Siemens SITRANS TS100 Administrator guide

___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SITRANS
Temperature sensors
TS100/TS200/TS300/TS500/TSinse
rt/TSthermowell
Compact Operating Instructions
01/2018
A5E03920348
-AE
Introduction
1
Safety notes
2
Description
3
Installing
4
Connecting
5
Commissioning
6
Service and maintenance
7
Technical data
8
Dimension drawings
9
Appendix
A

Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E03920348
Ⓟ
03/2018 Subject to change
Copyright © Siemens AG 2018.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Compact Operating Instructions, 01/2018, A5E03920348-AE 3
Table of contents
1 Introduction............................................................................................................................................. 7
1.1 Purpose of this documentation .................................................................................................7
1.2 Scope of this documentation ....................................................................................................7
1.3 Document history ......................................................................................................................8
1.4 Checking the consignment .......................................................................................................8
1.5 Security information ..................................................................................................................9
1.6 Transportation and storage.......................................................................................................9
1.7 Notes on warranty...................................................................................................................10
2 Safety notes.......................................................................................................................................... 11
2.1 Preconditions for use ..............................................................................................................11
2.1.1 Laws and directives ................................................................................................................11
2.1.2 Conformity with European directives ......................................................................................12
2.2 Improper device modifications ................................................................................................12
2.3 Requirements for special applications ....................................................................................13
2.4 Use in hazardous areas..........................................................................................................13
2.4.1 Qualified personnel for hazardous area applications .............................................................13
2.5 Use in flameproof enclosures "d" and protection in enclosures "tb".......................................14
2.5.1 For SITRANS TS500 ..............................................................................................................15
2.5.2 For SITRANS TSinsert/TS100/TS200/TS500 ........................................................................16
3 Description............................................................................................................................................ 17
3.1 Overview .................................................................................................................................17
3.2 Application ..............................................................................................................................18
3.3 Functional principles ...............................................................................................................18
3.4 Nameplate structure................................................................................................................18
3.5 Temperature transmitter for SITRANS TS500........................................................................19
3.6 Measuring inserts for SITRANS TS500 ..................................................................................20
3.7 Connection heads for SITRANS TS500 .................................................................................21
4 Installing ............................................................................................................................................... 23
4.1 Basic safety notes...................................................................................................................23
4.1.1 Installation and location requirements ....................................................................................24
4.1.2 Proper mounting .....................................................................................................................25
4.2 Install.......................................................................................................................................27
4.3 Install SITRANS TS300 Clamp-on..........................................................................................29

Table of contents
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
4Compact Operating Instructions, 01/2018, A5E03920348-AE
4.4 Disassembly........................................................................................................................... 30
5 Connecting ........................................................................................................................................... 31
5.1 Basic safety notes.................................................................................................................. 31
5.1.1 For SITRANS TSinsert........................................................................................................... 34
5.1.2 For SITRANS TSinsert/TS100/TS200/TS500........................................................................ 34
5.1.3 For SITRANS TS100/TS200.................................................................................................. 34
5.1.4 For SITRANS TS500 ............................................................................................................. 35
5.2 Electrical connection .............................................................................................................. 35
5.3 Electrical connection of resistance thermometers ................................................................. 36
5.4 Electrical connection of thermocouples ................................................................................. 37
5.5 Electrical connection of connectors ....................................................................................... 37
6 Commissioning ..................................................................................................................................... 39
6.1 Basic safety notes.................................................................................................................. 39
6.2 Commissioning....................................................................................................................... 40
7 Service and maintenance...................................................................................................................... 41
7.1 Cleaning ................................................................................................................................. 43
7.2 Return procedure ................................................................................................................... 43
7.3 Disposal ................................................................................................................................. 44
8 Technical data ...................................................................................................................................... 45
8.1 Rated conditions .................................................................................................................... 45
8.1.1 Maximum permissible ambient temperatures in the connection area of the sensor ............. 45
8.1.1.1 General limitations for compression fittings ........................................................................... 45
8.1.1.2 SITRANS TS100.................................................................................................................... 46
8.1.1.3 SITRANS TS500.................................................................................................................... 47
8.1.2 Maximum permitted sample temperatures within the process .............................................. 54
8.1.3 Measuring range .................................................................................................................... 56
8.2 Construction ........................................................................................................................... 56
8.3 Electrical data......................................................................................................................... 57
8.4 Measuring tolerances for resistance thermometers............................................................... 58
8.5 Measuring accuracy for thermocouples................................................................................. 59
8.6 Certificates and approvals ..................................................................................................... 60
8.6.1 SITRANS TSInsert/TS100/TS200/TS500.............................................................................. 60
8.6.2 SITRANS TS500.................................................................................................................... 62
9 Dimension drawings.............................................................................................................................. 65
9.1 Overview ................................................................................................................................ 65
9.2 SITRANS TS100.................................................................................................................... 69
9.3 SITRANS TS200.................................................................................................................... 70
9.4 SITRANS TS300.................................................................................................................... 71
9.5 SITRANS TS500.................................................................................................................... 75

Table of contents
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Compact Operating Instructions, 01/2018, A5E03920348-AE 5
9.5.1 SITRANS TS500, types 2 and 2N ..........................................................................................75
9.5.2 SITRANS TS500, types 2G and 2F ........................................................................................76
9.5.3 SITRANS TS500, type 3.........................................................................................................77
9.5.4 SITRANS TS500, types 3G and 3F ........................................................................................78
9.5.5 SITRANS TS500, types 4 and 4F...........................................................................................79
9.5.6 SITRANS TS500, type ST, threaded tapered well (7MC65..) ................................................81
9.5.7 SITRANS TS500, type SST, threaded tapered well (7MC55..) ..............................................82
9.5.8 SITRANS TS500, type SS, threaded straight well (7MC65..).................................................84
9.5.9 SITRANS TS500, type SS, threaded straight well (7MC55..).................................................85
9.5.10 SITRANS TS500, type SR, threaded reduced well (7MC65..) ...............................................86
9.5.11 SITRANS TS500, type SR, threaded reduced well (7MC55..) ...............................................87
9.5.12 SITRANS TS500, type FT, flanged tapered well (7MC65..) ...................................................88
9.5.13 SITRANS TS500, type FST, flanged tapered well (7MC55..).................................................89
9.5.14 SITRANS TS500, type FS, flanged straight well (7MC65..) ...................................................91
9.5.15 SITRANS TS500, type FS, flanged straight well (7MC55..) ...................................................92
9.5.16 SITRANS TS500, type FR, flanged reduced well (7MC65..)..................................................93
9.5.17 SITRANS TS500, type FR, flanged reduced well (7MC55..)..................................................94
9.5.18 SITRANS TS500, type SWT, socket tapered well (7MC65..).................................................95
9.5.19 SITRANS TS500, type SWST, socket tapered well (7MC55..) ..............................................96
9.5.20 SITRANS TS500, type SWS, socket straight well (7MC65..).................................................98
9.5.21 SITRANS TS500, type SWS, socket straight well (7MC55..).................................................99
9.5.22 SITRANS TS500, type SWR, socket reduced well (7MC65..)..............................................100
9.5.23 SITRANS TS500, type SWR, socket reduced well (7MC55..)..............................................101
9.5.24 SITRANS TS500 for installation in existing protective tubes................................................102
9.5.25 SITRANS TS500, type GP, general purpose, no well ..........................................................104
9.6 SITRANS TSinsert - measuring inserts for SITRANS TS500...............................................105
A Appendix............................................................................................................................................. 107
A.1 Certificates ............................................................................................................................107
A.2 Technical support..................................................................................................................107
Index................................................................................................................................................... 109

Table of contents
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
6Compact Operating Instructions, 01/2018, A5E03920348-AE

TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Compact Operating Instructions, 01/2018, A5E03920348-AE 7
Introduction
1
1.1
Purpose of this documentation
These instructions contain all information required to commission and use the device. Read
the instructions carefully prior to installation and commissioning. In order to use the device
correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it
electronically, configuring the parameters and commissioning it, as well as service and
maintenance engineers.
The temperature sensor has a modular design. If you integrate a transmitter or a display,
read the instructions of the transmitter and/or the display.
See also
Instructions and manuals (http://www.siemens.com/processinstrumentation/documentation)
1.2
Scope of this documentation
"7MC../7MT.." stands for:
Article nr.
Product
7MC71.. SITRANS TS100
7MC72..
SITRANS TS200
7MC80..
SITRANS TS300
7MC75..
SITRANS TS500 (European portfolio)
7MC65..
SITRANS TS500 (North American portfolio)
7MC55..
SITRANS TS500 (Asian portfolio)
7MC.01..
TSinsert
7MT..
TSthermowell

Introduction
1.3 Document history
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
8Compact Operating Instructions, 01/2018, A5E03920348-AE
1.3
Document history
The following table shows major changes in the documentation compared to the previous
edition.
The most important changes in the documentation when compared with the respective
previous edition are given in the following table.
Edition
Remark
01/2018
TSthermowell added
10/2016 Technical data for rated conditions changed
1.4
Checking the consignment
1. Check the packaging and the delivered items for visible damages.
2. Report any claims for damages immediately to the shipping company.
3. Retain damaged parts for clarification.
4. Check the scope of delivery by comparing your order to the shipping documents for
correctness and completeness.
WARNING
Using a damaged or incomplete device
Risk of explosion in hazardous areas.
•Do not use damaged or incomplete devices.

Introduction
1.5 Security information
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Compact Operating Instructions, 01/2018, A5E03920348-AE 9
1.5
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be
connected to an enterprise network or the internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit:
https://www.siemens.com/industrialsecurity
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customer’s exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://www.siemens.com/industrialsecurity.
1.6
Transportation and storage
To guarantee sufficient protection during transport and storage, observe the following:
●Keep the original packaging for subsequent transportation.
●Devices/replacement parts should be returned in their original packaging.
●If the original packaging is no longer available, ensure that all shipments are properly
packaged to provide sufficient protection during transport. Siemens cannot assume
liability for any costs associated with transportation damages.
NOTICE
Insufficient protection during storage
The packaging only provides limited protection against moisture and infiltration.
•Provide additional packaging as necessary.
Special conditions for storage and transportation of the device are listed in Technical data
(Page 45).

Introduction
1.7 Notes on warranty
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
10 Compact Operating Instructions, 01/2018, A5E03920348-AE
1.7
Notes on warranty
The contents of this manual shall not become part of or modify any prior or existing
agreement, commitment or legal relationship. The sales contract contains all obligations on
the part of Siemens as well as the complete and solely applicable warranty conditions. Any
statements regarding device versions described in the manual do not create new warranties
or modify the existing warranty.
The content reflects the technical status at the time of publishing. Siemens reserves the right
to make technical changes in the course of further development.
See also
Contacts (http://www.siemens.com/processinstrumentation/contacts)
SITRANS T product information (http://www.siemens.com/sitranst)
Instructions and manuals (http://www.siemens.com/processinstrumentation/documentation)

TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Compact Operating Instructions, 01/2018, A5E03920348-AE 11
Safety notes
2
2.1
Preconditions for use
This device left the factory in good working condition. In order to maintain this status and to
ensure safe operation of the device, observe these instructions and all the specifications
relevant to safety.
Observe the information and symbols on the device. Do not remove any information or
symbols from the device. Always keep the information and symbols in a completely legible
state.
Symbol
Description
Pay attention to the operat
ing instructions
2.1.1
Laws and directives
Observe the safety rules, provisions and laws applicable in your country during connection,
assembly and operation. These include, for example:
●National Electrical Code (NEC - NFPA 70) (USA)
●Canadian Electrical Code (CEC) (Canada)
Further provisions for hazardous area applications are for example:
●IEC 60079-14 (international)
●EN 60079-14 (EU)
SITRANS TSthermowell
The thermowell is affected by the static, dynamic and chemical load from the process
parameters including static and dynamic load, flow induced vortexes. This has influence on
the shape of the thermometer, stem diameter and insertion length.
Observe the test certification, provisions and laws applicable in your country during
connection, assembly and operation. These include:
●ASME PTC 19.3
●DIN 43772 Annex 1-2
●AD-directive
●VDI/VDE 3511-5

Safety notes
2.2 Improper device modifications
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
12 Compact Operating Instructions, 01/2018, A5E03920348-AE
In critical applications, a thermowell stress calculation is recommended:
●ASME PTC 19.3-TW2016
●Dittrich/Klotter-method engineering service
2.1.2
Conformity with European directives
The CE marking on the device symbolizes the conformity with the following European
directives:
Electromagnetic compatibi
l-
i
ty EMC
2014/30/EU
Directive of the European Parliament and of the Council on the
approximation of the laws of the Member States relating to elec-
tromagnetic compatibility and repealing Directive 89/336/EEC.
Atmosphère explosible
ATEX
2014/34/EU
Directive of the European Pa
rliament and the Council on the
approximation of the laws of the Member States concerning
equipment and protective systems intended for use in pote
ntial-
ly explosive atmospheres.
The applicable directives can be found in the EC conformity declaration of the specific
device.
See also
Certificates (Page 107)
2.2
Improper device modifications
WARNING
Improper device modifications
Risk to personnel, system and environment can result from modifications to the device,
particularly in hazardous areas.
•Only carry out modifications that are described in the instructions for the device. Failure
to observe this requirement cancels the manufacturer's warranty and the product
approvals.

Safety notes
2.3 Requirements for special applications
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Compact Operating Instructions, 01/2018, A5E03920348-AE 13
2.3
Requirements for special applications
Due to the large number of possible applications, each detail of the described device
versions for each possible scenario during commissioning, operation, maintenance or
operation in systems cannot be considered in the instructions. If you need additional
information not covered by these instructions, contact your local Siemens office or company
representative.
Note
Operation under special ambient conditions
We highly recommend that you contact your Siemens representative or our application
department before you operate the device under special ambient conditions as can be
encountered in nuclear power plants or when the device is used for research and
developm
ent purposes.
2.4
Use in hazardous areas
2.4.1
Qualified personnel for hazardous area applications
Qualified personnel for hazardous area applications
Persons who install, connect, commission, operate, and service the device in a hazardous
area must have the following specific qualifications:
●They are authorized, trained or instructed in operating and maintaining devices and
systems according to the safety regulations for electrical circuits, high pressures,
aggressive, and hazardous media.
●They are authorized, trained, or instructed in carrying out work on electrical circuits for
hazardous systems.
●They are trained or instructed in maintenance and use of appropriate safety equipment
according to the pertinent safety regulations.
WARNING
Use in hazardous area
Risk of explosion.
•Only use equipment that is approved for use in the intended hazardous area and
labelled accordingly.
•Don't use devices that have been operated outside the conditions secified for hazardous
areas. If you have used the device outside the conditions for hazardous areas
permanently make all Ex markings unrecognizable on the nameplate.

Safety notes
2.5 Use in flameproof enclosures "d" and protection in enclosures "tb"
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
14 Compact Operating Instructions, 01/2018, A5E03920348-AE
See also
Technical data (Page 45)
WARNING
Loss of safety of device with type of protection "Intrinsic safety Ex i"
If the device has already been operated in non-intrinsically safe circuits or the electrical
specifications have not been observed, the safety of the device is no longer ensured for use
in hazardous areas. There is a risk of explosion.
•Connect the device with type of protection "Intrinsic safety" solely to an intrinsically safe
circuit.
•Observe the specifications for the electrical data on the certificate and/or in Technical
data (Page 45).
2.5
Use in flameproof enclosures "d" and protection in enclosures "tb"
WARNING
Impermissible repair of explosion protected devices
Risk of explosion in hazardous areas
•Repair must be carried out by Siemens authorized personnel only.
WARNING
Electrostatic charge
Risk of explosion in hazardous areas if electrostatic charges develop, for example, when
cleaning plastic surfaces with a dry cloth.
•Prevent electrostatic charging in hazardous areas.

Safety notes
2.5 Use in flameproof enclosures "d" and protection in enclosures "tb"
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Compact Operating Instructions, 01/2018, A5E03920348-AE 15
2.5.1
For SITRANS TS500
●The enclosures types AG0, AH0, AU0, AV0 and SITRANS TF of the temperature
sensors, series TS500 have to be connected by means of suitable cable entry fittings or
conduit systems, which meet the requirements of IEC/EN 60079-1, sections 13.1 and
13.2, and for which a separate examination certificate has been issued.
●Cable entry fittings (conduit threads) and sealing plugs of simple design must not be used
in the transmitter and receiver enclosures.
●Any openings in the transmitter and receiver enclosures that are not used must be closed
as specified in IEC/EN 60079-1, section 11.9.
●The connecting lead of enclosures types AG0, AH0, AU0, AV0 and SITRANS TF of the
temperature sensors, series TS500, must be installed to provide for permanent wiring
and adequate protection against damage.
●If the temperature at entry fittings should exceed 60 °C, the connecting cables used have
to be of the temperature-resistant type.
●If connection is made in the potentially explosive area, the connecting cable
(unconnected cable end) of the enclosure types AG0, AH0, AU0, AV0 and TF of the
temperature sensors, series TS500, must be connected in an enclosure that meets the
requirements of an approved type of protection as specified in IEC/EN 60079-0, section
1.
●All models are to be mounted within Thermowells suitably rated for the application they
are used.
●If a SITRANS TS500 with XP type of protection is combined with a thermowell, consider
the ASME PTC19.3 and a minimum wall thickness of 1 mm.
●To separate zone 1 from zone 2 in a hazardous area, consider a wall thickness of ≥1 mm
with austenitic steel. In addition, consider the existing process conditions.
If a thermowell installed correctly and tight at Zone 0, the sensor that is screwed in this
thermowell needs at least zone 1 approval.
●Suitably rated Thermowells are to have thread engagement of 5 full turns wrench tight.
●Notes to this effect must accompany each device in an adequate form.
●Components attached or installed (terminal compartments, bushings, cable entry fittings,
connectors) must be of a technical standard that complies with the specifications on the
Certificate of Conformity as a minimum, and a separate examination certificate must have
been issued for them.
●Use the device to measure temperature in accordance with the technical data for
maximum permitted ambient temperatures in the connection area of the sensor. See
chapter Gas hazardous area: Ex d / XP (Page 52) and Dust hazardous area: Ex i / IS / Ex
tb / DIP (Page 53).

Safety notes
2.5 Use in flameproof enclosures "d" and protection in enclosures "tb"
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
16 Compact Operating Instructions, 01/2018, A5E03920348-AE
2.5.2
For SITRANS TSinsert/TS100/TS200/TS500
NOTICE
Ambient temperature too high
Damage to cable sheath.
•At an ambient temperature ≥60 °C (140 °F), use heat-resistant cables suitable for an
ambient temperature at least 20 °C (36 °F) higher.

TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Compact Operating Instructions, 01/2018, A5E03920348-AE 17
Description
3
3.1
Overview
SITRANS TS product family
①
SITRANS TS100 7MC71..
general use, compact design with connecting cable
②
SITRANS TS200 7MC72..
general use, compact design
③
SITRANS TS500 7MC75../7MC55..
general use, modular design with connection head (European portfolio/ Chinese portfolio)
④
SITRANS TSinsert measuring insert for use in the SITRANS TS500 series
⑤
SITRANS TS500 7MC65../7MC55..
general use, modular design with connection head (North American portfolio/ Chinese portfolio)

Description
3.2 Application
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
18 Compact Operating Instructions, 01/2018, A5E03920348-AE
Elementary sensors
Resistance thermometers or thermocouples can be used for temperature measurement.
3.2
Application
The temperature sensors of the SITRANS TS product family are used for measuring
temperatures in industrial plants.
Depending on the specifications, sensors can be combined with different connection heads,
extension tubes, and process connections. This makes the sensors suitable for a variety of
process engineering applications, in the following sectors:
●Petrochemical industry
●Pharmaceuticals industry
●Biotechnology
●Food production
3.3
Functional principles
Two different measuring principles are used for measuring temperatures.
●With resistance thermometers, the temperature is measured as a change in resistance.
Resistance thermometers, also called Resistance Temperature Devices (RTD), contain
sensor elements, like the Pt100 sensor elements in accordance with IEC 60751.
●With thermocouples, the temperature is the change in voltage (Seebeck effect). The
thermocouples are in accordance with IEC 584/DIN EN 60584.
3.4
Nameplate structure
Positioning of nameplate
Note
SITRANS TS100/TS200 nameplate
Before commissioning, make sure the nameplate is securely fas
tened to the temperature
sensor in a visible location.
Device
Positioning of the nameplate
SITRANS TSinsert 7MC701. On the bottom of the connecting plate or at the
outer periphery of the ANSI adapter.
SITRANS TS100 7MC71..
On the sensor cable

Description
3.5 Temperature transmitter for SITRANS TS500
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
Compact Operating Instructions, 01/2018, A5E03920348-AE 19
Device
Positioning of the nameplate
SITRANS TS200 7MC72..
On the connector or on the sensor
SITRANS TS500 7MC.5.. On the connection head
Example of nameplate
①
Product name
②
Order number (machine-readable product
code)
③
Additional information on the type
④
Valid standard for the device
⑤
Serial number
⑥
CE marking
⑦
Place of manufacture
⑧
Consult the operating instructions.
⑨
Type-specific information Explosion pro-
tection/electrical data
⑩
Manufacturer´s specifications
3.5
Temperature transmitter for SITRANS TS500
The following head-mounted transmitters can be combined with the temperature sensors
SITRANS TS500:
Transmitter
Features
Sensor
TH100 •Base device
•Output 4 ... 20 mA
•Can be configured using simple software
•Po: 12.5 mW
only 1)
TH200 •Universal device
•Output 4 ... 20 mA
•Can be configured using simple software
•Po: 37 mW
1) or 2)

Description
3.6 Measuring inserts for SITRANS TS500
TS100/TS200/TS300/TS500/TSinsert/TSthermowell
20 Compact Operating Instructions, 01/2018, A5E03920348-AE
Transmitter
Features
Sensor
TH300 •Universal
•Output 4 ... 20 mA / HART
•Diagnostic functions
•Po: 37 mW
1) or 2)
TH400 •Output: PROFIBUS PA or FOUNDATION Fieldbus
•Sensor redundancy
•Diagnostics
•Po: 12 mW
1) or 2)
1)
Resistance thermometers
2)
Thermocouple
Note
SITRANS TS500 IEC Ex
If the contained SITRANS TH transmitter is not IEC Ex compliant, the TS500 nameplate has
ATEX marking only.
3.6
Measuring inserts for SITRANS TS500
Measuring inserts for SITRANS TS500 temperature sensors are available in three variants:
●Variant 1:
DIN mounting disk for accommodating a transmitter or ceramic socket.
●Variant 2:
Fixed connection of the ends of the mineral insulated cable with a DIN ceramic socket.
●Variant 3:
Measuring insert in a spring-loaded adapter (ANSI).