Siemens QMX3.P30 User manual

CM2N1602en_07
2017
-05-22
Building Technologies
s
1602
QMX3.P37 QMX3.P34 / P74 QMX3.P02 QMX3.P70 QMX3.P30 / P40
Desigo™ TRA
QMX3.P30
Q
MX3.P40
QMX3.P70
QMX3.P02
QMX3.P34
QMX3.P74
QMX3.P37
Wall-mounted sensors and room
operator units for KNX
PL-Link,
KNX S
-mode and KNX LTE-Mode
Communicative sensors, switches and room operator units with KNX (S-mode,
LTE-Mode) or KNX PL-Link (for Desigo™ Total Room Automation)
Functions (depending on type):
•Energy efficiency function ("Green Leaf ")
•Room temperature, CO2, and humidity measurement
•Control of light, blinds, and scenes
•PID controller for room temperature or ventilation (KNX S-mode)
•LCD Display for room temperature, operating mode, etc.
•Label for light, blinds and scenes (exchangeable, created with Word
template)
•Operation via 8 or 16 touchkeys
•Interface KNX (S-mode, LTE-Mode) and KNX PL-Link(for TRA, with plug &
play functionality)
•Powered over KNX PL-Link / KNX bus
•LEDs to indicate the switch state or the position of the device in dark rooms

2 / 16
QMX3... Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode CM2N1602en_07
Siemens Building Technologies 2017-05-22
Product number Stock number Features
Temperature sensor Humidity sensor CO2sensor Air quality indicator with LED Segmented backlit display and
t hk
"Green Leaf" LED Configurable touch- keys with LED
di l
Window for labels
Sensors
QMX3.P30
QMX3.P30-1BSC
S55624-H103
S55624-H123
X
QMX3.P40
QMX3.P40-1BSC
S55624-H116
S55624-H124
X X
QMX3.P70
QMX3.P70-1BSC
S55624-H104
S55624-H125
X X X X
Room
operator
units
QMX3.P02
QMX3.P02-1BSC
S55624-H107
S55624-H128
X X X
QMX3.P34
QMX3.P34-1BSC
S55624-H105
S55624-H126
X
X
X
QMX3.P74
QMX3.P74-1BSC
S55624-H106
S55624-H127
X X X X X
QMX3.P37
QMX3.P37-1BSC
S55624-H108
S55624-H129
X X X X X
Accesso-
ries
QMX3.MP1 S55624-H110 Base plate for conduit box / cavity wall box for
68 mm diameter hole
20 pcs. per package
Use / compatibility
The room automation station determines the functions of both LCD display and
keys.
•Measure and indicate the room temperature, humidity and CO2.
•Operatethe room functions.
•Indicate external information
(outdoor temp., outdoor humidity, state of a window switch).
Measure and indicate Indicate external information
−the room temperature – outdoor temperature
−the relative humidity – outdoor humidity
−the CO2concentration – state of a window switch
Control (threshold value switch) Control (with a PID controller)
−of the relative humidity – of the room temperature
−of the CO2concentration
Use with KNX PL-Link
Use with KNX S-mode

3 / 16
QMX3... Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode CM2N1602en_07
Siemens Building Technologies 2017-05-22
Switches
−switching and dimming of lights
−control of blinds
−selecting and saving of scenes
LTE can only use the sensor information of the types QMX3.P30, QMX3.P40, and
QMX3.P70.
Devices with CO2measurement are not suitable for safety applications such
as gas or smoke alarm.
Mechanical design
•The devices are designed for wall-mounting (A). A conduit box is optional.
−Conduit box: Keep in mind the dimensions of the conduit box!
−Cable conduits on the wall: Keep a distance of 30 mm (from above) /
20 mm (from below) to the base plate (B), so that the device (C) can be
snapped onto the base plate.
•The base plate (B) has screw holes for all common flush-mount boxes.
The screw head height must not exceed 3 mm.
•The device (C) incorporates a KNX / PL-Link plug, a tool plug, and, depending
on the type, sensor element, keys, LCD panel, window for the label.
The cable can be pushed into channels on the rear.
•A KNX plug is enclosed with the devices
The optional metal-reinforced base plate QMX3.MP1 (B1) serves for two purposes:
•It is more rigid so that it does not bend when fixed in the middle with two screws
only (directly over a conduit box or a cavity wall box).
•It has a removable gray foam plate (B2) for mounting on a 68 mm diameter
cavity wall box. The plate compensates for the jutting edge of the box (see
mounting, page 5).
QMX3.MP1 is supplied in boxes with 20 pcs.
1602J01_01
B
C
A
B2
B1
Use with KNX S-mode
(continued)
Use with
KNX LTE-Mode
NOTICE
Note

4 / 16
QMX3... Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode CM2N1602en_07
Siemens Building Technologies 2017-05-22
Engineering notes
•The room operator units offer plug & play functionality.
•The room operator units receive their power from the connected room
automation station via the KNX PL-Link interface.
•KNX PL-Link supports plug & play functionality for pre-configured devices out of
the library
•For KNX PL-Link wiring (topology, allowed cables and cable length), see the
Desigo installation guide, CM111043.
•Normally, electrical installers only install the base plate and the KNX PL-Link
plug.
•Use the tear-off label with the barcode on the packaging / on the display and
stick it on the floor plan to prepare commissioning for several room operator
units per room automation station.
The same barcode label with unique identifier is available on the device.
Engineering and commissioning is done using the ETS tool
For detail information see Technical basics, P1602.
Engineering and commissioning is done using the ACS tool.
For detail information see Technical basics, P1602.
•The ABT provides a list of the devices, their function and their location
•Create the labels using a Word template (M1602.1)
•Print the labels on commercially available overhead transparency film
•Cut out the labels
•Insert or exchange the labels as described in the mounting instructions, M1602.
Mounting and installation
•The devices are suitable for wall mounting.
•Recommended height: 1.50 m above floor.
•Do not mount the devices in recesses, shelves, behind curtains or doors, or
above or near heat sources.
•Avoid direct solar radiation and drafts.
•Seal the conduit box or the installation tube, as air currents can affect sensor
readings.
•Adhere to allowed ambient conditions.
•Mounting instructions M1602 are enclosed with the devices.
KNX PL-Link
KNX S-mode
KNX LTE-Mode
Labels for switches
(QMX3.P02, P37)
Location (sensors,
room operator units)
Mounting instructions

5 / 16
QMX3... Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode CM2N1602en_07
Siemens Building Technologies 2017-05-22
Service LED (red) Tool plug Programming pin
*) The installing tube must be sealed or cold or warm air may enter the device and cause faulty
temperature readings by the internal sensor.
Use a metal-reinforced base plate QMX3.MP1 instead oft he standard base plate
delivered with the room operator unit.
The installing tube must be sealed or cold or warm air may enter the device and cause faulty
temperature readings by the internal sensor.
1Fixing the box on the cavity wall.
2Fixing the QMX3.MP1 base plate on the box using 2 screws.
3The gray foam plate (removable) compensates for the jutting edge of the box so that the plate
is aligned with the wall.
2602J02
*)
Mounting over a
conduit box
Monting over a cavity
wall box
1602J108
1
1
2
2
3

6 / 16
QMX3... Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode CM2N1602en_07
Siemens Building Technologies 2017-05-22
Wall mounting
Remove the breakout on the housing before putting the cable into the gaining channel.
4-wire cables
(daisy chain wiring)
Remove the cable coating, as it will not fit in
the gaining channel.
Cable ducts on the wall
30 mm
Keep a distance of 30 mm (from above) /
20 mm (from below) to the base plate,
so that the device can be snapped onto the
base plate.
Dismounting / service:

7 / 16
QMX3... Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode CM2N1602en_07
Siemens Building Technologies 2017-05-22
Sample icons are available in the label
template M1602.1
Information. e.g. on room operator unit
location or on room type (free text)
•For KNX PL-Link wiring (topology, allowed cables and cable length), see the
Desigo TRA installation guide, CM111043.
•Use the correct cables for the KNX PL-Link bus
•Do not interchange the wires of the KNX PL-Link cable.
– The red terminal is for KNX PL-Link +
– The gray terminal is for KNX PL-Link –
•For KNX S-mode follow the KNX regulations
•Observe all local installation regulations.
Caution!
•The devices are not protected against accidental connection to AC 230 V.
Max.6
59.2 ±0.15
1602z110
54 ± 0.15
Labels for QMX3.P02,
QMX3.P37
Insert label
Remove label
Installation
1602Z106
1602J109
1602J110
1602Z107

8 / 16
QMX3... Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode CM2N1602en_07
Siemens Building Technologies 2017-05-22
Prerequisite for commissioning (KNX PL-Link)
The room automation station must be running and an application must be loaded.
The application is not loaded on the room operator unit, but the room automation
station.
Download of the application is done using the SSA-DNT (Pack & Go) or the ABT.
For this purpose (or for service), connect the ABT to the room automation station
(USB or Ethernet).
Manual commissioning (KNX PL-Link)
All commissioning work is done via the room automation station, using the SSA-
DNT or the ABT.
The ABT is never connected directly to a room operator unit.
Addressing
When more than one QXM3.P... room operator unit is on the same trunk of the
KNX PL-Link bus, manual commissioning is done as follows:
1. Connect the SSA-DNT or the ABT to the room automation station and activate
the online commissioning function.
2. Load the web page "KNX PL-Link identification".
Activate the identification function.
The room automation station now waits for a signal from the room operator
unit.
3. On the room operator unit, simultaneously press the upper left and bottom
right button for at least 5 seconds (keys 1 and 8).
4. The "Engineering" page is displayed.
5. Press "Prog. Mode" (Key 2).
The display changes from "DISA" to "EnAB".
The tool identifies the current room operator unit that is operated and assigns
it.
6. After the device is commissioned, reset the device to programming mode to
“disabled” by pressing key 2.
Note: Programming mode resets to “disabled” each time the device restarts.
Connection test
1. Press "Conn. Test" (key 3) to test the KNX PL-Link connection.
The display shows the result of the connection test:
2. Press key 8 to return to the engineering page.
Reset to factory setting
Press "Fact. Reset" (Key 4). The device is locked and reboots within 10 seconds.
The room automation station deletes it from its device list. During this time, it is
safe to remove the device from the network.
If the bus plug remains connected, the device acts like a newly inserted device
requiring again automated or manual configuration.
Note! This operation resets all user preference data and
configuration settings to factory default.
This operation is irreversible.
Load application on the
room automation
station

9 / 16
QMX3... Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode CM2N1602en_07
Siemens Building Technologies 2017-05-22
Manual commissioning (KNX PL-Link, without display)
The devices are equipped with a programming pin and a red service LED on the
back side (see page 4)
1. Short press the programming pin (<0.5 s).
The device goes into programming mode; the service LED is continuously on.
The tool identifies the current room operator unit that is operated and assigns it.
2. After the device is commissioned, deactivate the programming mode by shortly
pressing the programming pin (<0.5 s). The service LED goes off.
Note: Programming mode resets to “disabled” each time the device restarts.
1. Medium press the programming pin (>2 s and <20 s) to test the KNX PL-Link
connection. After releasing the programming pin, the test of the KNX PL-Link
connection starts; the service LED flashes (1/4 s on, 7/4 s off).
After approx. 10 s, the test result is displayed:
– If the test is positive, the LED goes on continuously.
– If the test fails, it flashes (1 s on, 1 s off).
2. Short press the programming pin (<0.5 s) to stop displaying the result of the
connection test. The service LED goes off.
Long press the programming pin (>20 s). The device is locked and reboots within
10 seconds. The room automation station deletes it from its device list. During this
time, it is safe to remove the device from the network.
Note: there is no LED activity during this operation.
If the bus plug remains connected, the device acts like a newly inserted device
requiring again automated or manual configuration.
This operation resets all user preference data and configuration settings to
factory default.
This operation is irreversible.
Addressing
Connection test
Reset to factory setting
NOTICE

10 / 16
QMX3... Wall-mounted sensors and room operator units for KNX PL-Link, KNX S-mode and KNX LTE-Mode CM2N1602en_07
Siemens Building Technologies 2017-05-22
Commissioning (plug & play, KNX PL-Link)
When only one device is connected to the KNX PL-Link bus, the room operator
unit automatically establishes communications with the room automation station,
from where the functions are downloaded to the room operator unit (plug & play).
The following routine is executed:
Step With
display
Description
1
The Build number and the version number of the device are
displayed.
2
The Individual Address (IA) is downloaded to the device via
KNX PL-Link.
This step is skipped if the device is already configured.
Note: The configuration file can be downloaded any time; as a
result, these characters are displayed every time the room
automation station initializes download.
3a
After startup, the device goes to normal operation
(example view; picture depends on application in room
automation station).
3b
When configuration is faulty, "UCFG" is displayed, along with
the temperature that is measured by the local temperature
sensor.
In this case, manual commissioning must be performed (see
above).