix batteries with different capacity,
manufacturers and don’t mix brand new and old batteries, either.
CAUTION
It is recommended to connect or replace battery after switching off the
system; don’t reverse battery polarity when doing battery hot-swapping.
nUPS input and output connection
Minimum 10AWG copper wires are required for the 6KVA, and 8AWG for 10KVA,
including input/output cables, battery cables.
1) Switch off all breakers before connecting cables
2) Remove the cover of the terminals, see Fig 2-2,following it to connect the cables



IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 18 di 34 + FR

Fig.2-2I/O terminals connection
3) Connect the UPS output L, N, E to L, N, E of load via a PDU. Tighten the screws
and shelter the terminals
WARNING
έ
Please connect the output Earth well before go for other operation
nConnection of the UPS communication cables
1) USB cable provided in accessories can be used to connect the UPS with PC
2) Follow steps below to install SNMP (if purchased )φ
A. Remove the cover of SNMP slot at UPS rear panel and keep it for further use.
B. Insert the SNMP card and tighten the screws
C. Connect the UPS with internet by network cable.
D. Refer to the SNMP manual provided to do SNMP setting
CAUTION
Termina
tors are required so as to ensure the connections are firm
Don’t reverse the input L and N
Don’t connect the UPS input to a wall outlet or the outlet will get burnt.



IV394E Rev. 00
Installation and user manual
Date of issue: 2015-12-11
Pag. 19 di 34 + FR

2.3 Connection of parallel system
Parallel
cable
Parallel
cable
Parallel
cable
UPS1 UPS2 UPS4
UPS3
Fig.2-3 parallel system
Make sure all the breakers are off and no output at the UPS output.
Extended connecting cables in Parallel:
When the UPS are connected in parallel, the copper wires required to connect with
each UPS is minimum 10AWG for the 6KVA and 8AWG for 10KVA, but the main
wire for linking all the UPS in parallel should be N* 10AWG or 8AWG (N refers to the
number of the UPS in parallel.)
Make sure the cables are as shorter as possible to reduce any possible noise
interference to data transfer.
CAUTION
Connect the L,N and E well
Configurate individual battery bank for each extend backup UPS in
parallel system. Also can be use common battery bank.
