Siemens 986-88301A User manual

Installation Instructions
Document No. 565-709
December 1, 2006
Andover InfinetDriver
These installation instructions only cover the
connection of the Andover Infinet Driver to the
Andover system. For hardware installation of the
Modular Equipment Controller, see document number
565-570. For hardware installation of the Power
Open Processor, see document number 565-571.
Product Description
The Andover Infinet Driver enables communication
between the APOGEE®Automation System and the
Andover network.
Product Numbers
986-88301A Andover Infinet Driver, Open
Processor with RS-485 ALN
986-88301B Andover Infinet Driver, Open
Processor with Ethernet ALN
986-88301C Andover Infinet Driver, MEC
with RS-485 ALN, 8DI, 8DO,
8AI, 8AO, point expansion
support, HOA-ready
986-88301D Andover Infinet Driver, MEC
with RS-485 ALN, 8DI, 8DO,
8AI, 8AO, point expansion
support, with HOA
986-88301E Andover Infinet Driver, MEC
with RS-485 ALN, 8DI, 8DO,
8AI, 8AO, point expansion
support, modem, HOA-ready
986-88301F Andover Infinet Driver, MEC
with RS-485 ALN, 8DI, 8DO,
8AI, 8AO, point expansion
support, modem, with HOA
986-88301G Andover Infinet Driver, MEC
with Ethernet ALN, 8DI, 8DO,
8AI, 8AO, point expansion
support, HOA-ready
986-88301H AndoverInfinet Driver, MEC
with Ethernet ALN, 8DI, 8DO,
8AI, 8AO, point expansion
support, with HOA
Warning/Caution Notations
WARNING:
Personal injury/loss of life may occur if you
do not follow the procedures as specified.
CAUTION:
Equipment damage or loss of data may
occur if you do not follow the procedures
as specified.
Expected Installation Times
30 minutes.
Required Tools and Materials
• Flat-blade screwdriver (1/8-inch blade width).
• Wire strippers.
• Cabling and connectors. See the Connecting
the Andover Infinet Driver to the Andover
Network section.
CAUTION:
Always wear an electro-static discharge
wrist strap and discharge accumulated
static before touching field panel
components.
Prerequisites
• Driver hardware is installed according to its
respective installation instructions.
•FLNTerm
ination blocks installed, if any.
Depending on the type of installation, other
prerequisites may have to be completed.
Item Number: 565-709, Rev. AA Page 1 of 2

Document No. 565-709
Installation Instructions
December 1, 2006
Connecting the Andover Infinet
Driver to the Andover Network
Follow these steps to connect the Andover Infinet
Driver to the Andover network:
1. Make cables per diagram in Figure 1.
2. Connect cables per diagram in Figure 1.
DRIVER
+
-
S
+
-
SHLD
+-S
Infinet/Infinet II Device
(6xx, 8xx, 9xx)
To Other
Infinet/Infinet II
Devices
GW1400R1
FLN 1
Figure 1. Connecting the Andover Infinet Driver to the Andover Network.
Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as
design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners.
© 2006 Siemens Building Technologies, Inc.
Siemens Building Technologies, Inc. Your feedback is important to us. If you have Document No. 565-709
1000 Deerfield Parkway comments about this document, please send Country of Origin: US
Buffalo Grove, IL 60089-4513 them to SBT_[email protected]. Page 2 of 2
U.S.A.