Siemens 6XV1875-5AH10 User guide

SIMATIC NET
Industrial Wireless LAN
Passive network components
IWLAN
System Manual
08/2021
C79000-G8976-C282-08
Preface 1
Product overview 2
Technical data 3

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage
to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices
referring only to property damage have no safety alert symbol. These notices shown below are graded according to
the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Quali󹪝ed Personnel
The product/system described in this documentation may be operated only by personnel quali󹪝ed for the speci󹪝c
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Quali󹪝ed personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identi󹪝ed by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may
be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C282-08
Ⓟ 08/2021 Subject to change
Copyright © Siemens AG 2012 - 2021.
All rights reserved

Table of contents
1 Preface ................................................................................................................................................... 5
2 Product overview................................................................................................................................... 9
2.1 Cabling technique................................................................................................................ 9
2.1.1 Overview............................................................................................................................. 9
2.1.2 Area of application............................................................................................................. 13
2.2 Further passive components .............................................................................................. 15
2.2.1 Antennas........................................................................................................................... 15
2.2.2 RCoax cables...................................................................................................................... 16
2.3 Active components ............................................................................................................ 17
2.3.1 Access points..................................................................................................................... 17
2.3.1.1 IEEE 802.11n ..................................................................................................................... 17
2.3.1.2 IEEE 802.11ac.................................................................................................................... 18
2.3.1.3 IEEE 802.11ax.................................................................................................................... 19
2.3.2 Client modules................................................................................................................... 20
2.3.2.1 IEEE 802.11n ..................................................................................................................... 20
2.3.2.2 IEEE 802.11ac.................................................................................................................... 21
2.3.2.3 IEEE 802.11ax.................................................................................................................... 22
3 Technical data...................................................................................................................................... 23
3.1 Flexible connecting cables ................................................................................................. 23
3.1.1 Introduction....................................................................................................................... 23
3.1.2 IWLAN N-Connect male/male ............................................................................................. 24
3.1.3 IWLAN QMA/N-Connect male/female.................................................................................. 25
3.1.4 IWLAN R-SMA/SMA male/male............................................................................................ 27
3.1.5 IWLAN N-Connect/R-SMA male/male................................................................................... 29
3.1.6 IWLAN N-Connect male/male (railway applications)............................................................ 31
3.1.7 IWLAN QMA/N-Connect male/female (railway applications) ................................................ 33
3.1.8 IWLAN N-Connect/R-SMA male/male (railway applications) ................................................. 35
3.2 Terminating resistors.......................................................................................................... 37
3.2.1 N terminating resistance 50 Ω – male ................................................................................ 37
3.2.2 R-SMA terminating resistor 50 Ω – male ............................................................................. 38
3.3 Lightning protectors........................................................................................................... 40
3.3.1 Lightning protector LP798-1N ............................................................................................ 40
3.3.2 Lightning protector LP798-2N ............................................................................................ 41
3.4 Panel feedthroughs............................................................................................................ 43
3.4.1 Panel feedthrough N-Connect female/female...................................................................... 43
3.4.2 Panel feedthrough N/SMA female/female ........................................................................... 44
3.5 Attenuator N-Connect male/female .................................................................................... 46
3.6 Power splitter N-Connect female ....................................................................................... 47
3.7 HF coupler N-Connect male/male ...................................................................................... 48
3.8 R-SMA angle adapter.......................................................................................................... 49
Passive network components IWLAN
System Manual, 08/2021, C79000-G8976-C282-08 3

Index .................................................................................................................................................... 51
Table of contents
Passive network components IWLAN
4System Manual, 08/2021, C79000-G8976-C282-08

Preface 1
Purpose of the system manual
This manual explains the entire IWLAN cabling that you require for your IWLAN application. For a
󹪞exible combination and installation of the individual IWLAN components both indoors and
outdoors, a wide ranging selection of compatible coaxial accessories is available. The manual
also covers connecting cables as well as a variety of plug-in connectors, lightning protectors, a
power splitter and an attenuator.
Figure 1-1 IWLAN product overview
Certi󹪝cation
The products and systems listed in this document are manufactured and marketed using a
quality management system complying with DIN ISO 9001 (Certi󹪝cate Register no. 2613) and
certi󹪝ed by DQS. The DQS certi󹪝cate is recognized in all IQNet countries (reg. no.: 2613).
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
Passive network components IWLAN
System Manual, 08/2021, C79000-G8976-C282-08 5

In order to protect plants, systems, machines and networks against cyber threats, it is necessary
to implement – and continuously maintain – a holistic, state-of-the-art industrial security
concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected to
an enterprise network or the internet if and to the extent such a connection is necessary and only
when appropriate security measures (e.g. 󹪝rewalls and/or network segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity (https://www.siemens.com/industrialsecurity).
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are no longer
supported, and failure to apply the latest updates may increase customer’s exposure to cyber
threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed
under
https://www.siemens.com/industrialsecurity (https://www.siemens.com/industrialsecurity).
Decommissioning
Shut down the device properly to prevent unauthorized persons from accessing con󹪝dential
data in the device memory.
To do this, restore the factory settings on the device.
Also restore the factory settings on the storage medium.
Recycling and disposal
The products are low in pollutants, can be recycled and meet the requirements of the WEEE
directive 2012/19/EU for the disposal of electrical and electronic equipment.
Do not dispose of the products at public disposal sites.
For environmentally friendly recycling and the disposal of your old device contact a certi󹪝ed
disposal company for electronic scrap or your Siemens contact (Product return (https://
support.industry.siemens.com/cs/ww/en/view/109479891)).
Note the di󹪜erent national regulations.
Device defective
If a fault develops, send the device to your SIEMENS representative for repair. Repairs on-site are
not possible.
SIMATIC NET glossary
Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
Preface
Passive network components IWLAN
6System Manual, 08/2021, C79000-G8976-C282-08

You will 󹪝nd the SIMATIC NET glossary on the Internet at the following address:
50305045 (https://support.industry.siemens.com/cs/ww/en/view/50305045)
Trademarks
The following and possibly other names not identi󹪝ed by the registered trademark sign ® are
registered trademarks of Siemens AG:
SCALANCE, C-PLUG, RCoax
Preface
Passive network components IWLAN
System Manual, 08/2021, C79000-G8976-C282-08 7

Preface
Passive network components IWLAN
8System Manual, 08/2021, C79000-G8976-C282-08

Product overview 2
This section introduces you to the IWLAN products. You will 󹪝nd technical speci󹪝cations in the
section "Technical data (Page 23)".
2.1 Cabling technique
2.1.1 Overview
The following passive IWLAN components are available:
Flexible connecting cables
SIEMENS IWLAN RCoax N-Connect/N-Connect male/male
Flexible connecting cable for linking two RCoax cables or an
antenna to a SCALANCE W700 access point with N-Connect
connectors.
Preassembled with two N-Connect male connectors:
• 6XV1875-5AH10 (length 1 m)
• 6XV1875-5AH20 (length 2 m)
• 6XV1875-5AH50 (length 5 m)
• 6XV1875-5AN10 (length 10 m)
SIEMENS IWLAN QMA/N-Connect male/female
Adapter cable for connecting a MIMO antenna with QMA con‐
nectors with the 󹪞exible connecting cables. Preassembled with
two connectors QMA male and N-Connect female:
• 6XV1875-5JH10 (length 1 m)
Passive network components IWLAN
System Manual, 08/2021, C79000-G8976-C282-08 9

SIEMENS SIMATIC NET IWLAN RCoax/Antenna Connection
Cable R-SMA/SMA male/male
Flexible connecting cable for connecting a SCALANCE W700 or
IWLAN/PB Link PN IO to components with R-SMA and SMA con‐
nectors, for example cabinet feedthrough.-
Preassembled with two connectors R-SMA male to SMA male:
• 6XV1875-5DE30 (length 0.3 m)
• 6XV1875-5DH20 (length 2 m)
SIEMENS SIMATIC NET IWLAN RCoax/Antenna Connection
Cable N-Connect/R-SMA male/male
Flexible connecting cable for connecting an RCoax cable or an
antenna to a SCALANCE W700. Preassembled with two N-Con‐
nect male and R-SMA male connectors:
• 6XV1875-5CE30 (length 0.3m)
• 6XV1875-5CH10 (length 1 m)
• 6XV1875-5CH20 (length 2 m)
• 6XV1875-5CH50 (length 5 m)
• 6XV1875-5CN10 (length 10 m)
Flexible connecting cables for railway applications
SIEMENS SIMATIC NET Cable N-Connect male/male railway
Flexible connecting cable, e.g. for connecting antennas; suita‐
ble for IWLAN and mobile wireless; for railway applications.
Preassembled with two N-Connect male/male connectors
• 6XV1875-5SH10 (Länge 1m)
• 6XV1875-5SH20 (Länge 2m)
• 6XV1875-5SH50 (Länge 5m)
SIMATIC NET Cable QMA /N-Connect male/female railway
Flexible adapter cable of antenna with QMA socket for antenna
connecting cable, for railway applications.
Preassembled with two QMA /N-Connect male/female connec‐
tors
• 6XV1875-5VH10 (Länge 1m)
SIEMENS SIMATIC NET Cable N-Connect/ R-SMA male/male
railway
Flexible connecting cable, e.g. for access point antenna, for rail‐
way applications.
Preassembled with two N-Connect R-SMA male/male connectors
• 6XV1875-5TH10 (Länge 1m)
• 6XV1875-5TH20 (Länge 2m)
• 6XV1875-5TH50 (Länge 5m)
Product overview
2.1 Cabling technique
Passive network components IWLAN
10 System Manual, 08/2021, C79000-G8976-C282-08

Terminating resistors
SIEMENS SIMATIC NET IWLAN RCoax N-Connect Male Termi‐
nation Impedance 50 Ω TI795-1N
Terminating impedance for RCoax cables and open wireless inter‐
faces on SCALANCE W devices with N-Connects, impedance 50
ohms,
• 6GK5795-1TN00-1AA0
SIEMENS SIMATIC NET IWLAN Termination Impedance
TI795-1R
R-SMA terminator for 󹪝tting to the unused antenna socket of a
SCALANCE W7xx when using one antenna only. Impedance 50 Ω,
R-SMA male connector.
• 6GK5795-1TR10-0AA6
Lightning protectors
SIEMENS SIMATIC NET IWLAN Lightning Protector with N/N
female/female connector LP 798-2N
Lightning protector with maintenance-free quarter-wave technol‐
ogy for frequencies in the range 2 to 6 GHz.
• 6GK5798-2LP10-2AA6
SIEMENS SIMATIC NET IWLAN Lightning Protector with N/N
female/female connector LP 798-1N
Lightning protector with gas discharge capsule, also suitable for
DC current on the 󹪞exible connecting cable 0 to 6 GHz.
• 6GK5798-2LP00-2AA6
Product overview
2.1 Cabling technique
Passive network components IWLAN
System Manual, 08/2021, C79000-G8976-C282-08 11

Panel feedthroughs
SIEMENS SIMATIC NET IWLAN Antenna N-Connect/N-Connect
female/female Panel Feedthrough
Panel feedthrough/adapter N-N for wall thicknesses up to a maxi‐
mum of 4.5 mm, N-Connect/N-Connect connectors
• 6GK5798-2PP00-2AA6
SIEMENS SIMATIC NET IWLAN RCoax N-Connect/SMA Female/
Female Panel Feedthrough
Panel feedthrough with securing 󹪞ange for wall thicknesses up to
a maximum of 5.5 mm, SMA female and N-Connect female con‐
nectors
• 6GK5798-0PT00-2AA0
Attenuator
SIEMENS SIMATIC NET IWLAN RCoax N-Connect Male/Female
Attenuator 10 dB
Attenuator with N-Connect male / N-Connect female connectors
• 6GK5798-0AP00-4CA0
Power splitter
SIEMENS SIMATIC NET IWLAN RCoax N-Connect Female Pow‐
er Splitter 2-Way
Two-way power splitter, Y element for splitting the RCoax cable or
for the use of two antennas on one wireless interface.
• 6GK5798-0SN00-0EA0
HF coupler
RCoax N-Connect male/male Coupler
HF coupler, among other things for connecting two RCoax cables;
two N-Connect male connectors.
• 6GK5798-0CP00-1AA0
Product overview
2.1 Cabling technique
Passive network components IWLAN
12 System Manual, 08/2021, C79000-G8976-C282-08

HF angle adapter
HF angle adapter
90° angle adapter with R-SMA male /R-SMA female connectors
• 6GK5798-1CS00-4AA0
2.1.2 Area of application
Flexible connecting cables
• The 󹪞exible IWLAN RCoax/antenna connecting cables are required for connecting RCoax
segments or antennas to active devices.
• The cables provide low attenuation so that the quality of the wireless signal is only minimally
impaired.
• The antenna cables are 󹪞ame retardant, chemical resistant and silicone-free.
Terminating resistors
• To avoid impairing wireless quality, terminating resistors are required to close unused
antenna connectors on the access points and clients.
• RCoax segments must be terminated at the end with a terminating resistor.
Lightning protectors
When using separate antennas outdoors, there is a risk of lightning strikes. To protect the
equipment, a lightning protector can be used.
Panel feedthroughs
The panel feedthroughs along with the antenna connecting cables allow simple connection of
separately installed antennas and the active components installed in cabinets or cubicles.
Attenuator
The 10 dB attenuator is always used when the transmitted power both in the send and receive
direction needs to be reduced. Typical areas of application are short RCoax segments or
directional wireless links that need to be restricted in terms of spread.
Power splitter
With the aid of the power splitter, the transmit power of an access point is distributed over two
RCoax or antenna segments. This allows wireless coverage in two di󹪜erent areas with only one
access point.
Product overview
2.1 Cabling technique
Passive network components IWLAN
System Manual, 08/2021, C79000-G8976-C282-08 13

Product variants
Flexible connecting cables
• Preassembled cable lengths (0.3 m to 10 m)
•Di󹪜erent connector types and combinations:
– N-Connect
– R-SMA
– SMA
– QMA
Terminating resistors
• TI795-1R: Terminating resistor for R-SMA antenna sockets
• TI795-1N: Terminating resistor for N-Connect antenna sockets or RCoax segments
Lightning protectors
• LP798-2N
Maintenance-free lightning protector for N-Connect connectors:
– Quarter wave technology (lambda quarter) for the frequency range 2 to 6 GHz
– forms a short circuit for direct voltages so that all kinds of overvoltages can be diverted
reliably
– not suitable for DC supply via antenna cable
• LP798-1N
Lightning protector for N-Connect connectors:
– with gas discharge protector for the frequency range 0 to 6 GHz for N-Connect connectors
– suitable for DC supply via antenna cable
Panel feedthroughs
• N-Connect female/SMA female with securing 󹪞ange for wall thicknesses up to a maximum of
5.5 mm.
• N-Connect female/N-Connect female without 󹪞ange for wall thicknesses up to a maximum
of 4.5 mm. This can also be used as a link between two antenna connecting cables.
Product overview
2.1 Cabling technique
Passive network components IWLAN
14 System Manual, 08/2021, C79000-G8976-C282-08

2.2 Further passive components
2.2.1 Antennas
Product connections
The products described up to now are used to connect the following passive components to
access points and clients:
Type Properties Article number
IWLAN RCoax Antenna
ANT792-4DN
RCoax helical antenna with circular polariza‐
tion for RCoax systems, 4 Bi, 2.4 GHz, IP65, N-
Connector female.
6GK5792-4DN00-0AA6
ANT792-6MN Omnidirectional antenna, mast/wall mount‐
ing, 6 dBi 2.4 GHz, IP67, N-Connect female
6GK5792-6MN00-0AA6
ANT792-8DN Directional antenna, mast/wall mounting,
14 dBi 2.4 GHz, IP32, N-Connect female
6GK5792-8DN00-0AA6
IWLAN RCoax
ANT793-4MN
RCoax λ4 antenna with vertical polarization
for RCoax systems, 6 dBi, 5 GHz, IP65, N-Con‐
nector female
6GK5793-4MN00-0AA6
ANT793-6DG Wide angle antenna, mast/wall mounting,
9 dBi 5 GHz, IP66/67, 2 x N-Connect female
6GK5793-6DG00-0AA0
ANT793-8DJ Directional antenna, mast/wall mounting,
18 dBi 5 GHz, IP67, 2 x N-Connect female
6GK5793-8DJ00-0AA0
ANT793-8DK Directional antenna, mast/wall mounting,
23 dBi 5 GHz, 2 x N-Connect female
6GK5793-8DK00-0AA0
ANT793-8DL Directional antenna vertical-horizontal polar‐
ized, 5 GHz, 14dBi, IP66, 2xN-Connect female
6GK5793-8DL00-0AA0
ANT793-8DP Directional antenna, mast/wall mounting,
13 / 13.5 dBi 4.9 GHz and 5 GHz, N-Connect
female
This antenna is not available in Korea
6GK5793-8DP00-0AA0
ANT795-4MA Omnidirectional antenna, directly on the de‐
vice, 3/5 dBi 2.4 GHz and 5 GHz, IP30, R-SMA
connector male for direct installation on the
device, angle connector adjustable 0° - 180°.
6GK5795-4MA00-0AA3
ANT795-4MB Omnidirectional antenna, 2/3 dBi 2.4 GHz and
5 GHz, IP30, R-SMA connector female for di‐
rect mounting on the device, angle connector
adjustable 0° to 90°.
6GK5795-4MB00-0Ax0
ANT795-4MC Omnidirectional antenna, 3/5 dBi, 2.4 GHz
and 5 GHz, IP65, N-Connect male for direct
installation on the device, straight connector.
6GK5795-4MC00-0AA3
ANT795-4MD Omnidirectional antenna, 3/5 dBi, 2.4 GHz
and 5 GHz, IP65, N-Connect male for direct
installation on the device, 90° connector.
6GK5795-4MD00-0AA3
ANT795-4MX Omnidirectional antenna, 2/2.5 dBi, 2.4 GHz
and 5 GHz, IP69K, N-Connect male
6GK5795-4MX00-0AA0
Product overview
2.2 Further passive components
Passive network components IWLAN
System Manual, 08/2021, C79000-G8976-C282-08 15

Type Properties Article number
ANT795-6DC Wide angle antenna, mast/wall mounting,
9 dBi 2.4 GHz and 5 GHz, N-Connect female
6GK5795-6DC00-0AA0
ANT795-6MN Omnidirectional antenna, mounted on roof/
vehicle, 6/8 dBi 2.4 GHz and 5 GHz, N-Connect
female
6GK5795-6MN10-0AA6
ANT795-6MT Omnidirectional antenna (MIMO), mounted
on roof/vehicle/ceiling, 5/7 dBi 2.4 GHz and
5 GHz, 3 x QMA connector female
6GK5795-6MT00-0AA0
ANT795-6MP Omnidirectional antenna, 5/7 dBi, 2.4 GHz
and 5 GHz, IP65/67, N-Connect female
6GK5795-6MP00-0AA0
Note
You will 󹪝nd further information in the compact operating instructions of the individual
components.
2.2.2 RCoax cables
Component Description Article number
IWLAN RCoax cable Radiating cables for areas with di󹪟cult wireless
conditions as a special antenna for SCALANCE
W access points. For the expanded tempera‐
ture range (-40 °C to +85 °C).
Sold by the meter, minimum order 20 meters
2.4 GHz 6XV1875-2A
5 GHz 6XV1875-2D
Note
Further information
You will 󹪝nd further information in the system manual for RCoax (https://
support.industry.siemens.com/cs/de/en/view/84922825).
Product overview
2.2 Further passive components
Passive network components IWLAN
16 System Manual, 08/2021, C79000-G8976-C282-08

2.3 Active components
2.3.1 Access points
2.3.1.1 IEEE 802.11n
SCALANCE W700
The SCALANCE W700 access points with one or more wireless interfaces are suitable for setting
up Industrial Wireless LANs. Both infrastructure networks and point-to-point links can be
implemented. The most important characteristics of the various product variants are shown in
the table below. You will 󹪝nd detailed information in the documentation of the relevant device.
Type Connectors for exter‐
nal antennas
Number of
connectable
devices (3)
iPCF
mode (1)
IEEE
802.11
a/b/g/h
IEEE
802.11n
Article number
R-SMA N-Connect
W761-1 RJ45 1 4 ● 1 x 1 6GK5761-1FC00-0AA0
6GK5761-1FC00-0AB0 (4)
W774‑1 RJ45 2 8 ● (2) ● 2 x 2 6GK5774-1FX00-0AA0
6GK5774-1FX00-0AB0 (4)
6GK5774-1FX00-0AC0 (5)
W774‑1 M12
EEC
2 8 ● (2) ● 2 x 2 6GK5774-1FY00-0TA0
6GK5774-1FY00-0TB0 (4)
W778-1 M12 2 8 ● (2) ● 2 x 2 6GK5778-1GY00-0AA0
6GK5778-1GY00-0AB0 (4)
W778‑1 M12
EEC
2 8 ● (2) ● 2 x 2 6GK5778-1GY00-0TA0
6GK5778-1GY00-0TB0 (4)
W788-1 M12 3 8 ● (2) ● 3 x 3 6GK5788-1GD00-0AA0
6GK5788-1GD00-0AB0 (4)
W788-2 M12 6 8 ● (2) ● 3 x 3 6GK5788-2GD00-0AA0
6GK5788-2GD00-0AB0 (4)
W788-2 M12
EEC
6 8 ● (2) ● 3 x 3 6GK5788-2GD00-0TA0
6GK5788-2GD00-0TB0 (4)
6GK5 788-2GD00-0TC0 (5)
W788-1 RJ-45 3 8 ● (2) ● 3 x 3 6GK5788-1FC00-0AA0
6GK5788-1FC00-0AB0 (4)
W788-2 RJ-45 6 8 ● (2) ● 3 x 3 6GK5788-2FC00-0AA0
6GK5788-2FC00-0AB0 (4)
6GK5788-2FC00-0AC0 (5)
W786-1 RJ-45 3 8 ● (2) ● 3 x 3 6GK5786-1FC00-0AA0
6GK5786-1FC00-0AB0 (4)
6GK5786-2FC00-0AC0 (5)
Product overview
2.3 Active components
Passive network components IWLAN
System Manual, 08/2021, C79000-G8976-C282-08 17

Type Connectors for exter‐
nal antennas
Number of
connectable
devices (3)
iPCF
mode (1)
IEEE
802.11
a/b/g/h
IEEE
802.11n
Article number
R-SMA N-Connect
W786-2 RJ-45 6 8 ● (2) ● 3 x 3 6GK5786-2FC00-0AA0
6GK5786-2FC00-0AB0 (4)
W786-2IA
RJ-45
8 ● (2) ● 3 x 3 6GK5786-2HC00-0AA0
6GK5786-2HC00-0AB0 (4)
W786-2 SFP 6 8 ● (2) ● 3 x 3 6GK5786-1FE00-0AA0
● suitable
(1) The iPCF mode provides an optimized data throughput and minimum handover times.
(2) With KEY-PLUG inserted
(3) In client mode
(4) US variant
(5) IL variant
2.3.1.2 IEEE 802.11ac
SCALANCE W1700
The SCALANCE W1700 access points with two Ethernet and up to two WLAN interfaces are
highly suitable for setting up Industrial Wireless LANs. Both infrastructure networks and point-to-
point links can be implemented.
SCALANCE W1700 features multiuser MIMO and can transmit data to up to four WLAN clients
simultaneously.
SCALANCE W1700 devices feature an integrated switch and can be networked in a variety of
ways over their two managed Ethernet Gigabit ports.
SCALANCE W1700 is compatible with the IEEE 802.11n WLAN standards.
SCALANCE W1700 devices supports IP65 degree of protection, which means they are dust-proof
and fully protected against contact and water jets (nozzle) from any direction. The SCALANCE
W1788 EEC is suitable for use in harsh environments.
The most important characteristics of the various product variants are shown in the table below.
You can 󹪝nd detailed information in the documentation of SCALANCE W1700 devices.
Type Antennas Spatial
streams
(data
streams)
Max. data
rate
(gross in
Mbps)
Ethernet interfa‐
ces
Article number
Quan‐
tity
Connections
SCALANCE W1788-1 4 N-Connect 1 to 4
(max. 4 per
client)
1733 2 x M12 for 1000
Mbps,
1 x PoE
6GK5788-1GY01-0AA0
6GK5788-1GY01-0AB0
(USA)
SCALANCE W1788-2 8 N-Connect 1 to 8
(max. 4 per
client)
1733 2 x M12 for 1000
Mbps,
1 x PoE
6GK5788-2GY01-0AA0
6GK5788-2GY01-0AB0
(USA)
Product overview
2.3 Active components
Passive network components IWLAN
18 System Manual, 08/2021, C79000-G8976-C282-08

Type Antennas Spatial
streams
(data
streams)
Max. data
rate
(gross in
Mbps)
Ethernet interfa‐
ces
Article number
Quan‐
tity
Connections
SCALANCE W1788-2
EEC
8 N-Connect 1 to 8
(max. 4 per
client)
1733 2 x M12 for 1000
Mbps,
1 x PoE
6GK5788-2GY01-0TA0
6GK5788-2GY01-0TB0
(USA)
SCALANCE W1788-2IA 8 Internal 1 to 8
(max. 4 per
client)
1733 2 x M12 for 1000
Mbps,
1 x PoE
6GK5788-2HY01-0AA0
6GK5788-2HY01-0AB0
(USA)
2.3.1.3 IEEE 802.11ax
SCALANCE WAM76x
The SCALANCE WxM76x support the WLAN standard IEEE 802.11ax (Wi-Fi6) and are suitable for
simultaneous connection of mobile devices in very tight spaces. They o󹪜er similar service quality
for each device.
The SCALANCE WxM76x have the sleep mode function and can switch o󹪜 mobile devices in the
network via the digital input/output interface.
The SCALANCE WxM766 have a rugged housing with IP65 degree of protection. The SCALANCE
WAM766-1 EEC is suitable for use in harsh environments.
The most important characteristics of the product variants are shown in the table below. You can
󹪝nd detailed information in the documentation for SCALANCE W700ax devices.
Type Antennas Spatial
streams
(data
streams)
Max. data
rate (gross
in Mbps)
Ethernet interfa‐
ces
Article number
Quan‐
tity
Connec‐
tions
SCALANCE WAM766-1 2 N-Connect 1 to 2 1201 1 x M12 for 1000
Mbps,
1 x PoE
6GK5766-1GE00-7DA0
6GK5766-1GE00-7DB0
(USA)
SCALANCE WAM766-1
EEC
2 N-Connect 1 to 2 1201 1 x M12 for 1000
Mbps,
1 x PoE
6GK5766-1GE00-7TA0
6GK5766-1GE00-7TB0
(USA)
Product overview
2.3 Active components
Passive network components IWLAN
System Manual, 08/2021, C79000-G8976-C282-08 19

2.3.2 Client modules
2.3.2.1 IEEE 802.11n
SCALANCE W700
The SCALANCE W700 client modules establish a connection between wired Ethernet and
Industrial Wireless LAN. The most important characteristics of the various product variants are
shown in the table below. You will 󹪝nd detailed information in the documentation of the
relevant device.
Type Connectors for external
antennas
Number of
connectable
devices (3)
iPCF
mode (1)
IEE
802.11
a/b/g/h
IEEE
802.11n
Article number
R-SMA N-Connect
W721-1
RJ45
1 4 ● 1 x 1 6GK5721-1FC00-0AA0
6GK5721-1FC00-0AB0 (4)
W722-1
RJ45
1 4 ● (2) ● 1 x 1 6GK5722-1FC00-0AA0
6GK5722-1FC00-0AB0 (4)
W734-1
RJ45
2 8 ● (2) ● 2 x 2 6GK5734-1FX00-0AA0
6GK5734-1FX00-0AB0 (4)
W738-1
M12
2 8 ● (2) ● 2 x 2 6GK5738-1GY00-0AA0
6GK5738-1GY00-0AB0 (4)
W748-1
M12
3 8 ● 3 x 3 6GK5748-1GD00-0AA0
6GK5748-1GD00-0AB0 (4)
W748-1
RJ-45
3 8 ● 3 x 3 6GK5748-1FC00-0AA0
6GK5748-1FC00-0AB0 (4)
● suitable
(1) The iPCF mode provides an optimized data throughput and minimum handover times.
(2) With KEY-PLUG inserted
(3) In client mode
(4) US variant
Product overview
2.3 Active components
Passive network components IWLAN
20 System Manual, 08/2021, C79000-G8976-C282-08