Siemens DMS8000 MP4 Series User manual

Building Technologies
Fire Safety & Security Product
DMS8000 MP4.xx
Connectivity Guide Add-on
NICE/RIVER Digital Video Recorders

Data and design subject to change without notice. / Supply subject to availability.
© 2009 Copyright by
Siemens Building Technologies AG
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.

I
Building Technologies DMS8000 Video Connectivity Configuration Guide – NICE Add-on
Fire Safety & Security Products 06.2009
Table of contents
About this document...............................................................................................2
1Introduction.............................................................................................4
2Installation...............................................................................................4
2.1 Software installation..................................................................................4
2.1.1 Requirements .............................................................................4
2.1.2 Software License........................................................................4
2.1.3 NICE add-on installation.............................................................5
2.1.4 NICE add-on uninstall.................................................................5
3Configuration...........................................................................................6
3.1 Video integration.......................................................................................6
3.2 Video Network Manager ...........................................................................6
3.3 Video Drivers.............................................................................................7
3.4 Video components ....................................................................................7
3.5 NICE DVR configuration...........................................................................8
3.5.1 Configuration checklist ...............................................................8
3.5.2 Configuration procedure.............................................................8
3.6 Limitations...............................................................................................10
4Operations.............................................................................................11
4.1 MM8000 PTZ control panel.....................................................................11

2
Building Technologies DMS8000 Video Connectivity Configuration Guide –NICE Add-on
Fire Safety & Security Products 06.2009
About this document
Purpose of this document
This manual is a guide to the configuration procedures for the integration of NICE
and RIVER Video systems in MM8000 management stations.
This guide is part of the general DMS8000 documentation set which includes the
Composer Technical Manual, the other DMS8000 Connectivity Guides (Net-
work/Fire/Intrusion, Access Control, and OPC), and the Installation, Configuration,
and Commissioning manual (ICC) for each specific product.
Scope
This document applies to the MM8000 Management Station MP4.15 and higher.
Target audience
This documentation is intended for the following users:
- Project Managers
- Project Engineers
- Commissioning Personnel
Individuals performing the operations described in this manual are expected to
have prior expertise and training in the field of security, at least a moderate level of
familiarity with the Siemens Building Technologies product line, and experience
with the installation, configuration, and commissioning of security management
systems.
Documentation resource information
The DMS8000 Documentation Resource Information Guide document assem-
bles in one place important information regarding documentation resources. It con-
tains the following:
−Comprehensive definitions of the target audiences for FS DMS documents
−Training program information including the Siemens intranet link
−A complete list of all available DMS8000 documents
−Instructions for how to obtain a document via the Siemens intranet using the
STEP Documentation Repository System
−A map of relevant documents for each target audience group
−Customer Support links & resources
−A glossary containing definitions of all terms and acronyms used in
DMS8000 documentation
To access the DMS8000 Documentation Resource Information Guide (STEP
#A6V10089056), go to the link and follow the instructions below:
https://workspace.sbt.siemens.com/content/00001123/default.aspx
1. Click on the STEP WEB Client image:
2. Choose 04 Fire -3F from the Product Segment box and select Activate filter.
3. Select All in the Documents section of the Quick Search page and then
select Advanced Search.
4. Enter the document number in the Brochure No. field (e.g. A6V10089056) and
press Enter.

3
Building Technologies DMS8000 Video Connectivity Configuration Guide – NICE Add-on
Fire Safety & Security Products 06.2009
Operational and safety regulations
iBefore beginning work on the DMS8000 systems, you must have read and un-
derstood the related documents, in particular the Safety Regulations included in
the Installation, Configuration, and Commissioning manual (ICC) for each specific
product.
Liability disclaimer for damage or injuries
Before products are delivered, they are tested to ensure they function correctly
when used properly. Siemens disclaims all liability for damage or injuries caused
by the incorrect application of the instructions, or the disregard of danger adviso-
ries. This disclaimer applies in particular to personal injuries or damage caused by:
−Improper and/or incorrect use.
−Disregard of safety instructions in the documentation or on the product.
−Poor maintenance or a lack of maintenance.
We have checked the contents of this manual for agreement with the hardware and
software described. Since deviations cannot be precluded entirely, we cannot
guarantee full agreement. However, the data in this manual are reviewed regularly
and any necessary corrections included in subsequent editions. Suggestions for
improvement are welcome.
Modification index
Version Date Notes
A6V10097205_a_en 06.2009 Corresponds with DMS8000 MP4.20
A6V10097205_a_en 06.2008 Corresponds with DMS8000 MP4.15

4
Building Technologies DMS8000 Video Connectivity Configuration Guide –NICE Add-on
Fire Safety & Security Products 06.2009
1 Introduction
This is a guide to the software configuration procedures for the NICE and RIVER
Digital Video Recorders (DVR) in the MM8000 Management Station.
For a complete guide to the configuration process, this manual should be used with
the DMS8000 Network, Fire and Intrusion Guide, and with the Installation, Configu-
ration and Commissioning manual (ICC) of the specific product.
Video devices software version
The exact software version to use in the video device to integrate into the
DMS8000 systems is indicated in the latest MM8000 or MK8000 Release Notes.
2 Installation
The NICE/RIVER package is provided in the MM8000 product CD as add-on. It
can be installed using the standard Add-on Manager.
2.1 Software installation
2.1.1 Requirements
The NICE/RIVER application and driver software must be in place before installing
MM8000. In fact, the MM8000 setup provides for a customization of the (previously
installed) NICE/RIVER software environment. The list of the required applications
includes:
−PlayerComponentPackage.msi
−NiceVision API Package.exe
If the NICE/RIVER software is reinstalled or somehow modified, you can use the
Init_CCTV utility to customize the environment for MM8000 again.
→For information about Init_CCTV, refer to section 3.4.10 (Program Utilities) of
the MM8000 ICC, doc.no. A6V10062413_a_en.
2.1.2 Software License
MM8000 license must include specific items for the NICE/RIVER Add-on, for the
NS8016 driver, and for the required DVR units.
Therefore, the required license includes:
•WW8000 Composer (project configuration and download): Composer License
or Service key.
•MM8000 core, no. of subsystems.
This license should include the number of DVR units.
•NICE/RIVER add-on license.
•NS8016 driver license.
Other licenses, covering more MM8000 options, may or may not be used and they
are not related to the NICE/RIVER support.

5
Building Technologies DMS8000 Video Connectivity Configuration Guide – NICE Add-on
Fire Safety & Security Products 06.2009
2.1.3 NICE/RIVER add-on installation
The following are the installation procedures for the NICE/RIVER add-on module.
1. Start Add-on Manager; from the Windows Start menu, select the following:
Start ÆDMS8000 ÆTools ÆAdd-on Manager
The Add-on Manager window appears (Fig. 1).
2. In the list of add-ons Names, select Nice or River depending on which product
family you have to use. Note that the MM8000 Add-on software is the same for
the two.
Fig. 1 Add-on Manager Window
3. If your MM8000 installation includes a customized MM8000 internal account,
then deselect the default checkbox (Use default MM8000 User account) and
specify username and password.
→For information about the MM8000 Internal Account, refer to section 3.4.12
of the MM8000 ICC, doc.no. A6V10062413_a_en.
4. Click Install (or Update if a previous version is detected).
2.1.3.1 Multiple add-on’s installation
In general, it is possible to install multiple add-on packages and benefit of their
combined functionalities.
2.1.4 NICE/RIVER Add-on uninstall
The add-on module cannot be uninstalled.

6
Building Technologies DMS8000 Video Connectivity Configuration Guide –NICE Add-on
Fire Safety & Security Products 06.2009
3 Configuration
3.1 Video integration
The DMS8000 systems MM8000 and MK8000 can support the connection to
the following NICE video systems (and to the corresponding RIVER products
when applicable):
Manufacturer Model Device type
NICE NiceVision Alto Digital Video Recorder (DVR)
NICE NiceVision Pro Digital Video Recorder (DVR)
NICE NiceVision NVSat Digital Video Recorder (DVR)
NICE NiceVision NVR9000 Digital Video Recorder (DVR)
This integration allows providing advanced control capabilities as well as the
access to video images in MM8000 event treatment and navigation.
A detailed configuration guide for this video device is provided in this section.
3.2 Video Network Manager
The advanced video functionalities require a basic communication infrastructure
between MM8000/MK8000 and the CCTV units; this is actually a LAN network.
In Composer, a Video Network Manager (VNM) and the associated drivers should
be added to the MM8000/MK8000 main station in order to support the video net-
work communication. The drivers concern the NICE DVR units.
The Fig. 2 illustrates how to add the VNM to the configuration:
1. In the MM8000 physical configuration, select the main station name:
Supervisor System Settings ÆMM8000 System ÆPhysical configuration
Æ<Station name>
2. Click the button Ato add the VNM (see Fig. 2).
A new node is added. No further configuration is required for the VNM.
Fig. 2 Adding the Video Network Manager (A)
Note: Adding the VNM results in the entire Composer project being expanded in
order to support the CCTV functions. Particularly, the new tab Camera Extensor is
added to all nodes. Depending on the size of the configuration tree, the operation
may take a few minutes.
The Composer plug-in #251701 is required.

7
Building Technologies DMS8000 Video Connectivity Configuration Guide – NICE Add-on
Fire Safety & Security Products 06.2009
3.3 Video Drivers
The VNM can support the driver required to handle the network communication
with NICE/RIVER units. To add the driver to your project, proceed as follows:
1. Select the VNM node.
2. In the toolbar, click the icon corresponding to the NR driver (Fig. 3):
Fig. 3 Video drivers
A Select this icon to add the TELSCAN driver
B Select this icon to add the SISTORE driver
C Select this icon to add the NICE/RIVER driver
In small system, the Video Driver is installed on the MM8000 server. Large sys-
tems may include FEP stations with additional Video Drivers that can distribute the
traffic load. In the FEP station, the IP address must be configured:
1. Select the Video Driver node and then the Node tab.
2. In the Server Settings section, enter the FEP IP address in the Video LAN.
3.4 Video components
The Video menu of the Composer button bar on the left hand side includes the
available video component. Fig. 4 illustrates the menu options and the correspond-
ing components.
Fig. 4 CCTV components menu
A Select this icon to add a Camera folder
B Select this icon to add a Monitor folder
C Select this icon to add a NICE ( or RIVER) Digital Video Recorder
A
B
C

8
Building Technologies DMS8000 Video Connectivity Configuration Guide –NICE Add-on
Fire Safety & Security Products 06.2009
3.5 NICE/RIVER DVR configuration
3.5.1 Configuration checklist
Verify that you have satisfied the items needed in the first checklist before proceed-
ing to the configuration procedure that follows.
ITEMS NEEDED FOR CONFIGURATION
The NR Video driver installed and configured under the Video Network Manager
in Composer
The DVR IP address
The camera connections
Plug-ins needed:
– Plug-ins 258501 (NR driver) and 358201 (NICE/RIVER ST), which must be
installed before you can configure your system
3.5.2 Configuration procedure
The configuration of NICE and RIVER units is similar to the one for SISTORE DVR
that is described in the Video Connectivity Guide (doc.no. A6V10062457), although
the CCTV architecture can include multiple Video Drivers installed on various ma-
chines (MM8000 FEPs) on the network.
The following are the configuration procedures for a DVR unit:
Adding the folder for the DVR system
•Optionally, create a folder for the DVR unit.
Adding the DVR node
1. Select the new folder.
2. Click the Video menu
3. Select the NICE icon or RIVER icon to add a DVR node
Linking the DVR node
1. Expand the node structure including the NR Video Driver:
Supervisor System Settings ÆMM8000 System ÆPhysical configuration
Æ<Station name> ÆVideo Network Manager
2Select the DVR node.
3. Drag and drop the link to the Video Driver.
Configuring the DVR IP address
1. Select the new DVR node and click the Node tab.
Note: By default, the node will be named ‘Nice #nn’ or ‘River #nn’. In the Node
tab, you can customise the Description text.
2In the Setting section, enter the IP address,
which should match the value locally set in the DVR unit.

9
Building Technologies DMS8000 Video Connectivity Configuration Guide – NICE Add-on
Fire Safety & Security Products 06.2009
Connecting the cameras
1. Select and expand the DVR node.
2. Select and expand the DVR Video-in folder.
3. Add the required video inputs: note that input number can be customised.
4. Select and expand the Video Cameras folder.
5. Select the video-out node of the camera.
6. Drag and drop the ‘video signal’ to the DVR video-in node.
Fig. 5 Connecting cameras to video inputs
Video Monitors and Alarm I/O
Each DVR unit also includes monitors and alarm in/out objects. For the configura-
tion of these objects, you can also refer to the Video Connectivity Guide (doc.no.
A6V10062457).
Video camera coverage
The video camera coverage is configured graphically or via manual associations as
described in the Graphical Map Configuration (doc.no. A6V10062441).
Camera Extensor tab and Preset Position for event treatment
In the Camera Extensor tab of each node, you can see the camera associations
and manually add one or more cameras to the list associated with the selected
node. Also, for dome and PTZ motorised cameras, you can set the default Preset
Position where the camera is moved when is first selected during event treatment.
Refer to the point customization section of the MM8000 Installation, Configuration
and Commissioning manual (ICC, doc.no. A6V10062413) for more information
about the Camera Extensor tab.

10
Building Technologies DMS8000 Video Connectivity Configuration Guide –NICE Add-on
Fire Safety & Security Products 06.2009
3.6 Limitations
Currently, the support of NICE/RIVER DVR units is subject to the following limita-
tions (please check latest news with customer support):
•Maximum number of connectable DVR units per Server or FEP is 150 (100 rec-
ommended for best performance).
•Maximum number of AMS Server is 4.
•Special types of alarms (e.g. traffic, baggage, intrusion) are all mapped in
MM8000 as motion detection alarms.
•Data and time synchronisation fails if a registration is in progress on the DVR
unit.
•Redundant AMS Servers cannot be supported, which means that a
NICE/RIVER DVR can be associated to one AMS Server only.
•Only 1 playback per station at the time is possible, even when quad-view is
used.

11
Building Technologies DMS8000 Video Connectivity Configuration Guide – NICE Add-on
Fire Safety & Security Products 06.2009
4 Operations
4.1 MM8000 PTZ control panel
MM8000 operations are described in the MM8000 Operation Manual (document
no. A6V10062409).
When operating with NICE/RIVER video systems in event treatment and plant
browsing, a specific control panel is provided for the cameras equipped with PTZ
control features. Fig. 6 here below illustrates the control commands available in the
panel.
Preset positions
zSelect predefined position using the drop-down
menu
zEnter the names of new positions in the empty
field
zClick Del to delete the currently selected position
zClick Set to store new positions
Speed adjustment
zClick +to speed up motion and –to slow it down
Zoom/Focus control
zClick +or –to adjust the camera Zoom
zClick +or –to adjust the camera Focus
Pan / Tilt
Click the Arrow buttons to Pan/Tilt the camera and
reach any required position.
Fig. 6 Cameras control commands

Siemens Switzerland Ltd
Building Technologies Group
International Headquarters
Fire Safety & Security Products
Gubelstrasse 22
CH-6301 Zug
Tel [phone]
Fax [phone]
www.sbt.siemens.com
Document no. A6V10097205_a_en DMS8000 Technical Material
Edition 06.2009 Section 4