Siemens NCU 7x0.3 PN Series User manual

 
NCU 7x0.3 PN
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
SINUMERIK
SINUMERIK 840D sl
NCU 7x0.3 PN
Manual
Valid for
SINUMERIK 840D sl / 840DE sl control
Software Version
CNC software 4.4
09/2011
6FC5397-1EP40-0BA0
Preface
Safety notes
1
System overview
2
Description
3
Application planning
4
Dimension drawings
5
Assembling
6
Connecting
7
Technical data
8
Connectable components
9
Spare Parts/Accessories
10
Appendix
A

Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the relevant information is not taken into account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
order number: 6FC5397-1EP40-0BA0
Ⓟ 07/2011
Copyright © Siemens AG 2011.
Technical data subject to change

NCU 7x0.3 PN
Manual, 09/2011, 6FC5397-1EP40-0BA0 3
Preface
SINUMERIK documentation
The SINUMERIK documentation is organized in the following categories:
● General documentation
● User documentation
● Manufacturer/service documentation
Additional information
You can find information on the following topics at
http://www.siemens.com/motioncontrol/docu:
● Ordering documentation/overview of documentation
● Additional links to download documents
● Using documentation online (find and search in manuals/information)
Please send any questions about the technical documentation (e.g. suggestions for
improvement, corrections) to the following address:
mailto:[email protected]m
My Documentation Manager (MDM)
Under the following link you will find information to individually compile OEM-specific
machine documentation based on the Siemens content:
http://www.siemens.com/mdm
Training
For information about the range of training courses, refer to:
● http://www.siemens.com/sitrain
SITRAIN - Siemens training for products, systems and solutions in automation technology
● http://www.siemens.com/sinutrain
SinuTrain - training software for SINUMERIK
FAQs
You can find Frequently Asked Questions in the Service&Support pages under Product
Support.
http://support.automation.siemens.com

Preface
NCU 7x0.3 PN
4 Manual, 09/2011, 6FC5397-1EP40-0BA0
SINUMERIK
You can find information on SINUMERIK under the following link:
http://www.siemens.com/sinumerik
Target group
This documentation is intended for manufacturers of machine tools, particularly:
● Project engineers, electricians and installers
● Maintenance and service personnel
Benefits
The information in this manual facilitates installation and connection of the SINUMERIK
840D numerical control in the control cabinet.
Standard scope
This documentation only describes the functionality of the standard version. Extensions or
changes made by the machine tool manufacturer are documented by the machine tool
manufacturer.
Other functions not described in this documentation might be executable in the controller.
This does not, however, represent an obligation to supply such functions with a new
controller or when servicing.
Further, for the sake of simplicity, this documentation does not contain all detailed
information about all types of the product and cannot cover every conceivable case of
installation, operation or maintenance.
Technical Support
You will find telephone numbers for other countries for technical support in the Internet under
http://www.siemens.com/automation/service&support
EC Declaration of Conformity
The EC Declaration of Conformity for the EMC Directive can be found on the Internet at:
http://support.automation.siemens.com
Here, enter the number 15257461 as the search term or contact your local Siemens office.

NCU 7x0.3 PN
Manual, 09/2011, 6FC5397-1EP40-0BA0 5
Table of contents
Preface ...................................................................................................................................................... 3
1 Safety notes............................................................................................................................................... 9
1.1 Danger notices...............................................................................................................................9
1.2 ESD notices .................................................................................................................................11
2 System overview...................................................................................................................................... 13
2.1 Application....................................................................................................................................13
2.2 System configuration ...................................................................................................................14
2.3 Variants........................................................................................................................................16
2.4 Ordering data ...............................................................................................................................17
3 Description............................................................................................................................................... 19
3.1 Characteristics .............................................................................................................................19
3.2 Illustration.....................................................................................................................................20
3.3 Type plates...................................................................................................................................21
3.4 Operator control and display elements ........................................................................................22
3.4.1 Overview of operating and display elements...............................................................................22
3.4.2 LED displays ................................................................................................................................23
3.4.3 7-segment display........................................................................................................................24
3.4.4 RESET button ..............................................................................................................................25
3.4.5 Start-up and mode selector switch ..............................................................................................25
4 Application planning................................................................................................................................. 27
4.1 Secondary electrical conditions ...................................................................................................27
4.1.1 Grounding concept.......................................................................................................................27
4.1.2 RI suppression measures ............................................................................................................28
4.2 Climatic and mechanical environmental conditions.....................................................................29
4.2.1 Shipping and storage conditions..................................................................................................29
4.2.2 Operating conditions ....................................................................................................................31
4.3 Recycling and disposal ................................................................................................................31
5 Dimension drawings ................................................................................................................................ 33
6 Assembling.............................................................................................................................................. 35
6.1 Safety information ........................................................................................................................35
6.2 Designs ........................................................................................................................................36
6.3 Mounting control unit using spacers ............................................................................................36
6.4 Mounting the Control Unit without spacers..................................................................................37
6.5 Mounting the Control Unit for segregated heat removal..............................................................38

Table of contents
NCU 7x0.3 PN
6 Manual, 09/2011, 6FC5397-1EP40-0BA0
7 Connecting .............................................................................................................................................. 41
7.1 Overview ..................................................................................................................................... 41
7.2 Safety information for wiring........................................................................................................ 43
7.3 Opening the front cover............................................................................................................... 44
7.4 Power supply............................................................................................................................... 45
7.4.1 Application................................................................................................................................... 45
7.4.2 Requirements for the power supply ............................................................................................ 46
7.4.3 Connecting the power supply...................................................................................................... 48
7.5 DRIVE-CLiQ components ........................................................................................................... 49
7.5.1 Application................................................................................................................................... 49
7.5.2 Connectable DRIVE-CLiQ components...................................................................................... 51
7.6 Use of Ethernet interfaces........................................................................................................... 52
7.7 PROFINET .................................................................................................................................. 55
7.7.1 Application................................................................................................................................... 55
7.7.2 PROFINET cables....................................................................................................................... 57
7.7.3 Preparing the twisted pair cables................................................................................................ 58
7.7.4 Example PROFINET CBA configuration..................................................................................... 60
7.8 PROFIBUS DP............................................................................................................................ 61
7.8.1 Application................................................................................................................................... 61
7.8.2 PROFIBUS cables and connectors............................................................................................. 63
7.8.3 Connection components in PROFIBUS...................................................................................... 64
7.8.4 Rules for the laying of PROFIBUS cables ..................................................................................65
7.8.5 Connecting PROFIBUS DP......................................................................................................... 66
7.8.6 Disconnecting stations from the PROFIBUS .............................................................................. 67
7.8.7 Operating the X136 interface as MPI.......................................................................................... 67
7.9 Digital inputs/outputs................................................................................................................... 69
7.9.1 DIO application............................................................................................................................ 69
7.9.2 Block diagram ............................................................................................................................. 72
7.9.3 Connecting digital inputs/outputs ................................................................................................ 73
7.9.4 Technical data............................................................................................................................. 74
7.10 USB............................................................................................................................................. 76
7.11 Measuring sockets ...................................................................................................................... 77
8 Technical data ......................................................................................................................................... 79
9 Connectable components ........................................................................................................................ 81
9.1 NX10.3 / NX15.3 ......................................................................................................................... 81
9.1.1 Description .................................................................................................................................. 81
9.1.2 Dimension drawing...................................................................................................................... 85
9.1.3 Mounting...................................................................................................................................... 86
9.1.4 Connection .................................................................................................................................. 88
9.1.5 Technical Data ............................................................................................................................ 93
9.2 PP 72/48D PN............................................................................................................................. 93
9.2.1 Description .................................................................................................................................. 93
9.2.2 Mounting...................................................................................................................................... 96
9.2.3 Connecting .................................................................................................................................. 98
9.2.3.1 Interface overview ....................................................................................................................... 98

Table of contents
NCU 7x0.3 PN
Manual, 09/2011, 6FC5397-1EP40-0BA0 7
9.2.3.2 X1 power supply ..........................................................................................................................99
9.2.3.3 X2 PROFINET............................................................................................................................101
9.2.3.4 X111, X222 and X333 digital inputs/outputs..............................................................................104
9.2.4 Parameter assignment...............................................................................................................111
9.2.4.1 Input / output images .................................................................................................................111
9.2.4.2 Diagnostics via input image .......................................................................................................112
9.2.5 Technical data............................................................................................................................113
9.3 PP 72/48D 2/2A PN ...................................................................................................................114
9.3.1 Description .................................................................................................................................114
9.3.2 Dimension drawing ....................................................................................................................117
9.3.3 Mounting ....................................................................................................................................118
9.3.4 Connection.................................................................................................................................118
9.3.4.1 Interface overview......................................................................................................................118
9.3.4.2 X1 power supply ........................................................................................................................119
9.3.4.3 X2 PROFINET............................................................................................................................122
9.3.4.4 X111, X222 and X333 digital inputs/outputs..............................................................................125
9.3.4.5 Analog X3 inputs/outputs ...........................................................................................................131
9.3.5 Parameter assignment...............................................................................................................136
9.3.5.1 Input / output images .................................................................................................................136
9.3.5.2 Assigning parameters to the analog inputs / outputs.................................................................138
9.3.5.3 Analog value representation ......................................................................................................140
9.3.5.4 Examples ...................................................................................................................................143
9.3.5.5 Diagnostics via input image .......................................................................................................145
9.3.6 Technical data............................................................................................................................147
9.4 COM01.3 RS 232C (V.24) module ............................................................................................147
9.4.1 Description .................................................................................................................................147
9.4.2 Installation/Mounting ..................................................................................................................150
9.4.3 Connection.................................................................................................................................151
9.5 CBE30-2.....................................................................................................................................152
9.5.1 Description .................................................................................................................................152
9.5.2 Installation/Mounting ..................................................................................................................154
9.5.3 Connection.................................................................................................................................156
9.6 TM15 Terminal Module..............................................................................................................157
9.7 Terminal Module TM120 ............................................................................................................157
9.8 DRIVE-CLiQ Hub Module DMC20.............................................................................................158
9.9 DME20 DRIVE-CLiQ Hub Module.............................................................................................158
10 Spare Parts/Accessories ....................................................................................................................... 159
10.1 Dual fan/battery module.............................................................................................................159
10.1.1 Using the dual fan/ battery module ............................................................................................159
10.1.2 Replacing the dual fan/ battery module .....................................................................................160
10.2 CompactFlash Card ...................................................................................................................162
10.2.1 Properties of the CompactFlash card ........................................................................................162
10.2.2 Inserting the CompactFlash card...............................................................................................163

Table of contents
NCU 7x0.3 PN
8 Manual, 09/2011, 6FC5397-1EP40-0BA0
A Appendix................................................................................................................................................ 165
A.1 Abbreviations ............................................................................................................................ 165
A.2 Documentation overview........................................................................................................... 167
Index...................................................................................................................................................... 169

NCU 7x0.3 PN
Manual, 09/2011, 6FC5397-1EP40-0BA0 9
Safety notes 1
1.1 Danger notices
The following notices are intended firstly for your personal safety and secondly to prevent
damage occurring to the product described or any connected devices and machines. Non-
observance of the warnings can result in severe personal injury or property damage.
DANGER
Only appropriately qualified personnel may commission/start-up SINUMERIK equipment.
The personnel must take into account the information provided in the technical customer
documentation for the product, and be familiar with and observe the specified danger and
warning notices.
When electrical equipment and motors are operated, the electrical circuits automatically
conduct a dangerous voltage.
When the system is operating, dangerous axis movements may occur throughout the entire
work area.
A potential fire hazard exists due to the energy being transferred in the equipment and the
work materials used.
All work on the electrical system must be performed after the system has been switched off
and disconnected from the power supply.
DANGER
Proper transportation, expert storage, installation and mounting, as well as careful
operation and maintenance are essential for this SINUMERIK device to operate correctly
and reliably.
The details in the catalogs and proposals also apply to the design of special equipment
versions.
In addition to the danger and warning information provided in the technical customer
documentation, the applicable national, local, and system-specific regulations and
requirements must be taken into account.
Only protective extra-low voltages (PELVs) that comply with EN 61800-5-1 can be
connected to all connections and terminals between 0 and 48 V.
Should it be necessary to test or take measurements on live equipment, then the
specifications and procedural instructions defined in Accident Prevention Regulation BGV
A2 must be adhered to, in particular § 8 "Permissible deviations when working on live
components". Suitable electric tools should be used.

Safety notes
1.1 Danger notices
NCU 7x0.3 PN
10 Manual, 09/2011, 6FC5397-1EP40-0BA0
WARNING
Power cables and signal lines should be installed in such a way that inductive and
capacitive interference does not in any way impair the automation and safety functions.
WARNING
Repairs to devices that have been supplied by our company may only be carried out by
Siemens customer service or by repair centers authorized by Siemens. When replacing
parts or components, only use those parts that are included in the spare parts list.
Before opening the device, always disconnect the power supply.
Emergency stop/off devices which comply with EN 60204 / IEC 60204 (VDE 0113-1) must
remain effective in all automation equipment operating modes. The act of releasing the
emergency stop/off device must not cause an uncontrolled or undefined hot restart.
Additional external measures must be taken, or devices must be created that enforce a
safe operational state even when there is a fault (e.g. using independent limit value
switches, mechanical locks, etc.) at any location in the automation equipment where faults
might cause major material damage or even physical injury, in other words, where faults
could be dangerous.

Safety notes
1.2 ESD notices
NCU 7x0.3 PN
Manual, 09/2011, 6FC5397-1EP40-0BA0 11
1.2 ESD notices
CAUTION
The modules contain electrostatically sensitive devices. Discharge yourself of electrostatic
energy before touching the components. The easiest way to do this is to touch a
conductive, grounded object immediately beforehand (for example, bare metal parts of
control cabinet or the protective ground contact of a socket outlet).
NOTICE
Handling ESD-modules:
When handling electrostatically sensitive devices, make sure that operator, workplace
and packing material are properly grounded.
Generally, electronic modules must not be touched unless work has to be carried out on
them. When handling PCBs make absolutely sure that you do not touch component pins
or printed conductors.
Touch components only if:
– You are permanently grounded via an ESD armband
– You are wearing ESD shoes or ESD shoe-grounding-strips, if ESD flooring is
available
Modules may only be placed on electrically conductive surfaces (table with ESD top,
conductive ESD foam plastic, ESD packaging bags, ESD transport containers).
Keep modules away from visual display units, monitors or TV sets (minimum distance
from screen 10 cm).
Do not bring ESD-sensitive modules into contact with chargeable and highly-insulating
materials, such as plastic, insulating table tops or clothing made of synthetic materials.
Measurements on modules are allowed only if:
– The measuring instrument is properly earthed (e.g., protective conductor) or
– Before measuring with a floating measuring instrument, the probe is briefly
discharged (e.g., touch the bare metal parts of the control housing).

Safety notes
1.2 ESD notices
NCU 7x0.3 PN
12 Manual, 09/2011, 6FC5397-1EP40-0BA0

NCU 7x0.3 PN
Manual, 09/2011, 6FC5397-1EP40-0BA0 13
System overview 2
2.1 Application
Features
SINUMERIK 840D sl offers modularity, openness, flexibility, and uniform structures for
operation, programming, and visualization. It provides a system platform with trend-setting
functions for almost all technologies.
Integrated into the SINAMICS S120 drive system and complemented by the SIMATIC S7-
300 automation system, the SINUMERIK 840D sl forms a complete digital system that is
best suited for the mid to upper performance range.
The SINUMERIK 840D sl is characterized by:
● A high degree of flexibility
● Excellent dynamic response and precision
● Optimum integration into networks
Integrated and certified SINUMERIK Safety Integrated safety functions are available with
SINUMERIK 840D sl. Consequently, highly effective protection for personnel and machines
is achieved in a simple, economical, and practical manner.
Operating and programming software such as ShopMill or ShopTurn, as well as Motion
Control Information System Products (MCIS-Products) can be used for the production
sector.
Fields of application
The SINUMERIK 840D sl can be used worldwide for turning, drilling, milling, grinding, laser
machining, nibbling, punching, in tool and mold making, for high-speed cutting applications,
for wood and glass processing, for handling operations, in transfer lines and rotary indexing
machines, for mass production and JobShop production.
The SINUMERIK 840DE sl is available as an export version for use in countries requiring an
export authorization.

System overview
2.2 System configuration
NCU 7x0.3 PN
14 Manual, 09/2011, 6FC5397-1EP40-0BA0
2.2 System configuration
SINUMERIK 840D sl combines CNC, HMI, PLC, closed-loop control, and communication
tasks within a single NCU (Numerical Control Unit).
Components
For operation, programming, and visualization purposes, the corresponding operating
software is already integrated into the CNC software for the NCU and therefore runs on the
high-performance NCU multi-processor module. For increased operating performance, the
SINUMERIK PCU 50.3 industrial PC can be used.
Up to 4 distributed OPs can be operated on one NCU / PCU. The operator panel can be
installed as a Thin Client at a distance of up to 100 m.
6,180(5,.'VO
ZLWK
6,1$0,&66
6HUYRPRWRUV
3RZHUVXSSO\
6,180(5,.RSHUDWRUSDQHOIURQWVZLWK7&8
0DLQVSLQGOHPRWRU
352),%86
6,1$0,&66
(7SUR
,QGXVWULDO(WKHUQHW
352),1(7
1;
1&8
ವವವ
ವವವ
'5,9(&/L4
6,180(5,.
+7
6,180(5,.
3&8
Figure 2-1 Typical topology of the SINUMERIK 840D sl complete system

System overview
2.2 System configuration
NCU 7x0.3 PN
Manual, 09/2011, 6FC5397-1EP40-0BA0 15
The following system configuration is only possible with an NCU 710.3 PN possible:
3+
VSLQGOHPRWRU
).
IHHGPRWRUV
).
IHHGPRWRUV
6,180(5,.RSHUDWRU
SDQHOVZLWK7&8
3RZHUVXSSO\
6,1$0,&66
0RWRU0RGXOH
ERRNVL]HFRPSDFW
IRUPDW
,QGXVWULDO(WKHUQHW
6,0$7,&
(7SUR
'5,9(&/L4
6,180(5,.
+7
6,180(5,.
3&8
33'31
33b'b$b31
6,180(5,.
'VO
1&831
6,1$0,&66
&RPEL
352),1(7
Figure 2-2 Example, topology with NCU 710.3 PN
The following components can be attached to the Control Unit:
● SINUMERIK operator panel front with TCU/PCU 50.3 and Machine Control
Panel/Machine Push Button Panel
● SIMATIC thin client (as of firmware V1.4)
● SIMATIC CE panel
● SINUMERIK handheld units
● Distributed PLC I/O via PROFIBUS DP or PROFINET IO
● SINUMERIK I/O modules PP 72/48D PN and PP 72/48D 2/2A PN
● SINUMERIK Analog Drive Interface for 4 Axes ADI 4
● SINAMICS 120 drive system
● Feed and main spindle motors
– 1FT / 1FK / 1FN / 1FW6 / 1FE1 / 2SP1 synchronous motors
– 1PH / 1PM induction motors

System overview
2.3 Variants
NCU 7x0.3 PN
16 Manual, 09/2011, 6FC5397-1EP40-0BA0
The SINUMERIK 840D sl offers integrated PROFINET functionality. Supported:
● PROFINET CBA
The CBA functionality integrated in the NCU allows users to modularize machinery and
systems: Rapid real-time communication (up to 10 ms) between the controllers means
that systems lend themselves better to standardization and can be reused or expanded
more easily. Response to customer demands is faster and more flexible and startup is
simplified and speeded up by pretesting at component level.
● PROFINET IO
As part of PROFINET, PROFINET IO is a communication concept that is used to
implement modular, distributed applications. PROFINET IO is based on Industrial
Ethernet and allows distributed field and I/O equipment to be connected to the central
processing unit.
128 PROFINET IO devices can be operated on the NCU as an IO controller.
2.3 Variants
The scalability of the hardware and software – both from a CNC perspective and in terms of
operation – means the SINUMERIK 840D sl can be used in many sectors. The possibilities
range from simple positioning tasks up to complex multi-axis systems.
Application areas and performance
● As many as 8 axes can be implemented on an NCU 710. The NCU 710 can be expanded
by up to 2 NX modules. One possible benefit would be increased drive control
performance.
● On the NCU 720/730, the number of axes and/or the performance of the drive controller
can be increased to 31 axes. This is achieved through the use of the NX modules. The
NCU 720/730 can be expanded by up to 5 NX modules for increased performance of the
drive control and number of axes.
● Use of an NCU 730 is recommended for maximum dynamics and accuracy in mold
making or in the high speed cutting sector.
The following table shows the essential features of the various Control Units:
Table 2- 1 Versions
Property NCU 710 .3 PN NCU 720.3 PN NCU 730.3 PN
Cooling ribs No No Yes
DRIVE CLiQ ports 4 6 6
Axes Up to 8 Up to 31 Up to 31
NX10.3 / 15.3 Up to 2 Up to 3/Up to 5 Up to 3/Up to 5
TCU Up to 2 Up to 4 Up to 4

System overview
2.4 Ordering data
NCU 7x0.3 PN
Manual, 09/2011, 6FC5397-1EP40-0BA0 17
2.4 Ordering data
Table 2- 2 Order data for system components
System components Order numbers
NCU 710.3 PN with PLC 317-3DP/PN 6FC5371-0AA30-0AA0
NCU 720.3 PN with PLC 317-3DP/PN 6FC5372-0AA30-0AA0
NCU 730.3 PN with PLC 317-3DP/PN 6FC5373-0AA30-0AA0
Numeric Control Extension NX15.3 (High Extension) 6SL3040-1NB00-0AA0
Numeric Control Extension NX10.3 (Standard Extension) 6SL3040-1NC00-0AA0
COM01.3 RS232C(V.24) module for NCU 7x0.3 PN 6FC5312-0FA01-1AA0
CBE30-2 Link module 6FC5312-0FA00-2AA0
TS Adapter IE ISDN with integrated ISDN terminal adapter 6ES7972-0ED00-0XA0
TS Adapter IE Modem with integrated analog modem 6ES7972-0EM00-0XA0
USB-FlashDrive 8 GB, USB 2.0 6ES7648-0DC50-0AA0
Table 2- 3 Ordering data for spare parts
Spare parts Order numbers
Dual fan/battery module 6FC5348-0AA02-0AA0
Battery 6FC5247-0AA18-0AA0
Seal for segregated heat removal 6FC5348-0AA07-0AA0
Spacer for NCU 730.3 PN 6FC5348-0AA06-0AA0
Spacer for NCU 710.3 PN and NCU 720.3 PN 6SL3064-1BB00-0AA0
Front cover 6FC5348-0AA30-0AA0
Blanking plate for BOP 6SL3064-3BB00-0AA0
Cover for optional guide frame 6SL3064-3CB00-0AA0
Dust protection, blanking plug (50 pcs.) for DRIVE-CLiQ interfaces 6SL3066-4CA00-0AA0
PROFIBUS/MPI plug connector with terminating resistor 6ES7972-0BB41-0XA0
CompactFlash Card 8 GB empty 6FC5313-6AG00-0AA0
Terminal kit, consisting of connectors X122 /X124 / X132 and dust
cover, blanking plugs for DRIVE-CLiQ interfaces
6SL3064-2CB00-0AA0
CNC user memory expansion 2 MB 6FC5800-0AD00-0YB0
PLC user memory expansion 128 KB 6FC5800-0AD10-0YB0
Ordering options
The products can also be ordered online:
● Industry Mall: http://www.siemens.com/industrymall
● Spares On Web: http://workplace.automation.siemens.de/sparesonweb

System overview
2.4 Ordering data
NCU 7x0.3 PN
18 Manual, 09/2011, 6FC5397-1EP40-0BA0

NCU 7x0.3 PN
Manual, 09/2011, 6FC5397-1EP40-0BA0 19
Description 3
3.1 Characteristics
A Control Unit has the following elements:
● Battery-backed real-time clock
● Slot for a CompactFlash Card (behind the blanking cover)
● DRIVE-CLiQ interfaces for connecting to the drive
● Interfaces for operation behind a hinged front cover:
– Ethernet ports
– PROFINET interfaces
– PROFIBUS interfaces
– Digital inputs/outputs (6 of which can be parameterized as inputs for probe and
BERO)
● Commissioning interfaces:
– Ethernet interface (behind blanking cover)
– Measuring sockets

Description
3.2 Illustration
NCU 7x0.3 PN
20 Manual, 09/2011, 6FC5397-1EP40-0BA0
3.2 Illustration
The following diagram shows an NCU 730.3 PN with its interfaces and control and display
elements (fault displays and status indicators). Please ensure that the structure of the NCUs
is virtually identical. There are only a few discrepancies, as follows:
● The NCU 710.3 PN has 4 instead of 6 DRIVE-CliQ interfaces.
● NCU 710.3 PN and NCU 720.3 PN have no cooling ribs.
'LDJQRVWLFVEXWWRQ
0$&DGGUHVVHV
6SDFHU
2SWLRQVORWFRYHUHG
;
352),%86'303,LQWHUIDFH
/('GLVSOD\V
7\SHSODWH
3/&PRGHVHOHFWRUVZLWFK
;
'RXEOHIDQEDWWHU\PRGXOH
;XQGHUVLGH
56QRIXQFWLRQ
5HVHWEXWWRQ
3RWHQWLDOFRQQHFWLRQ
VHJPHQWGLVSOD\
;b3
31,(
(WKHUQHWLQWHUIDFH
1&.FRPPLVVLRQLQJVZLWFK
;
6ORWIRU&RPSDFW)ODVK
&DUG
;XQGHUVLGH
7770
PHDVXULQJVRFNHWV
;OHIW;ULJKW
[86%LQWHUIDFH
;
352),%86'3LQWHUIDFH
;33
352),1(7,2LQWHUIDFH
;
(OHFWURQLFVSRZHUVXSSO\
;;;
'LJLWDOLQSXWVRXWSXWV
6KLHOGVXSSRUW
;;
'5,9(&/L4LQWHUIDFHV
;3
31,(1(7
(WKHUQHWLQWHUIDFH
;3
31,(23
(WKHUQHWLQWHUIDFH
&RROLQJULEV
Figure 3-1 Illustration showing the NCU 730.3 PN