Siemens SIMATIC NET CP 5614 A2 User manual

CP 5613 A2/CP 5614 A2
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC NET
PG/PC - PROFIBUS
CP 5613 A2/CP 5614 A2
Operating Instructions
08/2016
C79000
-G8976-C301-02
Preface
1
Description of the device
2
Software installation
3
Hardware installation
4
Configuration
5
Technical specifications
6
Certification
A

Siemens AG
Division Process Industries and Drive
s
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: C79000-G8976-C301
Ⓟ
09/2016 Subject to change
Copyright © Siemens AG 2016.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

CP 5613 A2/CP 5614 A2
Operating Instructions, 08/2016, C79000-G8976-C301-02 3
Table of contents
1 Preface ................................................................................................................................................... 5
2 Description of the device......................................................................................................................... 9
2.1 CP 5613 A2 product characteristics .........................................................................................9
2.2 CP 5614 A2 product characteristics .......................................................................................11
2.3 PROFIBUS interface...............................................................................................................12
2.4 Meaning of the LED display....................................................................................................13
3 Software installation.............................................................................................................................. 15
3.1 Installing the "SIMATIC NET PC Software"............................................................................15
3.2 Uninstalling the "SIMATIC NET PC Software"........................................................................16
4 Hardware installation............................................................................................................................. 17
4.1 Safety notices .........................................................................................................................17
4.2 Installing hardware..................................................................................................................18
4.2.1 Automatic adaptation of the bus clock speed .........................................................................18
4.2.2 Installing hardware PCI...........................................................................................................18
4.3 Hardware compatibility............................................................................................................19
4.3.1 Compatibility with other CPs...................................................................................................19
4.3.2 Replacement...........................................................................................................................19
5 Configuration ........................................................................................................................................ 21
6 Technical specifications ........................................................................................................................ 23
A Certification........................................................................................................................................... 27

Table of contents
CP 5613 A2/CP 5614 A2
4Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2
Operating Instructions, 08/2016, C79000-G8976-C301-02 5
Preface
1
What the consignment contains
The following components are supplied with the CP 5613 A2/CP 5614 A2:
●Communications processor CP 5613 A2/CP 5614 A2
●SIMATIC NET CD
●Certificate of license
Please check that the consignment you have received is complete. If the consignment is
incomplete, contact your supplier or your local Siemens office.
Validity of this documentation
These operating instructions are valid for the following products:
●CP 5613 A2
Article number: 6GK1 561-3AA01
●CP 5614 A2
Article number: 6GK1 561-4AA01
Content of this documentation
These operating instructions contain information about the installation and configuration of
the CP 5613 A2 and CP 5614 A2 communications processors.
Updated operating instructions on the Internet
You will find the current version of these operating instructions on the Product Support pages
under the following entry ID: 62612014
(https://support.industry.siemens.com/cs/ww/en/view/62612014)
Further documentation
The documents listed below contain more detailed information on commissioning and using
the communications processor. You will find this documentation on the Product Support
pages on the Internet under the following entry link:
Support (https://support.industry.siemens.com/cs/ww/en/ps)

Preface
CP 5613 A2/CP 5614 A2
6Operating Instructions, 08/2016, C79000-G8976-C301-02
Enter the entry ID shown below of the relevant manual as the search item.
●
Configuration manual Commissioning PC Stations
This provides you with detailed information on commissioning and configuring SIMATIC
NET PC communications modules.
Entry ID:
109488960 (https://support.industry.siemens.com/cs/ww/en/view/109488960)
●
System manual SIMATIC NET Industrial Communication with PG/PC
–
Volume 1– Basics
Entry ID:
77376110 (https://support.industry.siemens.com/cs/ww/en/view/77376110)
–
Volume 2– Interfaces
Entry ID:
77378184 (https://support.industry.siemens.com/cs/ww/en/view/77378184)
The system manuals introduce the topic of industrial communication and explain the
communications protocols used. There is also a description of the OPC interface as
user programming interface.
●
Installation manual "SIMATIC NET PC Software"
This document contains detailed information on installing the "SIMATIC NET
PC Software".
Entry ID:
77377602 (https://support.industry.siemens.com/cs/ww/en/view/77377602)
●
System manual PROFIBUS Network Manual
In this document you will find detailed information about setting up a PROFIBUS network.
Entry ID:
35222591 (https://support.industry.siemens.com/cs/ww/en/view/35222591)
SIMATIC NET documentation
You will find the entire SIMATIC NET documentation on the pages of Product Support:
15247 (https://support.industry.siemens.com/cs/ww/en/ps/15247)
Go to the required product group and make the following settings:
→Entry list →Entry type "Manuals / Operating Instructions"
Trademarks
The following and possibly other names not identified by the registered trademark sign ® are
registered trademarks of Siemens AG:
SIMATIC NET, HARDNET, SOFTNET, CP 1612, CP 1613, CP 5612, CP 5613, CP 5614,
CP 5622

Preface
CP 5613 A2/CP 5614 A2
Operating Instructions, 08/2016, C79000-G8976-C301-02 7
Industry Online Support
In addition to the product documentation, the comprehensive online information platform of
Siemens Industry Online Support at the following Internet address:
(http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=
en)
Apart from news, there you will also find:
●Project information: Manuals, FAQs, downloads, application examples etc.
●Contacts, Technical Forum
●The option submitting a support query:
(https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid
=38718979&caller=view)
●Our service offer:
Right across our products and systems, we provide numerous services that support you
in every phase of the life of your machine or system - from planning and implementation
to commissioning, through to maintenance and modernization.
You will find contact data on the Internet at the following address:
(http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en)
SITRAIN - Training for Industry
The training offer includes more than 300 courses on basic topics, extended knowledge and
special knowledge as well as advanced training for individual sectors - available at more
than 130 locations. Courses can also be organized individually and held locally at your
location.
You will find detailed information on the training curriculum and how to contact our customer
consultants at the following Internet address:
(www.siemens.com/sitrain)
SIMATIC NET glossary
Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
You will find the SIMATIC NET glossary on the Internet at the following address:
50305045 (https://support.industry.siemens.com/cs/ww/en/view/50305045)

Preface
CP 5613 A2/CP 5614 A2
8Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2
Operating Instructions, 08/2016, C79000-G8976-C301-02 9
Description of the device
2
2.1
CP 5613 A2 product characteristics
CP 5613 A2 characteristics
The CP 5613 A2 is a communications processor for connecting PCs to PROFIBUS. The
essential characteristics are as follows:
●The CP 5613 A2 is equipped with a PROFIBUS interface allowing up to 12 Mbps. It is
intended for operation in PGs and PCs with a PCI bus interface according to the PCI
standard V2.2.
●With the CP 5613 A2, up to 32 devices (PC, PG, SIMATIC S7 or ET 200) can be linked to
form a network segment. By linking several segments with repeaters, a maximum of 124
nodes can be connected.
●Optimized for fast DP master operation (DP Base) with up to 124 DP slaves with full data
consistency
●As an alternative, can also be used as a DP slave
●Relieves the PC due to event mechanisms (automatic detection of data changes)
●Fast logic support regardless of the user program (automatic linking of input and output
data can be set by the user program).
●Plug and play support during installation of the hardware
●Support of all data transmission speeds from 9.6 kbps to 12 Mbps
●Floating RS-485 connector
●Support of PCI 3.3 V/5 V, 33 MHz/66 MHz, 32 bit/64 bit and PCI-X 66 MHz, 32 bit/64 bit

Description of the device
2.1 CP 5613 A2 product characteristics
CP 5613 A2/CP 5614 A2
10 Operating Instructions, 08/2016, C79000-G8976-C301-02
CP 5613 A2 appearance
The following figure shows the CP 5613 A2 communications processor:
A
Yellow and green status LED
B
PROFIBUS interface 1 (master or slave)