Siemens SIMATIC 317TF-2 DP User manual

CPU 317TF-2 DP: Controlling a
SINAMICS S120 with Safety Functions
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
SIMATIC
A
utomation System S7-300
CPU 317TF-2 DP: Controlling a
SINAMICS S120 with Safety
Functions
Getting Started
07/2010
A5E02982990-01
Introduction 1
Preparation
2
Wiring
3
Configuration
4
Programming
5
Trial run
6
Further Information
7

Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation for the specific task, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E02982990-01
Ⓟ 08/2010
Copyright © Siemens AG .
Technical data subject to change

CPU 317TF-2 DP: Controlling a SINAMICS S120 with Safety Functions
Getting Started, 07/2010, A5E02982990-01 3
Table of contents
1 Introduction................................................................................................................................................ 5
2 Preparation................................................................................................................................................ 7
2.1 Requirements.................................................................................................................................7
2.2 Task .............................................................................................................................................10
3 Wiring ...................................................................................................................................................... 15
4 Configuration ........................................................................................................................................... 19
4.1 Setting up the T station with the help of a wizard ........................................................................19
4.2 Configuring the F-DI signal module .............................................................................................20
4.3 Configuring the F-DO signal module ...........................................................................................23
4.4 Configuring a drive in HW Config.................................................................................................25
4.5 Downloading the hardware configuration to the target hardware................................................26
4.6 Configuring a drive in S7T Config................................................................................................27
4.7 Message frame configuration of the drive....................................................................................42
4.8 Configuring safety-related communication between the TF-CPU and drives with safety
functions.......................................................................................................................................44
4.9 Configuring the properties of the TF-CPU ...................................................................................46
4.10 Interconnecting the safety data block with SINAMICS parameters.............................................47
4.11 Configuring safety functions on the drive.....................................................................................51
4.12 Configuring axes in S7T Config ...................................................................................................59
5 Programming ........................................................................................................................................... 69
5.1 Creating technology data blocks..................................................................................................69
5.2 Creating an S7 user program.......................................................................................................70
5.3 Editing the safety program...........................................................................................................71
6 Trial run ................................................................................................................................................... 77
7 Further Information .................................................................................................................................. 81

Table of contents
CPU 317TF-2 DP: Controlling a SINAMICS S120 with Safety Functions
4 Getting Started, 07/2010, A5E02982990-01

CPU 317TF-2 DP: Controlling a SINAMICS S120 with Safety Functions
Getting Started, 07/2010, A5E02982990-01 5
Introduction 1
These instructions provide a practical example guiding you through the commissioning tasks
required to create a fully functional application, and showing you how to perform a motion
with additional safety functions. It will help you get acquainted with operating CPU 317TF-2
DP and the SINAMICS S120 drive system.
Depending on your level of expertise, working through the sample will take between 4 and 5
hours.
Validity
The manual is valid for the following components:
● CPU 317TF-2 DP as of V2.7/4.1.5
● SINAMICS S120 as of V2.6.2
● S7 Technology as of V4.2
● S7 Distributed Safety as of V5.4 SP5 and S7 F Configuration Pack as of V5.5 SP7
Prerequisites
This document presumes that you have connected a SINAMICS S120 drive system to the
DP(DRIVE) interface of the CPU 317TF-2 DP.
We recommend the following manuals as preparation:
● Getting Started "CPU 317T-2 DP: Controlling an SINAMICS S120"
● Getting Started "S7 Distributed Safety"
● System manual "Safety Engineering in SIMATIC S7"

Introduction
CPU 317TF-2 DP: Controlling a SINAMICS S120 with Safety Functions
6 Getting Started, 07/2010, A5E02982990-01

CPU 317TF-2 DP: Controlling a SINAMICS S120 with Safety Functions
Getting Started, 07/2010, A5E02982990-01 7
Preparation 2
2.1 Requirements
Requirements
The following requirements must be fulfilled:
● You have an S7-300 station, consisting of:
– Power supply (PS), e.g. 6ES7307-1KA00-0AA0
– CPU 317TF-2 DP with memory card (4 MB or more), 6ES7317-6TF14-0AB0
V2.7/V4.1.5.
– Digital input module, safety-related (F-DI) with bus connector, for example,
6ES7326-1BK02-0AB0
– Digital output module, safety-related (F-DO) with bus connector, for example,
6ES7326-2BF10-0AB0
– Safety protector, 6ES7195-7KF00-0XA0
– Digital input module (DI) with bus connector, for example, 6ES7321-1BH02-0AA0
– Digital output module (DO) with bus connector, for example, 6ES7322-1BH01-0AA0
– Two optional front connectors for the digital modules
● For operating the safety functions, you need:
– Emergency stop, 2-channel - see the Configurator for pushbuttons and SIRIUS
3SB3/3SF5 indicator lamp in the Internet (https://mall.automation.siemens.com)
– Key switch, 2-channel - see the Configurator for pushbuttons and SIRIUS 3SB3/3SF5
indicator lamp in the Internet (https://mall.automation.siemens.com)
– 2 hinge position switches, 2-channel to monitor the protected zone door - see the
Configurator for position switches in the Internet
(https://mall.automation.siemens.com)

Preparation
2.1 Requirements
CPU 317TF-2 DP: Controlling a SINAMICS S120 with Safety Functions
8 Getting Started, 07/2010, A5E02982990-01
● A PG with MPI interface and properly installed software packages and commissioning
tools as listed below:
– STEP 7 as of V5.4 SP5
– S7 Technology as of V4.2
– Distributed Safety as of V5.4 SP5 with F Configuration Pack as of V5.5 SP7
● The PG is connected to the CPU via the MPI/DP interface (transmission rate up to 12
Mbps; default 187.5 kbps):
– PROFIBUS cable 6ES7901-4BD00-0XA0 (for transmission rates up to 12 Mbps)
● A SINAMICS S120 drive system with the following components is connected to the CPU
317TF-2 DP via the DP(DRIVE) interface:
– CU320 Control Unit with TB30 Terminal Board (6SL3040-0MA00-0AA1)
– Smart Line Module 5 kW (6SL3130-6AE15-0AA0)
– Single/Double Motor Module 3 A (6SL3120-2TE13-0AA3)
– 1 synchronous motor 1FK7022-5AK71-1AG3 with incremental encoder sin/cos 1 Vpp
via sensor module cabinet SMC20 (6SL3055-0AA00-5BA1) - optional
– 1 synchronous motor 1FK7022-5AK71-1LG3 with DRIVE-CLiQ interface: Absolute
encoder EnDat 512 pulses/revolution
– Reference loops for position monitoring
– Control box for setpoint/actual-value linkage via terminals
● SINAMICS S120 has the factory settings.

Preparation
2.1 Requirements
CPU 317TF-2 DP: Controlling a SINAMICS S120 with Safety Functions
Getting Started, 07/2010, A5E02982990-01 9
● You know the firmware version of your SINAMICS S120.
If you do not know the firmware version, you can find the version listed in the supplied
documents. Alternatively, you can open the "content.txt" file on the CF card. The firmware
version is in the "Internal Version" entry. You can find more detailed information on
reading the firmware version in the SINAMICS S120 product information.
Note
We have used a SINAMICS S120 training case as an example of a drive for this Getting
Started. The training case is available under the following order number:
Single-axis version with 1FK7 motor
6ZB2480-0AA00
2-axis version with 1FK7 motors
6ZB2480-0BA00
● The hardware is completely assembled and wired. For information, refer to
Getting
Started CPU 31x: Commissioning
.
● You provided hardware limit switches and EMERGENCY-OFF switches for safe and
reliable operation of the system. This EMERGENCY-OFF switch is independent of the
emergency stop switch described in the application example.
WARNING
Non-compliance with the regulations can result in serious injuries and damage to
machines and equipment.
Operation of an S7-300 as part of plants or systems is subject to special rules and
regulations, based on its field of application. Please note the current safety regulations
for the prevention of accidents, e.g. IEC 204 (EMERGENCY-OFF equipment).

Preparation
2.2 Task
CPU 317TF-2 DP: Controlling a SINAMICS S120 with Safety Functions
10 Getting Started, 07/2010, A5E02982990-01
2.2 Task
The example includes a technology task (positioning) with safety functions. The axis moves
in a production area with access control.
Technology task
The positioning requests are performed via two inputs:
● Start position at position 1 (0 mm)
● Start position at position 2 (5000 mm)
$
[LV
3RVLWLRQ 3RVLWLRQ
Other inputs are used to start or stop the axis.