Siemens TSP-XC User manual

SiemensSiemens
SiemensSiemens
Siemens IndustryIndustry
IndustryIndustry
Industry,,
,,
,Inc.Inc.
Inc.Inc.
Inc.
BuildingBuilding
BuildingBuilding
Building
TT
TT
Tecec
ecec
echnologies Dihnologies Di
hnologies Dihnologies Di
hnologies Divisionvision
visionvision
vision
P/N 315-049950-3
INTRODUCTION The Model TSP-XC Cable Kit from Siemens Industry, Inc., is used to wire TSP-40A
printers to FireFinder-XLS Systems.The two cables in the TSP-XC kit replace the
cables (P/Ns 600-290606 and 600-290607) that are shipped with the TSP-40A.
For additional information on the FireFinder-XLS System, refer to the FireFinder-XLS
Control Panel Installation, Operation and Maintenance Manual, P/N 315-033744. For
information on installing the TSP-40A in a FireFinder-XLS System, refer to installation
instructions, P/N 315-049949.
Installation of the TSP-40A in a FireFinder-XLS System requires the following kits:
P/N 500-634933 TSP-40A Printer Module
P/N 500-849949 TSP-XB U-Shaped Bracket and Front Plate
P/N 500-849950 TSP-XC Cable Kit
WIRING TheTSP-40A printer modules comes with two cables, P/N 600-290607 and P/N 600-
290606. These cables are used only in MXL/MXLV System installations. The two
cables used in FireFinder-XLS Systems installations—a two-conductor power cable
and a data cable—are contained in the TSP-XC cable kit, P/N 500-849950.
The two-conductor power cable has a plug on one end that connects to P1 on the
TSP-40A. The power cable is provided at a length of 5 feet. Cut the wire to the length
needed and strip the insulation from the end of the wire 1/4” - 3/8”. The wired end
connects to the terminals on TB-4 of the PSC-12 or PSX-12, with the red wire going
to the positive (+) terminal and the black wire going to the negative (-) terminal.
The data (ribbon) cable connects to P3 on the TSP-40A and to either JP4 on the back
of the PMI (note that the silk screen on the PMI indicates NIM-1M) or to J13 on the
back of the PMI-2 (note that the silk screen on the PMI-2 indicates TSP-40A). Both
ends of the data cable have the same keyed plug that fits only one way onto the
connectors.
Refer to Figure 1 for the location of the terminals on the TSP-40A, Figure 2 for the
location of the connection to JP4 on the back of the PMI and Figure 3 for the location
of the connection to J13 on the back on the PMI-2.
TSP-40A Cable Kit for FireFinder-XLS
Installation Instructions
ModelTSP-XC

S16
C
4218
C
4218
C
4218
JP9
D19
D20
D42 D23
S17
S14 S11
U10
S1
TP1
S2
JP5
R61
J2
JP7
J1
1
XNET
HNET PMI
PMI-DAC
4
FAIL
A
C
CONTRAST
OPTIONS RESET
ADDRESS
132
ON
EARTHGND
STATUS
456
10
11
23
6DEBUG 9
1
9
10
5
1
2
UPLOADHNET
5
11
5
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
NIM-1M
TOP
TO P3 ON
TSP-40A
(DATA CABLE)
JP4 1
10 2
9
UPLOAD
OPTIONS
STATUS
LINK
100
ACT
XNET
ADDRESS
TSP-40A
RESET
LAN SD #1 SD #2
EARTH
GND
1234
J13
S2 S3 S4
S1
J16
J15
J11
ON
TO P3 ON
TSP-40A
(DATA CABLE)
P1
P3
-+
TO
PSC-12/
PSX-12,
TB4
TO JP4 ON BACK OF PMI
(SILK SCREEN
INDICATES NIM-1M)
OR
TO J13 ON BACK OF PMI-2
(SILK SCREEN
INDICATES TSP-40A)
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Canada Limited
Building Technologies Division
2 Kenview Boulevard
Brampton, Ontario L6T 5E4 Canada
P/N 315-049950-3
Figure 1
Wiring the TSP-40A
Figure 3
TSP-40A Data Cable Connection on Back of PMI-2
Figure 2
TSP-40A Data Cable Connection on Back of PMI